Pulsed pumped Yb-doped fiber amplifier at low repetition rate

A pulsed pumped Yb-doped double-clad fiber (DCF) master-oscillator power amplifier (MOPA) at low repetition rate is reported. Seeded by a passive Q-switched Nd:YAG microchip laser, the fiber amplifier can generate 167-kW peak-power and 0.83-ns duration pulses at 200-Hz repetition rate. Because of the pulsed pump approach, the amplified spontaneous emission (ASE) and the spurious lasing between pulses are well avoided, and the repetition rate can be set freely from single-shot to 1 kHz. Peak power scaling limitations that arise from the fiber facet damage are discussed.     

100 W全光纤声光调Q光纤激光器实验研究

 报道了一台全光纤结构主振荡功率放大(MOPA)型掺镱脉冲光纤激光器,以光纤光栅为腔镜,光纤型声光调Q的光纤激光器为种子源,通过两级掺镱双包层光纤放大器实现功率放大。对声光调Q的光纤激光器输出特性进行了研究,比较了不同泵浦波长、不同重复频率对激光输出功率和脉冲宽度的影响,并实现了最短脉冲宽度25 ns、单脉冲能量45 μJ的脉冲激光输出。在重复频率50 kHz时,对脉冲宽度130 ns、平均功率0.6 W的种子光进行放大,得到了平均功率102.5 W、脉冲宽度约240 ns的激光输出。     

一种基于增益调制技术的全光纤化脉冲Yb光纤激光器

以波长为975 nm的半导体激光器作为泵浦源,周期性地脉冲泵浦一个包含Yb掺杂光纤和光纤光栅对的Yb光纤激光器,实现了基于增益调制技术的全光纤化高功率Yb光纤激光器的稳定脉冲输出.在50 kHz重频下,采用20 W的泵浦功率和2.4 μs的泵浦脉冲宽度,获得了1 060 nm波长脉冲宽度仅100 ns的稳定脉冲激光输出,单脉冲激光能量约为20 μJ.以此作为脉冲激光种子进行功率放大,获得了性能稳定的全光纤结构高功率脉冲激光输出,放大后单脉冲能量超过200 μJ,激光放大器斜率效率达到60%.     

大模面积掺Yb3+双包层光纤激光器的实验研究

本文研究了在连续泵浦和脉冲泵浦两种情况下, 大模面积（LMA）掺Yb³⁺双包层光纤激光器的输出特性. 采用连续泵浦, 在最大泵浦功率为10.4 W时, 得到了平均功率4.6 W、中心波长1.09 μm的准连续激光输出. 采用脉冲泵浦, 得到了脉宽小于50 ns、峰值功率为5.3 kW、重复频率为5 kHz、单脉冲能量为0.26 mJ的稳定的调Q脉冲输出.     

窄线宽纳秒脉冲光纤拉曼放大器的理论模型和数值分析

窄线宽纳秒脉冲光纤拉曼放大器在非线性频率变换、遥感探测和量子信息等领域有广泛的应用前景.综合考虑受激拉曼散射(stimulated Raman scattering,SRS)、受激布里渊散射(stimulated Brillouin scattering,SBS)、自相位调制(self-phase modulation)和交叉相位调制(cross-phase modulation)等非线性效应,建立了窄线宽纳秒脉冲光纤拉曼放大器的非线性动力学模型.仿真分析了放大器中脉冲激光的时频演化特性,对比研究了抽运脉冲宽度、光纤长度和信号光功率等因素对放大器性能的影响.研究发现,上述因素会影响放大器的SRS阈值、SBS阈值、输出激光线宽、激光转换效率等.例如,当脉冲宽度为800 ns时,SBS随着抽运功率的增加而发生,限制了激光功率的提升;减短抽运脉宽可以抑制SBS,但是输出激光的线宽易于展宽到数百MHz以上;增加光纤长度可以获得更低的SRS阈值和更高的转换效率,但是SBS效应和光谱展宽程度也随之增强.系统搭建中需要平衡各非线性效应,选择合适的系统参数.研究内容可以为窄线宽纳秒脉冲光纤拉曼放大器的设计搭建提供参考.     

High frequency fiber laser emission generated by pump spiking

A stable and short pulse train of ∼100 MHz repetition frequency was obtained from an erbium doped fiber laser excited by a “continuous” semiconductor laser and by using a linear cavity defined by a Bragg grating pair. The operation frequency of the fiber laser was greater (∼5-15 times) than the cavity round-trip frequency. Emission properties obtained from the erbium doped fiber laser were correlated with those taken from the pump laser, which presented a particular optical noise (very short pulses) added to the continuous emission. From the temporal and radio-frequency analysis of both systems, we conclude that the pump emission characteristics are the responsible of the fiber laser pulsed behaviour.     

Toward higher-order passive harmonic mode-locking of a soliton fiber laser

We report >13 MHz/mW pump power efficiency in increasing the repetition rate of passive harmonic mode-locking by engineering the soliton pulse energy in Er fiber lasers incorporating carbon nanotube saturable absorber. Stable pulses with a ～5 GHz repetition rate and 40 dB of super-mode suppression are demonstrated with only ～400 mW pump power in a single-clad fiber laser.     

High Power Er/Yb Codoped Double Clad Fiber Pulsed Amplifier Based on an All-Fiber Configuration

We report an all-fiber two-stage high power pulsed amplifier, seeded with a 1550nm, 1 kHz repetition rate rectangular pulse, and based on Er/Yb co-doped double clad fiber. All the characteristics are measured in the experiment. The maximal slope efficiency is 22.56%, which is the highest we know of at such a low repetition rate, and the maximal output signal power is 1W. The various factors that affect the pulsed amplifier performance are analyzed. A high output power while keeping high power conversion efficiency can be obtained with careful selection of the input power, pump power and repetition rate. The experimental results show that the crucial parameters should be optimized when designing all-fiber pulsed amplifiers.     

星光Ⅱ装置激光能量测量实时采集和数据传输系统

介绍一套激光能量实时采集和多路传输通信系统。该系统兼容现有的不同型号和规格的激光能量计,具有峰值保持和功率积分功能,抗干扰能力强,可实现数据自动采集、处理及长距离多点传送。为实现激光能量测量精密化和自动化打下了技术基础。     

Investigation of the pump wavelength influence on pulsed laser pumped Alexandrite lasers

Recent theoretical modelling and experimental results have shown that excess lattice phonon energy created dur ing the non-radiative energy transfer from the ⁴T₂ pump manifold to the ²E storage level in Alexandrite when pumped with wavelengths shorter than ∼645 nm causes chaotic lasing output. Shorter pump wavelengths have also been associated with increased non-radiative energy decay and reduced laser efficiency. We report studies of fluorescence emission spectra of Alexandrite illuminated at a range of wavelengths from green to red, which demonstrate reduced fluorescence yield for shorter pump wavelengths at elevated crystal temperatures. Investigations of pulsed laser pumping of Alexandrite over the same spectral range demonstrated reduced pump threshold energy for longer pump wavelengths. High repetition rate pulsed pumping of Alexandrite at 532, 578 and 671 nm showed stable and efficient laser performance was only achieved for red pumping at 671 nm. These results support the theoretical model and demonstrate the potential for scalable, red laser pumped, all-solid-state Alexandrite lasers.PACS 42.60.Lh; 42.60.Mi     

Extractable energy from erbium-ytterbium co-doped pulsed fiber amplifiers and lasers

An analytic model is developed for evaluating the extractable energy from high energy pulsed erbium-ytterbium co-doped fiber amplifiers and lasers. The energy extraction capabilities under the limitation of spurious lasing, due to amplified spontaneous emission (ASE), are mapped for various numerical apertures, single and multi transverse mode evolution and operating wavelengths. The model provides an assessment for the maximum pulse energy that can be extracted from a given erbium-ytterbium co-doped fiber. In addition, the model can be used to determine the repetition rate and optimal length, under which the laser source will be optimally operated in order to achieve a required extracted energy, without spurious lasing. The results show a clear advantage in using 915 nm wavelength pump source over 975 nm, at high average power operation, due to augmented 1 μm ASE at 975 nm pump wavelength, as a result of the Yb³⁺ population inversion.     

A compact graphene Q-switched erbium-doped fiber laser using optical circulator and tunable fiber Bragg grating

We demonstrate a passively Q-switched tunable erbium-doped fiber laser(EDFL)based on graphene as a saturable absorber(SA).A three-port optical circulator(OC)and a strain-induced tunable fiber Bragg grating(TFBG)are used as the two end mirrors in an all-fiber linear cavity.The Q-switched EDFL has a low pump threshold of 23.8 mW.The pulse repetition rate of the fiber laser can be widely changed from 9.3 kHz to 69.7 kHz by increasing the pump power from23.8 mW to 219.9 mW.The minimum pulse duration is 1.7μs and the highest pulse energy is 25.4 nJ.The emission wavelength of the laser can be tuned from 1560.43 nm to 1566.27 nm by changing the central wavelength of the straininduced TFBG.     

增益调制高重频脉冲光纤激光器实验研究

采用脉冲泵浦方案,研制出了基于增益调制技术的全光纤结构高重频脉冲激光器。采用电路直接调制的激光二极管作为泵浦源,双包层光纤作为增益介质,构造了光纤光栅选模的线形腔结构。实验中通过调整泵浦光脉冲宽度和光纤激光器谐振腔长度,得到了稳定的高重频脉冲。在100kHz重复频率下,采用21W的峰值泵浦功率和2.5μs的泵浦脉冲宽度,获得了1.06μm波长,脉冲宽度247ns的稳定脉冲激光输出。脉冲峰值功率一致性好,平均功率长期功率稳定性为2%。观察并分析了由于纵模拍频在脉冲包络上产生的次脉冲特性。通过一级放大实现89.6 W输出。     

高阶模抑制型MILO慢波结构高频特性分析北大核心CSCD

理论分析了高阶模抑制型磁绝缘线振荡器(MILO)慢波结构,推导了其各分区电磁场分布.通过对场分布的进一步分析可以发现,角向开槽使得原始MILO结构中的两个简并的HEM11模式去简并,分裂成为极化方向与开槽方向垂直或平行的两个模式;通过改变慢波结构叶片间开槽角向位置相对关系,可以破坏高阶模式之间π模谐振关系,从而抑制高阶模式的起振,使器件稳定工作在基模.     

Nanosecond optical parametric oscillator based on large-aperture periodically poled RbTiOAsO(4)

We report on optical parametric oscillators (OPO's) based on periodically poled RbTiOAsO(4) (PP RTA), which are pumped by Q -switched solid-state lasers. With a diode-pumped Nd:YVO(4) laser (pulse energy, 800microJ ; pulse duration, 5.5 ns; repetition rate, 1 kHz) the PP RTA OPO generated 1.58-microm signal and 3.26-microm idler radiation with a signal pulse energy of 45microJ . The large aperture of 3 mmx3 mm of the PP RTA crystal also permitted OPO operation with pump pulse energies as high as 65 mJ, provided by a flash-lamp-pumped Q -switched Nd:YAG laser (pulse duration, 20 ns; repetition rate, 10 Hz). With this pump source the OPO generated signal pulse energies as high as 17 mJ, corresponding to an efficiency of 26%. The performance of this OPO shows that large-aperture PP RTA crystals are well suited for pulsed nanosecond OPO operation with pump pulse energies of tens of millijoules.     

High-power pulsed diode-pumped Er:ZBLAN fiber laser

We report on the operation and performance of a gain-switched Er:ZBLAN fiber laser based on an active pulsed diode pump system. The produced laser pulses offer high peak powers while retaining the high average powers and efficiency of the cw regime. The measured pulse duration was about 300 ns and nearly independent of the pump repetition frequency. The maximum obtained 68 W of peak power is the highest reported, to our knowledge, for diode-pumped Er:ZBLAN fiber lasers, and the 2 W of average power at the repetition frequency of 100 kHz is 2 orders of magnitude higher than previously reported average power in a pulsed regime. The obtained slope efficiency was 34%.     

二极管泵浦双掺杂YAG微片自调Q激光器

 利用激光二极管泵浦双掺杂YAG微片晶体，在连续泵浦时获得了重复频率为2.78kHz，脉冲宽度为6ns的自调Q激光输出。并通过预泵浦加脉冲调制电流的方法，实现可控重复率的自调Q脉冲输出。与外腔式自调Q微片激光器相比，这种一体化微片激光器具有更高的转换效率、更窄的输出脉冲宽度和更高的重复频率，同时结构更为简单紧凑，易于调整。     

Several hundred kHz repetition rate nanosecond pulses amplification in Er–Yb co-doped fiber amplifier

We have experimentally investigated several hundred kHz repetition rate 1,550-nm nanosecond pulses amplification in Er–Yb co-doped fiber amplifier (EYDFA). The experimental setup has three stage fiber amplifiers. At the output of the second stage EYDFA, Yb³⁺ ions induced amplified spontaneous emission (Yb-ASE) is not observed owing to the low pump power. In the third stage EYDFA, a simultaneously seeded 1,064-nm continuous-wave laser is used to control Yb-ASE. Without any additional 1,064-nm signal, significantly backward Yb-ASE which caused loss-induced heat accumulation at the input port of the pump combiner can be observed. The monitored temperature at the input port of the pump combiner rapidly grows from 30 to 80 °C when the pump power is turned from 20 to 32 W. When a 196-mW forward 1,064-nm laser is added, the monitored backward Yb-ASE power is significantly declined, and the monitored temperature is kept below 35 °C. But, the additional signal caused a large power fraction at 1,064 nm in the output laser. In our experiment at the maximum pump power of 48.5 W, the total output power is 20 W with ~6.4-W 1,550-nm pulsed laser and ~13-W 1,064-nm continuous-wave laser.     

Narrow-linewidth widely tunable hybrid Q-switched double-clad fiber laser

A laser-diode-pumped Yb-doped double-clad fiber laser operating in a hybrid Q-switched regime has been demonstrated. With pulsed pump light and stimulated Brillouin scattering of the gain fiber as the Q-switching mechanisms, the laser generated nanosecond pulses with a stable repetition rate. A single-pulse energy of as much as 143.1 microJ with a peak power of 28.6 kW was obtained. Use of an external-cavity diffraction grating in the Littman configuration permitted tuning of the laser wavelength over a 15.7-THz range from 1080 to 1140 nm, and a linewidth of 0.04 nm over the whole tuning range was achieved.     

高功率光纤激光器中ASE噪声的测量方法（英）

高峰值功率脉冲光纤激光器在激光雷达系统中有着广泛的应用。然而,光纤激光器中放大自发辐射噪声（ASE）严重影响了系统的探测性能。提出一种测量高峰值功率脉冲光纤激光器中ASE噪声的方法。在该方法中,首先对高峰值功率的激光脉冲衰减,然后在时域分别测量和计算ASE噪声和激光脉冲的相对能量。给出了光纤激光器在驱动电流分别为6 A,7 A和8 A时衰减后的ASE噪声廓线以及ASE噪声占激光脉冲能量的比例。