Conductive macroporous composite chitosan-carbon nanotube scaffolds

Multiwalled carbon nanotubes (MWCNTs) were used as doping material for three-dimensional chitosan scaffolds to develop a highly conductive, porous, and biocompatible composite material. The porous and interconnected structures were formed by the process of thermally induced phase separation followed by freeze-drying applied to an aqueous solution of 1 wt % chitosan acetic acid. The porosity was characterized to be 97% by both mercury intrusion porosimetry measurements and SEM image analysis. When MWCNTs were used as a filler to introduce conductive pathways throughout the chitosan skeleton, the solubilizing hydrophobic and hydrophilic properties of chitosan established stable polymer/MWCNT solutions that yielded a homogeneous distribution of nanotubes throughout the final composite matrix. A percolation theory threshold of approximately 2.5 wt % MWCNTs was determined by measurement of the conductivity as a function of chitosan/MWCNT ratios. The powder resistivity of completely compressed scaffolds also was measured and was found to be similar for all MWCNT concentrations (0.7-0.15 Omega cm powder resistivity for MWCNTs of 0.8-5 wt %) and almost five times lower than the 20 k Omega cm value found for pure chitosan scaffolds.     

Melt‐crystallization mechanism of poly(ethylene terephthalate)/multi‐walled carbon nanotubes prepared by in situ polymerization

A series of poly(ethylene terephthalate)/multi‐walled carbon nanotubes (PET/MWCNTs) nanocomposites were prepared by in situ polymerization using different amounts of multi‐walled carbon nanotubes (MWCNTs). The polymerization of poly(ethylene terephthalate) (PET) was carried out by the two‐stage melt polycondensation method. The intrinsic viscosity (IV) of the composites is ranged between 0.31 and 0.63 dL/g depending on the concentration of the MWCNTs. A decrease of IV was found by increasing MWCNTs content. This is due to the reactions taking place between the two components leading to branched and crosslinked macromolecules. These reactions are, mainly, responsible for thermal behavior of nanocomposites. The melting point of the nanocomposites was shifted to slightly higher temperatures by the addition till 0.55 wt % of MWCNTs while for higher concentration was reduced. The degree of crystallinity in all nanocomposites was, also, reduced by increasing MWCNTs amount. However, from crystallization temperature, it was found that MWCNTs till 1 wt % can enhance the crystallization rate of PET, whereas at higher content (2 wt %), the trend is the opposite due to the formation of crosslinked macromolecules. From the extended crystallization analysis, it was proved that MWCNTs act as nucleating agents for PET crystallization. Additionally, the crystallization mechanism due to the existence of MWCNT becomes more complicated because two mechanisms with different activation energies are taking place in the different degrees of crystallization, depending on the percentage of MWCNT. The effect of molecular weight also plays an important role. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1452–1466, 2009     

In situ polymerization of methyl methacrylate/multi-walled carbon nanotube composites using cationic stearyl methacrylate copolymers as dispersants

Novel water-soluble amphiphilic copolymers (poly[(stearyl methacrylate)-stat-([2-(methacryloyloxy)ethyl] trimethyl ammonium iodide)]) for dispersing multi-walled carbon nanotubes (MWCNTs) were used to carry out in situ methyl methacrylate (MMA) polymerization. The morphology of the poly(methyl methacrylate)/MWCNT composites and the dispersion of the MWCNTs were analyzed by transmission electron microscopy. The dispersion of multi-walled carbon nanotubes in the composites was excellent for cationic SMA (stearyl methacrylate) copolymers, even at high MWCNT loading (6.0 wt.%). The mechanical properties and electrical and thermal conductivities of the composites were also analyzed. Mechanical properties were improved by MWCNTs; the strain at break values remained stable up to 6.0 wt.% MWCNT loading. Both electrical and thermal conductivities were improved by the addition of MWCNTs.     

Crystallization and morphology of iPP/MWCNT prepared by compounding iPP melt with MWCNT aqueous suspension

In this work, isotactic polypropylene (iPP) composites filled with multiwalled carbon nanotubes (MWCNTs) were prepared by compounding iPP melt with MWCNT aqueous suspension using a corotating twin-screw extruder, and the morphology and crystallization behavior of the composites were investigated. Scanning electron microscopy micrographs showed that MWCNTs dispersed individually at nanoscale in the iPP matrix when the MWCNTs concentration was low, though MWCNTs aggregates were detected when the filler concentration increased. The results of differential scanning calorimetry, wide-angle X-ray diffraction, and polarized light microscopy indicated that the β-form crystal of iPP was induced by MWCNTs at the concentration of 0.1 wt.% which was dispersed individually in the iPP matrix. At higher content, however, MWCNTs acted as α-nucleating agent, and the crystals in the iPP/MWCNT composites showed higher degree of perfection than that of pure iPP though smaller in dimension. Crystallization rate of iPP increased significantly with increasing MWCNT content.     

Influence of modification of MWCNTs on the structure and performance of MWCNT‐Poly(MMA‐AM) hybrid membranes

Hybrid membranes containing multi‐walled carbon nanotubes (MWCNTs) were initially prepared to separate benzene/cyclohexane mixtures. Subsequently, MWCNT surfaces were chemically modified using two methods to change the surface polarity of the MWCNTs and improve the distribution thereof in Poly(methylmethacrylate) (PMMA). This change consequently enhanced the separation performance of hybrid membranes with MWCNTs. Raman spectroscopy was used to characterize the structure of the pristine MWCNTs and the modified MWCNTs. The morphology and distribution of the MWCNTs in PMMA were investigated by transmission electron microscopy. The results showed that the addition of MWCNTs clearly improved the separation performance of the hybrid membranes. Surface modification introduced polar groups onto the MWCNT surface, which significantly improved the distribution of MWCNTs in the PMMA membranes and the performance of hybrid membranes. MWCNTs with higher surface polarity also increased the amount of MWCNTs distributed homogeneously in PMMA. Aminated MWCNTs (MWCNT‐NH₂) showed the highest surface polarity. Thus, the content of MWCNT‐NH₂ well distributed in PMMA was the highest among the three types of MWCNTs. The highest separation factor for the hybrid membranes with 1.0 wt% MWCNT‐NH₂ was about seven times that of membranes containing pristine MWCNTs. Copyright © 2013 John Wiley & Sons, Ltd.     

Binary Au/MWCNT and Ternary Au/ZnO/MWCNT Nanocomposites: Synthesis,Characterisation and Catalytic Performance

Gold nanoparticles of 10–24 and 5–8 nm in size were obtained by chemical citrate reduction and UV photoreduction, respectively, on acid‐treated multiwalled carbon nanotubes (MWCNTs) and on ZnO/MWCNT composites. The shape and size of the deposited Au nanoparticles were found to be dependent upon the synthetic method used. Single‐crystalline, hexagonal gold particles were produced in the case of UV photoreduction on ZnO/MWCNT, whereas spherical Au particles were deposited on MWCNT when the chemical citrate reduction method was used. In the UV photoreduction route, n‐doped ZnO serves as the e^? donor, whereas the solvent is the hole trap. All materials were fully characterised by UV/Vis spectroscopy, scanning electron microscopy, transmission electron microscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy and BET surface analysis. The catalytic activity of the composites was studied for the selective hydrogenation of α,β‐unsaturated carbonyl compound 3,7‐dimethyl‐2,6‐octadienal (citral). The Au/ZnO/MWCNT composite favours the formation of unsaturated alcohols (selectivity=50 % at a citral conversion of 20 %) due to the presence of single‐crystalline, hexagonal gold particles, whereas saturated aldehyde formation is favoured in the case of the Au/MWCNT nanocomposite that contains spherical gold particles.     

Isotactic polypropylene/carbon nanotube composites prepared by latex technology: Electrical conductivity study

Several series of nanocomposites were prepared using a latex-based process, the main step of which consisted of mixing an aqueous suspension of exfoliated carbon nanotubes (CNTs) and a polymer latex. In the present work, a systematic study on the electrical properties of fully amorphous (polystyrene - PS) as well as semi-crystalline (isotactic polypropylene - iPP) nanocomposites containing either single-wall (SWCNTs) or multi-wall carbon nanotubes (MWCNTs) has been conducted. Percolation thresholds as low as 0.05 wt.% or 0.1 wt.% were observed for SWCNT/iPP and MWCNT/iPP nanocomposites, respectively. The formation of a conductive percolating network at such a low CNT concentration is favored by the high intrinsic conductivity and the low viscosity of the polymer matrix. The electrical percolation threshold of the iPP-based system was found to be lower than its rheological percolation threshold. Beyond the percolation threshold, MWCNT-based nanocomposites generally exhibited higher conductivity levels than those based on SWCNTs, most probably due to the higher intrinsic conductivity of the MWCNTs as compared to that of the SWCNTs. These excellent electrical properties, associated with the strong nucleating effect of the CNTs reported earlier [1] and [2], render this type of nanocomposites extremely attractive from a technological point of view.     

The effect of oxidation on physicochemical properties and aqueous stabilization of multiwalled carbon nanotubes: comparison of multiple analysis methods

Surface oxidation can alter physicochemical properties of multiwalled carbon nanotubes (MWCNTs) and influence their aqueous stabilization. Many techniques have been used to characterize the physicochemical properties and aqueous stabilization of MWCNTs. However, the relationship between the change in physicochemical property and the aqueous stabilization of MWCNTs merits more studies, and the multiple characterization techniques have not been well compared. This study systematically and comparatively investigated the effect of oxidation on the physicochemical properties and aqueous stabilization of MWCNTs using multiple analysis methods. Increased surface area, disclosed tube ends, defects on the sidewalls, disruption of the electronic structure, and removal of metal catalysts and amorphous carbon were observed for the oxidized MWCNTs (o-MWCNTs) using the multipoint Brunauer-Emmett-Teller (BET) method, transmission electron microscope observation, Raman spectroscopy, UV-Vis spectroscopy, and thermogravimetric analysis. An oxidation-time-dependent increase in oxygen content of the MWCNTs was verified by the methods of elemental analysis, mass difference calculation, and X-ray photoelectron spectroscopy (XPS). Fourier transform infrared spectroscopy, XPS, and the Boehm titration were employed to study the functionalities on the MWCNT surfaces. Despite the limitations of these techniques, the results indicated that the dramatic increase in carboxyl groups was mainly responsible for the significant increase in oxygen content after the oxidation. The dissociation of the grafted functional groups increased electronegativity of the o-MWCNTs and facilitated the aqueous stabilization of o-MWCNTs through electrostatic repulsions. The oxidation affected the UV-Vis absorbance of MWCNT suspensions. The absorbances at 800 nm of the stabilized MWCNT suspensions had a good correlation with the MWCNT concentrations and could be used to quantify the MWCNT suspensions. The findings of this work are expected to boost the research on carbon nanotubes and their environmental behaviors.     

The effect of MWCNT on dynamic mechanical properties and crystallinity of in situ polymerized polyamide 12 nanocomposite

This work aims at investigating the dynamic mechanical properties of in situ anionic ring opening polymerized polyamide 12 in the presence of multi‐walled carbon nanotubes (MWCNT). According to the dynamic mechanical thermal analysis results, the addition of only 0.1 wt.% of MWCNTs led to 30% enhancement in modulus at room temperature which exhibited improved mechanical behavior of the nanocomposites. Test results showed that by the presence of 1.2% wt MWCNTs, the modulus is almost doubled, and it did not show any tangible changes by the addition of more nanotubes. Also, the effect of different frequencies on the viscoelastic behavior was investigated in order to determine the thermal transitions occurred in the synthesized nanocomposites. After that, the crystallinity of the samples has been studied using differential scanning calorimetry and X‐ray diffraction data in order to investigate the effect of MWCNT content on the crystals' dimension.     

Electrical and rheological percolation of PMMA/MWCNT nanocomposites as a function of CNT geometry and functionality

Composites of poly(methyl methacrylate) (PMMA) with multi-walled carbon nanotubes (MWCNT) of varying aspect ratio and carboxylic acid functionality were prepared using melt mixing. The extent of dispersion and distribution of the MWCNTs in the PMMA matrix was investigated using a combination of high-resolution transmission electron microscopy (HRTEM), wide-angle X-ray diffraction (XRD) and Raman spectroscopy. The electrical resistivity and oscillatory shear rheological properties of the composites were measured as a function of MWCNT geometry, functionality, and concentration. The fundamental ballistic conductance of the pristine free-standing MWCNTs was investigated using a mechanically controlled break-junction method. The electrical conductivity of PMMA was enhanced by up to 11 orders of magnitude for MWCNT concentrations below 0.5 wt.%. MWCNTs having higher aspect ratio, above 500, or functionalized with carboxylic acid groups readily formed rheological percolated networks with thresholds, determined from a power law relationship, of 1.52 and 2.06 wt.%, respectively. The onset of pseudo-solid-like behaviour and network formation is observed as G′, η∗, and tan δ⁻¹ are independent of frequency as MWCNT loading increased. Sufficiently long and/or functionalized tubes are required to physically bridge or provide interfacial interactions with PMMA to alter polymer chain dynamics. Carboxylic acid functionalization disrupts the crystalline order of MWCNTs due to a loss of π-conjugation and electron de-localisation of sp² C-C bonds resulting in non-ballistic electron transport in these tubes, irrespective of how highly dispersed they are in the PMMA matrix.     

The Localization Behavior of Different CNTs in PC/SAN Blends Containing a Reactive Component

Co-continuous blend systems of polycarbonate (PC), poly(styrene-co-acrylonitrile) (SAN), commercial non-functionalized multi-walled carbon nanotubes (MWCNTs) or various types of commercial and laboratory functionalized single-walled carbon nanotubes (SWCNTs), and a reactive component (RC, N-phenylmaleimide styrene maleic anhydride copolymer) were melt compounded in one step in a microcompounder. The blend system is immiscible, while the RC is miscible with SAN and contains maleic anhydride groups that have the potential to reactively couple with functional groups on the surface of the nanotubes. The influence of the RC on the localization of MWCNTs and SWCNTs (0.5 wt.%) was investigated by transmission electron microscopy (TEM) and energy-filtered TEM. In PC/SAN blends without RC, MWCNTs are localized in the PC component. In contrast, in PC/SAN-RC, the MWCNTs localize in the SAN-RC component, depending on the RC concentration. By adjusting the MWCNT/RC ratio, the localization of the MWCNTs can be tuned. The SWCNTs behave differently compared to the MWCNTs in PC/SAN-RC blends and their localization occurs either only in the PC or in both blend components, depending on the type of the SWCNTs. CNT defect concentration and surface functionalities seem to be responsible for the localization differences.     

Catalytic pyrolysis of polypropylene to synthesize carbon nanotubes and hydrogen through a two-stage process

A two-stage reaction process was used to convert polypropylene (PP) into multi-walled carbon nanotubes (MWCNTs) and hydrogen-rich gas. The proposed process consisted of two stages: catalytic pyrolysis of PP over HZSM-5 zeolite in a screw kiln reactor and the subsequent catalytic decomposition of pyrolysis gases over a nickel catalysts in a moving-bed reactor for producing MWCNTs and hydrogen. The resultant gas mainly consisted of hydrogen and methane. SEM and TEM images revealed that carbon products in the moving-bed reactor were in the form of MWCNTs. XRD and TGA characterization indicated that high decomposition temperature resulted in the formation of more highly crystalline nanotubes. The influence of pyrolysis temperature (550-750 °C) and decomposition temperature (500-800 °C) on the performances of the two-stage reaction system were investigated. The MWCNT yield and hydrogen concentration increased with an increase in the decomposition temperature and reached a maximum at 700 °C. With increasing pyrolysis temperature the yield of pyrolysis gas increased while the liquid yield decreased. The yield of MWCNTs in the moving-bed reactor was determined by both the quantity and quality of the pyrolysis gas.     

Dispersion of multi-wall carbon nanotubes by an ionic liquid-based polyether in aqueous solution

Multi-wall carbon nanotubes (MWCNTs) can be effectively dispersed by an ionic liquid-based polyether, poly(1-glycidyl-3-methylimidazolium chloride) (PGMIC) in aqueous solution. The amount of dispersed MWCNTs increases with the increasing of PGMIC concentration, and then decreases. Reaggregation of MWCNTs is observed when PGMIC exceeded the optimal concentration, which may be due to the conformational change of PGMIC molecules around MWCNT. The ultrasonic dispersion method is better than stirring method in the PGMIC solution. Furthermore, the acidic solution is convenient to prepare stable MWCNTs suspensions. Through the characterizations of ultraviolet–visible–near infrared, thermogravimetric analysis and Fourier transform infrared, it can be concluded that electrostatic repulsions, hydrophobic effect, n–π, and cation–π interactions played important roles in the dispersion of MWCNTs.     

Structural and morphological studies on the deformation behavior of polypropylene/multi‐walled carbon nanotubes nanocomposites prepared through ultrasound‐assisted melt extrusion process

Structural and morphological behavior under stress–strain of polypropylene/multi‐walled carbon nanotubes (PP/MWCNTs) nanocomposites prepared through ultrasound‐assisted melt extrusion process was studied by means of optical microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, small angle X‐ray scattering (SAXS), and wide angle X‐ray scattering (WAXS). A high ductile behavior was observed in the PP/MWCNT nanocomposites with low concentration of MWCNTs. This was related to an energy‐dissipating mechanism, achieved by the formation of an ordered PP‐CNTs interphase zone and crystal oriented structure in the undeformed samples. Different strain‐induced‐phase transformations were observed by ex situ SAXS/WAXS, characterizing the different stages of structure development during the deformation of PP and PP/MWCNTs nanocomposites. The high concentration of CNTs reduced the strain behavior of PP due to the agglomeration of nanoparticles. A structural pathway relating the deformation‐induced phase transitions and the dissipation energy mechanism in the PP/MWCNTs nanocomposites at low concentration of nanoparticles was proposed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 475–491     

Significant enhancement of electrical and thermal conductivities of polyethylene carbon nanotube composites by the addition of a low amount of silver nanoparticles

Electrically and thermally conductive high‐density polyethylene composites filled with hybrid fillers, multiwall carbon nanotubes (MWCNTs) and silver nanoparticles (Ag‐NPs), have been prepared in the melt state. The investigation of their electrical and thermal conductivities while comparing with high‐density polyethylene/MWCNT binary composites shows that the addition of only 3 vol% of Ag‐NPs does not reduce the electrical percolation threshold (P_c) that remains as low as 0.40 vol% of MWCNTs but leads to an increase in the maximum dc electrical conductivity of PE/MWCNT composites by two orders of magnitudes. Moreover, the association of both Ag‐NPs and carbon nanotube particles improved our composite's thermal conductivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Surfactant dispersed multi-walled carbon nanotube/polyetherimide nanocomposite membrane

Carbon nanotube based nanocomposite membranes have been fabricated through solution casting by embedding multi-walled carbon nanotubes (MWCNTs) within polyetherimide (PEI) polymer host matrix. In order to achieve fine dispersion of nanotubes and facilitate strong interfacial adhesion with the polymer matrix, the nanotubes were first treated with surfactants of different charges, namely anionic sodium dodecyl chloride, cationic cetyl trimethyl ammonium chloride and non-ionic Triton X100, prior to the dispersion in the PEI dope solution. Dispersion of MWCNTs in N-methyl-2-pyrrolidone solvent showed that the agglomeration and entanglement of the nanotubes were greatly reduced upon the addition of Triton X100. Scanning electron microscopy and atomic force microscopy examination has evidenced the compatibility of Triton X100 dispersed MWCNTs with the polymer matrix in which a promising dispersion and adhesion has been observed at the MWCNT-PEI interface. The increase in both thermal stability and mechanical strength of the resulting Triton X100 dispersed MWCNT/PEI nanocomposite indicated the improved interaction between MWCNTs and PEI. This study demonstrated the role of Triton X100 in facilitating the synergetic effects of MWCNTs and PEI where the resulting composite membrane is anticipated to have potential application in membrane based gas separation.     

TiO2/carbon nanotube hybrid nanostructures: Solvothermal synthesis and their visible light photocatalytic activity

MWCNT/TiO₂ hybrid nanostructures were prepared via solvothermal synthesis and sol-gel method with benzyl alcohol as a surfactant. As-prepared hybrid materials were characterized by X-ray diffraction, transmission electron microscopy, UV-vis diffuse reflectance spectra and X-ray photoelectron spectroscopy. The results showed that MWCNTs were uniformly decorated with anatase nanocrystals in solvothermal condition, but MWCNTs were embedded in a majority of TiO₂ nanoparticles by sol-gel method. When the weight ratio of MWCNTs to TiO₂ was 20%, MWCNT/TiO₂ hybrid nanostructures prepared by solvothermal synthesis exhibited higher visible-light-driven photocatalytic activity than that prepared by sol-gel method. Post-annealing of MWCNT/TiO₂ nanostructures at 400 °C resulted in the formation of the carbonaceous Ti-C bonds on the interface between TiO₂ and MWCNTs, which enhanced the photoabsorbance of the hybrid materials in the visible light region and improved the visible-light degradation efficiency of methylene blue.     

Melt Dispersion and Electrospinning of Non‐Functionalized Multiwalled Carbon Nanotubes in Thermoplastic Polyurethane

Nanoscale fibers with embedded, aligned, and percolated non‐functionalized multiwalled carbon nanotubes (MWCNTs) were fabricated through electrospinning dispersions based on melt‐compounded thermoplastic polyurethane/MWCNT nanocomposite, with up to 10 wt.‐% MWCNTs. Transmission electron microscopy indicated that the nanotubes were highly oriented and percolated throughout the fibers, even at high MWCNT concentrations. The coupling of efficient melt compounding with electrospinning eliminated the need for intensive surface functionalization or sonication of the MWCNTs, and the high aspect ratio as well as the electrical and mechanical properties of the nanotubes were retained. This method provides a more efficient technique to generate one‐dimensional nanofibers with aligned MWCNTs.

     

Disposable screen-printed bismuth electrode modified with multi-walled carbon nanotubes for electrochemical stripping measurements

Integrating the advantages of screen printing technology with the encouraging electroanalytical characteristic of metallic bismuth, we developed an ultrasensitive and disposable screen-printed bismuth electrode (SPBE) modified with multi-walled carbon nanotubes (MWCNTs) for electrochemical stripping measurements. Metallic bismuth powders and MWCNTs were homogeneously mixed with graphite-carbon ink to mass-prepare screen-printed bismuth electrode doped with multi-walled carbon nanotubes (SPBE/MWCNT). The electroanalytical performance of the prepared SPBE/MWCNT was intensively evaluated by measuring trace Hg(II) with square-wave anodic stripping voltammetry (SWASV). The results indicated that the SPBE modified with 2 wt% MWCNTs could offer a more sensitive response to trace Hg(II) than the bare SPBE. The stripping current obtained at SPBE/MWCNT was linear with Hg(II) concentration in the range from 0.2 to 40 μg/L (R(2) = 0.9976), with a detection limit of 0.09 μg/L (S/N = 3) under 180 s accumulation. The proposed "mercury-free" electrode, with extremely simple preparation and ultrahigh sensitivity, holds wide application prospects in both environmental and industrial monitoring.     

Matrix‐polymer‐functionalized multiwalled carbon nanotubes as a highly efficient toughening agent for matrix polymers

Matrix‐polymer‐functionalized multiwalled carbon nanotubes (MWCNTs) are demonstrated as a highly efficient toughening agent for matrix polymers. With poly(vinylidene fluoride) (PVDF) as the matrix polymer, the PVDF/MWCNT‐PVDF nanocomposite films show high toughness. With a small load amount of MWCNT‐PVDF (0.07 wt %), the nanocomposite film shows a yield point and a constant‐stress extension region in stress–strain tests, compared with the typical low‐extensibility feature of neat PVDF film. The PVDF/MWCNT‐PVDF‐0.7 film exhibits a 180‐fold increase of toughness and about 38‐fold increase in strain at break compared with neat PVDF film. This toughening effect is attributed to (a) homogeneous dispersion of MWCNT‐PVDF in PVDF, (b) the high efficiency of load‐transfer across MWCNT/PVDF interface, and (c) the long length of the MWCNTs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012