Evaluation of a chloramine-T-selective electrode for catalytic titration of silver and mercury(II) based on iodide-catalyzed chloramine-T reactions

Semiautomatic methods are described for the catalytic titrimetric determination of microamounts of silver and mercury(II) using a chloramine-T-selective electrode as monitor. The methods are based on the inhibitory effect of Ag(I) and Hg(II) on the iodide-catalyzed chloramine-T-arsenite and chloramine-T-H₂O₂ reactions. Microamounts of silver in the range 0.2–200 μg (1 × 10⁻⁷−1 × 10⁻⁴ M) and of mercury(II) in the range 0.1–200 μg (2.5 × 10⁻⁸−5 × 10⁻⁵ M) were determined using the chloramine-T-As(III) indicator reaction. Mercury(II) in the range 4–2000 μg (1 × 10⁻⁶−5 × 10⁻⁴ M) was also determined using the chloramine-T-H₂O₂ indicator reaction. The accuracy and precision were in the range 0.1–1%.     

白藜芦醇作辣根过氧化物酶底物的布氏杆菌抗体酶联免疫传感器研究

一种纯天然产物白藜芦醇用作辣根过氧化物酶(HRP)底物。对其化学性质的研究证实,白藜芦醇在空气中较稳定,对HRP、H2O2的电化学响应性能优于传统HRP底物,对人体无毒害。白藜芦醇在HRP催化下可被H2O2氧化成醌,产物醌在电极上于-376 mV处可被还原,其电流的大小与HRP的浓试在一定浓度范围内呈线性相关。将兔布氏杆菌抗原包埋在石墨-石蜡基质中制备了测定兔布氏杆菌抗体的电化学酶联免疫传感器,该传感器测定兔布氏杆菌抗体的线性范围为3×10-4~1.65×10-2g/L;检出限为1×10-4g/L;RSD为4.6%。本方法制备免疫传感器的电化学性能稳定,抗原活性保持良好。     

Kinetic Determination of Mercury(II) at Trace Level from Its Catalytic Effect on a Ligand Substitution Process

A catalytic kinetic method (CKM) is presented for the determination of mercury(II) based on its catalytic effect on the rate of substitution of N-methylpyrazinium ion (Mpz⁺) onto hexacyanoferrate(II). The progress of the reaction was monitored spectrophotometrically at 655 nm by registering the increase in absorbance of the product [Fe(CN)₅(Mpz]²⁻ under the reaction conditions: 5 × 10⁻³ mol L⁻¹ [Fe(CN)₆]⁴⁻), 5 × 10⁻⁵ mol L⁻¹ [Mpz⁺], T = 25.0 ± 0.1°C, pH 5.00 ± 0.02 and ionic strength, I = 0.1 mol L⁻¹ (KNO₃). Quantitative rate data at specified experimental conditions showed a linear dependence of the absorbance after fixed time A _t on the concentration of mercury(II) catalyst in the range 20.06–702.1 ng mL⁻¹. The maximum relative standard deviations and percentage errors for the determination of mercury(II) in the range of 20.06–200.6 ng mL⁻¹ were calculated to be 1.7 and 2.7% respectively. The detection limit was found to be 7.2 ng mL⁻¹ of mercury(II). Accuracy (expressed in terms of recoveries) was in the range of 98–103%. Figures of merit and interference due to many cations and anions was investigated and discussed. The applicability of the method was demonstrated by determining the mercury(II) in different synthetic samples and confirming the results using atomic absorption spectrophotometry. The proposed method allowed determination of mercury(II) in the range 20.06–702.1 ng mL⁻¹ with very good selectivity and an output of 30 samples h⁻¹.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 6, 2005, pp. 654–661.Original English Text Copyright © 2005 by Surendra Prasad.This article was submitted by the author in English.     

Kinetic spectrophotometric method for the determination of urinary cobalt based on its catalytic effect on the oxidation of -adrenaline hydrochloride by hydrogen peroxide

A catalytic for determination of nanomolar concentrations of Co(II), i.e., oxidation of -adrenaline hydrochloride with H₂O² in alkaline medium, is proposed. The reaction gives a low limit of detection of 2.5 × 10 ⁻⁹ M Co(II) in the reaction mixture, good reproducibility with a relative standard deviation (R.S.D.) of 4−5% in the Co(II) concentration range 8.0 × 10⁻⁹−8.0 × 10⁻⁸M and good selectivity. On the basis of this indicator reaction, a catalytic-spectrophotometric method for the determination of cobalt in small urine samples (5.00 ml) was elaborated. The analysis of 17 urine samples, taken from healthy persons of different ages, gave cobalt concentrations in the range 0.20–1.50 μmol 1⁻¹. The R.S.D. for ten replicate analyses of a urine sample with an average cobalt content of 0.63 μmol 1⁻¹ was 5.6%. The reliability of the method was verified by a comparative photometric method (r = 0.9755) and by a determination based on known additions of cobalt (r = 0.9894).     

Electrochemical Behavior and Determination of Uric Acid at Single-Walled Carbon Nanotube Modified Gold Electrodes

The voltammetric behavior of uric acid was studied at a single-walled carbon nanotube (SWNT) modified gold electrode. Uric acid can effectively accumulate at this electrode and produce an anodic peak at about 0.45 V (vs. SCE) in pH 5.0 sodium acetate buffer solutions (HAc-NaAc). The experimental parameters, such as solution pH, accumulation time, and amount of SWNT, were optimized for determination. Under the optimum conditions, the anodic peak current is linear to the uric acid concentration over the range of 1.0×10⁻⁷ M to 2.5×10⁻⁵ M with a correlation coefficient of 0.998. The detection limit was 5.0×10⁻⁸ M for 60 s accumulation. The electrode could be easily regenerated and exhibited good stability. A 5.0×10⁻⁶ M uric acid solution was measured ten times using the same electrode, and the relative standard deviation of the peak current was 1.3%. This method was successfully applied to the determination of uric acid in human urine samples, and the recovery was 97–99%. The feasibility for simultaneous determination of xanthine, ascorbic acid and uric acid was discussed. These species did not interfere with each other in a certain concentration range. The influence of some surfactants on the anodic peak was also examined.     

Differential pulse polarographic determination of some organotin(IV) compounds in dimethyl sulfoxide

The differential pulse polarographic behavior of two series of organotin(IV) compounds having the general formula R_xSnCl_{4 − x} (R = Me, Ph; x = 1, 2, 3, 4) has been investigated in DMSO. The peaks obtained are recommended for the trace determination of these compounds. Linear calibration curves are obtained over the concentration range 10⁻⁴ –10⁻⁶ M.     

A study on terbium sensitized chemiluminescence of ciprofloxacin and its application

A novel rapid flow injection method with chemiluminescence (CL) detection was established for the determination of ciprofloxacin (CPLX), which is an antibiotic commonly used. The method is based on CL of Ce(IV)–SO₃²⁻ sensitized by Tb³⁺–CPLX, and showed the intensive bands characteristic of Tb³⁺ (⁵D₄→⁷F₅). The optimum conditions for CL emission were investigated. The linear relationship between the relative CL intensity and the concentration of CPLX is in the range of 9.0×10⁻⁹–1.0×10⁻⁶ mol/l with a detection limit of 3.1×10⁻¹⁰ mol/l. The relative standard deviation is 2.8% (n=11) for a level of 5.0×10⁻⁸ mol/l. The method was applied to the analysis of CPLX in human serum and urine samples with satisfactory results. The possible mechanism for this sensitized CL reaction is also discussed.     

Electrocatalytic Oxidation and Direct Determination of L-Tyrosine by Square Wave Voltammetry at Multi-wall Carbon Nanotubes Modified Glassy Carbon Electrodes

The electrochemical behavior of L-tyrosine was investigated at a multi-wall carbon nanotubes modified glassy carbon electrode. L-tyrosine itself showed a poor electrochemical response at the bare glassy carbon electrode; however, a multi-wall carbon nanotubes film fabricated on the glassy carbon electrode can directly enhance the electrochemical signal of L-tyrosine when applying cyclic voltammetry and square wave stripping voltammetry without any mediator. Cyclic voltammetry was carried out to study the electrochemical oxidation mechanism of L-tyrosine, which shows a totally irreversible process and an oxidation potential of 671 mV at the modified electrode and 728 mV at the bare electrode, ΔE_p = 57 mV. The anodic peak current linearly increases with the square root of scan rate in the low range, suggesting that the oxidation of L-tyrosine on the multi-wall carbon nanotubes modified electrode is a diffusion-controlled process. The square wave stripping voltammetry currents of L-tyrosine at the multi-wall carbon nanotubes modified electrodes increased linearly with the concentration in the range of 2.0 × 10⁻⁶–5.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.0 × 10⁻⁷ mol L⁻¹. The method is simple, quick, sensitive and accurate.     

Flow injection analysis of gallic acid with inhibited electrochemiluminescence detection

A flow injection (FI)–electrochemiluminescent (ECL) method has been developed for the determination of gallic acid, based on an inhibition effect on the Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) ECL system in pH 8.0 phosphate buffer solution. The method is simple and convenient with a determination limit of 9.0×10^–9 mol/L and a dynamic concentration range of 2×10^–8–2×10^–5 mol/L. The relative standard deviation (RSD) was 1.0% for 1.0×10^–6 mol/L gallic acid (n=11). It was successfully applied to the determination of gallic acid in Chinese proprietary medicine—Jianming Yanhou Pian. The inhibition mechanism proposed for the quenching effect of the gallic acid on the Ru(bpy)₃²⁺/TPrA ECL system was the interaction of electrogenerated Ru(bpy)₃^2+* and o-benzoquinone derivative at the electrode surface. The ECL emission spectra and UV-visible absorption spectra were applied to confirm the mechanism.     

Determination of Captropril using adsorptive cathodic differential pulse stripping voltammetry with the HMDE

A voltammetric method for the determination of 3-mercapto-D-2-methylpropanoyl-L-proline, a hypotensive drug whose pharmaceutical name is Captopril (CPT), in the concentration range from 9.0×10⁻¹⁰M to 3×10⁻⁶M, is described. In this range the peak current increases linearly with drug concentration even when different collection periods are used. A self-cleaning Hanging Mercury Drop Electrode (HMDE) was used and a negative Differential Pulse potential (DP) was applied to the indicator electrode. The stripping peak of CPT splits into two peaks as soon as the concentration is increased over about 10⁻⁵M; in the oxidation DP scan, instead, this splitting is observed at a concentration of 2.0×10⁻⁴M. Some attempts were made to verify the suitability of other techniques such as Alternating Current polarography (AC) and the use of a different electrode, the Wax-Impregnated Graphite Electrode (WIGE).     

Preparation of a solid membrane lead(II) diethyldithiocarbamate electrode and its application for direct and indirect anion determination

A lead(II) selective electrode has been developed. This electrode is essentially formed by a lead wire, one end of which is coated with lead(II) diethyldithiocarbamate. The response is Nernstian for lead ions in a 10⁻¹ to 10⁻⁵M concentration range. The direct determination of this element and the indirect determination of several anions are possible.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Electroanalysis of myoglobin and hemoglobin with a boron-doped diamond electrode

The electrochemical behavior of myoglobin (Mb) and hemoglobin (Hb) was investigated with a boron-doped diamond (BDD) electrode by cyclic voltammetry. In acetate buffer solutions, the oxygen reduction at the BDD electrode showed a very high overpotential while the reduction of Mb or Hb was observed in the more positive potential region. Owing to the electrocatalytic reaction of O₂ and the participation of H⁺ following the electrochemical reduction of ferric proteins, the voltammetric responses for Mb and Hb on the BDD electrode in the negative going scans became remarkable in acidic buffer solutions in air. The peak current was linearly proportional to the concentration of Mb in the range 1×10⁻⁶–2×10⁻⁵ M or the concentration of Hb from 1×10⁻⁶ to 1×10⁻⁵ M.     

Voltammetric study of the interaction of lomefloxacin (LMF)–Mg(II) complex with DNA and its analytical application

The voltammetric behavior of the LMF-Mg(II) complex with DNA at a mercury electrode is reported for the first time. In NH₃–NH₄Cl buffer (pH=9.10), the adsorption phenomena of the LMF–Mg(II) complex were observed by linear sweep voltammetry. The mechanism of the electrode reaction was found to be a reduction of LMF in the complex, and the composition of the LMF–Mg(II) complex is 2:1. In the presence of calf thymus DNA (ctDNA), the peak current of LMF–Mg(II) complex decreased considerably, and a new well-defined adsorptive reduction peak appeared at −1.63 V (vs. SCE). The electrochemical kinetic parameters and the binding number of LMF–Mg(II) with ctDNA were also obtained. Moreover, the new peak currents of LMF–Mg(II)–DNA system increased linearly correlated to the concentration of DNA in the 4.00×10⁻⁷–2.60×10⁻⁶ g ml⁻¹ range when the concentrations of LMF–Mg(II) complex was fixed at 5.00×10⁻⁶ mol l⁻¹, with the detection limits of 2.33×10⁻⁷ g ml⁻¹. An electrostatic interaction was suggested by electrochemical method.     

3-(4-Tolylazo)phenylboronic acid as the active component of polyhydroxy compounds-selective electrodes

Ionophoric, extraction, acidic and hydrophobic properties of 3-(4-tolylazo)phenylboronic acid (TAPBA) were studied. Determined K_d value equals to 36±2, pK_a equals to 8.6±0.5. TAPBA extracts dobutamine from water into chloroform and transports it across a bulk chloroform membrane. The recovery is 83% (pH=7.5), the transport rate – (6.5±0.5)×10⁻⁷ mol/h. ¹H and ¹³C NMR data confirm the formation of an 1:1 complex between arylboronic acid and catecholamine. TAPBA was used as electrode-active component of plasticized membrane electrodes with cationic and anionic responses to catecholamines and phenolic acids, respectively. For the diethyl sebacate-plasticized membrane, a slope of electrode function to dobutamine is 56±2 mV/decade; the detection limit is 1.3×10⁻⁵ mol/l; the linear range – 5×10⁻⁵–1×10⁻² mol/l; the working pH-range – 4.8–7.6; the response time – 5–10 s. ISE gives incomplete cationic function to less lipophilic catecholamines. The membrane with cationic additive shows an anionic response to caffeic acid in wide pH range.     

Cobalt-Selective Electrode Based on Titanium Ditelluride Intercalated with Cobalt

A cobalt-selective solid-contact electrode was prepared on the basis of titanium ditelluride. The electrode exhibits the slope of the electrode function –(29 ± 1) mV/pC and provides the determination of 1 × 10^–5–1 × 10^–1 M cobalt(II) in the pH range 4.5–6.5. The electrode was used for the potentiometric indication of the titration end point in the determination of cobalt(II) in lanthanum–strontium cobaltite La_0.5Sr_0.5CoO₃. The intercalant concentration range providing optimal ion-selective properties was determined.     

Determination of Selenium(IV) by Stripping Voltammetry at a Mercury-Film Electrode

A procedure was proposed for the determination of selenium(IV) by stripping voltammetry on a mercury-film electrode at an electrolysis potential of +0.4 V versus the saturated silver–silver chloride reference electrode in a 1 M H₂SO₄ solution. The current of the cathodic peak is a linear function of the selenium(IV) concentration in the range from 5 × 10^–3 to 3 × 10^–1 mg/L (6.3 × 10^–8 to 3.8 × 10^–6 M) at a time of electrolysis of 30 s (t _el). The detection limit for selenium is 1 × 10^–4 mg/L (1.3 × 10^–9 M) at t _el = 300 s. It was shown that selenium(IV) can be determined in the presence of 10 mg/L Zn(II), 1 mg/L Cd(II), 0.5 mg/L Pb(II), and 0.2 mg/L Cu(II). A procedure for the determination of selenium in natural, mineral, and potable water was proposed.     

Polarographic behaviour and determination of azintamide

Azintamide was found to be reduced at the dropping mercury electrode over the pH range 1.8–9.4 in Britton Robinson buffers containing 20% methanol. At pH 7.42 a well defined diffusion-controlled cathodic wave was produced. The limiting current versus concentration plot was linear over the range 0.025–1.0 mM and 0.005–1.0 mM in the DC_t and DPP modes, respectively, with a lower detection limit of 1 × 10^–7 M by the latter technique. A mechanism for the electrode reaction has been proposed. The method has been applied to the determination of azintamide in tablets, and the results obtained were in agreement with those obtained by a reference method.AvH Scholar 1989–1991.     

Solid substrate-room temperature phosphorimetry for the determination of trace protein using ion association complex [Cu(BPY)2]·[(Fin)2] as a phosphorescent probe

Fluorescein (HFin) emitted strong and stable room temperature phosphorescence (RTP) on filter paper after set at 50 °C for 10 min using Li⁺ as the ion perturber. HFin existed as Fin⁻ when the pH value was in the range of 5.45–7.36. Fin⁻ could react with [Cu(BPY)₂]²⁺ (BPY: α,α-bipyridyl) to produce ion association complex [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻, which could enhance the RTP signal of Hfin. In the presence of bovine serum albumin (BSA), the –COOH group of Fin⁻ in the [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻ could react with the –NH₂ group of BSA to form the ion association complex [Cu(BPY)₂]²⁺·[(Fin-BSA)₂]²⁻, which contained –CO–NH– bond. This complex could sharply enhance the RTP signal of Hfin and the ΔI_p was directly proportional to the content of BSA. According to the facts above, a new solid substrate-room temperature phosphorimetry (SS-RTP) for the determination of trace protein had been established using the ion association complex [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻as a phosphorescent probe. This method had wide linear range (0.40 × 10⁻⁹–280 × 10⁻⁹ mg l⁻¹), high sensitivity (the detection limit (LD) was 1.4 × 10⁻¹⁰ mg l⁻¹), good precision (RSD: 3.4–4.9%) and high selectivity (the allowed concentration of coexistent ions or coexistent materials was high). It had been applied to the determination of the content of protein in 10 kinds of real samples, and the result agreed well with pyrocatechol violet-Mo (VI) method (P.V.M.M.), which indicated it had high accuracy. Meanwhile, reaction mechanism for the determination of trace protein with [Cu(BPY)₂]²⁺·[(Fin)₂]²⁻ phosphorescent probe was also discussed. The academic thought of this research could not only be used to develop many kinds of ion association complex phosphorescent probes, but also provided a new way to promote the sensitivity of SS-RTP.     

Effect of various additives on the performance of a newly developed PVC based potentiometric sensor for anionic surfactants

A new poly(vinyl chloride) PVC membrane electrode to determine monomer concentrations of dodecylbenzenesulphonate ions (DBS⁻) based on a neutral ion-pair carrier complex of dodecyltrimethylammonium–dodecylbenzenesulphonate (DTA⁺–DBS⁻), is reported here. The electrode exhibits a slope of 51.25 mV per decade for DBS⁻ ions. The DBS⁻ ion selective electrode (ISE) can determine monomer units down to concentrations as low as 3.32 × 10⁻⁴ M. The effect of three kinds of additives, i.e. alcohols, glycols and triblock polymers on the performance of the surfactant selective electrode is studied systematically. The effect of foreign anions along with primary ions on the performance of ion-selective electrode is investigated in terms of potentiometric selectivity coefficients, which were determined using the fixed interference method (FIM) at 1.0 × 10⁻² M concentration of foreign anions. The sensor responds well to the surfactant ions in the presence of additives at lower concentration. The Gibbs free energy of micelle formation (ΔG_m) of sodium dodecylbenzenesulphonate (SDBS) in the presence of various additives is calculated and found to vary differently with respect to the increase in the amount of additives. The sensor worked in the acidic pH range with a short response time of 30 s. The lifetime of the sensor is more than three months. The sensor was further used to determine the amount of DBS⁻ in local detergents. This method of determining anionic surfactants was found to be quite accurate when compared with classical methods.