NiY分子筛表面酸性影响其选择性吸附脱硫性能的机理研究

采用原位红外光谱技术,以噻吩、环己烯和苯为模型探针分子,分别考察单一烃分子在NiY分子筛上的吸附与反应行为以及噻吩与烯烃、芳烃间的竞争吸附和催化反应行为。单一探针分子吸附研究发现,NiY分子筛中与Ni物种相关的Lewis(L)酸位是噻吩的选择性吸附活性位;噻吩和环己烯在NiY分子筛中Brnsted(B)酸位上发生的质子化和低聚反应明显弱于HY分子筛。双探针分子竞争吸附研究发现,环己烯二聚体在NiY中强B酸位上的强化学吸附与噻吩存在显著的竞争吸附行为。另外,苯和噻吩在NiY上的竞争吸附现象在373K时明显减弱。由此,在选择性吸附脱硫过程中,减少吸附剂表面B酸中心可降低烯烃对噻吩的竞争吸附,另外适当提高吸附体系的温度可以有效避免芳烃对噻吩的竞争吸附。     

Effect of microwave pretreatment of coal for improvement of rheological characteristics of coal-water slurries

Indian high-ash coal contains alpha-silica components of the mineral matter. When coal is transported in the form of a slurry, alpha-silica adds to the settling properties of coal and enhances erosion of pipelines. As such any technique that will contribute to changing the characteristics of mineral matter by selective demineralization is bound to supplement the knowledge of coal slurries in the science of rheology. One such method is the use of a novel microwave technology, which changes the alpha-silica to less harmful beta-silica. Thus microwave-treated coal slurry facilitates enhanced flow characteristics and abates the erosion problem in pipeline transport as well as in coal-slurry injection furnaces. This paper reports on the rheological study of closely sized coal particles of medium-volatile, low-ash, low-moisture cleans and high-ash rejects with and without microwave treatment. Viscosity of suspensions of microwave-treated coal was found to be less than that of untreated coal, in the case of both cleans and rejects. Microwave pretreatment thus reduces the viscosity and the pumping cost and opens a new outlook for pipeline transport. An attempt has been made to quantify the improvement of rheological characteristics due to microwave pretreatment.     

Study of Self-Ignition of PVC

The self-ignition of rigid PVC has been studied under static and dynamic conditions. Only a high-temperature boundary has been found, and the self-ignition temperature in air at atmospheric pressure lies between 555 and 560°C. The effect of preliminary HC1 evolution has been investigated, and it is shown that the more the HC1 evolution, the higher the self-ignition limit. It has been impossible to make polyacetylene ignite spontaneously in the presence of HC1 in oxygen up to 900° C. This is attributed to a special role of HC1 in combustion of PVC. The rate of HC1 release was measured by a potentiometric method, and the overall activation energy of the process was found to be 9.4 kcal/mole. This low value seems to be due to the presence of oxygen. Chromatographic analysis showed CH4 and CO to be the major gaseous products of oxidation of PVC in this parametric zone.     

Prediction of latent heat of vaporization of multicomponent mixtures

A very simple method has been developed for predicting the differential latent heat of vaporization involved in vapor-liquid equilibria of multicomponent mixtures. The technique uses the UNIFAC method for predicting activity coefficients.In order to establish this method, 88 binary systems and 13 ternary systems, both nonazeotropic and azeotropic, were tested successfully. On the basis of the 101 systems investigated, the mean overall deviation between the observed and predicted values was found to be 4.6%. Despite the fact that the majority of the systems tested were azeotropic, a consequence of the small amount of data available for the differential heats of nonazeotropic systems, the method proposed is equally applicable to nonazeotropic systems.For azeotropic mixtures, it is possible to predict the latent heat (integral or differential) by means of an analytical equation which involves only the parameters of Antoine's equation, with a mean overall deviation of 6.1%.From the differential heats obtained by the proposed method, it is possible to calculate integral heats by applying equations derived here which relate these quantities.     

Regularity of conductivity of concentrated aqueous solutions of strong electrolytes

Conductivity of concentrated aqueous solutions of strong electrolytes is analyzed in a wide range of temperatures and concentrations. The highest conductivity of solutions at a given temperature and the concentration corresponding to the highest conductivity are used as the generalizing parameters. It is shown that in the temperature range from 0 to 100°C and the concentration range from 0.1 to 12 M, the values of reduced conductivity (the ratio between the conductivity and its maximum value at a given temperature) for KOH aqueous solution fall on a common curve, if the reduced concentration (the ratio between the concentration of solution and the concentration corresponding to the highest conductivity) is used as the argument. The reduced conductivities of strong acids, bases, and salts of some I-I, I-II, II-I, III-I, and II-II electrolytes fall on the same curve.     

Quantitative evaluation of the mechanism of electroreduction of benzoyl cyanides

The mechanism of reduction of benzoyl cyanide, 6, p-methoxybenzoyl cyanide, 7, and p-chlorobenzoyl cyanide, 8, has been studied in acetonitrile (6 and 7), N,N-dimethylformamide (6), and acetonitrile containing water (all three compounds). The reaction proceeds by initial reduction to form the anion radical followed by dimerization to produce an intermediate dianion, the dianion of the dicyanohydrin of benzil. The latter loses cyanide to give the anion of the monocyanohydrin of benzil, which undergoes two parallel reactions: expulsion of cyanide to give the corresponding benzil and rearrangement to the monoanion of mandelonitrile benzoate. The addition of water brings about an increase in the dimerization rate constant and an associated increase in the amount of benzil that is produced. The standard potentials for the initial reduction step have been evaluated, and their dependence on the substituent is discussed. The dimerization rate constants have also been evaluated.     

Formation of ring-shaped deposits as a result of evaporating droplets of dispersions of silver nanoparticles and study of their fine structure

Scanning electron microscopy is employed to study ring-shaped deposits formed at different time moments of evaporating droplets of silver colloidal solutions on a glass substrate. It is shown that, in addition to an external fringe, several rings are formed at intermediate stages of evaporation; these rings are, in the course of time, transformed into one dense fringe and a transition zone adjacent to its internal side. The time dependences of the height and width of the fringe are determined. It is established that an increase in the width and height of the fringe is due to the transfer of silver nanoparticles to this region, which play a key role in imparting specific structural organization to the fringe. It is noted that the height of the formed fringe may be qualitatively determined by energy dispersive X-ray microanalysis.     

Influence of Apoptin on Up-regulation of the Expression of Bad and Bax

The chicken anemia virus protein, apoptin, which manifests selectivity and specificity to tumor cells, induces a p53-independent and Bcl-2-insensitive type of apoptosis in various human tumor cells. In this study, the apoptin gene was cloned from the total DNA of chicken anemia virus, and the recombinant vector was constructed. We used oligonucleotide microarray to study the changes of four genes, including Bcl-2, Bcl-xL, Bad and Bax. The post-transfection with the recombinant was also studied. The pro-apoptotic genes(Bad and Bax) and anti-apoptosis genes(Bcl-2 and Bcl-xL) were up-regulated in contrast to the controls. According to the published data, either Bcl-2 or Bcl-xL can form non-functional heterodimers by Bad and Bax binding together, resulting in blocking partly the release of cytochrome c from mitochondria. However, apoptosis could be inhibited by neither the endogenous Bcl-xL nor Bcl-2 over-expression. The experiments show that the apoptin-induced apoptotic pathway is related to the up-regulation of Bad and Bax. Bad was up-regulated by apoptin; then this up-regulated product of Bad was in favor of displacing Bax from binding to Bcl-xL or Bcl-2. Consequently. Bax exerted a pro-apoptotic dysfunction to mitochondria, thereby inducing the release of cytochrome c. Finally, apoptin induced the apoptosis of HHCC cells. These results indicate that the oligonucleotide microarray can reveal the genes related to the apoptosis induced by apoptin in HHCC cells.     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Study of the solid-state hydrolysis of chitosan in presence of HCl

Chemical depolymerization of chitosan was obtained in the solid state by means of gaseous HCl. This new method allowed us to simultaneously form the hydrochloric salt and saturate the hydration water with acid. The depolymerization was carried out by keeping the product at a given temperature for the desired time. The measurements of the molecular weight distributions demonstrated the ability to control the reaction and produce oligomers with chosen dimensions. This solid-state hydrolysis favors the presence of a four-fold distribution that can be related to the original morphology and crystallinity of the initial material. The effects of the hydrolysis on the crystallinity, the crystalline structure, and the supramolecular order of the obtained chitosans were also studied. Finally, the washing of the hydrolyzed products in concentrated alkaline or acidic media allowed us to eliminate the lowest DPs and thus to narrow the molecular weight distribution. In this case, the crystallinity was also increased up to values beyond 70%. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3181–3191, 1997     

聚丙烯酰胺胶状杂质的形成因为

在聚丙烯酰胺(PAM)配制现场发现过滤器滤袋内存在大量黑色和黄色且有刺鼻腐臭气味的胶状条形物;这类杂质造成过滤装置严重堵塞和设备腐蚀.鉴于此,从细菌和无机离子含量两方面着手分析了聚丙烯酰胺胶状条形杂质的形成因为.结果表明:由于细菌和金属离子Fe3+含量的增加,PAM的侧酰胺基降解成羧基;而含大量金属离子的PAM溶液经缠...     

Effects of micelle properties on the conformation of oligocholates and importance of rigidity of foldamers

The conformation of a cholate hexamer with a clicked tether in between two tricholate units and pyrene groups at the chain ends was studied by fluorescence spectroscopy. In contrast to the parent cholate hexamer that folded in all micelles investigated, the folding of the clicked hexamer was highly dependent on the type of surfactant used to solubilize the compound. The clicked oligocholate folded in the Brij 35 micelle, possibly due to the latter's small size and strong internal hydrophobicity. The oligocholate formed intermolecular aggregates in SDS solutions below the CMC of the surfactant. The aggregates were dissociated by the SDS micelles but the individual oligocholate stayed unfolded. In Triton X-100 and sodium cholate solutions, the aggregated, unfolded, and folded oligocholates coexisted and gradual unfolding occurred with an increasing concentration of the surfactant. The conformation of the clicked oligocholate was sensitive to the nonideal mixing of ionic/nonionic micelles and to the unconventional aggregation of sodium cholate.     

两种含杂环的氨基萘醌化合物的合成

以2,3-二氯-1,4-萘醌为主要原料,分别与吗啡啉和糠胺在一定条件下反应生成2种含杂环的氨基萘醌类化合物。2,3-二氯-1,4-萘醌与吗啡啉及2,3-二氯-1,4-萘醌与糠胺物质的量比均为1∶2,反应温度为60℃,溶剂为乙醇。2,3-二氯-1,4-萘醌与吗啡啉反应时间为1 h,产物2-氯-3-吗啡啉基萘-1,4-二酮(a)收率为93.5%;2,3-二氯-1,4-萘醌与糠胺反应时间为4 h,产物N~2,N~3-二(2-呋喃甲基)-1,4-二((2-呋喃甲基)亚胺)-1,4-二氢化萘-2,3-二氯化铵(d)收率为46.7%。对产物进行IR、Uv、MS和H-NMR等分析表征。     

Method of rapid assessment of photocatalytic activities of self-cleaning films

An ink, comprising the redox dye resazurin (Rz) and the sacrificial electron donor glycerol, is shown to be capable of the rapid assessment of the photocatalytic activities of self-cleaning films. In the key initial stage of photocatalysis the ink changes from blue to pink. Prolonged irradiation bleaches the ink and eventually mineralizes it. The kinetics of the initial photoinduced color change is studied as a function of UV irradiance, [glycerol], [Rz], and temperature. The results reveal an apparent approximate quantum yield of 3.5 x 10(-3) and an initial rate, r(i), which increases with [glycerol] and decreases with [Rz]. It is proposed that the reduction of Rz, dispersed throughout the thick (ca. 590 nm) indicator film, may take place either via the diffusion of the dye molecules in the ink film to the surface of the underlying semiconductor layer and their subsequent reaction with photogenerated electrons and/or via the diffusion of alpha-hydroxyalkyl radicals, produced by the oxidation of the glycerol by photogenerated holes, or hydroxy radicals, away from the surface of the semiconductor into the ink film and their subsequent reaction with the dye molecules therein. The decrease in r(i) with [Rz] appears to be due to dimer formation, with the latter impeding the reduction process. The activation energy for the initial color-change process is low, ca. 9.1 +/- 0.1 kJ mol(-1) and not unlike many other photocatalytic processes. The initial rate of dye reduction appears to be directly related to the rate of destruction of stearic acid. The ink can be applied by spin-coating, stamping, or writing, using a felt-tip pen. The efficacy of such an ink for assessing the photocatalytic activity of any photocatalytic film, including those employed on commercial self-cleaning glasses, tiles, and paving stones, is discussed briefly.     

Precision of Flash Pyrolysis-GC-MS Analysis: Experimental Evaluation of the Sources of Variability

The present study was carried out to evaluate the precision and to identify significant sources of variability in flash pyrolysis-GC-MS experiments. The analysis of variance has been applied to the example of polyethylene pyrolysis to estimate the impact of several controlled factors: sample handling, flash pyrolysis filament ageing and calibration. It was demonstrated that to get the best precision in experimental results, it is recommended to set the operator to reduce the impact of sample handling procedure and the filament to avoid variability due to changes in filament characteristics. In comparison, filament ageing and filament calibration are shown to influence in a limited extent the experimental results.     

Determination of shifts by means of the absolute area of the difference spectrum: cases of non-rigorous application of the theory

The method of determination of spectral shifts by use of the absolute area of the difference spectrum, previously developed in several papers, holds rigorously when the bands to be compared either have same profiles or are both symmetrical. It often happens in practice that none of these conditions is fulfilled and the concept itself of spectral shift is then questionable. However, it is possible to define in any case quantities, which, in the rigorous cases of definition of the spectral shift, are equal to each other and to the spectral shift. These quantities are the shift between the maximum intensity of the bands, the distance between vertical lines sharing the area of the bands into two equal parts, the displacement which must be given to one of the bands to reach the minimum of the absolute area of the difference spectrum. They are determined for a series of couples of model profiles, one of them being more and more dissymmetrical. Their values are compared with the approximate spectral shifts given by the application of the absolute area method. It is shown that up to relatively important dissimilarity of the profiles, the values of all these quantities are very close and may be taken as the spectral shift. Moreover, an extrapolation method giving the shift between the maximum intensities of dissimilar and dissymmetrical bands is given.     

Investigation of MM-PBSA rescoring of docking poses

Target-based virtual screening is increasingly used to generate leads for targets for which high quality three-dimensional (3D) structures are available. To allow large molecular databases to be screened rapidly, a tiered scoring scheme is often employed whereby a simple scoring function is used as a fast filter of the entire database and a more rigorous and time-consuming scoring function is used to rescore the top hits to produce the final list of ranked compounds. Molecular mechanics Poisson-Boltzmann surface area (MM-PBSA) approaches are currently thought to be quite effective at incorporating implicit solvation into the estimation of ligand binding free energies. In this paper, the ability of a high-throughput MM-PBSA rescoring function to discriminate between correct and incorrect docking poses is investigated in detail. Various initial scoring functions are used to generate docked poses for a subset of the CCDC/Astex test set and to dock one set of actives/inactives from the DUD data set. The effectiveness of each of these initial scoring functions is discussed. Overall, the ability of the MM-PBSA rescoring function to (i) regenerate the set of X-ray complexes when docking the bound conformation of the ligand, (ii) regenerate the X-ray complexes when docking conformationally expanded databases for each ligand which include "conformation decoys" of the ligand, and (iii) enrich known actives in a virtual screen for the mineralocorticoid receptor in the presence of "ligand decoys" is assessed. While a pharmacophore-based molecular docking approach, PhDock, is used to carry out the docking, the results are expected to be general to use with any docking method.     

Quantum-chemical investigation of the mechanism of the sulfonation of pyrrole

A detailed quantum-chemical study of the sulfonation of pyrrole with regard to the effect of the solvent (the model of overlapping spheres) on the energy characteristics of the formation of the σ-complexes produced during attack on the α-and β-positions of the heterocycle and their possible transformation paths was made by density functional theory [the B3LYP/6-31G(d) method]. The possibility of mutual transformations between the isomeric σ-complexes by α/β-migration of the SO₃ is examined. The formation of pyrrolesulfonic acids was studied for the case of the intramolecular rearrangement of the complexes. Comparison of the activation energies shows that in contrast to the gas-phase reaction the formation of the β-sulfonic acid is preferred in methylene chloride: the solvation energy of the α-isomer of the σ-complex is higher than the energy for the transition state of its rearrangement and its product, α-pyrrolesulfonic acid, leading to an increase in the kinetic barrier and to a decrease of the energy gain on the path to the formation of the latter. The opposite variation of the energy characteristics on the path to the β-isomer with regard to solvation leads to agreement between the calculated data and the experimentally observed preferred formation of the β-pyrrolesulfonic acid. Dedicated to Mikhail Grigor’evich Voronkov. __________ Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 11, pp. 1647–1654, November, 2006.