Electrostatic spray deposition of Gd0.1Ce0.9O1.95 and La0.9Sr0.1Ga0.8Mg0.2O2.87 thin films

The deposition of gadolinia-doped ceria (CGO, Gd_0.1Ce_0.9O_1.95) and LaGaO₃-based perovskite oxides (LSGM, La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.87) thin films on a stainless steel substrate was studied using the electrostatic spray deposition (EDS) technique. The effect of process conditions, such as deposition temperature, deposition time and liquid flow rate, on the surface morphology and microstructure of thin films was examined with scanning electron microscopy (SEM) and powder X-ray diffraction (XRD). The deposited CGO films with a highly porous and three-dimensional interconnected structure were obtained at a liquid flow rate of 0.5 ml/h, a deposition temperature of 503 K and a deposition time ranging from 0.5 to 1 h. On the other hand, the deposited LSGM thin films with porous microstructure were also obtained at the deposition time of 1 h, the deposition temperature of 533 K and the liquid flow rate of 0.5 ml/h. The deposited CGO and LSGM thin films were amorphous at the used deposition temperature. Subsequently, the samples were annealed at 1173 K for 2 h and the desired crystal structures were obtained. The chemical analysis of the thin films was investigated by energy dispersive X-ray (EDX) analysis. The observed chemical compositions of the samples were in a fair agreement with those of the starting solutions.     

Effect of deposition temperature on orientation and electrical properties of (K0.5Na0.5)NbO3 thin films by pulsed laser deposition

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) thin films have been prepared on Pt/TiO₂/SiO₂/Si substrates by pulsed laser deposition process. The structures, crystal orientations and electrical properties of thin films have been investigated as a function of deposition temperature from 680 °C to 760 °C. It is found that the deposition temperature plays an important role in the structures, crystal orientations and electrical properties of thin films. The crystallization of thin films improves with increasing deposition temperature. The thin film deposited at 760 °C exhibits strong (0 0 1) preferential orientation, large dielectric constant of 930 and the remnant polarization of 8.54 μC/cm².     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Structural, electrical, and optical properties of ZnInO alloy thin films

Indium zinc oxide (IZO) thin films with different percentages of In content (In/[In+Zn]) are synthesized on glass substrates by magnetron sputtering, and the structural, electrical and optical properties of IZO thin films deposited at different In₂O₃ target powers are investigated. IZO thin films grown at different In₂O₃ target sputtering powers show evident morphological variation and different grain sizes. As the In₂O₃ sputtering power rises, the grain size becomes larger and electrical mobility increases. The film grown with an In₂O₃ target power of 100 W displays the highest electrical mobility of 13.5 cm·V^-1·s^-1 and the lowest resistivity of 2.4 × 10^-3 Ω·cm. The average optical transmittance of the IZO thin film in the visible region reaches 80% and the band gap broadens with the increase of In₂O₃ target power, which is attributed to the increase in carrier concentration and is in accordance with Burstein-Moss shift theory.     

Growth and characterization of Y2O3 thin films

Y₂O₃ thin films were grown on silicon (1 0 0) substrates by pulsed-laser deposition at different substrate temperatures and O₂ pressures. The structure and composition of films are studied by using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Y₂O₃ thin films deposited in vacuum strongly oriented their [1 1 1] axis of the cubic structure and the film quality depended on the substrate temperature. The magnitude of O₂ pressure obviously influences the film structure and quality. Due to the silicon diffusion and interface reaction during the deposition, yttrium silicate and SiO₂ were formed. The strong relationship between composition and growth condition was discussed.     

Electrical properties of La2O3 thin films grown on TiN/Si substrates via atomic layer deposition

The electrical as well as the structural properties of La₂O₃ thin films on TiN substrates were investigated. Amorphous stoichiometric La₂O₃ thin films were grown at 300 °C via atomic layer deposition technique by using lanthanum 2,2,6,6-tetramethyl-3,5-heptanedione [La(TMHD)₃] and H₂O as precursors. Post-annealing of the grown film induced dramatic changes in structural and the electrical properties. Crystalline phases of the La₂O₃ film emerged with the increase of the post-annealing temperature. Metal-insulator-metal (MIM) capacitor was fabricated to measure the electrical properties of the grown film. The dielectric constant of the La₂O₃ thin films increased with annealing temperature to reach the value of 17.3 at 500 °C. The leakage current density of the film post-annealed at 400 °C was estimated to be 2.78 × 10⁻¹⁰ and 2.1 × 10⁻⁸ A/cm² at ±1 V, respectively.     

Investigation on FR(LT)–FR(HT) phase transition and pyroelectric properties of pulsed laser deposited Pb(Zr0.93Ti0.07)O3 thin films

The preparation process, crystallinity and electrical properties of pulse laser deposited Pb(Zr_xTi_1−x)O₃ (PZT) thin films were investigated in this paper. PZT (x = 0.93) thin film samples deposited at different substrate temperatures were prepared. Si (1 1 0) was the substrate; Ag and YBCO were the top electrode and the bottom electrode respectively. The bottom electrode YBCO was deposited on the Si substrate by pulsed laser deposition (PLD), and then PZT was epitaxially deposited on YBCO also by PLD. After annealing, the top electrode Ag was prepared on PZT by thermal evaporation, and then the Ag/PZT/YBCO/Si structured thin films were obtained. The XRD and the analysis of their electrical characters showed that, when the substrate temperature was elevated from 600 °C to 800 °C, the crystallinity and electrical properties of PZT thin films became better and better, and the F_R(LT)–F_R(HT) phase transition of PZT (x = 0.93) thin films occurred at 62 °C. The PZT film deposited at 800 °C had the best pyroelectric properties, and when the F_R(LT)–F_R(HT) phase transition of this film occurred, the peak value of pyroelectric coefficient (p) was obtained, with a value of 1.96 × 10⁻⁶ C/(cm² K). The PZT film deposited at 800 °C had the highest remnant polarization (P_r) and the lowest coercive field (E_c), with the values of 34.3 μC/cm² and 41.7 kV/cm respectively.     

Pulsed laser deposition of NdNiO3 thin films

We report the structural and transport properties of NdNiO₃ thin films prepared via pulsed laser deposition over various substrates. The films were well textured and c-axis oriented with good crystalline properties. The electrical resistivity of the films undergoes a metal-insulator transition, depending on the deposition process. Well-defined first order metal-insulator phase transition (T_MI) was observed in the best quality films without high pressure processing. Various growth conditions such as substrate temperature, oxygen pressure and thickness were varied to see their influence on T_MI. Deposition temperature was found to have a great impact on the electrical and structural properties of these films. Further the films deposited on LaAlO₃ substrate were found to be highly oriented with uniform grain size as observed from X-ray diffraction and atomic force microscopy, whereas those on Si substrate were polycrystalline, dense and randomly oriented.     

Optical and electrical properties of Y2O3 thin films prepared by ion beam assisted deposition

Y₂O₃ thin films were deposited by ion beam assisted deposition (IBAD) and the effects of fabrication parameters such as substrate temperature and ion energy on the structure, optical and electrical properties of the films were investigated. The results show that the deposited Y₂O₃ films had less optical absorption, larger refractive index, and better film crystallinity with the increase of substrate temperature or ion energy. The as-deposited Y₂O₃ films without ion-beam bombardment had larger relative dielectric constant (?_r) and the ?_r decreased with time even over by 40%, while the ?_r of films prepared with high ion energy had less changes, only less than 3%. Also, with the increase of ion energy, the electrical breakdown strength and the figure of merit increased.     

Formation of highly textured (1 1 1) Bi2O3 films by anodization of electrodeposited bismuth films

Highly textured bismuth oxide (Bi₂O₃) thin films have been prepared using anodic oxidation of electrodeposited bismuth films onto stainless steel substrates. The Bi₂O₃ films were uniform and adherent to substrate. The Bi₂O₃ films were characterized for their structural and electrical properties by means of X-ray diffraction (XRD), electrical resistivity and dielectric measurement techniques. The X-ray diffraction pattern showed that Bi₂O₃ films are highly textured along (1 1 1) plane. The room temperature electrical resistivity of the Bi₂O₃ films was 10⁵ Ω cm. Dielectric measurement revealed normal oxide behavior with frequency.     

Effect of process parameters on surface morphology and characterization of PE-ALD SnO2 thin films for gas sensing

Tin dioxide (SnO₂) thin films were deposited by plasma enhanced-atomic layer deposition (PE-ALD) on Si(1 0 0) substrate using dibutyl tin diacetate (DBTA) ((CH₃CO₂)₂Sn[(CH₂)₃-CH₃]₂) as precursor. The process parameters were optimized as a function of substrate temperature, source temperature and purging time. It is observed that the surface phenomenon of the thin films was changed with film thickness. Atomic force microscopy (AFM) images and X-ray diffraction (XRD) pattern were used to observe the texture and crystallanity of the films. The films deposited for 100, 200 and 400 cycles were characterized by XPS to determine the chemical bonding properties. XPS results reveal that the surface dominant oxygen species for 100, 200 and 400 cycles deposited films are O₂⁻, O⁻ and O²⁻, respectively. The 200 cycles film has exhibited highest concentration of oxygen (O⁻) species before and after annealing. Conductivity studies revel that this film has best adsorption strength to the oxygen ions forming on the surface. The sensor with 200 cycles SnO₂ thin film has shown highest sensitivity to CO gas than other films. A correlation between the characteristics of Sn3d_5/2 and O1s XPS spectra before and after annealing and the electrical behavior of the SnO₂ thin films is established.     

High-density plasma etching of indium-zinc oxide films in Ar/Cl2 and Ar/CH4/H2 chemistries

The dry etching characteristics of transparent and conductive indium-zinc oxide (IZO) films have been investigated using an inductively coupled high-density plasma. While the Cl₂-based plasma mixture showed little enhancement over physical sputtering in a pure argon atmosphere, the CH₄/H₂/Ar chemistry produced an increase of the IZO etch rate. On the other hand, the surface morphology of IZO films after etching in Ar and Ar/Cl₂ discharges is smooth, whereas that after etching in CH₄/H₂/Ar presents particle-like features resulting from the preferential desorption of In- and O-containing products. Etching in CH₄/H₂/Ar also produces formation of a Zn-rich surface layer, whose thickness (∼40 nm) is well-above the expected range of incident ions in the material (∼1 nm). Such alteration of the IZO layer after etching in CH₄/H₂/Ar plasmas is expected to have a significant impact on the transparent electrode properties in optoelectronic device fabrication.     

Growth mechanism and optoelectronic properties of nanocrystalline In2O3 films prepared by chemical spray pyrolysis of metal-organic precursor

Thin films of indium oxide, In₂O₃, were deposited by chemical spray pyrolysis technique, using aqueous alcoholic solutions of indium acetylacetonate (In-acac) precursor, on glass substrates kept at temperatures between 300 and 500 °C. The structural, optical, and electrical properties have been investigated as a function of deposition temperature, precursor concentration, carrier gas pressure, and substrate-to-nozzle distance. X-ray diffraction studies showed that the formation of nanocrystalline In₂O₃ films is preferentially oriented along (2 2 2) plane. The surface morphological modifications with substrate temperature were observed using scanning electron and atomic force microscopic studies. Optical transmittance behavior of the films in the visible and IR region was strongly affected by the deposition parameters. The optical band gap values observed are between 3.53 and 3.68 eV. The long wavelength limit of refractive index is 1.83. The Hall mobility is found to vary from 23 to 37 cm²/V s and carrier density is found nearly constant at about 10²⁰ cm⁻³.     

Optical and electrical properties of p-type transparent conducting CuAlO2 thin film synthesized by reactive radio frequency magnetron sputtering technique

Thin films of p-type transparent conducting CuAlO₂ have been synthesized through reactive radio frequency magnetron sputtering on silicon and glass substrates at substrate temperature 300°C. Reactive sputtering of a target fabricated from Cu and Al powder (1:1.5) was performed in Ar+O₂ atmosphere. The deposition parameters were optimized to obtain phase pure, good quality CuAlO₂ thin films. The films were characterized by studying their structural, morphological, optical and electrical properties.     

Effect of oxygen pressure on structure and properties of Bi1.5Zn1.0Nb1.5O7 pyrochlore thin films prepared by pulsed laser deposition

The Bi₂O₃-ZnO-Nb₂O₅ (BZN) cubic pyrochlore thin films were prepared on Pt/TiO₂/SiO₂/Si(1 0 0) substrates by using pulsed laser deposition process. The oxygen pressure was varied in the range of 5-50 Pa to investigate its effect on the structure and dielectric properties of BZN thin films. It is found that oxygen pressure during deposition plays an important role on structure and other properties of BZN films. The BZN films deposited at temperature of 650 °C and at O₂ pressure of 5 Pa have an amorphous BZN and Nb₂O₅ phases but exhibits a cubic pyrochlore structure with a preferential (2 2 2) orientation when the oxygen pressure increases to 10 Pa. Dielectric constant and loss tangent of the films deposited at 10 Pa are 185 and 0.0008 at 10 kHz, respectively. The dielectric tunability is about 10% at a dc bias field of 0.9 MV/cm.     

Multilayer Bi1.5Zn1.0Nb1.5O7/Ba0.6Sr0.4TiO3/Bi1.5Zn1.0Nb1.5O7 thin films for tunable microwave applications

Bi_1.5Zn_1.0Nb_1.5O₇/Ba_0.6Sr_0.4TiO₃/Bi_1.5Zn_1.0Nb_1.5O₇ tunable multilayer thin film has been fabricated by pulsed laser ablation and characterized. Phase composition and microstructure of multilayer films were characterized by X-ray diffraction, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The film has very smooth surface with RMS roughness of 1.5-2 nm and grain size of 100-150 nm. Total film thickness has been measure to be 375 nm. The BZN thin films at 300 K, on Pt(1 1 1)/SiO₂/Si substrate showed zero-field dielectric constant of 105 and dielectric loss tangent of 0.002 at frequency of 0.1 MHz. Thin films annealed at 700 °C shows the dielectric tunability of 18% with biasing field 500 kV/cm at 0.1 MHz. The multilayer thin film shows nonferroelectric behavior at room temperature. The good physical and electrical properties of multilayer thin films make them promising candidate for tunable microwave device applications.     

Synthesis and materials properties of transparent conducting In2O3 films prepared by sol-gel-spin coating technique

Transparent conducting indium oxide (In₂O₃) thin films have been prepared on glass substrates by the simple sol-gel-spin coating technique. These films have been characterized by X-ray diffraction, resistivity and Hall effect measurements, optical transmission, scanning electron microscopy and atomic force microscopy for their structural, electrical, optical and morphological properties. The influence of spin parameters, number of coating, process temperature on the quality of In₂O₃ films are studied. In the operating range of deposition, 400-475 °C, all the films showed predominant (2 2 2) orientation. Films deposited at optimum process conditions exhibited a resistivity of 2×10⁻² Ω cm along with the average transmittance of about 80% in the visible spectral range (400-700 nm).     

EFFECT OF ZnFe22O4 DOPING ON THE OPTICAL PROPERTIES OF TiO2 THIN FILMS

Amorphous TiO₂ thin films and ZnFe₂O₄ doped TiO₂ composite films were deposited by radio frequency magnetron sputtering. The effect of ZnFe₂O₄ doping on the optical properties of TiO₂ thin films was reported. Our results show that the absorption edge of TiO₂ thin films and composite films exhibits a blue shift with decreasing annealing temperature. The absorption edge of composite films has moved to visible spectrum range, and a very large red shift occurs in comparison with TiO₂ thin film. An enhanced photoluminescence in ZnFe₂O₄ doped anatase TiO₂ thin film at room temperature.     

Columnar-grown porous films of lithium manganese oxide spinel (LiMn2O4) prepared by ultrasonic spray deposition

Using LiNO₃ and Mn(Ac)₂ as raw materials, ultrasonic spray deposition (USD) technique was used to fabricate LiMn₂O₄ films on platinum substrate at different substrate temperatures from 310 to 390 °C. The prepared thick films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Electrochemical performance of the USD-derived films was also evaluated with LiMn₂O₄/Li cells. It is found that all of the LiMn₂O₄ films are porous and composed of orderly oriented columnar particles. The substrate temperature affects the fine microstructure of the columnar particles. The film prepared at 360 °C substrate temperature give rise to best electrochemical behavior.     

Growth of ZnO thin films on c-plane Al2O3 by molecular beam epitaxy using ozone as an oxygen source

The growth of c-axis oriented ZnO thin films on c-plane Al₂O₃ via molecular beam epitaxy (MBE) using dilute ozone (O₃) as an oxygen source was investigated. Four-circle X-ray diffraction (XRD) indicates that films grown at 350 °C are epitaxial with respect to the substrate, but with a broad in-plane and out-of-plane mosaic. The films were highly conductive and n-type. Epitaxial film growth required relatively high Zn flux and O₃/O₂ pressure. The growth rate decreased rapidly as growth temperature was increased above 350 °C. The drop in growth rate with temperature reflects the low sticking coefficient of Zn at moderately high temperatures and limited ozone flux for the oxidation of the Zn metal. Characterization of the films included atomic force microscopy (AFM), X-ray diffraction, photoluminescence, and Hall measurements. These results show that molecular beam epitaxy of ZnO using ozone is rate limited by the ozone flux for growth temperatures above 350 °C.