Heat transfer characteristics of decaying swirl flow through a circular tube with co/counter dual twisted-tape swirl generators

The influence of co/counter dual-twisted tapes (CoT/CT) on heat transfer rate in a circular tube has been investigated experimentally. In the experiment, the dual-twisted tapes are placed at the entry of the test tube in two arrangements: (1) each of dual twisted tape was twisted in the same direction that can produce co-swirl flow at the entry and (2) each of dual twisted tape was twisted in the opposite direction that can produce counter-swirl flow. Dual tapes were twisted in three different twist ratios (y/w = 3, 4, and 5) for generating different swirl intensities at the entry of the test section while the single twisted tape (ST) was also the test for comparison. The aim at using the dual twisted tapes is to create co/counter-rotating swirl flows having a significant influence on the flow turbulence intensity at the entry section leading to higher heat transfer enhancement. Average Nusselt numbers of CoT/CT are determined and also compared with those obtained from other similar cases, i.e., ST. The experimental results on the heat transfer rates indicated that the tubes with the dual twisted tapes (CoT/CT) are higher than those with the single tape at the entry section (x/D = 0 to 10). The heat transfer rates at longer distance became lower due to high interaction of each swirl. In addition, the mean Nusselt number and friction factor for the swirl generator created by the CT is nearly similar to CoT results.     

Simulation of turbulent non-isothermal polydisperse bubbly flow behind a sudden tube expansion

The results of numerical simulation of the structure of non-isothermal polydisperse bubbly turbulent flow and heat transfer behind a sudden tube expansion are presented. The study was carried out at a change in the initial diameter of the air bubbles within d _m1 = 1–5 mm and their volumetric void fraction β = 0–10 %. Small bubbles are available in almost the entire cross section of the tube, while the large bubbles pass mainly through the flow core. An increase in the size of dispersed phase causes the growth of turbulence in the liquid phase due to flow turbulization, when there is a separated flow of liquid past the large bubbles. Adding the air bubbles causes a significant reduction in the length of the separation zone and heat transfer enhancement, and these effects increase with increasing bubble size and their gas volumetric flow rate ratio.     

MHD mixed convection flow and heat transfer in a porous medium

The effects of a steady two-dimensional laminar MHD mixed convection flow and heat transfer against a heated vertical semi-infinite permeable surface in a porous medium are discussed. The coupled nonlinear partial differential equations describing the conservation of mass, momentum, and energy are solved by a perturbation technique. The results are presented to illustrate the influence of Hartmann number (M), Prandtl number (Pr), permeability parameter (K _p ), suction/blowing parameter (f _w ), heat generation/absorption coefficient (?), and mixed convection or buoyancy parameter (γ). The effects of different parameters on the velocity and temperature as well as the skin friction and wall heat transfer are discussed with the help of figures.     

Thermal Entanglement Between Atoms in the Four-Cavity Linear Chain Coupled by Single-Mode Fibers

Natural thermal entanglement between atoms of a linear arranged four coupled cavities system is studied. The results show that there is no thermal pairwise entanglement between atoms if atom-field interaction strength f or fiber-cavity coupling constant J equals to zero, both f and J can induce thermal pairwise entanglement in a certain range. Numerical simulations show that the nearest neighbor concurrence C_AB is always greater than alternate concurrence C_AC in the same condition. In addition, the effect of temperature T on the entanglement of alternate qubits is much stronger than the nearest neighbor qubits.     

Laminar free convection heat transfer between vertical isothermal plates

The paper represents results on numerical investigation of flow and heat transfer between two isothermal vertical plates under laminar natural convection. A system of complete Navier–Stokes equations is solved for a two-dimensional gas flow between the plates along with additional rectangular regions (connected to inlet and outlet sections), whose characteristic sizes are much greater than the spacing between the plates. The calculations were performed over very wide ranges of Rayleigh number Ra = 10 ÷ 10⁵ and a relative channel length AR = L/w = 1 ÷ 500. The influence of the input parameters on the gas-dynamic and thermal structure of thermogravitational convection, the local and mean heat transfer, and also the gas flow rate between the plates (convective draft. We determined sizes of the regions and regime parameters when the local heat flux on the walls tends to zero due to the gas temperature approach to the surface temperature. It is shown that the mean heat transfer decreases as the relative channel length AR grows, whereas the integral gas flow rate (convective draft) and Reynolds number in the channel Re = 2wUm/ν increase. The use of a modified Rayleigh number Ra* = Ra · (w/L) (Elenbaas number) leads to generalization of calculation data on mean heat transfer. These data are in good agreement with the correlations for heat transfer [1, 2] and gas flow rate [3]. The reasons of variation of the data in the range of low Rayleigh numbers are discussed in detail.     

Experimental evaluation of friction factor and heat transfer enhancement of twisted tape inserts using TiO<Subscript>2</Subscript>–water nanofluids

This paper studies the experimental evaluation of TiO₂ nanofluids in enhancing the heat transfer rate and friction factor on a micro-finned tube fitted with twisted tape inserts. Results show that the enhancement in heat transfer and pumping power completely depends on the concentration ratio of nanoparticles, pitch ratio and the type of pitch. Comparisons were made with the previous study with different operating parameters such as twist ratio and twist type. Viscosity of nanofluid increases with an increase in the concentration, which leads to increased pressure drop and pumping power. For the Reynolds number (Re = 4000), the maximum performance ratio was found as 2.1, 2, for concentration of 0.1 and 0.05, respectively. The addition of microfin arrangement inside the circular tube enhanced the performance ratio with minimum concentration of TiO₂ nanofluid.     

Twisted optical fibers sustaining propagation of optical vortices

The mode structure (the orbital number l = 1) of a few-mode weakly guiding optical fiber with high linear birefringence and a regular twist of its anisotropy axes is investigated. It is shown that, for certain values of twist pitch, the modes with l = 1 are almost pure linearly polarized optical vortices in the local coordinate system associated with the anisotropy axes. The range of values of twist pitch in which twisted fibers sustain propagation of linearly polarized optical vortices is determined numerically.     

Effect of Hall current and chemical reaction on MHD flow along a fluctuating porous flat plate with internal heat absorption/generation

Effect of Hall current on the unsteady free convection flow of a viscous incompressible and electrically conducting fluid past a fluctuating porous flat plate with internal heat absorption/generation in the presence of foreign gasses (such as H₂, CO₂, H₂O, NH₃) was investigated. The results are discussed with the effect of the parameters m, the Hall current, Mt, the hydromagnetic parameter, G _r the Grashoff number for heat transfer, G _c , the Grashoff number for mass transfer, S, the internal heat absorption/generation parameter, α, the transpiration parameter, S _c , the Schmidt parameter, and K _c the chemical reaction parameter for Prandtl number P _r = 0.71, which represents air. Further, the present study accounts for the 1st order chemical reaction affecting the flow characteristics. The governing equations are solved in closed form applying Hh _n (x) function. The effects of pertinent parameters characterizing the flow field are discussed with the help of graphs and tables. The important observation of the present study is that heat generation/absorption modifies the flow of current simultaneously to a magnetic force and thermal bouncy force. Heat generation combined with blowing leads to a sharp fall of temperature.     

Structural Transitions in Elemental Tin at Ultra High Pressures up to 230 GPa

The quantum heat generation, interaction force, and friction torque for two rotating spherical nanoparticles with the radius R are calculated. In contrast to a static case where an upper bound in the radiative heat transfer between two particles exists, the quantum heat generation for two rotating particles diverges at distances between particles d < d ₀ = R(3/ε″(ω₀))^1/3 (where ε″(ω₀) is the imaginary part of the dielectric function for the material of a particle at the resonance frequency ω₀), when the rotation frequency coincides with poles in the excitation generation rate at Ω = 2ω₀. These poles are due to the anomalous Doppler effect and the mutual polarization of particles and exist even in the presence of dissipation in particles. The anomalous heat generation is associated with the conversion of mechanical rotation energy into heat mediated by quantum friction. Similar singularities also exist for the interaction force and friction torque. The results can be of significant importance for biomedical applications.     

Effect of thermal inhomogeneity on the performance of a Brownian heat engine

We explore the effect of thermal inhomogeneity on the performance of a Brownian heat engine by considering exactly solvable models. We first consider a Brownian heat engine which is modeled as a Brownian particle in a ratchet potential moving through a highly viscous medium driven by the thermal kick it receives from a linearly decreasing background temperature. We show that even though the energy transfer due to kinetic energy is neglected, Carnot efficiency cannot be achieved at quasistatic limit. At quasistatic limit, the efficiency for such a Brownian heat engine approaches the efficiency of endoreversible engine η = 1 ? √T _c /T _h [F.L. Curzon, B. Ahlborn, Am. J. Phys. 43, 22 (1975)]. Moreover, the dependence of the current, the efficiency and the coefficient of performance of the refrigerator on the model parameters is also explored via Brownian dynamic simulations and analytically. We show that such a Brownian heat engine has a higher performance when acting as a refrigerator than when operating as a device subjected to a piecewise constant temperature [M. Asfaw, M. Bekele, Eur. Phys. J. B 38, 457 (2004), M. Asfaw, M. Bekele, Physica A 384, 346 (2007)]. Furthermore, for a Brownian heat engine driven by a piecewise constant temperature, we show that systematic removal of the inhomogeneous medium leads to a homogeneous medium with a uniform temperature where the effect of temperature inhomogeneity is replaced by an effective load.     

Effect of V cut in perforated twisted tape insert on heat transfer and fluid flow behavior of tube flow: An experimental study

ABSTRACT

Present study investigates the heat transfer and friction characteristics of heat exchanger tube fitted with perforated twisted tape (PTT) insert having V cuts. A copper tube of 1 m length and 0.032 m inner diameter is used as test section to collect the experimental data by varying the twist ratio of PTT from 2 to 6 for the Reynolds number range of 2,700–23,400. V cuts are introduced in the PTT and the V-cut relative pitch ratio is varied from 1 to 2. The maximum thermo-hydraulic performance parameter is found to be 1.58.     

Thermal effect analysis on crosstalk and performance of optoelectronic transmitter modules for optical interconnects

This paper presents thermal analysis on crosstalk and performance of optoelectronic transmitter modules and also demonstrates the thermal analysis for efficient heat dissipation for the transmitter modules. The thermal crosstalk model for analysis is based on interconnects parameters for vertically stacked and horizontally packaged optoelectronic transmitter modules. While the analytical expression is used to estimate the thermal critical frequency, f _{crit_th} , above which signals become severely deteriorated, a Teflon-based thermal printed circuit board (PCB) has been designed for packaging the optoelectronic transmitter modules to ensure efficient heat dissipation. The thermal and performance analysis of the packaged modules show that the chips operate at temperatures below the f _{crit_th} , which is apt for reliable data and signal transmission.     

Structure and electrophysical properties of ferrocobaltites <Emphasis Type="Italic">Ln</Emphasis>BaFeCoO<Subscript>5 + δ</Subscript> (<Emphasis Type="Italic">Ln</Emphasis> = Tb,Dy, Ho,Y)

The ferrocobaltites LnBaFeCoO^{5 + δ} (Ln = Tb, Dy, Ho, Y) have been synthesized, and the parameters of their crystal structure have been determined. The thermal expansion, electrical resistivity ρ, and thermopower S of the synthesized compounds have been investigated in air at temperatures in the range from 300 to 1100 K. The compounds have a tetragonal structure (symmetry space group P4/mmm) with the unit cell parameters a = 3.9000 Å and c = 7.5922 Å (Ln = Tb, δ = 0.31), a = 3.8973 Å and c = 7.5679 Å (Ln = Dy, δ = 0.34), a = 3.8970 Å and c = 7.5507 Å (Ln = Ho, δ = 0.28), and a = 3.9029 Å and c = 7.5538 Å (Ln = Y, δ = 0.25). The ferrocobaltites under investigation are p-type semiconductors, and their electrical resistivity ρ and thermopower S decrease in the sequence Tb → Ho → Y → Dy (at room temperature). The linear thermal expansion coefficient of the LnBaFeCoO^{5 + δ} phases in the vicinity of the temperatures ranging from 465 to 535 K increases from (1.15?1.23) × 10^?5 to (1.73?1.93) × 10^?5 K^?1. The parameters of charge transfer in these ferrocobaltites have been determined. It has been found that an increase in the temperature leads to an increase in the excitation energy of charge carriers and a decrease in the activation energy of charge carrier transfer.     

Quantum Cherenkov radiation at the motion of a small neutral particle parallel to the surface of a transparent dielectric

Quantum Cherenkov radiation and quantum friction at the motion of a small neutral particle parallel to the surface of a transparent dielectric with the refractive index n have been studied in a fully relativistic theory. Radiation appears at velocities above the threshold value, v > v _c = c/n. The friction force in the particle–plate configuration has been derived from the friction force in the plate–plate configuration under the assumption that one of the plates is significantly decharged. A decrease in the kinetic energy of the particle near the threshold velocity is due to its radiation and near the speed of light is determined by the heat power absorbed by the particle in the rest frame. The powers of quantum and classical Cherenkov radiation can be comparable in the relativistic case.     

Low-temperature anomalies in the specific heat and thermal conductivity of MgB<Subscript>2</Subscript>

The temperature dependences of the specific heat C(T) and thermal conductivity K(T) of MgB₂ were measured at low temperatures and in the neighborhood of T _c . In addition to the well-known superconducting transition at T _c ≈40 K, this compound was found to exhibit anomalous behavior of both the specific heat and thermal conductivity at lower temperatures, T≈10–12 K. Note that the anomalous behavior of C(T) and K(T) is observed in the same temperature region where MgB₂ was found to undergo negative thermal expansion. All the observed low-temperature anomalies are assigned to the existence in MgB₂ of a second group of carriers and its transition to the superconducting state at T_c2≈10?12 K.     

Thermal Performance Evaluation of Heat Exchanger Tubes Equipped with Coupling Twisted Tapes

The present work has been conducted to investigate the effect of coupling twisted tapes on heat transfer enhancement in a heat exchanger. The effects of (1) twisted tape orientation (co-coupling twisted tapes or counter-coupling twisted tapes), (2) width ratio, and (3) twist ratio were also examined. Results of coupling twisted tapes were also compared to those of a typical twisted tape. Experimental results showed that the use of counter-coupling twisted tapes resulted in higher heat transfer, friction loss, and thermal performance factor than that of co-coupling twisted tapes and typical twisted tapes. Thermal performance factor increased as twist ratio and Reynolds number decreased while width ratio increased.     

Heat Transfer in a Tube Fitted with Vertical and Horizontal Wing-Cut Twisted Tapes

This article reports an experimental investigation on the heat transfer, friction factor, and thermal enhancement factor of a tube equipped with vertical wing-cut twisted tapes, horizontal wing-cut twisted tapes, and plain twisted tapes with twist ratios of y = 2.0, 4.4, and 6.0. The obtained results reveal that the heat transfer rate, friction factor, and thermal enhancement factor in the tube equipped with horizontal wing-cut twisted tapes are significantly higher than those in the tube fitted with vertical wing-cut twisted tapes, plain twisted tapes, and a plain tube. An empirical correlation is subsequently derived from the experimental results.     

Influence of Morphological Defects on Thermophysical Properties of γ-Gd<Subscript>2</Subscript>S<Subscript>3</Subscript>

The temperature dependences of the heat capacity (C _p ) and the thermal conductivity (κ) in the temperature range from 300 to 773 K of polycrystalline gadolinium sulfide samples (γ-GdS _y ) with the deviation of the composition from the integer stoichiometric were studied. It was found that the thermal conductivity of gadolinium sulfides decreases monotonically and reaches 0.74 W/(m K) at T = 773 K for the composition y = 1.479, which is much lower than for the known single-crystal samples. The influence of morphological defects (boundaries of crystallites and dislocations) on the intensity of scattering of phonons is studied. It has been established that ceramic samples of gadolinium sulphides have a large heat capacity and a lower thermal conductivity, in comparison with monocrystalline samples of the same composition.     

Helical Quantum States in a Strongly Frustrated Two-Dimensional Magnet

Thermodynamic properties of the J₁–J₂–J₃ quantum Heisenberg model are investigated on a square lattice with spin S = 1/2. The calculation of spin–spin correlators, spin excitation spectra, susceptibility, and heat capacity within a spherically symmetric approach shows that the third exchange J₃ may qualitatively change the properties of the system. Along with standard short-range order (antiferromagnetic, ferromagnetic, and stripe) structures, various quantum helices arise. In particular, these structures may be isotropic with a local minimum of the spectrum along a circle in the Brillouin zone. The character of these states represents both ferromagnetic and antiferromagnetic “twisted” quantum spin ordering. Moreover, a range of parameters is determined in which heat capacity exhibits two-peak temperature behavior.     

Thermophysical study of structural phase transitions in Na<Subscript>0.95</Subscript>Li<Subscript>0.05</Subscript>NbO<Subscript>3</Subscript> solid solution

Temperature dependences of specific heat C_p(T) and coefficient of thermal expansion ;(T) for Na_0.95Li_0.05NbO₃ sodium-lithium niobate ceramic samples are investigated in the temperature range of 100–800 K. The C_p(T) and α(T) anomalies at T₃ = 310 ± 3 K, T₂ = 630 ± 8 K, and T₁ = 710 ± 10 K are observed, which correspond to the sequence of phase transitions N ? Q ? S(R) ? T2(S). The effect of heat treatment of the samples on the sequence of structural distortions was established. It is demonstrated that annealing of the samples at 603 K leads to splitting of the anomaly corresponding to the phase transition Q → R/S in two anomalies. After sample heating to 800 K, the only anomaly is observed in both the C_p(T) and ;(T) dependence. Possible mechanisms of the observed phenomena are discussed.