离子印迹法制备对铜离子(Ⅱ)选择性吸附的碳基材料

通过钨离子印记方法,合成了对铜离子有高选择性吸附性能的碳基材料。 在四乙烯五胺(TEPA)、钨酸铵和葡萄糖摩尔比为1:1:5条件下,经水热法合成的碳基吸附材料能有效地吸附铜离子,对铜离子吸附的最佳pH=5。 在Cd²⁺、Co²⁺、Cu²⁺、Ni²⁺和Zn²⁺摩尔浓度相近体系中,离子印记碳基吸附材料对铜离子的吸附率高达97.2%,而对Cd²⁺、Co²⁺、Ni²⁺、Zn²⁺吸附率分别为20.1%、9.63%、20.3%、13.3%,表明这种离子印记碳基吸附材料对Cu²⁺具有非常优异的选择吸附能力。     

金属螯合亲和膜吸附分离与纯化溶菌酶的研究(Ⅱ)──不同金属螯合亲和膜对溶菌酶的吸附性能

采用低温氧或氨等离子体法改性聚丙烯微孔膜,基于等离子体改性膜的活化、偶联及螯合过程的机理,制备了Fe³⁺,Ni²⁺,Cu²⁺和Zn²⁺等金属离子螯合亲和膜,并用于溶菌酶的吸-脱附实验.实验结果表明,Ni²⁺和Cu²⁺离子螯合亲和膜对溶菌酶具有较高的吸附量,螯合过程中采用氯化物盐溶液制得的膜对溶菌酶吸附量比采用硫酸盐溶液制得的膜的吸附量高.两种膜的重复吸-脱附性能相近,而Fe³⁺螯合亲和膜基本上不能用于重复吸-脱附实验.采用补充金属螯合离子,能部分恢复亲和膜对溶菌酶的吸附量,是实现亲和膜重复使用的有效方法.     

pH法测定若干金属离子与天门冬酰胺络合反应的热力学参数

本文在不同温度和离子强度为0.1的条件下,以pH电位法分别测定了Co²⁺、Ni²⁺、Cu²⁺、Zn²⁺、Cd²⁺与天门冬酰胺形成1:2络合物时的平衡常数。在所有测定的温度范围内,吉氏自由能变化的递变顺序为Cu²⁺2+2+2+2+。以温度系数法计算了有关络合反应的焓和墙的变化,并据此对反应的动力问题进行了讨论。     

天然高分子壳聚糖作为吸附剂的吸附特性研究

甲壳素经化学改性制得的壳聚糖吸附Cu²⁺、Ni²⁺、Zn²⁺、Ca²⁺、Rb⁺、Cs⁺、Cd²⁺、Pb²⁺等离子的研究已有报道^[1],但吸附Pd²⁺等贵金属离子的研究尚不多见.本文报道了壳聚糖及其交联产物的造粒方法,并测定了该糖吸附Hg²⁺、Cu²⁺、Ag⁺、Pd²⁺等离子的特性.结果表明,化学交联后的颗粒(作吸附剂)在酸性条件下仍保持相当好的刚性,对Pd²⁺离子的吸附容量较大,在Pd²⁺、Cu²⁺共存时可选择性吸附Pd²⁺.     

油页岩飞灰对重金属离子的吸附动力学及热力学

采用批式振荡吸附法研究了燃油页岩电厂循环流化床锅炉飞灰对重金属离子Pb²+、Cu²+、Zn²+、Cd²+的吸附动力学及吸附热力学特性,并提出了吸附机理。结果表明,油页岩飞灰对Pb²+、Cu²+、Zn²+、Cd²+的吸附平衡数据符合Langmuir和Freundlich吸附等温方程,但Freundlich方程能够更好地描述吸附等温线。在油页岩飞灰对重金属离子吸附的初始阶段,拉格朗日准一级动力学方程、准二级动力学方程、Elovich方程、粒子内扩散模型均能很好地反映吸附模式,而整个吸附过程则遵循二级反应动力学方程,其吸附过程是液膜扩散和粒子内扩散共同作用的结果。油页岩飞灰对Pb²+、Cu²+、Zn²+、Cd²+的吸附是吸热反应。     

新型含氮、硫纤维素螯合树脂的合成及其吸附性能

将稻壳纤维素的氯化产物(CDC)分别与水合肼、乙二胺、二乙烯三胺、三乙烯四胺、丁二胺和己二胺反应,合成了6种含氮纤维素螯合树脂(ADC-1～ADC-6);在碱性条件下用环硫氯丙烷交联ADC合成了6种新型含氮、硫纤维素螯合树脂(TADC-1～TADC-6),研究了合成条件和ADC,TADC树脂对金属离子的吸附性能.结果表明,ADC树脂对Cu²⁺,Cr³⁺,Ni²⁺,Hg²⁺,Zn²⁺等离子有较好的吸附性,对Hg²⁺吸附容量可达0.5mmol/g左右;TADC树脂对Ag⁺,Cu²⁺,Hg²⁺等离子有较好的吸附性,对Hg²⁺和Ag⁺吸附容量可达1.1mmol/g和1.9mmol/g左右;强酸性条件下,ADC和TADC树脂的吸附容量都降低,它们对金属离子的吸附顺序分别为Hg²⁺>Cu²⁺>Ni²⁺和Ag⁺>Hg²⁺>Cu²⁺,树脂用10%的氨水解吸附可重复使用.     

PANI-SnP复合膜电极在镍镉废水中电控离子交换性能

采用滴涂法在铂基底制备了电活性聚苯胺-磷酸锡(PANI-SnP)复合膜电极,考察了该电极在Ni²⁺、Cd²⁺溶液的电控离子交换性能. 用傅立叶变换红外光谱和扫描电镜分析观察复合膜的组成及表面形貌;在0.1 mol·L^-1 Ni(NO₃)₂、Cd(NO₃)₂溶液,通过循环伏安法比较了PANI膜、SnP膜及PANI-SnP复合膜电极的电化学性能,并结合电化学石英晶体微天平技术重点考察了PANI-SnP复合膜的离子交换机制;同时,通过循环伏安法调控复合膜电极的氧化还原电位,结合X射线能谱和X射线光电子能谱分别测定了其氧化和还原状态的元素组成. 结果表明,PANI-SnP复合膜电极在Ni²⁺、Cd²⁺溶液均有良好的氧化还原电活性和可逆离子交换性能,其Cd²⁺离子选择性优于Ni²⁺离子,通过电控离子交换可使Cd²⁺离子从镍镉废水高效分离.     

A highly selective chemosensor for copper ion based on ICT fluorescence

Simple structural compounds 1 to 3 were synthesized.The presence of Cu²⁺ resulted in the fluorescence and absorption spectra change of 1 and 2,which indicated that 1 and 2 showed a highly selective response to Cu²⁺ over other metal ions.However,3 showed no selectivity for metal ions,which means that the compound could bind with several metal ions,such as,Ni²⁺,Zn²⁺,Cd²⁺.Hg²⁺, Pb²⁺,Fe³⁺,Mg²⁺,Ca²⁺,and Co²⁺,except Cu²⁺ and Ag⁺.The different spectral responses were attributed to the difference in binding sites for 1 and 3.     

新型络合吸附剂的研究(Ⅱ)——铜离子模板高分子多乙烯多胺络合吸附剂的合成和特性

以金属Cu(Ⅱ)离子为模板,合成了高分子多乙烯多胺络合吸附剂,研究了它们对重金属离子(Cu²⁺,Ni²⁺,Co²⁺,Zn²⁺)的吸附特性。发现这类吸附剂具有高吸附容量和优良的吸附选择性。     

N,N-二甲基吡啶苯甲醛缩对二甲氨基苯甲酰腙的合成及对Cu2+的选择性识别

设计合成了可用于识别铜离子的化合物N,N-二甲基吡啶苯甲醛缩对二甲氨基苯甲酰腙(1), 通过¹H NMR, ¹³C NMR和MS等对其结构进行了表征; 采用荧光光谱和吸收光谱法研究了化合物1与金属离子间的相互作用. 结果表明, 化合物1对Cu²⁺ 呈现良好的选择性, Cu²⁺ 的加入使化合物1的荧光强度增强12.5倍, 加入其它金属离子如Fe³⁺, Zn²⁺, Pb²⁺, Hg²⁺, Cd²⁺, Co²⁺, Ni²⁺, Li⁺, K⁺, Ca²⁺, Mg²⁺ 和 Ag⁺, 仅引起化合物1荧光强度的微降. 采用双倒数线性回归拟合法计算可知, 化合物1与Cu²⁺ 形成了1: 1型强发光配合物, 结合常数为2.0×10⁷ L/mol.     

金属离子对彩色成像过程的影响

通过测量和计算彩色单层片中成色剂的照相活性、偶合效率以及漂白前银密度等参数,研究了在分散四当量成色剂青(Ⅰ)时掺入金属离子Mg²⁺、Zn²⁺、Fe³⁺和Cu²⁺对彩色青单层片的成像过程中各个化学反应的影响。本实验的结果表明,成色剂中加入的金属离子Cu²⁺和Fe³⁺对成像过程的初始反应中的Ag影像形成产生不利的影响,但它们能促进偶合过程中青(Ⅰ)与显影剂氧化产物作用所生成的隐色体转变成染料的速率。Mg²⁺和Zn²⁺的加入主要是对偶合过程中青(Ⅰ)的偶合效率产生不利的影响。上述原因的综合影响,最终降低了彩色单层片的感光度。     

沉淀基离子选择电极对干扰离子的动力学响应研究

用活度阶梯法研究了AgI,AgBr,CuS,PbS和CdS电极对干扰离子的动力学响应.溶液中含一定浓度主要离子时上述电极对某些干扰离子响应非单一突跃型瞬时信号;溶液中不含主要离子时,除了AgBr电极响应Cl^-外,其它都响应单一瞬时信号.离子交换产物的溶解度越小,离子的水合焓差越小,瞬时信号峰高度越大.离子水合焓差对瞬时信号峰高度的影响说明,试液高速喷向电极表面时由于扩散层厚度很薄,电极对干扰离子响应瞬时信号的峰电位不决定于离子扩散速度,而决定于离子交换速度.除CuS电极外,根据其它电极非单一突跃型瞬时信号所测定的平衡电位选择性系数K_xy^e与相应化合物溶度积比值是一致的.     

Coordination properties of 1-allyl-2-methylimidazole relative to some metal ions in the solid state and aqueous solution

Cobalt(II) and copper(II) complexes with 1-allyl-2-methylimidazole (L), of general formula [ML₂(NO₃)₂], have been prepared in the solid state. The compounds were characterised by structural, spectroscopic and magnetic measurements. The metal ions in both six coordinate complexes are surrounded by two nitrogen atoms of the imidazole rings and four oxygen atoms of the chelating nitrato group (the CoN₂O₄ and CuN₂O₄ chromophores). The structure of both chromophores is described by a very distorted tetragonal bipyramid. The formation of successive complexes of the azole with Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺ and Cd²⁺ in aqueous solution was followed potentiometrically. An irregularity in the K_n constants of successive Co²⁺ and Zn²⁺ complexes suggests a change in the coordination sphere of the central ions from octahedral to tetrahedral. With the Co²⁺–1-allyl-2-methylimidazole system, the change has been proven by inspection of the visible absorption spectra.     

Bioremediation Process and Bioremoval Mechanism of Heavy Metal Ions inAcidic Mine Drainage

Acidic mine drainage(AMD) containing acidity and a broad range of heavy metal ions is classified as hazardous, and must be properly treated. The removal mechanism of heavy metal ions in acidic mine drainage contai- ning Cu²⁺, Fe²⁺, and Zn²⁺ with biological method was studied here. Using 20 mmol/L ethanol as carbon source, Desulfovibrio marrakechensis,one of sulfate reducing bacteria(SRB) species, grew best at 35 ℃ and pH=6.72 with concentrations of 10, 55 and 32 mg/L for Cu²⁺, Fe²⁺ and Zn²⁺, respectively. The removal efficiency for each ion mentioned above was 99.99%, 87.64% and 99.88%, respectively. The mineralogy and surface chemistry of precipitates were studied by means of energy dispersive spectrometer(EDS), X-ray photoelectron spectroscopy(XPS), X-ray diffraction(XRD) combined with control tests. The experimental results demonstrate that the removal mechanism of heavy metal ions by Desulfovibrio marrakechensis is comprehensive function of chemical precipitation, adsorption and bioprecipitation. The biogenic iron sulfide solid was characterized as greigite(Fe₃S₄), while the zinc sulfide solid was characterized as sphalerite(ZnS).     

Selective transport of silver ions through bulk liquid membrane using Victoria blue as carrier

Transport of Ag⁺ as Ag(CN)₂⁻ ions through a bulk liquid membrane is reported. The bulk liquid membrane used is a solution of Victoria blue (VB) in chloroform. The effects of pH of the source phase, cyanide concentration in the source phase, sodium hydroxide in the receiving phase, and VB concentration in the organic phase on the efficiency of the transport system were studied. The above system has a high selectivity for Ag⁺ and can selectively and efficiently transport Ag(CN)₂⁻ ion from aqueous solutions containing other cations such as alkali and alkaline earths, Zn²⁺, Pd²⁺, Cu²⁺, Cd²⁺,Hg²⁺, Co²⁺, Fe²⁺, Pb²⁺, Ni²⁺, and Al³⁺.     

第四周期过渡金属钼磷三元杂多化合物的氧化还原性质研究

研究了Keggin结构钼磷杂多化合物Na₅[PM(H₂O)Mo₁₁O₃₉]·nH₂O(M=Mn²⁺,Co²⁺,Ni²⁺,Cu²⁺,Zn²⁺在溶液中的氧化还原性质,发现环境的改变可对杂多阴离子的极谱半波电位产生影响,其影响程度的大小决定于过渡金属离子本身的性质。取代后的钼磷杂多阴离子的半波电位顺序为Ni²⁺>Co²⁺>Zn²⁺>Cu²⁺>Mn²⁺,pH值的变化影响氧化还原性质,并阐述了变价金属Cu²⁺对杂多阴离子氧化还原性质的影响.     

12-钨磷酸及其盐的酸性与催化性能的研究

红外法研究结果表明12-钨磷酸Fe³⁺、Mg²⁺和Na⁺盐都具有L酸点和B酸点。用Benesi法测得10种12-钨磷酸盐的酸强度顺序为(Al³⁺、Fe³⁺、La³⁺、Cu²⁺、Cd²⁺>Zn²⁺>(Ca²⁺、Mg²⁺>(Na⁺、Li⁺,其酸量与抗衡阳离子的离子势和电负性大体成线性关系。还看出酸量与所含结晶水量有关。催化剂的酸量与其对异丙醇脱水反应和丁烯-1异构化反应的催化活性的关系表现出不同的特征,这可用“体相型”和“表面型”催化作用的不同特点来解释。     

A Highly Selective Fluorescent Chemosensor for Cu2+

A new Zn²⁺ probe L2-Zn(L2=naphthofuran carbonylhydrazone derivant) was synthesized as a fluorescence chemosensor for Cu²⁺, by which Cu²⁺ ion could be detected with high selectivity and sensitivity in a wide pH range via a displacement “turn-off” signaling strategy. Whereas the coordination between Zn²⁺ and L2 resulted in a considerable enhancement of typical luminescence of a naphthalofuran group in complex L2-Zn, the addition of Cu²⁺ ion led to a dramatic decrease in the emission intensity of probe L2-Zn at about 503 nm(excitation at 423 nm). The competitive fluorescent experiments showed that other metal ions, such as Hg²⁺, Fe³⁺, Ag⁺, Ca²⁺, Co²⁺, Ni²⁺, Cd²⁺, Pb²⁺, Zn²⁺, Cr³⁺ and Mg²⁺ could not impact the detection of Cu²⁺. The detection limit of the novel probe L2-Zn for Cu²⁺ ion was as low as 2.3×10^-7 mol/L, which is far lower than the guideline value of 1.6×10^-5 mol/L of the United States Environmental Protection Agency.