Extremes of some foam properties and elasticity of thin foam films near the critical micelle concentration

The elasticity of open and closed thin foam films is analyzed. The elasticity modulus of a closed film is shown to be additive with respect to contributions from Gibbs elasticity and disjoining pressure. A detailed expression for the film elasticity modulus explains the pronounced maxima of foaminess and foam stability near the critical micelle concentration observed earlier in many experiments. A theory of transversal elasticity of thin foam films is formulated under conditions excluding the action of Gibbs elasticity. Near the critical micelle concentration, the theory predicts maxima of the transversal elasticity modulus and of the films thickness as functions of concentration at a given disjoining pressure. The prediction has been verified experimentally by measuring the film thickness in equilibrium foam as a function of height.     

Bovine serum albumin unfolding at the air/water interface as studied by dilational surface rheology

Measurements of the surface dilational elasticity close to equilibrium did not indicate significant distinctions in the surface conformation of different forms of bovine serum albumin (BSA) in a broad pH range. At the same time, the protein denaturation in the surface layer under the influence of guanidine hydrochloride led to strong changes in the kinetic dependencies of the dynamic surface elasticity if the denaturant concentration exceeded a critical value. It was shown that the BSA unfolding at the solution surface occurred at lower denaturant concentrations than in the bulk phase. In the former case, the unfolding resulted in the formation of loops and tails at surface pressures above 12 mN/m. The maximal values of the dynamic surface elasticity almost coincided with the corresponding data for the recently investigated solutions of β-lactoglobulin, thereby indicating a similar unfolding mechanism.     

Influence of demulsifier on interfacial film between oil and water

Demulsification of a synthetic water in oil (W/O) crude oil emulsion was studied by measuring water–oil interfacial properties such as life time and thinning rate of oil film in the presence of various demulsifiers. The results indicated that the interfacial elasticity decreased both the strength and the life time of oil film and film thickness when adding the demulsifiers. The oil film broke when film thickness came to a critical level. As for a demulsifier, the interfacial elasticity was decreased with demulsifier concentration increase, and stayed constant above a critical demulsifier concentration. The rate of dewatering is related to interfacial elasticity. When different demulsifiers were compared, the more the interfacial elasticity was lowered, the more efficient was the dewatering. The mechanism of the different types of demulsifiers was discussed based on the experimental results. The demulsifiers partially replaced the emulsifiers, which led to the interfacial elasticity decreased. The effect of chemical structure of the demulsifiers on water–oil interfacial film was studied.     

Manifestation of Gibbs Elasticity in Thin Films

The elasticity of multicomponent closed and partially open thin films is analyzed. The elastic modulus of a completely closed film is shown to be additive with respect to contributions that are due to the Gibbs elasticity and disjoining pressure. In the case of only one closed component (e.g., a surfactant), both contributions are inseparably related to each other and may be expressed one through the other. For films of surfactant solutions, the resultant expressions make it possible to explain the marked maximum (observed in many experiments) of the foaming capacity of solutions and stability of foams in the vicinity of the critical micellization concentration.     

On the Modulus of Transverse Elasticity of Thin Foam Films

The theory of transverse elasticity of thin foam films is formulated under the conditions when the action of Gibbs elasticity is excluded. The theory predicts the presence of maxima of the modulus of transverse elasticity and film thickness near the critical micellization concentration as functions of the content of surfactant at a given disjoining pressure. Theoretical conclusions are confirmed experimentally by measuring film thickness at various heights of equilibrium foam column.     

Influence of the elasticity of cellulose solutions on the dispersion of carbon black agglomerates

A counter-rotating rheo-optical tool was used to study the dispersion process of carbon black agglomerates in different suspending media, including the solutions of different types of cellulose, aqueous hydroxypropylcellulose solutions, and polyisobutylene. For each suspending fluid, the mechanism of dispersion (erosion or rupture) was identified, and the macroscopic critical shear stress necessary for dispersion was measured. Checking that the impacts of fluid infiltration and agglomerate size on the macroscopic critical shear stress for dispersion were negligible in our case, we showed that elasticity is a major factor acting on dispersion physics. At a constant viscosity, the higher the elasticity is, the more difficult dispersion is, giving higher critical shear stresses for initiating dispersion. There is a linear correlation between the suspending fluid elasticity and this critical shear stress, independent of temperature. An explication of the influence of matrix elasticity on agglomerate dispersion based on recent numerical simulation is given.     

破乳剂对油水界面膜作用机理研究

研究了破乳剂存在下油膜寿命、油膜薄化速率以及油水界面性质与破乳效果的关系.结果表明,破乳剂使油水界面弹性降低,导致油水界面强度减弱,界面膜寿命变短,界面膜厚度变薄.当膜厚度变薄到一临界值时,膜破裂,导致破乳脱水.同种破乳剂,随着其浓度的增加,界面弹性降低.当浓度超过某一值时,界面弹性值基本不变.不同种破乳剂,界面弹性降低幅度越大,其破乳效果越好.界面弹性值可以很好解释破乳剂的脱水率变化规律.     

Influence of bulk elasticity and interfacial tension on the deformation of gelled water-in-oil emulsion droplets: an AFM study

We used atomic force microscopy (AFM) to study the deformation and wetting behavior of large (50-250 microm) emulsion droplets upon mechanical loading with a colloidal glass probe. Our droplets were obtained from water-in-oil emulsions. By adding gelatin to the water prior to emulsification, also droplets with a bulk elasticity were prepared. Systematic variations of surfactant and gelatin concentrations were made, to investigate their effect on the deformation and wetting behavior of the droplets and to identify the contributions of interfacial tension, bulk elasticity, and expelled water. The AFM experiments were performed in force--distance mode and showed on approach a repulsive regime which in many cases was terminated by a jump-in of the probe. In the case of pure water (i.e. gelatin-free) droplets, the repulsive part of the curve showed a good linearity, thus allowing the extraction of an effective droplet spring constant. This quantity was found to decrease on raising the surfactant concentration from below the critical micelle concentration (cmc) to well above the cmc, and its numerical values were found to correspond remarkably well to literature values for the interfacial tension. Our findings indicate that, on gelatin increase inside the droplets, the bulk elasticity gradually becomes dominant and the droplets' stiffness does not depend anymore on surfactant concentration. Also the stability of the droplet interface against wetting, as measured by the force at which the jump-in instability occurs, was enhanced by gelatin. For gelatin concentrations of > or =15 wt %, the droplets were found to behave like purely elastic bodies. Both gelatin and surfactant contribute positively to the stability against interface breakup.     

Carboxymethylated nanofibrillated cellulose: rheological studies

The rheological properties of carboxymethylated nanofibrillated cellulose (NFC), investigated with controlled shear rate- and oscillatory measurements, are reported for the first time. It was shown that the rheological properties of the studied system are similar to those reported for other NFC systems. The carboxymethylated NFC systems showed among other things high elasticity and a shear thinning behaviour when subjected to increasing shear rates. Further, the shear viscosity and storage modulus of the system displayed power-law relations with respect to the dry content of the NFC suspension. The exponential values, 2 and 2.4 respectively, were found to be in good agreement with both theoretical predictions and published experimental work. Furthermore, it was found that the pulp consistency at which NFC is produced affects the properties of the system. The rheological studies imply that there exists a critical pulp concentration below which the efficiency of the delamination process diminishes; the same adverse effect is also observed when the critical concentration is significantly exceeded due to a lower energy input during delamination.     

疏水链长对聚氧乙烯失水山梨醇脂肪酸酯界面扩张流变性质的影响

利用悬挂滴方法研究了系列聚氧乙烯失水山梨醇脂肪酸酯(TweenX)在正癸烷-水界面的扩张流变性质. 实验结果表明, 疏水烷基链长较短的Tween20 分子在界面上吸附量较大, 分子排列更紧密, Tween40 和Tween60具有大致相同的“有效截面积”, 导致饱和吸附时界面张力(γ_cmc)比较接近. TweenX浓度大于临界胶束浓度(cmc)时, 由于Tween20 分子排列的更加紧密, 模量和弹性大于Tween40 和Tween60. 当TweenX的疏水烷基链长达到一定长度时, TweenX的界面膜性质受疏水链长的影响减弱, Tween40和Tween60的扩张参数相差不大.     

Numerical investigation of the effect of insoluble surfactants on drop deformation and breakup in simple shear flow

The effect of insoluble surfactants on drop deformation and breakup in simple shear flow is studied using a combination of a three-dimensional boundary-integral method and a finite-volume method to solve the coupled fluid dynamics and surfactant transport problem over the evolving interface. The interfacial tension depends nonlinearly on the surfactant concentration, and is described by the equation of state for the Langmuir isotherm. Results are presented over the entire range of the viscosity's ratio lambda and the surface coverage x, as well as the capillary number Ca that spans from that for small deformation to values that are beyond the critical one Ca(cr). The values of the elasticity number E, which reflects the sensitivity of the interfacial tension to the maximum surfactant concentration, are chosen in the interval 0.1 < or = E < or = 0.4 and a convection dominated regime of surfactant transport, where the influence of the surfactant on drop deformation is the most significant, is considered. For a better understanding of the processes involved, the effect of surfactants on the drop dynamics is decoupled into three surfactant related mechanisms (dilution, Marangoni stress and stretching) and their influence is separately investigated. The dependence of the critical capillary number Ca(cr)(lambda) on the surface coverage is obtained and the boundaries between different modes of breakup (tip-streaming and drop fragmentation) in the (lambda; x) plane are searched for. The numerical results indicate that at low capillary number, even with a trace amount of surfactant, the interface is immobilized, which has also been observed by previous studies. In addition, it is shown that for large Péclet numbers the use of the small deformation theory to measure the interfacial tension in the case where surfactants are present can introduce a significant error.     

聚氧乙烯醚类表面活性剂表面扩张粘弹性质研究

研究了非离子表面活性剂壬基苯酚聚氧乙烯醚NP-8, NP-10和NP-12水溶液的表面扩张粘弹性质, 考察了氧乙烯数的变化对表面吸附膜特性的影响. 研究结果表明, 三种表面活性剂的扩张弹性随着工作频率的增大而增大, 扩张粘性则在0.1~0.01 Hz范围内通过不明显的极大值; 扩张弹性和粘性随着浓度的增加在同一浓度处通过一个极大值; 氧乙烯数从8增加到12, 表面扩张弹性、粘性和相角的变化不大. 从发生在表面上和表面附近的微观弛豫过程的角度对实验结果进行了讨论.     

The interfacial dilational properties of hydrophobically modified associating polyacrylamide studied by the interfacial tension relaxation method at an oil-water interface

The interfacial dilational viscoelastic properties of hydrophobically associating block copolymer composed of acrylamide (AM) and a low amount of 2-phenoxylethyl acrylate (POEA) (<1.0 mol%) at the octane-water interfaces were studied by means of the interfacial tension relaxation method. The dependencies of interfacial dilational elasticity and viscous component on the dilational frequency were investigated. The interaction of hydrophobically associating block copolymer [P(AM/POEA)] with sodium dodecyl sulfate (SDS) has been explored. The results show that at lower frequency, the dilational elasticity for different concentration copolymer is close to zero; at higher frequency, the dilational elasticity shows no change with increased frequency; At moderate frequency (10(-3)-1 Hz), the dilational elasticity decreased with a decrease in the dilational frequency. The results show that the hydrophobic groups of [P(AM/POEA)] chains can be associated by inter- or intrachain liaisons in water solution. The dilational viscous component for P(AM/POEA) comes forth a different maximum value at different frequencies when the polymer concentration is different. It is generally believed that the dilational viscous component reflects the summation of the various microscopic relaxation processes at and near the interface and different relaxation processes have different characteristic frequencies. The spectrum of dilational viscous component may appear more than once maximum values at different frequencies. The influence of SDS on the limiting dilational elasticity and viscous component for polymer solution was elucidated. For 5000 ppm polymer solution, the limiting dilational elasticity decreased with an increase in SDS concentration. The dilational viscous component passed through a maximum value with a rise in the dilational frequency, which appeared at different frequency when SDS concentration is different; and the higher is the concentration, the lower is the dilational frequency. It can be explained that macromolecules may be substituted by SDS molecules in the interface and the interaction of molecules decrease, which makes the limiting dilational elasticity decrease. For 200 ppm polymer solution, the limiting dilational elasticity increased firstly and then decreased with SDS concentration increasing. This may be explained that the interfacial polymer concentration is so low that SDS molecules absorbed in the interface dominate dilational properties of the interfacial film even at very low SDS concentration. However, SDS molecules can gradually substitute the polymer molecules in the interface with a rise in SDS concentration, which results in the decrease in the limiting dilational elasticity.     

Numerical simulation of nanoparticle melting inside a matrix

A theoretical model is proposed for describing the melting of a metal nanoparticle embedded into a solid matrix. The model is based on a thermodynamic approach that takes into account matrix elasticity. The melting process is described for gold nanoparticles embedded in a solid matrix whose elastic modulus is varied in a wide range. Both spherical and ellipsoidal particles are considered. It is shown that particle melting temperature can be both higher and lower than the melting point of a bulk sample depending on the interaction intensity of the solid and liquid particle surfaces with the matrix. An increase in the shear modulus of the matrix causes a rise in the nanoparticle melting temperature, with the effect of the matrix elasticity becoming noticeable at some critical shear modulus. The conditions are revealed at which only a surface layer of a nanoparticle, the thickness of which depends on the particle radius and temperature, is melted.     

Effect of the addition of polyelectrolytes on monolayers of carboxybetaines

We have studied the effect of the addition of sodium poly(styrene sulfonate) polymers on the properties of monolayers formed by the adsorption of two carboxybetaines with different number of separation methylenes between their charged groups. Fluorescence and surface tension measurements indicate that above the critical aggregation concentration a surfactant-polymer complex of electrostatic origin is formed in bulk. The complexes have a negative charge that is repelled by the negative charge of the surfactant adsorbed at the interface; consequently, the monolayer seems to be exclusively formed by surfactant carboxybetaines. The high-frequency surface viscoelasticity of the monolayers was studied by surface dynamic light-scattering measurements. The behavior of the dilational elasticity and viscosity is explained by relaxation involving molecular reorientation within the adsorbed layer.     

Interaction between puroindolines and the major polar lipids of wheat seed endosperm at the air-water interface

To understand the role of the puroindolines (PIN-a and PIN-b) in the defense mechanism and stabilization of lipid films in the gas cell of bread dough, we have isolated the proteins and lipids from wheat seed endosperm and studied their interaction at the air/water interface using a Langmuir trough. The nature and shape of the pressure–area compression isotherms of the lipid monolayer in the presence of puroindolines in the subphase depended on the concentration of protein. A distinct phase separation occurred, when the concentration of protein in the subphase increased. The interfacial elasticity of the lipid monolayer in the presence of puroindolines in the subphase was higher than the pure lipid. Injection of protein beneath the preexisting lipid monolayer resulted in the increase of surface pressure due to the penetration of proteins. The extent of penetration depended on the nature of lipid head groups as well as on the initial surface pressure. The penetration of puroindolines to lipid monolayer was observed to be zero after crossing a critical initial surface pressure. The magnitude of the critical initial surface pressure for anionic lipids was significantly higher than the zwitterionic and nonionic lipids. The experimental results showed that both PIN-a and PIN-b had more affinity for anionic polar lipids than the neutral polar lipids and stabilized the lipid monolayer.     

Oscillatory shear response of moisture barrier coatings containing clay of different shape factor

Oscillatory shear rheology of barrier coatings based on dispersed styrene-butadiene latex and clay of various shape factors or aspect ratio has been explored. Barrier performance of these coatings when applied to paperboard has been assessed in terms of water vapour transmission rates and the results related to shape factor, dewatering and critical strain. It has been shown that a system based on clay with high shape factor gives a lower critical strain, dewatering and water vapour transmission rate compared with clays of lower shape factor. The dissipated energy, as calculated from an amplitude sweep, indicated no attractive interaction between clay and latex implying a critical strain that appears to be solely dependent on the shape factor at a constant volume fraction. Particle size distribution was shown to have no effect on the critical strain while coatings of high elasticity exhibited high yield strains as expected. The loss modulus demonstrated strain hardening before the elastic to viscous transition. The loss modulus peak was identified by a maximum strain which was significantly lower for a coating based on clay with a high shape factor. The characteristic elastic time was found to vary between 0.6 and 1.3s. The zero shear viscosity of barrier dispersion coatings were estimated from the characteristic elastic time and the characteristic modulus to be of the order of 25-100 Pa s.     

Dilational rheology of spread and adsorbed layers of silica nanoparticles at the liquid-gas interface

This short review is devoted to recent achievements in studies of the dilational surface rheological properties of the systems containing complexes of silica nanoparticles with conventional surfactants. It is shown that there is a surfactant concentration range where the dynamic surface elasticity reaches extremely high values up to 1000 mN/m. This result can explain the formation of very stable foams and emulsions containing nanoparticles. In some surfactant concentration ranges the adsorption layer is characterized by a non-linear response to small compressions or expansions of the liquid surface. Possible causes of this behavior and the mechanism of main relaxation processes are briefly discussed.     

Modification of epoxy polymers with epoxy thiirane derivative of benzimidazolone-2

An epoxy thiirane derivative of benzimidazolone-2 was synthesized. An addition of epoxy thiirane derivative of denzimidazolone-2 to epoxy rubber and epoxy composites was shown to increase their thermal stability, elasticity modulus, and cohesion and adhesion strengths, especially at higher test temperatures. The effect depends on the concentration of additive, hardening temperature, type of rubber, and other factors.     

Micromechanics and contact forces of colloidal aggregates in the presence of surfactants

We report measurements of the bending mechanics of colloidal aggregates consisting of poly(methyl methacrylate) (PMMA) flocculated with 250 mM MgCl2 in the presence of either pentaethylene glycol monododecyl ether (C(12)E(5)), a nonionic surfactant, or sodium dodecyl sulfate (SDS), an anionic surfactant. In the absence of surfactant, singly bonded aggregates exhibit a substantial bond rigidity, kappa(0), in the linear bending regime. With the addition of surfactant, the tangential restoring force between particles becomes weaker; aggregates exhibit nonlinear mechanics at a lower critical bending moment, M(c), and the bond rigidity decreases. The decrease in kappa(0) is related to the reduction of the surface energy of adhesion between particles, W(SL). We find that W(SL) decreases with increasing surfactant concentration below the critical micelle concentration (cmc). However, above the cmc, W(SL) remains constant within experimental error. These results confirm the relation between the bond rigidity and the surface energy of adhesion and clearly demonstrate that, on the basis of this relationship, surface-active agents provide a means of tuning the macroscopic elasticity and yield stress of colloidal gels. Last, the mechanics of the critical moment is consistent with the surfactant lowering the stress at which the contact line between the particles de-pins.