Critical effects of a spanwise surface wire on flow past a circular cylinder and the significance of the wire size and Reynolds number

An experimental study is conducted on flow past a circular cylinder fitted with a single spanwise wire on its surface. The work investigates the dependency of the critical wire locations on the wire size and Reynolds number, and examines the near wake and vortex shedding characteristics in an effort to advance the understanding of the critical wire effects beyond the existing literature. The Reynolds number is varied from 5000 to 30 000, and the wire diameter is varied from 2.9% to 5.9% of the cylinder diameter. All wires are larger than the boundary-layer thickness forming around a comparable smooth cylinder. Constant Temperature Anemometry and hydrogen bubble visualization are used as the flow diagnostic tools. The frequency and strength of the Karman instability are shown to vary with the wire location at any given Reynolds number nearly in an inverse fashion. For all the Reynolds numbers and wire sizes considered, two types of critical locations are shown to exist on the cylinder surface for the application of a wire. These locations are associated with the attenuation and amplification of the Karman instability, and in accord with the existing literature, are denoted as θ_c1 and θ_c2, respectively. The present work reveals that θ_c2 consists of a wide range of locations which remains unaffected from the wire size and Reynolds number, while θ_c1 is a relatively distinct location on the cylinder surface and depends on both the Reynolds number and wire size. For a given Reynolds number, increasing the wire size decreases θ_c1. For a given wire size, increasing the Reynolds number from 5000 to 15 000 increases θ_c1, and past 15 000, θ_c1 remains unaffected from the Reynolds number. When a wire is at θ_c1, even though, for the majority of the time the regular formation of Karman vortices ceases, the present data also reveals intermittent, short time periods where the regular shedding resumes.     

URANS vs. experiments of flow induced motions of multiple circular cylinders with passive turbulence control

Two-dimensional Unsteady Reynolds-Average Navier–Stokes equations with the Spalart–Allmaras turbulence model are used to simulate the flow induced motions of multiple circular cylinders with passive turbulence control (PTC) in steady uniform flow. Four configurations with 1, 2, 3, and 4 cylinders in tandem are simulated and studied at a series of Reynolds numbers in the range of 30 000<Re<120 000. Simulation results are verified by experimental data measured in the Marine Renewable Energy Laboratory. Good agreement was observed between the values of vorticity, amplitude ratio, and frequency ratio predicted by numerical simulations and experimental measurements. The amplitude and frequency response show the initial and upper branches in vortex induced vibration (VIV), transition from VIV to galloping, and galloping branch for all PTC-cylinders. The maximum amplitude of 2.9 diameters for the first cylinder is achieved at Re=104 356 in the numerical results. Compared with the first cylinder, the VIV initial branch starts at higher Re for the downstream cylinders due to the presence of the upstream cylinder(s). 2P and 2P+2S vortex patterns are observed at Re=62 049 and Re=90 254 for the single PTC-cylinder. Furthermore, the shed vortices of the downstream cylinders are strongly disrupted and modified by the vortices shed from the upstream one in the cases of multiple PTC-cylinders.     

Numerical solutions for impulsively started and decelerated viscous flow past a circular cylinder

A finite difference study of the unsteady two-dimensional flow past a circular cylinder has been conducted using vorticity and streamfunction as the dependent variables. The two cases considered were impulsively started and decelerated flows. The impulsively started problem was considered to validate the method and has yielded results which agree quite closely with existing results from both calculations and experiments. The decelerated flow analysis produced results which can be explained in terms of induced velocity effects from existing wake vortices for both suddenly stopped and uniformly decelerated flows.     

Scale-adaptive simulation of flow past wavy cylinders at a subcritical Reynolds number

The Xu & Yan scale-adaptive simulation (XYSAS) model is employed to simulate the flows past wavy cylinders at Reynolds number 8 × 10 3.This approach yields results in good agreement with experimental measurements.The mean flow field and near wake vortex structure are replicated and compared with that of a corresponding circular cylinder.The effects of wavelength ratios λ/D m from 3 to 7,together with the amplitude ratios a /D m of 0.091 and 0.25,are fully investigated.Owing to the wavy configuration,a maximum reduction of Strouhal number and root-meansquare (r.m.s) fluctuating lift coefficients are up to 50% and 92%,respectively,which means the vortex induced vibration (VIV) could be effectively alleviated at certain larger values of λ/D m and a /D m.Also,the drag coefficients can be reduced by 30%.It is found that the flow field presents contrary patterns with the increase of λ/D m.The free shear layer becomes much more stable and rolls up into mature vortex only further downstream when λ/D m falls in the range of 5-7.The amplitude ratio a /D m greatly changes the separation line,and subsequently influences the wake structures.     

Fully developed flow in a curved pipe of arbitrary curvature ratio

It is generally assumed in curved pipe flow analyses that the curvature ratio, δ, of the pipe is very small, in which case the flow depends on a single parameter, the Dean number. This is not the case if δ is not very small. To determine the importance of this effect we have numerically solved the full Navier-Stokes equations, in primitive variable form, for arbitrary values of δ. A factored ADI finite-difference scheme has been used, employing Chorin's artificial compressibility technique. The results show that the central-difference calculation on a staggered grid is stable, without adding artificial damping terms, due to coupling between pressure and velocity. A spatially variable time step is used with a fixed Courant number.     

Numerical investigation on flow around circular cylinders in tandem arrangement at a subcritical Reynolds number

Three-dimensional fluid computations have been performed to investigate the flows around two circular cylinders in tandem arrangements at a subcritical Reynolds number, Re=2.2×10⁴. The center-to-center space between the cylinders was varied from twice the cylinder diameter to five times that, and the flows and fluid-dynamic forces obtained from the simulations are compared with the experimental results reported in the literature. Special attention is paid to the characteristics of the vortices shed from the upstream cylinder such as the convection, the impingement onto the downstream cylinder and the interaction with the vortices from the downstream cylinder. The effects of the vortices from the upstream cylinder on the fluid-dynamic forces acting on the downstream cylinder are discussed.     

Modes of vortex formation and transition to three-dimensionality in the wake of a freely vibrating cylinder

The present work is aimed to give some insight into the relation between vortex shedding modes and transition to three-dimensionality in the wake of a freely vibrating cylinder by establishing a numerical model and analyzing the relevant results of two- and three-dimensional simulations. The compressible flow past an elastically-mounted cylinder is solved by using the immersed boundary method (IB method). The cylinder is free to vibrate in the transverse direction with zero structure damping. The response of displacement amplitude is studied with the variation of reduced velocity. Whether P+S mode exists in three-dimensional flow and the occurrence of 2P mode is caused by flow transition from two-dimensional to three-dimensional are problems of concern. Both 2P and P+S wake modes are observed in two- and three-dimensional simulations. The numerical results indicate that the flow transition from two-dimensional to three-dimensional is coupled with the cylinder vibration in the synchronization/lock-in regime. The wake formation given by three-dimensional simulations suggests that the P+S mode might exist in reality when the flow is reverted to two-dimensional by vortex induced vibration (VIV) at Re=300–350. When Reynolds number increases to 425, the wake formation undergoes transition to three-dimensionality and 2P mode is observed. The effect of mass ratio on the flow transition to three-dimensionality is studied. The relationship between wake modes and aerodynamic forces is discussed.     

Numerical investigation of steady suction control of flow around a circular cylinder

This paper numerically investigates the effectiveness of the control of steady suction on a stationary circular cylinder with several isolated suction holes on the surface at a subcritical Reynolds number. The control effectiveness as a function of the azimuthal position, spanwise spacing and suction flow rate of the suction holes on the control of the aerodynamic forces on the cylinder and the suppression of alternate vortex shedding are taken into account. The study of the azimuthal location of the suction holes indicates that azimuthal angles of θ=90° and 270°, which are close to the separation point, provide the most substantial decreases in the aerodynamic forces. When restricted to the most effective azimuthal angle, a remarkable control effectiveness can be achieved when the axial spacing between two neighboring suction holes is less than a minimum value even under a small suction momentum coefficient. However, if the axial spacing exceeds the minimum spacing, the control effectiveness will not be saturated even under a very large suction momentum coefficient. Thus, the cause of the effective aerodynamic force control is suggested to be a result of obvious three-dimensional phenomenon in the near wake, which is characterized by the generation of a convergent flow between two neighboring suction hole sections and a stronger, larger three-dimensional vortex pair adjacent to the convergent flow. It has been suggested that this strongly three-dimensional flow pattern is induced by the strong interaction between two neighboring but counter-rotating three-dimensional vortices separately produced by two neighboring suction holes. Moreover, the effects of such three-dimensional flow patterns are investigated in detail based on variations in the flow field and sectional aerodynamic forces in different cross sections. Finally, the upper limit of the axial spacing between two neighboring suction holes to form such a three-dimensional flow pattern is suggested to be between 0.75 D and 1.5 D when the suction flow rate exceeds a certain value.     

Experimental study of vortex-induced vibrations of a cylinder near a rigid plane boundary in steady flow

In this study, the vortex-induced vibrations of a cylinder near a rigid plane boundary in a steady flow are studied experimentally. The phenomenon of vortex-induced vibrations of the cylinder near the rigid plane boundary is reproduced in the flume. The vortex shedding frequency and mode are also measured by the methods of hot film velocimeter and hydrogen bubbles. A parametric study is carded out to investigate the influences of reduced velocity, gap-to-diameter ratio, stability parameter and mass ratio on the amplitude and frequency responses of the cylinder. Experimental results indicate： （1） the Strouhal number （St） is around 0.2 for the stationary cylinder near a plane boundary in the sub-criti- cal flow regime; （2） with increasing gap-to-diameter ratio （eo/D）, the amplitude ratio （A/D） gets larger but frequency ratio （f/fn） has a slight variation for the case of larger values of eo/D（eo/D 〉 0.66 in this study）; （3） there is a clear difference of amplitude and frequency responses of the cylin- derbetween the larger gap-to-diameter ratios （e0/D 〉 0.66） and the smaller ones （e0/D 〈 0.3）; （4） the vibration of the cylinder is easier to occur and the range of vibration in terms of Vr number becomes more extensive with decrease of the stability parameter, but the frequency response is affected slightly by the stability parameter; （5） with decreasing mass ratio, the width of the lock-in ranges in terms of Vr and the frequency ratio （f/fn） become larger.     

Vortex shedding and surface pressures on a square cylinder at incidence to a uniform air stream

This article describes results of experiments on vortex-shedding frequencies and surface pressures of a square cylinder at non-zero angle of incidence. The range of Reynolds numbers was 2000–21 000, but the lower range was emphasized. For Reynolds numbers greater than 5300, the Strouhal number shows a similar trend with changing angle of incidence; that is, a rapid rise in Strouhal number occurs at an angle of around 13°. The occurrence of such a jump in Strouhal number was found to be associated with onset of the flow reattachment, bringing in a strong pressure recovery on the lower side face of the cylinder. For lower Reynolds numbers Re=2000–3300, the maximum Strouhal number occurs at a relatively higher angle of 17°. Around this angle, the pressure measurements exhibit a rather weak pressure recovery, suggesting a less firm shear-layer reattachment to the side face of the cylinder. The nature of the reattaching flow was further examined by spectral analysis of the fluctuating pressure coefficients measured on the lower side face of the cylinder.     

Dependence of flow classification on the Reynolds number for a two-cylinder wake

This work aims to investigate the dependence of flow classification on the Reynolds number (Re) for the wake of two staggered cylinders. The Re examined ranges from 1.5×10³ to 2.0×10⁴. The pitch ratio, P^⁎=P/d examined is 1.2–6.0 (d is the cylinder diameter), and angle (α) is 0–90°, where P is the center-to-center spacing between two cylinders and α is the angle between the incident flow and the line through the cylinder centers. Two single hotwires were used to measure simultaneously the fluctuating streamwise velocities (u) in the vortex streets generated by the two cylinders. The power spectral density functions and the Strouhal numbers were then obtained from the u signals, based on which the flow structure pattern or mode could be determined. Over two hundred configurations of two staggered cylinders have been examined for each Re. It is found that Re has an appreciable effect on the dependence of the flow mode on P^⁎ and α. The observation is connected to the Re effect on the generic features of a two-cylinder wake such as flow separation, boundary layer thickness, gap flow deflection and vortex formation length.     

Two-dimensional unsteady laminar flow of a power law fluid across a square cylinder

The two-dimensional and unsteady free stream flow of power law fluids past a long square cylinder has been investigated numerically in the range of conditions 60≤Re≤160 and 0.5≤n≤2.0. Over this range of Reynolds numbers, the flow is periodic in time. A semi-explicit finite volume method has been used on a non-uniform collocated grid arrangement to solve the governing equations. The global quantities such as drag coefficients, Strouhal number and the detailed kinematic variables like stream function, vorticity and so on, have been obtained for the above range of conditions. While, over this range of Reynolds number, the flow is known to be periodic in time for Newtonian fluids, a pseudo-periodic flow regime displaying more than one dominant frequency in the lift is observed for shear-thinning fluids. This seems to occur at Reynolds numbers of 120 and 140 for n=0.5 and 0.6, respectively. Broadly speaking, the smaller the value of the power law index, lower is the Reynolds number of the onset of the pseudo-periodic regime. This work is concerned only with the fully periodic regime and, therefore, the range of Reynolds numbers studied varies with the value of the power law index. Not withstanding this aspect, in particular here, the effects of Reynolds number and of the power law index have been elucidated in the unsteady laminar flow regime. The leading edge separation in shear-thinning fluids produces an increase in drag values with the increasing Reynolds number, while shear-thickening fluid behaviour delays this separation and shows the lowering of the drag coefficient with the Reynolds number. Also, the preliminary results suggest the transition from the steady to unsteady flow conditions to occur at lower Reynolds numbers in shear-thinning fluids than that in Newtonian fluids.     

Numerical simulation of two-degree-of-freedom vortex-induced vibration of a circular cylinder close to a plane boundary

Two-degree-of-freedom vortex-induced vibrations (VIV) of a circular cylinder close to a plane boundary are investigated numerically. The Reynolds-Averaged Navier-Stokes (RANS) equations are solved using the Arbitrary Lagrangian Eulerian (ALE) scheme with a k-ω turbulence model closure. The numerical model is validated against experimental data of VIV of a cylinder in uniform flow and VIV of a cylinder close to a plane boundary at low mass ratios. The numerical results of the vibration mode, vibration amplitude and frequency agree well with the experimental data. VIV of a circular cylinder close to a plane boundary is simulated with a mass ratio of 2.6 and gap ratios of e/D=0.002 and 0.3 (gap ratio is defined as the ratio of gap between the cylinder and the bed (e) to cylinder diameter (D)). Simulations are carried out for reduced velocities ranging from 1 to 15 and Reynolds numbers ranging from 1000 to 15 000. It is found that vortex-induced vibrations occur even if the initial gap ratio is as small as e/D=0.002, although reported research indicated that vortex shedding behind a fixed circular cylinder is suppressed at small gap ratios (e/D<0.3 or 0.2). It was also found that vibration amplitudes are dependant on the bouncing back coefficient when the cylinder hits the plane boundary. Three vortex shedding modes are identified according to the numerical results: (i) single-vortex mode where the vortices are only shed from the top of the cylinder; (ii) vortex-shedding-after-bounce-back mode; (iii) vortex-shedding-before-bounce-back mode. It was found that the vortex shedding mode depends on the reduced velocity.     

The effect of air-water interface on the vortex shedding from a vertical circular cylinder

The flow past an interface piercing circular cylinder at the Reynolds number Re=2.7×10⁴ and the Froude numbers Fr=0.2 and 0.8 is investigated using large-eddy simulation. A Lagrangian dynamic subgrid-scale model and a level set based sharp interface method are used for the spatially filtered turbulence closure and the air-water interface treatment, respectively. The mean interface elevation and the rms of interface fluctuations from the simulation are in excellent agreement with the available experimental data. The organized periodic vortex shedding observed in the deep flow is attenuated and replaced by small-scale vortices at the interface. The streamwise vorticity and the outward transverse velocity generated near the edge of the separated region, which enforces the separated shear layers to deviate from each other and restrains their interaction, are primarily responsible for the devitalization of the periodic vortex shedding at the interface. The lateral gradient of the difference between the vertical and transverse Reynolds normal stresses, increasing with the Froude number, is the main source of the streamwise vorticity and the outward transverse velocity at the interface.     

Investigation of passive oscillations of flexible splitter plates attached to a circular cylinder

This paper presents a numerical study to address wake control of a circular cylinder subjected to two-dimensional laminar flow regime using single and multiple flexible splitter plates attached to the cylinder. Three different cases are presented in the study, covering cylinders with one, two and three horizontally attached splitter plates while the locations of the plates around the cylinders are varied. The length of the splitter plates was equal to the cylinder diameter and Reynolds number was 100. Due to the flexibility of the plates, the problem was modeled as a Fluid–Structure Interaction (FSI) problem and the commercial finite element software, Comsol Multiphysics, was utilized to solve this problem using Arbitrary Lagrangian–Eulerian (ALE) method. Vortex shedding frequency and fluid forces acting on the cylinder are investigated, along with a comprehensive parametric study to identify the optimum arrangement of the plates for maximum drag reduction and maximum vortex shedding frequency reduction. The numerical results associated to the flexible splitter plates are also compared with the corresponding rigid splitter plate cases investigated in a previous study. Moreover, the tip amplitude of the plates and the maximum strains were measured in order to find an optimum position for placing a piezoelectric polymer to harvest energy from the flow.