离子液体分散液液微萃取/高效液相色谱法测定环境水样中7种萘二酚

建立了测定环境水样中7种萘二酚的离子液体分散液液微萃取/高效液相色谱(IL-DLLME-HPLC)分析方法。以1-丁基-3-甲基咪唑六氟磷酸盐([C4MIM][PF6])为萃取剂,水样体积为8.0 m L,研究了萃取剂用量、水相p H值、萃取时间及盐添加量对7种萘二酚萃取效率的影响。获得最佳萃取条件为:[C4MIM][PF6]体积为150μL,水相p H值为5.0~7.0,涡旋萃取时间为3 min,氯化钠添加量为0.20 g/m L。在优化条件下,7种萘二酚在一定质量浓度范围内线性关系良好,相关系数均不小于0.997 7;方法富集倍数为57倍,方法检出限(S/N=3)为0.3~1.0μg/L;阴性环境水样中3个加标水平的平均回收率为83.5%~103%,相对标准偏差(n=6)为1.1%~3.8%。该方法快速简单、准确灵敏、环保,适用于环境水样中痕量萘二酚的富集检测。     

基于低共熔溶剂的涡旋辅助悬浮固化-分散液液微萃取/高效液相色谱法测定水中三氯生与三氯卡班

建立了基于低共熔溶剂的涡旋辅助悬浮固化-分散液液微萃取(VA-DLLME-SFDES)结合高效液相色谱测定水样中三氯生和三氯卡班的新方法。合成了6种疏水性低共熔溶剂(DES)并测定其密度、熔点和辛醇-水分配系数(K_(OW))。选取其中低密度、合适凝固点的DES作为萃取剂,样品经涡旋辅助萃取后冷冻,萃取剂固化附着于离心管内壁,弃去水相后,融化离心进样。最佳萃取条件为:选取由薄荷醇∶十二醇(摩尔比为1∶2)制备的DES作为萃取剂,萃取剂用量为70μL,水样pH值调至5.0,涡旋时间为1 min。在最优条件下,三氯生和三氯卡班分别在0.59～100μg/L和0.26～100μg/L质量浓度范围内线性关系良好(r~2=0.999 8),方法检出限(S/N=3)为0.08～0.18μg/L,富集倍数为141～148倍,回收率为86.0%～115%,日内精密度(n=6)和日间精密度(n=6)均不大于5.4%。该方法简便、快速,且萃取相易于收集,适用于水中三氯生和三氯卡班的测定。     

超声辅助分散液液微萃取/超高效液相色谱-串联质谱法检测水中多种磺胺类抗生素残留

建立了水中13种磺胺类抗生素的超声辅助分散液液微萃取/超高效液相色谱-串联质谱(UADLLME/UPLC-MS/MS)测定方法。以乙腈为分散剂,四氯乙烷为萃取剂,通过超声分散方式协同萃取水样中的目标化合物,采用C_(18)(色谱柱(100 mm×2.1 mm,1.7μm)分离,以乙腈-0.1%甲酸溶液为流动相,采用UPLC-MS/MS多反应监测模式(MRM)测定。优化了萃取剂和分散剂的类型和用量、萃取时间、氯化钠浓度和p H值等条件。在优化条件下,13种磺胺类抗生素在一定质量浓度范围内线性关系良好,相关系数均大于0.998,方法检出限(S/N=3)为0.6~2.4 ng/L;3个加标水平的平均回收率为80.3%~101.8%,相对标准偏差(RSD,n=5)为0.7%~4.5%。该方法前处理简单、环保、灵敏,适用于水样中多种磺胺类抗生素的测定。     

有机悬浮固化分散液-液微萃取测定水样中痕量铅

建立了以二乙基二硫代氨基甲酸钠为配位剂,十二醇为萃取剂,乙醇为分散剂的悬浮固化分散液-液微萃取—火焰原子吸收光谱法测定水样中痕量铅的方法。详细探讨了影响萃取效率的因素。优化条件为:二乙基二硫代氨基甲酸钠的用量为10-6 mol,十二醇体积为90.00μL,乙醇体积为1.00 mL,pH为7.00。在最佳条件下,铅的检出限为1.12μg/L,富集倍率为16.00,线性范围5.00～600.00μg/L,对含有20.00μg/L和600.00μg/L Pb的标准溶液平行萃取测定11次,测定结果的RSD分别为3.73%和2.62%。本方法应用于自来水、河水及海水中痕量铅的分析,加标回收率为90.10%～100.70%。     

分散液液微萃取-高效液相色谱法测定环境水样中2,4-二氯酚

建立了简便、快速、有效的分散液液微萃取-高效液相色谱法测定环境水样中2,4-二氯酚的分析方法。对萃取剂、分散剂的种类和体积、萃取时间、离心时间、盐浓度等影响萃取效率的因素进行了优化。方法的线性范围为1～500μg/L(r=0.9997),相对标准偏差(RSD)为3.8%(n=6),检出限为0.19μg/L。该法适用于环境水样中的痕量2,4-二氯酚的检测。     

表面活性剂辅助-凝固-漂浮分散液液微萃取/高效液相色谱法测定环境水样中酚类化合物

建立了表面活性剂辅助-凝固-漂浮分散液液微萃取(SA-DLLME-SFO)/高效液相色谱法同时测定环境水样中4种酚类化合物的分析方法。SA-DLLME-SFO实验中选用十二醇为萃取剂,Tween 20为分散剂,考察了萃取剂和非离子表面活性剂的体积、萃取时间、离心时间和盐效应等因素对萃取效率的影响。结果表明:对硝基苯酚、对甲酚、对溴酚和双酚A的检出限分别为0.13,0.13,1.02,0.25 ng/m L;对硝基苯酚、对甲酚和双酚A的线性范围为2~4 000 ng/m L,对溴苯酚的线性范围为10~4 000 ng/m L;加标浓度为0.2,0.8μg/m L时,4种酚类化合物的回收率为96.6%~105%,相对标准偏差(RSD,n=5)为1.9%~4.9%。该方法可用于池塘水和湖水等天然水体中对硝基苯酚、对甲酚、对溴酚和双酚A的测定。     

分散液液微萃取-气相色谱/质谱法测定水中多环芳烃

用分散液液微萃取-气相色谱/质谱法测定水样中的16种多环芳烃(PAHs)。通过实验确定最佳萃取条件为:20μL四氯化碳作萃取剂,1.0 mL乙腈作分散剂,超声萃取1 min。在优化条件下,多环芳烃的富集倍数达到216～511,方法在0.05～50μg/L范围内呈良好的线性关系,相关系数(R2)在0.9873～0.9983之间,检出限为0.0020～0.14μg/L。相对标准偏差(RSD)在3.82%～12.45%(n=6)之间。该方法成功用于实际水样中痕量多环芳烃的测定。     

悬浮固化分散液液微萃取-高效液相色谱法测定水体中邻苯二甲酸酯

建立了悬浮固化分散液液微萃取（SFO-DLLME）结合高效液相色谱（HPLC）快速测定水样中6种邻苯二甲酸酯（PAEs）的分析方法。通过对影响萃取效率因素的优化,确定了最佳萃取条件：十二烷醇萃取剂20 μL、萃取温度60℃、离子强度20 g/L、萃取时间1 min。6种PAEs在2~2000 μg/L范围内呈良好的线性关系,相关系数（r）为0.9995~0.9999,检出限（S/N=3）为0.3~0.6 μg/L。对自来水、湖水、江水、污水、海水、市售塑料瓶装纯净水和矿泉水进行测定,能检测到部分PAEs。对加标水样进行回收率试验（10、100和1000 μg/L）,6种PAEs的回收率为84.9%~94.5%,相对标准偏差为4.1%~6.8%（n=5）。该法环保、简单,可用于实际水样中6种PAEs的检测分析。     

凝固-漂浮分散液液微萃取富集分光光度法测定水中亚硝酸根

研究了凝固-漂浮分散液液微萃取（SFO-DLLME）-分光光度法测定水样中痕量亚硝酸根的方法。以1-十二醇为萃取剂,乙醇为分散剂进行分散液液微萃取,离心后通过冷冻凝固操作使漂浮的萃取剂和水相分离。最佳实验条件下,方法的线性范围为2.0-280μg/L（r=0.999 9）,检出限为0.34μg/L。方法已成功应用于环境水样分析,相对标准偏差在2.4%-3.3%,加标回收率在98.2%-102.4%。     

液液萃取–气相色谱法测定地表水中硝基苯

采用液液萃取–气相色谱法测定地表水中硝基苯的含量。采用盐酸调节水样至pH值为4左右,在200mL水样中加入8 g氯化钠,以甲苯为萃取剂,以CD–5MS色谱柱进行分离,氢火焰离子化检测器检测地表水中硝基苯的含量。硝基苯的质量浓度在10~150μg/L范围内与色谱峰面积呈良好的线性关系,线性相关系数r=0.999 4,方法检出限为0.24μg/L。加标回收率在91.6%~96.7%之间,测定结果的相对标准偏差小于3(n=7)。该方法操作简便,灵敏度高,适用于地表水中硝基苯的分析。     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

The development and application of guidance on equipment qualification of analytical instruments

 This paper describes the development of guidance for the equipment qualification (EQ) of analytical instruments. EQ is a formal process that provides documented evidence that an instrument is fit for its intended purpose and kept in a state of maintenance and calibration consistent with its use.     

Effect of Transition Metals on Selective Hydrogenation of Cinnamaldehyde over Pt／ZrO2 Catalysts

The effect of transition metals (Cr, Mn, Fe, Co and Ni) on the hydrogenation of cinnamaldehyde over Pt/ZrO2 catalysts was studied in ethanol at 343K under 2.0MPa H2 pressure. PtCo/ZrO2 and PtFe/ZrO2 catalysts exhibit high selectivity and activity of hydrogenation for C=O (93.8% at 87.3% conversion and 83.6% at 88.6% conversion, respectively), and PtNi/ZrO2 exhibits high selectivity of hydrogenation for C=C (64.3% at 70.6% conversion). In the presence of trace H2O and NaOH, over the PtNi/ZrO2 (0.4wt%Ni) catalyst the selectivity to hydrocinnamalde hydereaches 90.6% and the conversion of cinnamaldehyde is 90.5%.     

Synthesis and Multinuclear NMR Study of Benzoyl Methylene Triparatolylphosphorane Ylide and the Reaction of this Ylide with Mercury(II) Halides

The reaction of the title ylide {PhCOCHP(p-tolyl)₃} with Pd(II), Pt(II). Hg(II), and Ag(I) in equimolar ratios using CH₃CN, CH₃OH, and CH₂Cl₂ as solvents have yielded [{(p-tolyl)₃PCHCOC₆H₅} PdCl₂]₂ (I), [{(p-tolyl)₃ PCHCOC₆H₅} PtCl₂]₂(2), [Hg(NO₃)₂ {(p-tolyl)₃ PCHCOC₆H₅}](3), and [Ag{(p-tolyl)₃ PCHCOC₆H₅ < eqid1 > ₂]⁺ (4). The IR, ¹H ¹³C, and ³¹P NMR together with micro analysis data of the products were obtained.     

Step-scan TMDSC and high rate DSC study of the multiple melting behavior of poly(1,3-propylene terephthalate)

The multiple melting behavior of poly(1,3-propylene terephthalate) (PPT) samples after isothermal crystallization from the melt was studied. The step-scan temperature-modulated differential scanning calorimetry (TMDSC) and high rate DSC were used to investigate this behavior in conjunction with standard DSC, wide-angle X-ray diffraction (WAXD) and polarizing light microscopy (PLM). The effect of PPT average molecular weight on the melting was also examined. In general multiple endotherms after isothermal crystallization of PPT were attributed to a continuous crystal perfection process during the subsequent heating scan via melting-recrystallization-remelting. Multiple melting behavior was more pronounced for the low molecular weight PPT. Step-scan TMDSC showed that extensive recrystallization occurs in PPT samples, especially after rapid isothermal crystallization. In fact two recrystallization exothermic peaks were observed. High rate DSC revealed the initial morphology generated during the isothermal step and showed that the low and middle peaks are associated with melting of primary crystals while the high temperature peak should be attributed to melting of recrystallized material.     

Biodegradations of block copolymers composed of L- or D,L-lactide and six-membered cyclic carbonates prepared with organolanthanide initiators

Diblock copolymerizations of L - or D,L -lactide (LA) with trimethylene carbonate (TMC) or 2,2-dimethyltrimethylene carbonate (2,2-DTMC) with SmMe(C₅Me₅)₂-(tetrahydrofuran) as an initiator and triblock copolymerizations of L - or D,L -LA/cyclic carbonates/L - or D,L -LA with [Sm(C₅Me₅)₂]₂(PhCCCCPh) as an initiator generated the desired block copolymers. This article describes the comparison of biodegradabilities by proteinase K and a compost and mechanical properties between the resulting di- or triblock copolymers and random copolymers composed of L - or D,L -LA and cyclic carbonates. The scanning electron microscopic profiles of resulting polymers were measured to understand the morphological change during biodegradation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3572–3588, 2003     

Novel Designing of Chemically Modified Electrode (CME) of the Bio-MOF-1 for the Detection of Dopamine Based on Inhibition of [Ru(bpy)3]2+/DBAE System

Metal organic frameworks (MOFs) have attracted extensive attention in electrochemical research fields due to their high surface area and controlled porosity. Current study is design to investigate the ECL performance of the chemically modified electrode (CME) based on the bio-MOF-1, a porous zinc-adenine framework, which loaded ruthenium complex and employed for the detection of dopamine (DA). The composite material [Ru(bpy)₃]²⁺@bio-MOF-1 (Ru-bMOF) modified carbon glassy electrode (Ru-bMOF/GCE) exhibited an excellent ECL performance having a linear co-efficient response (R²=0.9968) for 2-(dibutyl amino) ethanol (DBAE), a classical ECL co-reactant was obtained over a concentration range of 1.0×10⁻⁹ M to 1.0×10⁻⁴ M in 0.10 M pH=6.0 phosphate buffer solution (PBS). Furthermore, DA was detected based on its inhibition effect on [Ru(bpy)₃]²⁺/DBAE system. Compared to traditional analytical methods, this method has various advantages such as simple electrode preparation, quick response, high reproducibility (RSD<2.0 %), low limit of detection (LOD=1.0×10⁻¹⁰ mol/L). This chemical investigated modified electrode had exploited potential for detection of DA.     

improvement of the Specificity of Surface Plasmon Resonance with BSA-modified Chip

Recently, surface plasmon resonance (SPR) become more and more popular without the need of the label technology1-3. However, sometimes, a number of experimental artifacts complicate the final biosensor analysis4-7. The utilization of a reference surface c…     

Determination of carcinoembryonic antigen using a novel amperometric enzyme-electrode based on layer-by-layer assembly of gold nanoparticles and thionine

Electrochemical sensing of carcinoembryonic antigen(CEA)on a gold electrode modified by the se- quential incorporation of the mediator,thionine(Thi),and gold nanoparticles(nano-Au),through co- valent linkage and electrostatic interactions onto a self-assembled monolayer configuration is de- scribed in this paper.The enzyme,horseradish peroxidase(HRP),was employed to block the possible remaining active sites of the nano-Au monolayer,avoid the non-specific adsorption,instead of bovine serum albumin(BSA),and amplify the response of the antigen-antibody reaction.Electrochemical ex- periments indicated highly efficient electron transfer by the imbedded Thi mediator and adsorbed nano-Au.The HRP kept its activity after immobilization,and the studied electrode showed sensitive response to CEA and high stability during a long period of storage.The working range for the system was 2.5 to 80.0 ng/mL with a detection limit of 0.90 ng/mL.The model membrane system in this work is a potential biosensor for mimicking the other immunosensor and enzyme sensor.