Intermediate phases during alkali metal intercalation in HfNCl

The mechanism of the chemical and electrochemical alkali metal intercalation reactions in β-HfNCl has been investigated through electrochemical potential spectroscopy (EPS), in-situ powder X-ray diffraction during electrochemical intercalation and room temperature chemical intercalation experiments. EPS experiments in lithium cells reveal the presence of a plateau, at 1.8 V vs. Li⁺/Li⁰ accounting for ca. 0.14 mol Li, that indicates the formation of a new intermediate phase, and then a gradual decrease of potential with composition that extends up to very high lithium contents (ca. 1.1 per formula), consistent with the formation of a solid solution. Sodium electrochemical intercalation experiments showed a relatively similar behaviour with a plateau at 1.4 V vs. Na⁺/Na⁰, corresponding to ca. 1.7 V vs. Li⁺/Li⁰. In-situ monitored powder X-ray diffraction electrochemical intercalation experiments showed that the electrolyte solvent (ethylene carbonate/dimethyl carbonate, EC/DMC or propylene carbonate, PC) co-intercalated with the alkaline atom. This leads to a large expansion of the interlayer spacing that reaches a value of 21.06 Å in the lithium co-intercalated phase with EC/DMC, Li_x(EC/DMC)_yHfNCl, and 22.01 Å in the sodium co-intercalated phase with PC, Na_x(PC)_yHfNCl. Chemical intercalation using naphthyl-sodium solutions in tetrahydrofuran (THF) leads to solvent-free, multiple-phase samples showing in different proportions the pristine and the superconducting stage 2 and stage 1 phases. The composition of the intercalated samples depends on the pristine sample, the concentration of the naphthyl-sodium solution, the ratio Na:HfNCl and the reaction time. Pristine samples exhibiting low lithium intercalation degree upon electrochemical reduction gave the second stage as the major phase when treated with short reaction times or using low Na:HfNCl ratios, coexisting either with the host or with the first stage phase, whereas stage 1 is obtained as the major phase from pristine samples showing high electrochemical capacities. The staging behaviour and the multiphase nature of these samples account for the wide superconducting transitions and the different critical temperatures observed in these superconductors.     

Analysis of degradation of electrolytic Fe, Co, Ni sulfides and their graphitized analogs in lithium battery using impedance spectroscopy

Changes in parameters of complex-plane plots are analyzed for electrolytic Me _x S _y electrodes (Me = Fe, Co, Ni) and their graphitized analogs contacting electrolyte (ethylene carbonate, dimethyl carbonate, 1 M LiClO₄) in the case of degradation in a layout lithium battery at cycle 15. Impedance measurements in the high- and medium-frequency region of complex-plane plots revealed the key role of the surface solid-phase film and also of resistance of charge transfer through the sulfide material/electrolyte interface in degradation of Me _x S _y electrodes under cycling in the potential range of 2.80?0.02 V vs. Li/Li⁺. The activation energy is determined for processes of charge transfer through the electrode/electrolyte interface.     

Solvation Structure with Enhanced Anionic Coordination for Stable Anodes in Lithium-Oxygen Batteries

Li-O₂ batteries have garnered much attention due to their high theoretical energy density. However, the irreversible lithium plating/stripping on the anode limits their performance, which has been paid little attention. Herein, a solvation-regulated strategy for stable lithium anodes in tetraethylene glycol dimethyl ether (G4) based electrolyte is attempted in Li-O₂ batteries. Trifluoroacetate anions (TFA⁻) with strong Li⁺ affinity are incorporated into the lithium bis(fluorosulfonyl)imide (LiTFSI)/G4 electrolyte to attenuate the Li⁺-G4 interaction and form anion-dominant solvates. The bisalt electrolyte with 0.5 M LiTFA and 0.5 M LiTFSI mitigates G4 decomposition and induces an inorganic-rich solid electrolyte interphase (SEI). This contributes to decreased desolvation energy barrier from 58.20 to 46.31 kJ mol⁻¹, compared with 1.0 M LiTFSI/G4, for facile interfacial Li⁺ diffusion and high efficiency. It yields extended lifespan of 120 cycles in Li-O₂ battery with a limited Li anode (7 mAh cm⁻²). This work gains comprehensive insights into rational electrolyte design for Li-O₂ batteries.     

Influence of sol–gel derived lithium cobalt phosphate in alkaline rechargeable battery

A lithium cobalt phosphate (LiCoPO₄) cathode was synthesised by citric acid assisted sol?Cgel method and its electrochemical behaviour in alkaline secondary battery (using novel lithium hydroxide as the electrolyte) is reported. The sol?Cgel method using metal acetate precursors with citric acid as a chelating agent influenced the particle size and the homogeneity while yielding a single phase LiCoPO₄ at a considerably lower temperature and shortened heating time, compared to that of the conventional solid state reaction. The cyclic voltammogram of LiCoPO₄ showed a reversible redox process implying that de-intercalation and intercalation of lithium can occur in aqueous electrolyte. This was supported by X-ray diffraction (XRD) and Infra-red (IR) studies. The charge?Cdischarge performance of the Zn/LiCoPO₄ battery showed good capacity retention (after 25 cycles it delivered 90?% of its initial capacity). This enhanced capacity retention was attributed to the synergistic effect of particle homogeneity, reduced Li⁺ diffusion path and stability of the non-reactive aqueous electrolyte between the electrode and the electrolyte interface.     

Impedance study on the correlation between phase transition and electrochemical degradation of Si-based materials

In order to explain the relationship between physical change and electrochemical degradation of Co–Co₃O₄ coated Si, impedance spectroscopy on Co–Co₃O₄ coated Si was conducted at various states during charge or discharge. Nyquist plots during Li⁺ insertion (charge) showed a unique behavior that below 70 mV vs. Li/Li⁺, the more Li⁺’s were inserted into the electrode, the larger its comprehensive resistance was getting. During Li⁺ extraction (discharge), electrode resistance was decreased after going through 0.43 V vs Li/Li⁺. When these data were fitted with the ordinary equivalent circuit which is composed of electrolyte resistance, charge transfer resistance and contact resistance, there was an abrupt augmentation of charge transfer resistance below 70 mV vs. Li/Li⁺ during charge, whereas there was its drastic diminishment between 0.2 and 0.5 V vs. Li/Li⁺ during discharge. Because these potential regions are each related to amorphous Li_xSi-to-Li₁₅Si₄ transition and vice versa, it could be shown that the formation and decomposition of Li₁₅Si₄ is responsible for the electrochemical degradation of Co–Co₃O₄ coated Si.     

A Perovskite Electrolyte That Is Stable in Moist Air for Lithium‐Ion Batteries

Solid‐oxide Li⁺ electrolytes of a rechargeable cell are generally sensitive to moisture in the air as H⁺ exchanges for the mobile Li⁺ of the electrolyte and forms insulating surface phases at the electrolyte interfaces and in the grain boundaries of a polycrystalline membrane. These surface phases dominate the total interfacial resistance of a conventional rechargeable cell with a solid–electrolyte separator. We report a new perovskite Li⁺ solid electrolyte, Li_0.38Sr_0.44Ta_0.7Hf_0.3O_2.95F_0.05, with a lithium‐ion conductivity of σ_Li=4.8×10^?4 S cm^?1 at 25 °C that does not react with water having 3≤pH≤14. The solid electrolyte with a thin Li⁺‐conducting polymer on its surface to prevent reduction of Ta⁵⁺ is wet by metallic lithium and provides low‐impedance dendrite‐free plating/stripping of a lithium anode. It is also stable upon contact with a composite polymer cathode. With this solid electrolyte, we demonstrate excellent cycling performance of an all‐solid‐state Li/LiFePO₄ cell, a Li‐S cell with a polymer‐gel cathode, and a supercapacitor.     

Electrolytic molybdenum oxides in lithium batteries

Nonstoichiometric molybdenum oxides (e-Mo_xO_y) were synthesized by cathodic reduction of aqueous ammonium and sodium molybdate solutions. Surface morphology of electrolytic (e) deposits, the chemical composition, crystal lattice structure, and the characteristics of electrochemical Li⁺ intercalation for such synthesized oxides were determined by the cation composition of molybdate solution and the conditions of deposit annealing. The electrochemical intercalation of Li⁺ ions in these Mo-oxides was investigated in thin-layer ballast-free electrodes, as a pasted mposite cathode in lithium batteries, and as an anode in lithium-ion batteries, with liquid organic and polymer electrolytes. The reversible discharge capacity of e-Mo₄O₁₁ synthesized from ammonium molybdate electrolyte in thin-layer ballast-free electrodes can exceed 225 mAh g^–1 for more than 170 cycles.     

The search for a solid electrolyte,as a polysulfide barrier,for lithium/sulfur batteries

Composite Li₁₀SnP₂S₁₂ (LSPS)/polyethylene oxide (PEO) films, containing 25 to 50 % polymer, were electrophoretically deposited from acetone-based suspension and tested as possible candidates for polysulfide barriers in Li/S batteries. It was found by XRD and XPS tests that saturation of composite films by LiI salt, followed by prolonged annealing at 90 °C, diminishes the crystallinity of neat LSPS and results in the formation of a novel composite Li_10+xI_xSnP₂S₁₂ (LISPS)/P(EO)₃/LiI solid electrolyte (x < 1). The high room-temperature ion conductivity of amorphous sulfide Li_10+xI_xSnP₂S₁₂ (0.1–0.3 mS cm^?1) is restricted by slow ion transport via the polymer electrolyte (PE) imbedded in ceramics and grain boundaries between the PE and sulfide. Increase in polymer content and temperature improves total ion transport in the LISPS/PEO system. Conformal EPD coating of sulfur and lithium sulfide cathodes by the developed composite electrolyte increased the reversible capacity and Faradaic efficiency of the Li/S and Li/Li₂S cells and enabled their operation at 60 °C.     

Thermodynamics of Lithium Intercalates in Carbonized Fabric

The method of quasi-equilibrium galvanostatic curves was applied to study the thermodynamics of lithium deintercalation from the system Li _x C₆ (solid phase)/Li⁺ (solution) in the interval 293-323 K and the thermodynamic characteristics (G, S, H) of lithium intercalation compounds in a carbonized fabric in relation to the degree of intercalation x.     

Li2SO4-polyacrylamide polymer electrolytes for 2.0 V solid symmetric supercapacitors

A neutral polymer electrolyte comprised of lithium sulfate (Li₂SO₄) and polyacrylamide (PAM) was developed. The Li₂SO₄-PAM electrolyte film shows an ionic conductivity up to 10 mS cm^− 1 in 45%RH conditions. Solid double layer capacitors were demonstrated using CNT-graphite electrodes and Li₂SO₄-PAM solid electrolytes. The voltage window of the solid cell was about 2.0 V, identical to that of a Li₂SO₄ liquid cell used as baseline. The demonstrated voltage window is significantly larger than that reported for proton- or hydroxyl-conducting electrolytes, suggesting that the Li₂SO₄-PAM electrolyte is a promising system for high energy density supercapacitors. The solid device also demonstrated excellent rate capability (up to 5 V s^− 1) and good cycle life (beyond 10,000 charge/discharge cycles).     

Li7P3S11电解质的合成、传导及应用

固态电解质是固态电池中的关键材料,开发具有高离子电导率、高化学/电化学稳定性、电极兼容性良好的固态电解质正成为研究热点。硫化物固态电解质相较其它固态电解质具有更高的离子电导率和良好的机械加工性能等优势,是最有前景实现实用化的固态电解质之一。在众多硫化物固态电解质中,Li₇P₃S₁₁因其高的离子电导率和较低的原料成本而极具研究意义。本文首先介绍了Li₇P₃S₁₁电解质的结构、Li+传导机理及合成路径;其次,针对该电解质的电导率提高、空气/水稳定性提升、固固界面稳定性及电解质自身稳定性改善等问题,综述了目前常用的改性策略研究;再次,总结了基于Li₇P₃S₁₁电解质的全固态锂离子电池和全固态锂硫电池的构筑;最后,本文分析了Li₇P₃S₁₁电解质的研究和应用面临的挑战,并指出该电解质未来发展的趋势。     

Novel technique to form electrode–electrolyte nanointerface in all-solid-state rechargeable lithium batteries

The electrode–electrolyte nanocomposites, where the nano-sized NiS electrode with large capacity was embedded in the 80Li₂S · 20P₂S₅ electrolyte with high Li⁺ conductivity, were successfully prepared by the mechanochemical method. Contact area of solid–solid interface between the electrode and the electrolyte was remarkably increased in the nanocomposites. All-solid-state cell using the nanocomposites as a working electrode exhibited larger capacity and better cycling performance than the cell using the electrode obtained by conventional hand-mixing of powders. The mechanochemical technique sheds light on a new formation process of electrode–electrolyte interfaces endowing solid-state batteries with high power density and high energy density.     

Molybdenum cluster chalcogenides Mo6X8: Electrochemical intercalation of closed shell ions Zn2+, Cd2+, and Na

The intercalation ofd¹⁰ ions Zn²⁺ and Cd²⁺ by electron/ion transfer reactions into the Chevrel-type molybdenum cluster chalcogenidesMo₆X₈ (X =S, Se) demonstrates the competitive influence of electronic and steric factors upon these processes. The following rhombohedral phases have been identified: Zn₁Mo₆S₈, Zn₂Mo₆S₈, Zn₁Mo₆Se₈, Zn₂Mo₆Se₈, Cd₁Mo₆S₈, Cd₁Mo₆Se₈, and Cd₂Mo₆Se₈. Thermodynamic data and chemical diffusion coefficients are given. The intercalation of Na⁺, which has an ionic radius close to that of Cd²⁺, exhibits a strong influence of kinetics leading to the partial irreversibility of the reaction and the formation Na₁Mo₆S₈ and Na₁Mo₆Se₈, the first cubic phases among the molybdenum cluster chalcogenidesA_xMo₆X₈.     

Ion-selective sensors based on molybdenum bronzes

New pH- and sodium ion-sensitive metal-oxide-type sensors have been developed and tested with a direct solid state contact method. Performance was demonstrated at ambient temperature with single crystals of several molybdenum bronzes (i.e. Na_0.9Mo₆O₁₇, Li_0.9Mo₆O₁₇, Li_0.33MoO₃ and K_0.3MoO₃). The pH sensors with Na-molybdenum-oxide bronzes show near ideal Nernstian behavior in the pH range 3–9. The response is not affected by the direction of the pH change. The response time of most molybdenum bronze pH sensors is less than 5 s for 90% response. The sodium molybdenum bronze sensor responded reproducibly and fast to changes of Na⁺ concentration in the range 1–10^–4 mol dm^–3. Cross sensitivity tests to other ions such as H⁺ or K⁺ have shown that the new sodium ion sensor may be used when the concentration of other ions is an order of magnitude smaller than the Na⁺ concentration. pH sensors with single crystals of molybdenum oxide bronzes can be used to follow pH titrations. Electronic Publication     

Full Dissolution of the Whole Lithium Sulfide Family (Li2S8 to Li2S) in a Safe Eutectic Solvent for Rechargeable Lithium–Sulfur Batteries

The lithium–sulfur battery is an attractive option for next‐generation energy storage owing to its much higher theoretical energy density than state‐of‐the‐art lithium‐ion batteries. However, the massive volume changes of the sulfur cathode and the uncontrollable deposition of Li₂S₂/Li₂S significantly deteriorate cycling life and increase voltage polarization. To address these challenges, we develop an ?‐caprolactam/acetamide based eutectic‐solvent electrolyte, which can dissolve all lithium polysulfides and lithium sulfide (Li₂S₈–Li₂S). With this new electrolyte, high specific capacity (1360 mAh g^?1) and reasonable cycling stability are achieved. Moreover, in contrast to conventional ether electrolyte with a low flash point (ca. 2 °C), such low‐cost eutectic‐solvent‐based electrolyte is difficult to ignite, and thus can dramatically enhance battery safety. This research provides a new approach to improving lithium–sulfur batteries in aspects of both safety and performance.     

One-Step In Situ Polymerization: A Facile Design Strategy for Block Copolymer Electrolytes

To optimize the rapid transport of lithium ions (Li⁺) inside lithium metal batteries (LMBs), block copolymer electrolytes (BCPEs) have been fabricated in situ in LMBs via a one-step method combining reversible addition-fragmentation chain transfer (RAFT) polymerization and carboxylic acid-catalyzed ring-opening polymerization (ROP). The BCPEs balanced the Li⁺ coordination characteristics of the polyether- and polyester-based electrolytes to achieve a rapid Li⁺ migration in the SPEs. The carboxylic acid played a dual role since it both catalyzed the ROP and stabilized the interface. Furthermore, the in situ assembly of LMBs did effectively enable an efficient intercalation/de-intercalation of Li⁺ at the electrode/electrolyte interface. The in situ assembled Li/BCPE4/LFP exhibited high-capacity retention of 92 % after 400 cycles at 1 C. The one-step in situ fabrication of BCPEs provides a new direction for the design of polymer electrolytes.     

In-Situ Constructing A Heterogeneous Layer on Lithium Metal Anodes for Dendrite-Free Lithium Deposition and High Li-ion Flux

Constructing efficient artificial solid electrolyte interface (SEI) film is extremely vital for the practical application of lithium metal batteries. Herein, a dense artificial SEI film, in which lithiophilic Zn/Li_xZn_y are uniformly but nonconsecutively dispersed in the consecutive Li⁺-conductors of Li_xSiO_y, Li₂O and LiOH, is constructed via the in situ reaction of layered zinc silicate nanosheets and Li. The consecutive Li⁺-conductors can promote the desolvation process of solvated-Li⁺ and regulate the transfer of lithium ions. The nonconsecutive lithiophilic metals are polarized by the internal electric field to boost the transfer of lithium ions, and lower the nucleation barrier. Therefore, a low polarization of ≈50 mV for 750 h at 2.0 mA cm⁻² in symmetric cells, and a high capacity retention of 99.2 % in full cells with a high lithium iron phosphate areal loading of ≈13 mg cm⁻² are achieved. This work offers new sights to develop advanced alkali metal anodes for efficient energy storage.     

Excellent Stability of a Lithium‐Ion‐Conducting Solid Electrolyte upon Reversible Li+/H+ Exchange in Aqueous Solutions

Batteries with an aqueous catholyte and a Li metal anode have attracted interest owing to their exceptional energy density and high charge/discharge rate. The long‐term operation of such batteries requires that the solid electrolyte separator between the anode and aqueous solutions must be compatible with Li and stable over a wide pH range. Unfortunately, no such compound has yet been reported. In this study, an excellent stability in neutral and strongly basic solutions was observed when using the cubic Li₇La₃Zr₂O₁₂ garnet as a Li‐stable solid electrolyte. The material underwent a Li⁺/H⁺ exchange in aqueous solutions. Nevertheless, its structure remained unchanged even under a high exchange rate of 63.6 %. When treated with a 2 M LiOH solution, the Li⁺/H⁺ exchange was reversed without any structural change. These observations suggest that cubic Li₇La₃Zr₂O₁₂ is a promising candidate for the separator in aqueous lithium batteries.     

Stabilization of Th ions into mixed-valence thorium fluoride

The unusual oxidation state +3 of the thorium has been stabilized into a lithium containing non-stoichiometric mixed-valence (III/IV) thorium fluorinated phase with formula Li_2+xTh₁₂F₅₀ (0<x<1.8). This phase is closely related to the Li_5.5Ce₁₂F₅₀ one, the structure of which has been determined from the combined single-crystal X-ray diffraction and high resolution synchrotron powder diffraction. In these phases, the Li⁺ ions can be divided into two groups and are located either in locked positions or in open channels of the three dimensional framework. The amount of Li⁺ ions in open channels can be variable, so that the afore mentioned single phase may be considered as an insertion compound. The Li⁺ insertion is accompanied by the simultaneous reduction of a part of the Th⁴⁺ ions, resulting in a mixed-valence III/IV thorium fluoride. The electrochemical insertion of Li⁺ ions into the open channels of the host matrix has been carried out at 60 °C, using an alkylcarbonate PC-LiClO₄ 1 M electrolyte. The Li⁺ and Th³⁺ contents, both in the starting composition and the Li⁺ inserted ones, were investigated by high resolution solid state ⁷Li NMR and EPR, respectively.     

Ultrafast anode for high voltage aqueous Li-ion batteries

Clustered Mo sulfide Mo₆S₈ (Chevrel phase) demonstrates outstandingly high rate capability in contact with concentrated aqueous Li₂SO₄ solutions. Slow galvanostatic cycling can be performed with good Faradaic efficiency at a moderate capacity of 32.1?mAhg^{? 1} (1e^? reduction of Mo₆S₈), which in combination with 1e^? oxidation process in Li _x Mn₂O₄ cathode, results in equilibrium cell voltage of 1.5?V. Higher rates of charge and discharge have been also achieved within a considerably extended apparent electrochemical stability window involving second two-electron reduction of Mo₆S₈ which leads to apparent cell voltage of 1.85?V, specific capacity about 74.7?mAhg^?1 at 90?% Faradaic efficiency, specific energy of 74?Wh?kg^?1 (related to both electrodes) at extremely high charge–discharge rate of 60?C. Our study highlights the generic feature of Li-ion aqueous cells, namely, a high rate capability coupled with a relatively fast self-discharge which necessitates a more profound understanding of the nature of self-discharge in Li-ion insertion hosts in contact with aqueous solutions.