Contact angle hysteresis of bovine serum albumin (BSA) solution/metal (Au-Cr) coated glass substrate

Bovine serum albumin (BSA) has an extraordinary property to carry biomolecules. An experimental study on the wettability of BSA is presented in this study. The variations in the surface tension and the equilibrium contact angle with the change in BSA concentration are also reported. The surface tension and the contact angle are measured with pendant and sessile drop techniques, respectively. A nonlinear decrement in the surface tension with the increment in the BSA concentration is observed. An equilibrium contact angle of a BSA solution with particular concentration is determined by studying the hysteresis in the contact angle from dynamic contact angle measurements. The needle-in-drop technique is used to study the hysteresis of the contact angle. It is observed that the obtained surface tension and the equilibrium contact angle vary with the BSA concentration. In this reported study, for the considered combination of the BSA concentration and solid surface, the liquid drop does not recede as the drop volume decreases, which represents nonreceding contact angle condition. The increment in the contact angle with the increment in the BSA concentration is observed. Finally, it is observed that the inclusion of the proteins not only changes the surface tension but also changes the contact angle.     

Contact angle hysteresis of cylindrical drops on chemically heterogeneous striped surfaces

Contact angle hysteresis of a macroscopic droplet on a heterogeneous but flat substrate is studied using the interface displacement model. First, the apparent contact angle of a droplet on a heterogeneous surface under the condition of constant volume is considered. By assuming a cylindrical liquid-vapor surface (meniscus) and minimizing the total free energy, we derive an equation for the apparent contact angle, which is similar but different from the well-known Cassie's law. Next, using this modified Cassie's law as a guide to predict the behavior of a droplet on a heterogeneous striped surface, we examine several scenarios of contact angle hysteresis using a periodically striped surface model. By changing the volume of the droplet, we predict a sudden jump of the droplet edge, and a continuous change of the apparent contact angle at the edge of two stripes. Our results suggest that as drop volume is increased (advancing contact lines), the predominant drop configuration observed is the one whose contact angle is large; whereas, decreasing drop volume from a large value (receding contact lines) yields drop configuration that predominantly exhibit the smaller contact angle.     

Droplet compression and relaxation by a superhydrophobic surface: contact angle hysteresis

In this article, the contact angle hysteresis (CAH) of acrylic glass is experimentally and theoretically studied through the compression-relaxation process of droplets by using a superhydrophobic surface with negligible CAH effect. In contrast to the existing technique in which the volume of the droplet changes during the measurement of CAH, this procedure is carried out at a constant volume of the droplet. By observing the base diameter (BD) and the contact angle (CA) of the droplet during the compression-relaxation process, the wetting behavior of the droplet can be divided into two regimes, the contact line withdrawal and the contact line pinning regimes, depending on the gap thickness (H) at the end of the compression process. During the compression process, both regimes possess similar droplet behavior; the contact line will move outward and the BD will expand while the CA remains at the advancing angle. During the relaxation process, the two regimes are significantly different. In the contact line withdrawal regime, the contact line will withdraw with the CA remaining at the receding angle. In the contact line pinning regime, however, the contact line will be pinned at the final position and the CA will decline to a certain value higher than the receding angle. Furthermore, the advancing pinning behavior can also be realized through a successive compression-relaxation process. On the basis of the liquid-induced defects model, Surface Evolver simulations are performed to reproduce the behavior of the droplet during the compression-relaxation process; both contact line withdrawal and pinning regimes can also be identified. The results of the experiment and simulation agree with each other very well.     

Line energy and the relation between advancing, receding, and young contact angles

The line energy associated with the triple phase contact line is a function of local surface defects (chemical and topographical); however, it can still be calculated from the advancing and receding contact angles to which those defects give rise. In this study an expression for the line energy associated with the triple phase contact line is developed. The expression relates the line energy to the drop volume, the interfacial energies, and the actual contact angle (be it advancing, receding, or in between). From the expression we can back calculate the equilibrium Young contact angle, theta0, as a function of the maximal advancing, thetaA, and minimal receding, thetaR, contact angles. To keep a certain maximal hysteresis between advancing and receding angles, different line energies are required depending on the three interfacial energies and the drop's volume V. We learn from the obtained expressions that the hysteresis is determined by some dimensionless parameter, K, which is some normalized line energy. The value of K required to keep a constant hysteresis (thetaA-thetaR) rises to infinity as we get closer to theta0 = 90 degrees.     

Water microdroplets on molecularly tailored surfaces: correlation between wetting hysteresis and evaporation mode switching

The evaporation of water microdroplets from solid surfaces was studied using digital contact angle analysis techniques. An inclusive trend for the evaporation process, that is, a switch from the initial constant contact area to the subsequent constant contact angle mode was observed for all surfaces examined, including mixed self-assembled monolayers (SAMs) on gold and "conventional" surfaces such as silicon wafers, polycarbonate, and Teflon. More importantly, it has been shown that the change in contact angle during the evaporation process (i.e., evaporation hysteresis, delta theta(evap), the difference between the initial and "equilibrated" contact angle) correlates well with the wetting hysteresis determined directly (i.e., measuring the advancing and receding contact angles on these surfaces by changing the drop volume). The comparison between mixed SAM surfaces and conventional solids revealed that the evaporation/wetting hysteresis is dominated by the roughness (from nanometer to micrometer scale) rather than the chemical heterogeneity of the surface. The evaporation rates of water microdroplets on these surfaces were also monitored and modeled.     

Contact angle hysteresis at the nanoscale: a molecular dynamics simulation study

In this paper, the contact angle hysteresis (CAH) of nanodroplets on both rigid and flexible substrates with different wettabilities was studied using molecular dynamics (MD) simulations. The critical shear stress (CSS) that determines the motion of the contact line (CL) was investigated. A theoretical correlation between CAH and CSS was proposed. Both CAH and CSS reflect the energy dissipation at the CL of the droplet in response to the exerted force. MD results of CAH are qualitatively consistent with the theoretical model. Simulation results also show that, for the same liquid–solid interactions, CAH on the flexible substrate is larger than that on the rigid substrate. These findings aim to enhance our understanding of the mechanism of the CAH at the nanoscale.     

The wetting behavior of grafted hydrophilic acrylic monomers

The wetting behavior of vapor phase photografted hydrophilic acrylic monomers was evaluated by the three most commonly employed techniques, i.e., the captive bubble, the sessile drop, and the Wilhelmy plate technique. The measured contact angles and the overall wetting behavior were discussed in light of the non-ideal nature of these surfaces.It was found that the peculiar nature of hydrophilic grafted surfaces is carefully reflected in the experimentally measurable contact angles. While in the case of the captive bubble the hydrophilic and rough nature of these coatings prevent the bubble-surface contact, in the case of the sessile drop the measured contact angles follow the behavior predicted by contact angle hysteresis theories. Wilhelmy plate measurements, performed as sequential scanning loops, show velocity-dependent effects which are linked to the composition, morphology and mobility of the grafted surfaces.     

Drops down the hill: theoretical study of limiting contact angles and the hysteresis range on a tilted plate

The limiting inclination angle (slip angle), for which a two-dimensional water drop may be at equilibrium on a chemically heterogeneous surface, is exactly calculated for a variety of cases. The main conclusion is that, in the cases studied, the contact angles at the upper and lower contact line do not always simultaneously equal the receding and advancing contact angles, respectively. On a hydrophobic surface, the lowest contact angle (at the upper contact line) tends to be approximately equal to the receding contact angle, while the highest contact angle (at the lower contact line) may be much lower than the advancing contact angle. For hydrophilic surfaces, the opposite is true. These conclusions imply that the hysteresis range cannot in general be measured by analyzing the shape of a drop on an inclined plane. Also, the limiting inclination angle cannot in general be calculated from the classical equation based only on the advancing and receding contact angles.     

Liquid Drops on an Inclined Plane: The Relation between Contact Angles, Drop Shape, and Retentive Force

Contact angle hysteresis, drop shape, and drop retention were studied with a tiltable plane. Contact liquids were water and ethylene glycol. Four polymers and silicon wafers were used as substrates. When the plane was inclined, the shape of drops distorted, exhibiting advancing and receding contact angles. Drops remained stationary until a critical angle of tilt was exceeded, and then they began to move. The difference in the advancing and receding contact angles, or contact angle hysteresis, ranged from 9° to 66°, depending on the liquid and the substrate. Roughness did not seem to influence the hysteresis as much as the chemical nature of the surfaces. Elongation and back-to-front asymmetry were greater on surfaces with high hysteresis. We found a linear correlation between the aspect ratio of drops and their contact angle hysteresis. Also, the retentive force increased with elongation of the drops.     

Sliding behavior of liquid droplets on tilted Langmuir-Blodgett surfaces

The sliding behavior of liquid droplets on inclined Langmuir-Blodgett surfaces was investigated. The critical sliding angle defined as the tilt angle of the surface at which the drop slides down as well as the advancing and receding contact angles was measured for five different liquids on five surfaces. In addition, the contact line geometry was analyzed at critical sliding angle. The experimental relationship between the surface tension forces resulting from contact angle hysteresis and the weight of the drop was compared to theoretical predictions. Even though the shape of the drop bases was found as skewed ellipses, a model assuming parallel-sided elongated drops is shown to describe reasonably the experimental values. This result probably indicates the main influence of the capillary forces at the rear and front edges of the drop with respect to that exerted on the lateral sides.     

A thermodynamic approach for determining the contact angle hysteresis for superhydrophobic surfaces

Contact angle hysteresis (CAH) is critical to superhydrophobicity of a surface. This study proposes a free energy thermodynamic analysis (of a 2-D model surface) that significantly simplifies calculations of free energy barrier associated with CAH phenomena. A microtextured surface with pillar structure, typical of one used in experimental studies, is used as an example. We demonstrate that the predicted CAH and equilibrium contact angles are consistent with experimental observations and predictions of Wenzel's and Cassie's equations, respectively. We also establish a criterion for transition between noncomposite and composite wetting states. The results and methodology presented can potentially be used for designing superhydrophobic surfaces.     

Bioadhesion to solids: contact angle hysteresis effect

It was recently reported that the ease of removal of sporelings of green seaweed Ulva under shear stress from the polymer surfaces was found to be linearly and positively correlated with contact angle and wetting hysteresis, i.e., the higher the hysteresis, the greater the removal. Motivated by this report, we examined the relationship between the bioadhesion of blood platelets and proteins with contact angle hysteresis of solid substrates using the data of published papers. It was determined that there is a linear and positive relationship between the contact angle hysteresis and bioadhesion of both blood platelets and γ-globulin protein contacting the solid substrates, i.e., the higher the hysteresis, the greater the bioadhesion. The reasons are discussed and it is proposed that testing the effect of CAH on the adhesion strengths of biomaterials on surfaces is useful in order to gain a better insight on the bioadhesion mechanism.     

Anisotropic wetting behavior arising from superhydrophobic surfaces: parallel grooved structure

It has been found experimentally that superhydrophobic surfaces exhibit strong anisotropic wetting behavior. This study reports a simple but robust thermodynamic methodology to investigate the anisotropic superhydrophobic behavior for parallel grooved surfaces. Free energy and its barrier and the corresponding contact angle and its hysteresis for various orientations of the groove structure are calculated based on the proposed thermodynamic model. It is revealed that the strong anisotropy of equilibrium contact angle (ECA) and contact angle hysteresis (CAH) is shown in the noncomposite state but almost isotropic wetting properties are exhibited in the composite state. Furthermore, for the noncomposite state, decreasing groove width and spacing or increasing groove depth can amplify the anisotropy for ECA. Meanwhile, decreasing groove width and increasing depth can amplify the anisotropy for CAH, while varying groove spacing can barely influence CAH. For the composite state, however, the surface geometry hardly leads to the anisotropic behavior. In addition, using a fitting approximation, a simple quantitative correlation between wettability and orientation can be established well, which is consistent with the numerical calculations.     

On some relations between advancing, receding and Young's contact angles

Problems of experimental determination and theoretical verification of equilibrium contact angles are discussed basing on the literature data. A relationship between the advancing and receding contact angles versus the equilibrium contact angle is described and then verified using the literature contact angles determined on paraffin wax and polypropylene. Using the proposed relationship and experimentally determined equilibrium contact angles, obtained by plotting the advancing and receding contact angles versus the contact angle hysteresis or by applying vibration of the system liquid drop/solid surface, it is found that the same value of the surface free energy for paraffin wax is calculated from the contact angles of water and ethylene glycol. However, in the case of polypropylene some inconsistency appears between the equilibrium contact angles of the probe liquid used and the calculated surface free energy. More experimental data of the equilibrium contact angle are needed to verify further the relationship.     

Spreading, evaporation, and contact line dynamics of surfactant-laden microdrops

An optical technique based on the reflectivity measurements of a thin film was used to experimentally study the spreading, evaporation, contact line motion, and thin film characteristics of drops consisting of a water-surfactant (polyalkyleneoxide-modified heptamethyltrisiloxane, called superspreader) solution on a fused silica surface. On the basis of the experimental observations, we concluded that the surfactant adsorbs primarily at the solid-liquid and liquid-vapor interfaces near the contact line region. At equilibrium, the completely wetting corner meniscus was associated with a flat adsorbed film having a thickness of approximately 31 nm. The calculated Hamaker constant, A = -4.47 x 10(-)(20) J, shows that this thin film was stable under equilibrium conditions. During a subsequent evaporation/condensation phase-change process, the thin film of the surfactant solution was unstable, and it broke into microdrops having a finite contact angle. The thickness of the adsorbed film associated with the drops was lower than that of the equilibrium meniscus. The drop profiles were experimentally measured and analyzed during the phase-change process as the contact line advanced and receded. The apparent contact angle, the maximum concave curvature near the contact line region, and the convex curvature of the drop increased as the drop grew during condensation, whereas these quantities decreased during evaporation. The position of the maximum concave curvature of the drop moved toward the center of the drop during condensation, whereas it moved away from the center during evaporation. The contact line velocity was correlated to the observed experimental results and was compared with the results of the drops of a pure alcohol. The experimentally obtained thickness profiles, contact angle profiles, and curvature profiles of the drops explain how the surfactant adsorption affects the contact line motion. We found that there was an abrupt change in the velocity of the contact line when the adsorbed film of the surfactant solution was just hydrated or desiccated during the phase-change processes. This result shows the effect of vesicles and aggregates of the surfactant on the shape evolution of the drops. For these surfactant-laden water drops, we found that the apparent contact angle increased during condensation and decreased during evaporation. However, for the drop of a pure liquid (n-butanol and 2-propanol) the apparent contact angle remained constant at a constant velocity during condensation and evaporation. The contact line was pinned during the evaporation and spreading of the surfactant-laden water drops, but it was not pinned for a drop of a pure alcohol (self-similar shape evolution).     

Modeling contact angle hysteresis of a liquid droplet sitting on a cosine wave-like pattern surface

A liquid droplet sitting on a hydrophobic surface with a cosine wave-like square-array pattern in the Wenzel state is simulated by using the Surface Evolver to determine the contact angle. For a fixed drop volume, multiple metastable states are obtained at two different surface roughnesses. Unusual and non-circular shape of the three-phase contact line of a liquid droplet sitting on the model surface is observed due to corrugation and distortion of the contact line by structure of the roughness. The contact angle varies along the contact line for each metastable state. The maximum and minimum contact angles among the multiple metastable states at a fixed viewing angle correspond to the advancing and the receding contact angles, respectively. It is interesting to observe that the advancing/receding contact angles (and contact angle hysteresis) are a function of viewing angle. In addition, the receding (or advancing) contact angles at different viewing angles are determined at different metastable states. The contact angle of minimum energy among the multiple metastable states is defined as the most stable (equilibrium) contact angle. The Wenzel model is not able to describe the contact angle along the three-phase contact line. The contact angle hysteresis at different drop volumes is determined. The number of the metastable states increases with increasing drop volume. Drop volume effect on the contact angles is also discussed.     

Contact angle hysteresis of microbead suspensions

Microbead suspensions are often used in microfluidic devices for transporting biomolecules. An experimental investigation on the wettability of microbead suspension is presented in this study. The variation in the surface tension and the equilibrium contact angle with the change in the volume fraction of the microbead is presented here. The surface tension of the microbead suspension is measured with the pendant drop technique, whereas the dynamic contact angle measurements, i.e., advancing and receding contact angles, are measured with the sessile drop technique. An equilibrium contact angle of a suspension with particular volume fraction is determined by computing an average over the measured advancing and receding contact angles. It is observed that the surface tension and the equilibrium contact angle determined from advancing and receding contact angles vary with the magnitude of the microbeads volume fraction in the suspension. A decrease in the surface tension with an increase in the volume fraction of the microbead suspension is observed. The advancement and the recession in contact line for dynamic contact angle measurements are achieved with the motorized dosing mechanism. For microbead suspensions, the advancement of the contact line is faster as compared to the recession of the contact line for the same flow rate. The presence of microbeads assists in the advancement and the recession of the contact line of the suspension. A decrease in the equilibrium contact angles with an increase in the microbead suspension volume fraction is observed. Inclusion of microbeads in the suspension increases the wetting capability for the considered combination of the microbead suspension and substrate. Finally, empirical correlations for the surface tension and the contact angle of the suspension as a function of microbead volume fraction are proposed. Such correlations can readily be used to develop mechanistic models for the capillary transport of microbead suspensions related to LOC applications.     

Wetting and absorption of water drops on Nafion films

Water drops on Nafion films caused the surface to switch from being hydrophobic to being hydrophilic. Contact angle hysteresis of >70 degrees between advancing and receding values were obtained by the Wilhelmy plate technique. Sessile drop measurements were consistent with the advancing contact angle; the sessile drop contact angle was 108 degrees . Water drop adhesion, as measured by the detachment angle on an inclined plane, showed much stronger water adhesion on Nafion than Teflon. Sessile water and methanol drops caused dry Nafion films to deflect. The flexure went through a maximum with time. Flexure increased with contact area of the drop, but was insensitive to the film thickness. Methanol drops spread more on Nafion and caused larger film flexure than water. The results suggest that the Nafion surface was initially hydrophobic but water and methanol drops caused hydrophilic sulfonic acid domains to be drawn to the Nafion surface. Local swelling of the film beneath the water drop caused the film to buckle. The maximum flexure is suggested to result from motion of a water swelling front through the Nafion film.     

Microtextured superhydrophobic surfaces: a thermodynamic analysis

Superhydrophobic surfaces with a contact angle (CA) larger than 150 degrees have recently attracted great interest in both academic research and practical applications due to their water-repellent or self-cleaning properties. However, thermodynamic mechanisms responsible for the effects of various factors such as surface geometry and chemistry, liquids, and environmental sources have not been well understood. In this study, a pillar microtexture, which has been intensively investigated in experiments, is chosen as a typical example and thermodynamically analyzed in detail. To gain a comprehensive insight into superhydrophobic behavior, the roles of pillar height, width and spacing (or roughness and solid fraction), intrinsic CA, drop size, and vibrational energy are systematically investigated. Free energy (FE) and free energy barrier (FEB) are calculated using a simple and robust model. Based on the calculations of FE and FEB, various CAs, including apparent, equilibrium (stable), advancing and receding CAs, and contact angle hysteresis (CAH) can be determined. Especially, the design of practical superhydrophobic surfaces is emphasized in connection with the transition between noncomposite and composite states; a criterion for judging such transition is proposed. The theoretical results are consistent with the Wenzel's and the Cassie's equations for equilibrium CA values and experimental observations. Furthermore, based on these results and the proposed criterion, some general principles to achieve superhydrophobic performance are suggested.     

Implementation and examination of a new drop shape analysis algorithm to measure contact angle and surface tension from the diameters of two sessile drops

The performance of a new algorithm developed to measure contact angle and surface tension of sessile drops is examined. To calculate the contact angle and surface tension, the new algorithm (ADSA-TD) requires the radius (contact or equatorial) and volume of two sessile drops of different sizes that are placed on the same surface. Initially, the algorithm was tested using synthetic drops (synthetic or theoretical drops are produced by numerical integration of the Laplace equation). The radii and volumes of synthetic drops were used as ADSA-TD inputs. The calculated contact angle (θ) and surface tension (γ) by ADSA-TD matched perfectly the assumed values of θ and γ used to produce the synthetic drops, confirming theoretically the validity of the new algorithm. In the next step, the sensitivity of the algorithm to input errors was examined. It was shown experimentally that both calculated contact angle and surface tension are affected by the errors in volume and radius. Besides the error in input values, it was shown that the size difference between the paired drops and the differences in their contact angles would affect the output of ADSA-TD. As it turns out, the calculated surface tension is so sensitive to the above factors that ADSA-TD does not appear to be promising as a surface tension measurement technique. However, ADSA-TD produced acceptable contact angle values as compared to measurements made by other proven techniques such as axisymmetric drop shape analysis-profile. Thus, ADSA-TD may be of interest as a contact angle measurement technique which does not require the liquid surface tension as input.