甲醇气相羰基化Ni/AC催化剂的失活行为

采用连续流动固定床反应装置,Ni/AC作为催化剂,在533 K、1.5 MPa、CO/CH3OH/CH3I摩尔比20/19/1、7.5 gcat·h·mol－1下考察了催化剂的稳定性,并通过XPS、ICP和XRD等技术对甲醇气相羰基化反应前后Ni/AC催化剂进行了表征。结果表明,长时间运转催化剂表面形成NiI2,使具有催化活性的Ni0活性中心数量减少,活性降低。XPS结果显示羰基化活性中心Ni不断迁移并在催化剂表面富集,导致积炭效应,堵塞催化剂孔道,使催化剂失活。进一步对积炭类型研究,发现形成的碳物种主要是石墨型碳。Ni向催化剂表面迁移富集,并与CO形成可挥发的Ni(CO)4,造成金属镍的大量流失由ICP所证实。     

甲醇羰基化制乙酸催化剂的研究进展

自70年代初美国采用低压均相溶液法催化甲醇羰基化合成乙酸实现工业化之后,近20年来,世界各国针对这一工艺技术进行丁大量深入的研究与改进。本文就其中催化剂体系的主体金属及其配体或载体选择、反应介质中助催化剂、溶剂与有关添加剂的影响等方面的最新进展和动向,作了综合性介绍和述评。     

甲醇气相羰基化制备乙酸的钴催化剂(YSCo)的研究

甲醇气相羰基化制备乙酸的钴催化剂（ＹＳＣｏ）的研究潘平来，柳忠阳，黄茂开，袁国卿（中国科学院化学研究所，北京１０００８０）关键词甲醇，羰基化，乙酸，钴催化剂通过甲醇羰基化制备乙酸是目前乙酸工业最先进的技术路线．该法与乙烯和乙醇氧化法相比较，无论从原料...     

甲醇气相氧化羰基化合成碳酸二甲酯的研究Ⅲ. 催化剂的失活再生

碳酸二甲酯 (ＤＭＣ)是一种对环境友好的绿色化学品 ,其洁净合成工艺的开发 ,已引起国内外研究者的广泛重视。真田等人[1 ] 对ＰｄＣｌ2 存在下ＣＯ和亚硝酸甲酯反应合成ＤＭＣ过程所用催化剂的失活原因和再生方法进行了研究 ,认为ＰｄＣｌ2 中的Ｃｌ被还原消除生成氯甲酸甲酯导致催化剂失活 ,并发现氯甲酸甲酯在ＤＭＣ合成中可使Ｐｄ催化剂再生和提高寿命。ＤＯＷ公司[2 ] 开发的气相氧化羰基化法催化剂ＣｕＣｌ2-ＫＣｌ ＡＣ易失活 ,该催化剂运行 50～ 1 0 0ｈ后需进行再生。再生时 ,于 1 2 0℃条件下通入 1 0 %ＨＣｌ Ｎ2 混合物 ,再生后…     

一种甲醇直接气相羰基化新催化剂

本世纪７０年代Ｍｏｎｓａｎｔｏ公司成功开发了甲醇液相羰化ＲｈＩ催化体系，使甲醇羰化生产醋酸成为重要的工业过程．然而，由于此工艺产物与催化剂分离复杂、铑资源紧缺以及体系中还必须加大量的碘甲烷（或氢碘酸）作促进剂，设备腐蚀严重．８０年代以来，甲醇气相羰...     

甲醇直接气相羰基化反应动力学

甲醇直接气相羰基化研究 ,是在无任何促进剂下 ,ＣＯ与甲醇直接进行羰基化反应 ,这与目前公认的甲醇必须有碘化物作用下构成催化循环的间接羰化不同 ,在催化理论上有可能提出新的羰基化机理。彭峰等在甲醇直接气相羰基化方面 ,对具有高活性与选择性的非铑非卤素Ｍｏ Ｃ催化剂体系进行了系列研究 ,并取得了较好的实验结果[1～ 5] 。有碘甲烷参与的甲醇羰基化液相或者气相反应 ,大多数文献认为控制步骤是碘化物中Ｃ -Ｉ键的解离及ＣＯ的插入 ,羰基化反应是由一系列平行和连串反应组成的[6～ 8] 。催化剂类型不同得到的动力学参数也不相同 ,难…     

甲醇气相法羰基化合成乙酸的镍催化剂(YhNi)的研究

本文报导了一种新型的甲醇羰基化生产乙酸的镍催化剂.由于选用了由聚偏二氯乙烯热裂解制得的特殊碳化物为载体,所以该催化剂有大比表面积,孔径分布均匀,并有优良的热稳定性和机械强度,其催化甲醇羰基化的速率在相对温和的条件下达到582克乙酸/克镍/时,高于文献报导的镍金属催化剂.     

铜基甲醇合成催化剂的失活研究

选用了两个化肥厂的失活甲醇合成催化剂,采用ＸＲＤ、ＳＥＭ、ＳＥＭ－ＥＤＳ、ＴＥＭ、ＸＰＳ、ＴＲＰ、ＣＯ－ＴＰＤ和化学吸附等方法对催化剂进行比较测试。结果表明,硫中毒、积炭、铜粒长大和杂质金属沉积等是造成甲醇合成催化剂失活的因素。由于某一种或几种因素都导致催化剂活性表面积的降低,对反应物ＣＯ吸附量减少,或造成催化剂对ＣＯ吸附能力的降低,从而降低合成甲醇反应的活性。硫中毒和铜粒长大是普遍存在的最主要因     

钯催化气相氧化羰基化合成碳酸二甲酯

通过催化剂反应性能和反应前后XPS谱图对比，分析了负载型钯催化剂在甲醇气相氧化羰基化合成碳酸二甲酯过程中的失活原因，研究了HCl在维持催化剂活性及失活催化剂再生中的作用．结果表明，氯离子的流失是负载型钯碳催化剂失活的主要原因．由于氯离子的流失，对于PdCl2／AC催化剂，钯很容易从二价变为零价：对于PdCl2-CuCl2／AC催化剂，CuCl2发生变化，失去使钯保持二价氯化物状态的功能．在反应过程中补充HCl可以延长催化剂的寿命，也可以利用HCl对失活催化剂进行再生，但采用HCl不能从根本上解决催化剂失活的问题．     

Ni supported on activated carbon as catalyst for flue gas desulfurization

A series of Ni supported on activated carbon are prepared by excessive impregnation and the desulfurization activity is investigated. It has been shown that the activated carbon-supported Ni is an efficient solid catalyst for flue gas desulfurization. The activated carbon treated by HNO3 exhibits high desulfurization activity, and different amounts of loaded-Ni on activated carbon significantly influence the desulfurization activity. The catalysts are studied by X-ray diffraction (XRD) and X-ray photoelectr...     

Kinetic studies on vapor phase carbonylation of methanol to acetic acid over Rh/Ys catalyst

A novel catalyst Rh/Ys for the carbonylation of methanol to acetic acid with CH3I as the promoter shows excellent activity and selectivity.The reaction is kinetically controlled.The reaction rate is in proportion to the concentration of Rh and CH3I but has nothing to do with those of CH3OHH and CO.The surface active energy is Ea ~51.02 kJ/mol.A mechanism is also proposed.     

甲醇常压气相羰基化碳纳米管负载金属镍催化剂

碳纳注管作为一类纳米级新型碳素材料,具有对反应物质和反应产物的特殊吸咐性能、特殊的孔腔空间立体选择性、碳与金属催化剂的金属-载体强相互作用（SMSI）以及管壁的可改性官能团等优点,近年来,已引起国内外学者的广泛关注。……     

A catalyst for the carbonylation of methanol to acetic acid in gaseous phase

A novel Rh/Ys catalyst for the carbonylation of methanol to acetic acid in gaseous phase is reported. The porous carbon beads (Ys) prepared from the carbonation of poly(vinylidene chloride) were used as the support. This catalyst has a specific surface area of 1 000 m2/g, high mechanical strength and thermal stability. The average diameter of the pore is in the range of 0.8 - 1.2nm. Experimental evidence showed that this catalyst was of high activity and selectivity, which could compare to those of the homogeneous catalyst from Monsanto. The catalytic rate could get to 900 g AcOH/g Rh·h during the carbonylation of methanol to acetic acid. The fine spreading of Ph over the Ys surface is the key factor for the activity.     

氧化铝负载催化剂作用下以甲醇为烷基化试剂的苯酚气相转化制备苯甲醚(英文)

苯甲醚作为重要的化学品和医药中间体而广泛应用于香料、调味剂及有机合成.液相法是传统的苯甲醚制备工艺,例如在碱性环境下,通过酚钠与硫酸二甲酯反应,溴苯与甲醇反应,酚钠与氯代甲烷反应均可制得苯甲醚.然而,这些方法具有环境处理负担较重和所用原料毒性较强等不足而备受限制.因此,环境友好的绿色苯甲醚合成工艺的开发成为必然,苯酚的气相烷基化工艺由此提出.其中,以碳酸二甲酯(DMC)为烷基化试剂的苯酚气相转化苯甲醚制备方法最受关注.DMC是常用的绿色高效烷基化试剂,但其价格相对较高,在一定程度上增加了苯甲醚制备工艺的复杂性和产品成本.鉴于DMC可由甲醇经氧化羰基化制得,因此以甲醇为烷基化试剂的苯酚气相烷基化转化制备苯甲醚方法成为另一研究热点.然而,与DMC的烷基化性能相比,以甲醇为烷基化试剂的反应产物分布较为复杂,作为苯酚O-烷基化(在苯酚的羟基氧原子上发生的烷基化)产物的苯甲醚相对较难获得,而苯酚的C-烷基化(在苯酚的芳环上发生的烷基化)产物甲基酚产率更易提高.总体而言,与DMC烷基化方法相比,以甲醇为烷基化试剂的苯酚气相转化制备苯甲醚方法有待改善,相关反应机理也更欠明晰,因此具有重要的研究价值.本文研究了γ-Al_2O_3(AA)负载型催化剂上以甲醇为烷基化试剂的苯酚气相转化制备苯甲醚方法,考察了反应温度、气体空速、苯酚与甲醇配比以及催化剂中K负载量和焙烧温度等对反应性能的影响,并分析了该体系中的反应机理.研究表明,在AA上负载的8种化合物(NaCl,MgCl_2,Fe_2(SO_4)_3,Co(NO_3)_2,ZnCl_2,La(NO_3)_3,Ce(NO_3)_3和KH_2PO_4)的催化剂中,KH_2PO_4/AA的催化性能最佳,相应催化剂中K离子负载量为7.53 wt%,于700 oC焙烧8 h.苯酚与甲醇气相反应过程中,苯甲醚最大收率出现在400–450 oC,且随甲醇与苯酚的摩尔比升高而增加,但随空速的提高而降低.另外,在KH_2PO_4/AA催化剂的高K含量,以及低温、高空速、低甲醇含量的物料配比的条件下,对苯酚的O-烷基化过程有利.产物除主产物苯甲醚以外,还有少量甲基苯酚、甲基苯甲醚以及二甲基苯酚等副产物.在K含量为7.53 wt%的KH_2PO_4/AA催化剂作用下,苯甲醚收率最高时反应条件为400–450 oC,空速小于0.18 h儃1,甲醇与苯酚摩尔配比为5.本文所开发的催化剂制备方法简单,反应条件温和,产物收率较高,因此具有较好的应用前景.X射线衍射结果显示,经高温焙烧及固相反应后,KH_2PO_4/AA催化剂中产生了K_3Al_2(PO_4)_3新物相.推测该反应机理是酸性氧化铝促进甲醇脱羟基负离子以及K离子促进酚羟基脱氢质子,所形成的甲基正离子进一步与苯氧基负离子结合得到苯甲醚的"钾离子-酸"双功能催化作用过程     

Copper supported on phenanthroline-functionalized porous polymer as an active catalyst for the oxidative carbonylation of methanol

Porous organic polymer has recently attracted tremendous interest because of its potential to combine the best features of homogeneous and heterogeneous catalysts. In this study, copper supported on phenanthroline-functionalized porous polymer (Cu@PCP-Phen) was prepared by a co-polymerization method and used as a heterogeneous catalyst for dimethyl carbonate synthesis via the oxidative carbonylation of methanol. The catalyst was characterized by N₂ adsorption, scanning electron microscopy, transmission electron microscopy, ¹³C solid-state nuclear magnetic resonance, and X-ray photoelectron spectroscopy, which suggested that it possessed a big surface area, hierarchical porous structure, and strong electron-donating effect toward copper species. The Cu@PCP-Phen catalyst showed high catalytic activity, which was significantly higher than those achieved with Cu-based catalysts under similar reaction conditions. In addition, the catalyst can be easily separated and reused at least six times with only a slight decrease in activity. The salient features of this protocol are the simplicity in handling of the catalyst, high catalytic activity, excellent selectivity, low copper leaching, and good catalyst recyclability.     

First application of supported ionic liquid phase (SILP) catalysis for continuous methanol carbonylation

A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)2I2]-[BMIM]I-SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation.     

Synthesis of dimethyl carbonate by vapor phase oxidative carbonylation of methanol over Cu-based catalysts

Dimethyl carbonate (DMC) synthesis reaction by oxidative carbonylation of methanol has been studied using vapor phase flow reaction system in the presence of Cu-based catalysts. A series of Cu-based catalysts were prepared by the conventional impregnation method using activated carbon (AC) as support. The effect of various promoters and reaction conditions on the catalytic reactivities were intensively evaluated in terms of methanol conversion and DMC selectivity. The morphological analysis by X-ray diffraction and SEM was also conducted in order to characterize the emloyed catalysts. Regardless of catalyst compositions, the optimal reaction temperature for oxidative carbonylation of methanol was found to be around 120–130°C. The reaction rate was too slow below 100°C, while too much by-products was produced above 150°C. Among the various catalysts employed, CuCl₂/NaOH/AC catalyst with the molar ratio of OH/Cu=0.5–1.0, has shown the best catalytic performance, which appears to have a strong relationship with the formation of intermediate species, Cu₂(OH)₃Cl.     

Liquid phase carbonylation with solid catalyst Part 2. Carboxymethylation of bromobenzene with group VIII metals supported on active carbon

It was found that palladium supported on active carbon showed high catalytic activities and selectivities for the carbonylation of bromo- and iodobenzene to benzoic acid derivatives in the liquid phase. The carbonylation activity increased with the addition of water to the reaction solvent.