铥、铽及铕离子掺杂的BaAl2O4膜的阴极射线发光特性

利用喷雾热解法合成了Tm、Tb及Eu离子掺杂的铝酸钡(BaAl₂O₄)发光膜,研究了合成条件对其结构和发光特性的影响.在退火温度达到700℃时,生成了BaAl₂O₄膜.Tm³⁺和Tb³⁺掺杂的BaAl₂O₄膜分别发蓝光和绿光,而Eu³⁺掺杂的BaAl₂O₄膜的发光既有Eu²⁺的特征发射——宽的蓝光发射带,也有Eu³⁺的特征发射——窄的红光发射峰.BaAl₂O₄:Tm³⁺的发射主峰位于462nm,在电压为5kV和电流密度为57μA/cm²的条件下,其阴极射线发光(CL)亮度可达25cd/m²,效率可达0.11lm/W.BaAl₂O₄:Tb³⁺的发射主峰位于549nm,在相同的条件下,其阴极射线发光亮度可达120cd/m²,效率可达0.55lm/W.BaAl₂O₄:Eu³⁺的发射主峰位于616nm,其阴极射线发光亮度为50cd/m²,效率为0.23lm/W.BaAl₂O₄:Eu²⁺发蓝光,峰值位于452nm,其阴极射线发光亮度为640cd/m²,效率为2.93lm/W.     

Sr1-xBaxAl2O4：Eu2+ , Dy3+磷光体的 制备及其发光特性

采用高温固相法在1 350 ℃弱还原气氛下制备了Sr_1-xBa_xAl₂O₄ : Eu²⁺ ,Dy³⁺ (x=0,0.2,0.4,0.6,0.8,1.0)长余辉材料,并对其微观结构和发光特性进行了分析。X射线衍射结果表明,当钡的掺杂摩尔分数x＜0.4时,样品晶体结构为SrAl₂O₄单斜晶系结构;当x≥0.4时,样品晶体结构为BaAl₂O₄六角晶系结构;而且随着钡对锶的取代,两种晶体结构的晶格常数都发生了一定程度的膨胀。光致发光测试结果表明,当x从0增大到1.0时,样品发射波长峰值也相应由515 nm逐渐蓝移到494 nm。通过热释光谱测试表明, SrAl₂O₄结构的样品的热释光峰所对应的温度比BaAl₂O₄ 结构的要高,且对应SrAl₂O₄结构的样品的余辉时间更长,初始亮度更高。     

Y2O3: Eu,Dy的制备与红色长余辉发光性能研究

采用高温固相法合成发光样品Y₂O₃：Eu³⁺_0.01和Y₂O₃：Eu³⁺_0.01,Dy³⁺_0.01.X射线衍射分析(XRD)表明样品保持Y₂O₃晶格结构,掺入的Eu³⁺和Dy³⁺对Y_{2关键词： 长余辉 2}O₃')" href="#">Y₂O₃ 稀土掺杂 陷阱     

Absorption Spectra of Single Crystals of EuGa2S4 and EuGa2S4:Co

The optical properties of EuGa₂S₄ and EuGa₂S₄:Co single crystals in a range of temperatures from 77 to 300 K are investigated. The single crystals are obtained by the Bridgman method and are characterized by tetragonal syngony. The behavior of the optical transitions in the photon energy range 1.70–2.45 eV and the temperature range 77–300 K is determined. It is established that in the energy range 1.77–1.90 eV absorption is associated with transitions of the Co²⁺ ion, while in the range 2.20–2.40 eV, with indirect allowed optical transitions.     

SrO/Al2O3比率对Sr2AlO4:Eu,Dy发光性能的影响

采用高温固相法合成稀土离子掺杂碱土铝酸盐发光粉,通过改变原料配比分别合成出富Sr和富Al的Sr2AlO4：Eu,Dy发光粉样品。XRD分析结果表明,SrO／Al2O3比率的微小变化不会影响样品的晶相组成。样品的发光性能和长余辉特性测试结果表明,富Al的Sr2AlO4：Eu,Dy发光粉具有较高的荧光强度及较长的余辉时间,说明Sr2AlO4晶格中SrO／Al2O3比率对Sr2AlO4：Eu,Dy发光性能和长余辉特性有很大的影响。激发与发射光谱、发射峰余辉衰减以及热释光谱分析表明,SrO／Al2O3比率的微小变化,导致晶格中发光中心Eu^2 浓度和陷阱的深度与密度发生改变。在富Sr体系中,稀土掺杂离子Eu^2 ,Dy^3 较难进入Sr^2 的晶格位置,晶格中发光中心Eu^2 浓度和陷阱密度都较低,使得粉体发光强度较低,余辉时间较短。     

尿素用量对燃烧法合成CaAl2O4：Eu2+,Nd3+长余辉材料发光性能的影响

利用金属硝酸盐和尿素的氧化还原反应,通过燃烧法在600℃的炉温下合成了蓝紫色长余辉发光材料CaAl₂O₄:Eu²⁺,Nd³⁺。在金属硝酸盐溶液浓度不变的条件下,通过改变尿素与硝酸根的量的比,合成了多组长余辉材料样品。当尿素用量较少时,Eu³⁺不能完全被还原为Eu²⁺;随尿素用量增加,样品的Eu³⁺特征发射减弱,余辉初始亮度和持续时间均得到改善;当尿素的用量达到理论用量的5倍时,样品余辉特性最好,继续增加尿素用量,余辉亮度和持续时间反而下降。将燃烧法制备的各组样品用活性炭密封,在1000℃条件下反应2h,使Eu³⁺完全被还原为Eu²⁺,同时除去燃烧法反应不完全的杂质,可以一定程度提高材料的余辉发光性能。     

Y2O2S:Eu3+,Mg2+,Ti4+红色材料的制备和长余辉性能

用高温固相法制备了Y2O2S：Eu^3 ,Mg^2 ,Ti^4 红色长余辉材料,余辉时间达到1h以上,X射线衍射测量表明材料的晶体结构为Y2O2S。发射光谱对应了Eu^3 离子^5DJ(J=0,1,2,3)→^7FJ(J=0,1,2,3,4))的特征发射;激发光谱主峰位于345nm,另外在260,396,468,540nm等处也存在激发峰。对比测量了Y2O2S：Eu^3 ,Mg^2 ,Ti^4 和Y2O2S:Eu^3 的热释发光曲线,Y2O2S:Eu^3 的热释发光曲线可以拟合成3个热释发光峰的叠加：237,226,301K;而Y2O2S：Eu^3 ,Mg^2 ,Ti^4 的热释发光曲线可以拟合成5个热释发光峰的叠加：149,215,262,287,334K,并计算了相应的陷阱能级。Ti^4 是引起较深陷阱能级的主要原因,Mg^2 起电荷补偿的作用。     

Sr0.6Ba0.2Ca0.2Al2O4 ∶Eu,Dy的制备与长余辉发光性能研究

采用高温固相法制备了Ca,Ba共掺的Sr_0.6Ba_0.2Ca_0.2Al₂O₄ ∶Eu²⁺_0.01, Dy³⁺_0.02和单掺Ba的Sr_0.6Ba_0.4Al₂O₄ ∶Eu²⁺_0.01, 关键词： 长余辉 铝酸锶 稀土掺杂 陷阱能级     

Eu3+摩尔浓度对Y2O2S:Eu3+,Mg2+,Ti4+红色长余辉材料光谱的影响

用高温固相法制备了Y2O2S：Eu^3 ,Mg^2 ,Ti^4 红色长余辉材料。测量了该材料的余辉曲线,余辉时间为1h以上;由X射线衍射得到晶体结构为Y2O2S.测量了不同Eu^3 摩尔浓度下的激发光谱和发射光谱,得到从^5DJ(J=0,1,2,3)^-7FJ(J=0,1,2,3,4,5)的发射谱线,并得到位于260,345,468和540nm激发峰。由于激活剂饱和效应,Y2O2S：Eu^3 ,Mg^2 ,Ti^4 发射光谱中513．6,540．1,556．4,587．3和589．3nm属于从^5D2,^5D1到^7FJ(J=0,1,2,3,4)跃迁的发射峰随Eu^3 摩尔浓度的增加相对削弱;激发谱包括位于350nm左右属于电荷转移态吸收(Eu^3 -O^2-,Eu^3 -S^2 )的激发主峰和在可见光区位于468,520和540nm属于Eu^3 离子4f-4厂吸收的激发峰。随着Eu^3 摩尔浓度的增加,位于468,520和540nm的激发峰相对增强。     

Spectroscopy study of SrAl2O4:Eu3+

Computational and experimental method is employed to study optical properties SrAl₂O₄ induced by europium dopant. Atomistic modeling is used to predict the doping sites and charge-compensation schemes for SrAl₂O₄:Eu systems and also to calculate the symmetry and the detailed geometry of the dopant site. This information is then used to calculate the crystal field parameters. SrAl₂O₄ doped with europium were prepared via a sol–gel proteic methodology. The photoluminescence experiments were performed at room temperature and at 13 K. The transition energy for the Eu³⁺-doped material is compared to the theoretical results. Based on Judd-Ofelt approach, the intensity parameters Ω_2,4 of Eu³⁺ in the SrAl₂O₄ matrix were calculated.     

(Eu2+,Nd3+)∶CaAl2O4的长余辉发光及机理的研究

采用高温固相反应法制备了Eu^2 ∶CaAl2O4、（Eu^2 ,Nd^3 )∶CaAl2O4，等系列材料。测量了其激发、发射光谱及余辉衰减曲线。分析了掺杂稀土离子对长余辉发光的作用。并对其发光机理进行了深入地探讨。     

Energy transfer between Eu3+ ions in a lattice with two different crystallographic sites: Y2O3:Eu3+, Gd2O3:Eu3+ and Eu2O3

The Eu³⁺ ion occupies two different crystallographic sites in (Y_1−xEu_x)₂O₃ and (Gd_1−xEu_x)₂O₃, with site symmetry S₆ and C₂. Energy transfer over more than 7 Å occurs from Eu³⁺ (S₆) ions to Eu³⁺ (C₂) ions. This is shown to be a direct one-phonon assisted process, in combination with a one-site resonant two-phonon assisted process at higher temperatures. For x = 1 there is energy migration over the Eu³⁺ (C₂) sublattice to quenching impurities. The presence of cooperative absorption points to superexchange interaction between the Eu³⁺ ions.     

SrGa2O4:Eu的合成及其发光性能

采用固相反应法合成了掺杂Eu3 离子的SrGa2O4,用X射线粉末衍射对其结构进行了表征。XRD数据经计算机处理表明:SrGa2O4属单斜晶系,晶胞参数a=0.943nm,b=0.900nm,c=0.839nm,β=89.06°,属P21/c(No.14)空间群。测定了激发光谱和发射光谱,光谱数据表明:SrGa2O4:Eu3 荧光粉的发射主峰在610nm,证明Eu3 离子占据了非反演对称中心的位置。在掺杂Eu3 离子摩尔分数大于1%时,由于晶体场的影响,位于590,610nm附近的2个发射峰均出现劈裂现象,即有2个5D0→7F1(586,597nm)和2个5D0→7F2(609,615nm)发射峰,7F2劈裂出两个分支的强度比例随Eu3 浓度的变化而变化。     

Ga3S2-和Ga4S3-团簇结构及性质的密度泛函理论研究

采用密度泛函理论（DFT）中的B3LYP方法和BP86方法,对Ga₃S₂^-团簇和Ga₄S₃^-团簇进行结构优化,并计算和分析了最稳定结构的成键性质及振动特性.计算结果表明,Ga₃S₂^-团簇和Ga₄S₃^-团簇的最稳定结构是由"Ga-S-Ga"结构单元和处于端位的"Ga-S"结构单元组成的.键级分析表明上述两结构单元都具有较强的稳定性.此外,通过分析红外振动光谱数据也发现在"Ga-S-Ga"单元和"Ga-S"单元处有红外强峰出现.     

CaAl2O4:Eu2+,Nd3+纳米粉体的合成与发光性质

采用溶胶-凝胶法制备了CaAlO4：Eu^2＋,Nd^3＋纳米粉体发光材料。利用DTA,TG,XRD,SEM,光谱分析等手段对样品进行了结构和性能分析。实验结果表明,800℃烧结的样品形成已CaAl2O4晶相,样品平均晶粒尺寸为20～40nm,与CaAlO4：Eu^2＋,Nd^3＋粗晶材料相比,样品的发光光谱发生了“蓝移”,热释光峰值向高温移动了96℃,且曲线形状变宽,发光衰减是由初始的快衰减和随后的慢衰减构成,发光余辉时间5h。     

新型红色荧光粉NaLa_(0.7)(MoO_4)_(2-x)(WO_4)_x∶0.3Eu~(3+)的制备及发光性质研究

采用高温固相法合成具有余辉性能的发光材料NaLa_(0.7)(MoO_4)_(2-x)(WO_4)_x∶0.3Eu~(3+)(x=0,0.5,1,1.5,2)。用X射线衍射(XRD)和荧光光谱对样品的晶体结构和发光特性进行表征。测试结果表明,在900℃下烧结8 h所合成的NaLa_(0.7)(MoO_4)_(2-x)(WO_4)_x∶0.3Eu~(3+)样品为纯相Na La(Mo O_4)_2,样品可被近紫外光393nm和蓝光462 nm有效激发,其发射主峰位于615 nm处,属于Eu3+的5D0-7F2跃迁。Na La_(0.7)(Mo O_4)_(2-x)-(WO_4)_x∶0.3Eu~(3+)的发光强度随着W6+浓度的增加而增大,当W6+掺杂量x=1时发光最强,而后随W6+掺杂浓度的增加出现浓度猝灭现象。通过计算得到样品在393 nm和462 nm激发下的色坐标,当W6+的掺杂量x=1时,样品的红光色纯度最好。     

Eu~(3+)掺杂浓度及基质氧空位对Ca~(2-x)Eu_xSnO_4发光性能的影响

采用高温固相法制备Ca_(2-x)SnO_4:xEu~(3+)(x=0,0.001,0.005,0.01,0.015,0.02)发光材料,分别在空气和真空氛围中进行烧结,研究Eu3+掺杂浓度及基质中氧空位对样品发光性能的影响。随着Eu~(3+)离子浓度的增加,发射强度呈逐渐增大的趋势,主发射峰由两个分别位于614 nm和618 nm的峰逐步合为一个位于616nm的发射峰。在Ca_(2-x)SnO_4∶xEu~(3+)样品的激发光谱中,存在着200~295 nm的Eu~(3+)-O~(2-)电荷迁移带,随着Eu~(3+)离子浓度的增加,电荷迁移带的峰位由271 nm红移到286 nm。此外,在Eu~(3+)离子掺杂浓度相同的情况下,真空中烧结得到样品的发光强度是空气中烧结得到样品的2倍。这是由于在真空氛围中烧结产生的氧空位增加使得传导电子密度升高,导致发光强度增加。而且,氧空位的增加导致电子陷阱的增多,这使得Ca_(2-x)SnO_4∶xEu~(3+)样品的余辉性能得到了很大程度的提高。     

Eu,Dy共掺杂SrAl2O4长余辉材料制备新工艺

活化Al-Sr合金粉末水解制备SrAl₂O₄长余辉材料的前驱体,并采用高温固相反应法制备出Eu,Dy共掺杂的SrAl₂O₄长余辉材料,对其微观结构和发光特性进行了研究。实验结果表明:前驱体中Al、Sr元素在微观状态下分布均匀,所制成的长余辉发光材料的发射主峰位于520nm附近,为典型的Eu²⁺离子4f5d-4f的特征发射,初始亮度达到18cd/m²,余辉时间长达46h。     

Luminescence spectroscopy of Eu3+ and Mn2+ ions in MgGa2O4 spinel

Photoluminescence and excitation spectra of the spinel-type MgGa₂O₄ with 0.5 mol. % Mn²⁺ ions and Eu³⁺ content from 0 to 8 mol. % have been investigated in this work at room temperature. Polycrystalline samples were synthesized via high-temperature solid-state reaction method. Photoluminescence spectra of all samples exhibit host emission presented by a broad “blue” band peaking ∼430 nm, which consists of at least three elementary bands that correspond to different host defects. Excitation of the host luminescence showed the broad band with a maximum at 360 nm. Characteristic bands of d–d transitions of Mn²⁺ ions and f–f transitions of Eu³⁺ ions together with charge-transfer bands (CTB) of these ions were also found on the excitation spectra. Mn²⁺ and Eu³⁺ co-doped samples emit in green and red spectral regions. Mn²⁺ ions are responsible for the green emission band at 505 nm (⁴Т₁→⁶А₁ transition). The studies of photoluminescence spectra of activated samples with different Eu³⁺ ions content show characteristic f–f luminesecence of Eu³⁺ ions. The maximum of Eu³⁺ emission was found at 618 nm (⁵D₀→⁷F₂) and optimal concentration of activator ions was around 4 mol. %.     

纳米Gd2O3中两种格位Eu3+的电荷迁移态激发跃迁

观测了粒径分别为15,23,135m的立方相Gd2O3：Eu^3 的选择激发光谱、发射光谱和激发光谱。受强量子限域效应的影响,纳米Gd2O3：Eu^3 的激发光谱的强度表现出对颗粒尺寸的明显依赖性。用Jorgensen公式计算电荷迁移带的位置,与实验测得激发光谱中位置相一致。通过电荷迁移带不同位置的选择激发光谱可以分辨出立方相Gd2O3：Eu^3 中C2和S6格位Eu^3 的发光,从选择激发的发射光谱和激发光谱结果计算出C2和S6格位电荷迁移带的激发光谱,与实验结果相符合。