Electron density profile at the interface of SiO2/Si(0 0 1)

In this report we present grazing incidence X-ray reflectivity (GIXR) study of SiO₂/Si(0 0 1) system. We have analysed the X-ray reflectivity data using recursive formalism based on matrix method and distorted wave Born approximation (DWBA). From the analysis of the reflectivity data we could obtain the electron density profile (EDP) at the interface of the dielectric SiO₂ film and the Si(0 0 1) substrate. The EDP obtained from the matrix method follows the DWBA scheme only when two transition layers are considered at the interface of SiO₂/Si. The layer which is in proximity with the Si substrate has a higher electron density value than the Si and SiO₂ values and it appears as a maximum in the EDP. The layer which is in proximity with the dielectric SiO₂ layer has an electron density value lower than the SiO₂ value and it appears as a minimum in the EDP. When the thickness of the SiO₂ layer is increased the lower density layer diminishes and the higher density layer persists.     

Cooperative growth of nano-islands on Si(1 0 0) surface

By setting up two low temperature regions on a terrace of a vicinal Si(1 0 0)-2 × 1 surface, we have studied growth of nano-islands in the two regions using a kinetic Monte Carlo simulation. At first two islands are formed and grow independently without any supply of atoms from the outside. As the growth proceeds further, two islands are connected with each other by forming a bridge region. After the connection, the growth changes dramatically showing a competitive mode in one stage and a cooperative mode in the other. Two islands grow cooperatively in a sense that a larger island ceases to grow and waits until the size of the other smaller island becomes similar to that of the larger one. When two islands become similar in size, one of the islands grows faster than the other competitively, by accumulating atoms from then smaller one. The origin of the growth mode is analyzed.     

Thermal stability of atomic-layer-deposited ultra-thin niobium oxide film on Si (1 0 0)

Ultra-thin Nb₂O₅ films with excellent uniformity have been grown on Si (1 0 0) by atomic-layer-deposition using Nb(OC₂H₅)₅ and H₂O precursors, and the corresponding thermal stability has been studied through atomic force microscope, transmission electron microscope and X-ray photoelectron spectroscopy. The results indicate that the ultra-thin (∼3 nm) Nb₂O₅ film is gradually built up into distributed large islands with increasing rapid thermal annealing (RTA) temperature. Meanwhile, both crystalline and amorphous phases are formed in the matrix of Nb₂O₅ annealed at 700 °C. In terms of the as-prepared sample, an interfacial layer (IL) with a thickness of around 1.5 nm is observed, that is composed of niobium silicate (Nb-O-Si). Further, the high temperature RTA leads to a thickened IL, which is attributed to the formation of more Nb-O-Si bonds and new silicon oxide (Si-O-Si) adjacent to the Si (1 0 0).     

Growth of oriented crystalline Ag nanoislands on air-exposed Si(0 0 1) surfaces

Growth of Ag islands under ultrahigh vacuum condition on air-exposed Si(0 0 1)-(2 × 1) surfaces has been investigated by in-situ reflection high energy electron diffraction (RHEED). A thin oxide is formed on Si via exposure of the clean Si(0 0 1)-(2 × 1) surface to air. Deposition of Ag on this oxidized surface was carried out at different substrate temperatures. Deposition at room temperature leads to the growth of randomly oriented Ag islands while well-oriented Ag islands, with (0 0 1)_Ag||(0 0 1)_Si, [1 1 0]_Ag||[1 1 0]_Si, have been found to grow at substrate temperatures of ≥350 °C in spite of the presence of the oxide layer between Ag islands and Si. The RHEED patterns show similarities with the case of Ag deposition on H-passivated Si(0 0 1) surfaces.     

Fabrication of nanostructures by selective growth of C60 and Si on Si(1 1 1) substrate

Using two types of selective growth, selective C₆₀ growth and selective Si growth, on a common Si(1 1 1) substrate, an array of C₆₀ nanoribbons with controlled values of width and thickness is fabricated. On a surface that has Si(1 1 1)√3 × √3R30°-Ag (referred to as Si(1 1 1)√3-Ag hereafter) and bare Si(1 1 1) regions at the same time, the preferential growth of C₆₀ multilayered film is recognized on the Si(1 1 1)√3-Ag region. The growth of Si selectively occurs on a bare Si(1 1 1) region if the substrate surface has C₆₀-adsorbed and bare Si(1 1 1) regions at the same time. As a demonstration of the use of these selective growths, we fabricate an array of well-isolated C₆₀ nanoribbons, which show a well-ordered molecular arrangement and have sizes of about 40 nm in widths and 3-4 nm in thicknesses.     

Ga-induced superstructures on the Si(1 1 1) 7 × 7 surface

Monolayer Ga adsorption on Si surfaces has been studied with the aim of forming p-delta doped nanostructures. Ga surface phases on Si can be nitrided by N₂⁺ ion bombardment to form GaN nanostructures with exotic electron confinement properties for novel optoelectronic devices. In this study, we report the adsorption of Ga in the submonolayer regime on 7 × 7 reconstructed Si(1 1 1) surface at room temperature, under controlled ultrahigh vacuum conditions. We use in-situ Auger electron spectroscopy, electron energy loss spectroscopy and low energy electron diffraction to monitor the growth and determine the properties. We observe that Ga grows in the Stranski-Krastanov growth mode, where islands begin to form on two flat monolayers. The variation in the dangling bond density is observed during the interface evolution by monitoring the Si (LVV) line shape. The Ga adsorbed system is subjected to thermal annealing and the residual thermal desorption studied. The difference in the adsorption kinetics and desorption dynamics on the surface morphology is explained in terms of strain relaxation routes and bonding configurations. Due to the presence of an energetic hierarchy of residence sites of adatoms, site we also plot a 2D phase diagram consisting of several surface phases. Our EELS results show that the electronic properties of the surface phases are unique to their respective structural arrangement.     

Si epitaxial growth on LaAlO3(0 0 1)

We report on the growth of Si on c(2 × 2) reconstructed LaAlO₃(0 0 1) surfaces at high substrate temperature (700 °C) by molecular beam epitaxy. An initial Volmer-Weber mode is evidenced using reflection high energy electron diffraction (RHEED), X-ray photoelectron diffraction (XPD) and atomic force microscopy. After the deposition of a few monolayers, the islands coalesce. Using X-ray photoelectron spectroscopy, we demonstrate that Si islands exhibit an abrupt interface with the LaAlO₃ substrate without formation of silicate or silica. Finally, combined RHEED and XPD measurements show the epitaxial growth of Si with a unique Si(0 0 1)//LaAlO₃(0 0 1) and Si<1 0 0>//LAO<1 1 0> relationship.     

Molecular dynamics simulation of CH3 interaction with Si(1 0 0) surface

Molecular dynamics simulations of the CH₃ interaction with Si(1 0 0) were performed using the Tersoff-Brenner potential. The H/C ratio obtained from the simulations is in agreement with available experimental data. The results show that H atoms preferentially react with Si. SiH is the dominant form of SiH_x generated. The amount of hydrogen that reacts with silicon is essentially energy-independent. H atoms do not react with adsorbed carbon atoms. The presence of C-H bonds on the surface is due to molecular adsorption.     

Influence of patterning on the nucleation of Ge islands on Si and SiO2 surfaces

Surface patterning is expected to influence the nucleation site of deposited nanostructures. In the present study, clean Si and SiO₂ surfaces were patterned by a nanolithographic process using a Focused Ion Beam (FIB). Ge was evaporated in ultra high vacuum at 873 K on these substrates, resulting in the formation of island arrays. Based on scanning tunneling microscopy and atomic force microscopy images, a statistical analysis was performed in order to highlight the effect of patterning on the size distribution of islands compared to a non-patterned surface. We find that the self-organization mechanism on patterned substrates results in a very good arrangement and positioning of Ge nanostructures, depending on growth conditions and holes distance, both on Si and SiO₂ surfaces.     

Formation of strontium template on Si(1 0 0) by atomic layer deposition

The formation of ordered Sr overlayers on Si(1 0 0) by Atomic Layer Deposition (ALD) from bis(triisopropylcyclopentadienyl) Strontium (Sr(C₅ⁱPr₃H₂)₂) and H₂O has been investigated. SrO overlayers were deposited on a 1-2 nm SiO₂/Si(1 0 0) substrate, followed by a deoxidation process to remove the SiO₂ layer at high temperatures. Auger electron spectroscopy, Rutherford backscattering spectrometry, spectroscopic ellipsometry, and low-energy electron diffraction were used to investigate the progress of both ALD and deoxidation processes. Results show that an ordered Sr/Si(1 0 0) surface with 2 × 1 pattern can be obtained after depositing several monolayers of SrO on Si using ALD followed by an anneal at 800-850 °C. The (2 × 1) ordered Sr/Si(1 0 0) surface is known to be an excellent template for the epitaxial growth of SrTiO₃ (STO) oxide. The present results demonstrate that ALD is a potential alternative to molecular beam epitaxy methods for the fabrication of epitaxial oxides on semiconductor substrates.     

SiO adsorption on a p(2 × 2) reconstructed Si(1 0 0) surface

We have investigated the adsorption mechanism of SiO molecule incident on a clean Si(1 0 0) p(2 × 2) reconstructed surface using density functional theory based methods. Stable adsorption geometries of SiO on Si surface, as well as their corresponding activation and adsorption energies are identified. We found that the SiO molecule is adsorbed on the Si(1 0 0) surface with almost no activation energy. An adsorption configuration where the SiO binds on the channel separating the dimer rows, forming a Si-O-Si bridge on the surface, is the energetically most favourable geometry found. A substantial red-shift in the calculated vibrational frequencies of the adsorbed SiO molecule in the bridging configurations is observed. Comparison of adsorption energies shows that SiO adsorption on a Si(1 0 0) surface is energetically less favourable than the comparable O₂ adsorption. However, the role of SiO in the growth of silicon sub-oxides during reactive magnetron plasma deposition is expected to be significant due to the relatively large amount of SiO molecules incident on the deposition surface and its considerable sticking probability. The stable adsorption geometries found here exhibit structural properties similar to the Si/SiO₂ interface and may be used for studying SiO_x growth.     

Transient-enhanced Si diffusion on natural-oxide-covered Si(0 0 1) nano-structures during vacuum annealing

The morphology of annealed patterned Si(0 0 1) wire templates was studied by several techniques. We found an enormous Si-mass transport on the Si surface at usual oxide desorption temperatures around 900°C under UHV conditions. Heat treatment of 5 min transforms the initially rectangular wire profiles with a height of 300 nm to flat (<100 nm) and faceted triangular ridges exhibiting thermodynamically preferred {1 1 1}- and {3 1 1}-facets.It was found that the natural SiO₂ on the predefined wire pattern must be responsible for the degradation of the wire structure. Removing the SiO₂ layer from the Si wires ex situ with an HF dip preserves the rectangular structures during high-temperature annealing. The Si–SiO₂ interface was investigated with high-resolution transmission electron microscopy to image the Si wire surface and the natural oxide layer in detail.     

Properties of thick SiO2/Si structure formed at 120 °C by use of two-step nitric acid oxidation method

Thick (i.e., ∼10 nm) SiO₂/Si structure has been formed at 121 °C by immersion of Si in relatively low concentration HNO₃ followed by that in 68 wt.% HNO₃ (i.e., two-step nitric acid (HNO₃) oxidation method of Si, NAOS) and spectroscopic properties and electrical characteristics of the NAOS SiO₂ layers are investigated. The SiO₂ thickness strongly depends on the concentration of HNO₃ aqueous solutions employed in the initial oxidation, and it becomes the largest at the HNO₃ concentration of 40 wt.%. The MOS diodes with the ∼9 nm SiO₂ layer formed by the NAOS method possess a relatively low leakage current density (e.g., 10⁻⁸ A/cm² at the forward bias of 1 V) and it is further decreased by more than one order of magnitude by post-metallization annealing (PMA) in hydrogen at 250 °C. The good leakage characteristic is attributable to atomically flat SiO₂/Si interfaces and high atomic density of 2.30-2.32 × 10²² atoms/cm³ of the NAOS SiO₂ layers. High-density interface states are present in as-prepared SiO₂ layers and they are eliminated by PMA in hydrogen.     

The changes in morphology of Si(1 0 0) surface upon dipping in ultrapure water

The changes in morphology and chemical states of Si(1 0 0) surface upon dipping in ultrapure water were investigated by using atomic force microscope and X-ray photoelectron spectroscopy. The oxidation and the etching competitively progressed at the HF-treated Si(1 0 0) surface in ultrapure water, which made the smooth surface rough. However, the surface covered with a thick native oxide film was not etched at all. During the repetition of the oxidation and the etching, the SiO₂-nuclei was, by chance, able to grow up to some size of islands and worked as the protective barrier against the water etching. Thus, the SiO₂-islands would remain without being etched off, whereas rest parts of the surface could be etched off. This selective etching leads the surface morphology to become rough. Both the oxidation and the etching progressed violently as the water temperature and the dipping time increased.     

New tetramer structures in the initial process of Si homoepitaxial growth on Si (0 0 1)

We have studied the interaction between Si ad-dimers in the initial process of Si homoepitaxial growth on Si (0 0 1) surface by molecular dynamics simulations using the Stillinger-Weber potential. The interactions determine the formation of larger clusters from diffusing dimers. We show different pathways for the formation of multiple-dimer clusters and propose two new tetramer structures (T_BB and T_CC) formation by two diffusing dimers interacting. These tetramer structures have been found to be energetically stable with respect to isolated ad-dimers. Moreover, their local bonding configuration is very similar to the B-type step edge which is known to be the favored adsorption site for epitaxial growth. The proposed tetramers may play a crucial role as the nucleus of the new epitaxial layer on Si (0 0 1).     

Bimodal growth of manganese silicide on Si(1 0 0)

Two different growth modes of manganese silicide are observed on Si(1 0 0) with scanning tunneling microscopy. 1.0 and 1.5 monolayer Mn are deposited at room temperature on the Si(1 0 0)-(2 × 1) substrate. The as-grown Mn film is unstructured. Annealing temperatures between room temperature and 450 °C lead to small unstructured clusters of Mn or Mn_xSi_y. Upon annealing at 450 °C and 480 °C, Mn reacts chemically with the Si substrate and forms silicide islands. The dimer rows of the substrate become visible again. Two distinct island shapes are found and identified as MnSi and Mn₅Si₃.     

Effects of electronic confinement and substrate on the low-temperature growth of Pb islands on Si(1 0 0)-2 × 1 surfaces

The growth of Pb films on the Si(1 0 0)-2 × 1 surface has been investigated at low temperature using scanning tunneling microscopy. Although the orientation of the substrate is (1 0 0), flat-top Pb islands with (1 1 1) surface can be observed. The island thickness is confined within four to nine atomic layers at low coverage. Among these islands, those with a thickness of six layers are most abundant. Quantum-well states in Pb(1 1 1) islands of different thickness are acquired by scanning tunneling spectroscopy. They are found to be identical to those taken on the Pb(1 1 1) islands grown on the Si(1 1 1)7 × 7 surface. Besides Pb(1 1 1) islands, two additional types of Pb islands are formed: rectangular flat-top Pb(1 0 0) islands and rectangular three-dimensional (3D) Pb islands, and both their orientations rotate by 90° from a terrace to the adjacent one. This phenomenon implies that the structures of Pb(1 0 0) and 3D islands are influenced by the Si(1 0 0)-2 × 1 substrate.     

The corrosion behavior of intermetallic compounds Ni3(Si,Ti) and Ni3(Si,Ti) + 2Mo in acidic solutions

The corrosion behavior of the intermetallic compounds homogenized, Ni₃(Si,Ti) (L1₂: single phase) and Ni₃(Si,Ti) + 2Mo (L1₂ and (L1₂ + Ni_ss) mixture region), has been investigated using an immersion test, electrochemical method and surface analytical method (SEM; scanning electron microscope and EPMA: electron probe microanalysis) in 0.5 kmol/m³ H₂SO₄ and 0.5 kmol/m³ HCl solutions at 303 K. In addition, the corrosion behavior of a solution annealed austenitic stainless steel type 304 was studied under the same experimental conditions as a reference. It was found that the intergranular attack was observed for Ni₃(Si,Ti) at an initial stage of the immersion test, but not Ni₃(Si,Ti) + 2Mo, while Ni₃(Si,Ti) + 2Mo had the preferential dissolution of L1₂ with a lower Mo concentration compared to (L1₂ + Ni_ss) mixture region. From the immersion test and polarization curves, Ni₃(Si,Ti) + 2Mo showed the lowest corrosion resistance in both solutions and Ni₃(Si,Ti) had the highest corrosion resistance in the HCl solution, but not in the H₂SO₄ solution. For instance, it was found that unlike type 304 stainless steel, these intermetallic compounds were difficult to form a stable passive film in the H₂SO₄ solution. The results obtained were explained in terms of boron segregation at grain boundaries, Mo enrichment and film stability (or strength).     

Effect of laser annealing on crystallinity of the Si layers in Si/SiO2 multiple quantum wells

We report on continuous-wave laser induced crystallisation processes occurring in Si/SiO₂ multiple quantum wells (MQW), prepared by remote plasma enhanced chemical vapour deposition of amorphous Si and SiO₂ layers on quartz substrates. The size and the volume fraction of the Si nanocrystals in the layers were estimated employing micro-Raman spectroscopy. It was found that several processes occur in the Si/SiO₂ MQW system upon laser treatment, i.e. amorphous to nanocrystalline conversion, Si oxidation and dissolution of the nanocrystals. The speed of these processes depends on laser power density and the wavelength, as well as on the thickness of Si-rich layers. At optimal laser annealing conditions, it was possible to achieve ∼100% crystallinity for 3, 5 and 10 nm thickness of deposited amorphous Si layers. Crystallization induced variation of the light absorption in the layers can explain the complicated process of Si nanocrystals formation during the laser treatment.     

Scaling behavior of island density in submonolayer growth of CaF2 on vicinal Si(1 1 1)

We have studied the scaling behavior of two-dimensional island density during submonolayer growth of CaF₂ on vicinal Si(1 1 1) surfaces using scanning tunneling microscopy. We have analyzed the morphology of the Si(1 1 1) surfaces where CaF₂ partial monolayers with coverages of about 0.1 monolayer are deposited at ∼600 °C. The number density of terrace nucleated islands increases with substrate terrace width l as ∼l⁴ in a low island density regime. This scaling behavior is consistent with predictions for the case of the irreversible growth of islands.