Effect of the phase states of self-assembled monolayers on pentacene growth and thin-film transistor characteristics

To investigate the effects of the phase state (ordered or disordered) of self-assembled monolayers (SAMs) on the growth mode of pentacene films and the performance of organic thin-film transistors (OTFTs), we deposited pentacene molecules on SAMs of octadecyltrichlorosilane (ODTS) with different alkyl-chain orientations at various substrate temperatures (30, 60, and 90 degrees C). We found that the SAM phase state played an important role in both cases. Pentacene films grown on relatively highly ordered SAMs were found to have a higher crystallinity and a better interconnectivity between the pentacene domains, which directly serves to enhance the field-effect mobility, than those grown on disordered SAMs. Furthermore, the differences in crystallinity and field-effect mobility between pentacene films grown on ordered and disordered substrates increased with increasing substrate temperature. These results can be possibly explained by (1) a quasi-epitaxy growth of the pentacene film on the ordered ODTS monolayer and (2) the temperature-dependent alkyl chain mobility of the ODTS monolayers.     

A Chiral Self‐Assembled Monolayer Derived from a Resolving Agent and its Performance as a Crystallization Template for an Organic Compound from Organic Solvents

A new chiral nonracemic thiol derived from a popular acidic resolving agent that incorporates a cyclic disubstituted phosphate group (phencyphos) has been prepared in enantiomerically pure form. The stereochemistry and absolute configuration were established by performing a single‐crystal X‐ray structural analysis of a synthetic intermediate. The thiol compound was used for the preparation of self‐assembled monolayers (SAMs) on both monocrystalline and polycrystalline metallic gold, which have very different surface roughness. The monolayers were used to promote the nucleation and growth of crystals from nonaqueous solutions of an organic molecule (the parent phencyphos) of similar structure to the compound present in the monolayer. The template layers influence the nucleation and growth of the phencyphos crystals despite the lack of two‐dimensional order in the surfaces. Heterogeneous nucleation of phencyphos takes place upon evaporation of either CHCl₃ or isopropanol solutions of the compound on the SAM surfaces, where the evaporation rate merely influences the size and homogeneity of the crystals. The roughness of the surface also plays an important role; the polycrystalline gold produces more homogeneous samples because of the greater number of nucleation sites. Clear evidence for nucleation and growth on the surfaces is shown by scanning electron microscopy. The variation in crystal form achieved by using different surfaces and solvents suggests that the layers are applicable for the preparation of organic crystals from organic solutions.     

Molar mass dependent growth of poly(epsilon-caprolactone) crystals in Langmuir films

Poly(epsilon-caprolactone) (PCL) samples with number average molar masses (Mn) ranging from 3.5 to 36 kg.mol-1 exhibit molar mass dependent nucleation and growth of crystals, crystal morphologies, and melting properties at a temperature of 22.5 degrees C in Langmuir films at the air/water (A/W) interface. At surface area per monomer, A, greater than approximately 0.37 nm2.monomer-1, surface pressure, Pi, and surface elasticity exhibit molar mass independent behavior that is consistent with a semidilute PCL monolayer. In this regime, the scaling exponent indicates that the A/W interface is a good solvent for the liquid-expanded PCL monolayers. Pi-A isotherms show molar mass dependent behavior in the vicinity of the collapse transition, i.e., the supersaturated monolayer state, corresponding to the onset of the nucleation of crystals. Molar mass dependent morphological features for PCL crystals and their subsequent crystal melting are studied by in situ Brewster angle microscopy during hysteresis experiments. The competition between lower segmental mobility and a greater degree of undercooling with increasing molar mass produces a maximum average growth rate at intermediate molar mass. This behavior is analogous to spherulitic growth in bulk PCL melts. The plateau regions in the expansion isotherms represent the melting process, where the polymer chains continuously return to the monolayer state. The magnitude of Pi for the plateau during expansion decreases with increasing molar mass, indicating that the melting process is strongly molar mass dependent.     

Effect of bicarbonate ions on the crystallization of calcite on self-assembled monolayers

We use molecular dynamics simulations to investigate the nucleation of calcite crystals on self-assembled monolayers. We show how the presence of bicarbonate ions adsorbed on the monolayer surface can both aid nucleation and control the orientation of the growth of the crystal. Using a simple model of the nucleation process and calculated interfacial energies, we calculate the enhancement (with respect to the homogeneous nucleation rate) of the nucleation of calcite on the (012) and (0001) faces. The calculations show clearly that the (012) face is favored over the (0001) face and that the nucleation rate is enhanced for self-assembled monolayers made from molecules containing an even number of carbon atoms in the alkyl chain over those containing an odd number.     

Relaxation behaviors of monolayers of octadecylamine and stearic acid at the air/water interface

This study investigated the relaxation behaviors of octadecylamine (ODA), stearic acid (SA), and SA/ODA mixed monolayers at the air/water interface. Area relaxations of monolayers at constant surface pressure were studied by a nucleation and growth mechanism and by direct observation using a Brewster angle microscope (BAM). The results showed that ODA and SA monolayers exhibit different characteristics in the area loss and in the BAM morphology. In the initial relaxation stage, SA monolayer illustrates a more stable characteristic than ODA. But at the later stage, the area loss of SA monolayer increases more quickly than that for ODA due to significant nucleation and growth of 3D aggregates. The BAM results demonstrated that 3D aggregates of large scale domains are likely to form on a SA monolayer even when the area loss is insignificant. On the contrary, only dotlike aggregates of low density were found on the ODA monolayer when relaxation is carried out at higher surface pressure. The relaxation behavior of SA monolayer can be described by the Vollhardt model. However, the relaxation of ODA monolayer does not follow the nucleation model described by Vollhard but can reasonably be attributed to the effect of dissolution. For the SA/ODA mixed monolayers, the relaxation behaviors in the initial and final stages follow different mechanisms, which is attributed to the formation of distinct phases as observed from the BAM. This result also implied that SA and ODA are not completely miscible to be a homogeneous phase. Phases of various compositions were formed in the mixed monolayers, and thus, the relaxation mechanism was shifted during the relaxation process as dominated by different relaxation behaviors of various phases.     

Electrocrystallization of rhodium clusters on thiolate-covered polycrystalline gold

This study reports on the electrochemical deposition of rhodium metal clusters on a polycrystalline gold electrode, modified with a monolayer of dodecanethiol through self-assembly from solution. The deposition process was investigated using cyclic voltammetry, chronoamperometry, and electrochemical quartz crystal microbalance. It is shown that the presence of the thiol monolayer drastically alters the nucleation and growth mechanism compared with the mechanism on the bare gold electrode. The small uncovered gold domains, located at the imperfections in the thiolate monolayer which are induced by the gold nanoroughness, act as nucleation sites for small rhodium clusters. At longer times, these clusters can outgrow the organic monolayer. The resulting surface morphology was characterized by scanning electron microscopy. Rhodium electrocrystallization on the bare gold substrate resulted in an ensemble of a very large amount of very small clusters that are difficult to distinguish from the gold roughness. In contrast, in the presence of a self-assembled monolayer (SAM) of dodecanethiol covalently attached to the gold electrode, the resulting deposit consisted of an ensemble of hemispherical particles. The size distribution of the rhodium particles obtained by using double step chronoamperometry was compared to the ones obtained with cyclic voltammetry and "classical" chronoamperometry. It is shown by X-ray photoelectron spectroscopy that the SAM is still present after rhodium deposition on the thiolate-covered gold substrate. Because the rhodium clusters are directly attached to the gold substrate and can thus easily be electrified, the resulting interface could be used as a composite electrode consisting of a random array of gold supported rhodium nano/microparticles separated from each other by an organic phase. On the other hand, it is shown that the SAM is easily removed by electrochemical oxidation without dissolving the rhodium clusters and, thus, leaving a different array of rhodium clusters on the gold surface compared with the topography obtained in the absence of the SAM. From this point of view, substrate modification with such "removable" organic monolayers was found to be an interesting tool to tune the nano- or microtopography of electrochemically deposited rhodium.     

Bond insertion, complexation, and penetration pathways of vapor-deposited aluminum atoms with HO- and CH(3)O-terminated organic monolayers

The interaction of vapor-deposited Al atoms with self-assembled monolayers (SAMs) of HS-(CH(2))(16)-X (X = -OH and -OCH(3)) chemisorbed at polycrystalline Au[111] surfaces was studied using time-of-flight secondary-ion mass spectrometry, X-ray photoelectron spectroscopy, and infrared reflectance spectroscopy. Whereas quantum chemical theory calculations show that Al insertion into the C-C, C-H, C-O, and O-H bonds is favorable energetically, it is observed that deposited Al inserts only with the OH SAM to form an -O-Al-H product. This reaction appears to cease prior to complete -OH consumption, and is followed by formation of a few overlayers of a nonmetallic type of phase and finally deposition of a metallic film. In contrast, for the OCH(3) SAM, the deposited Al atoms partition along two parallel paths: nucleation and growth of an overlayer metal film, and penetration through the OCH(3) SAM to the monolayer/Au interface region. By considering a previous observation that a CH(3) terminal group favors penetration as the dominant initial process, and using theory calculations of Al-molecule interaction energies, we suggest that the competition between the penetration and overlayer film nucleation channels is regulated by small differences in the Al-SAM terminal group interaction energies. These results demonstrate the highly subtle effects of surface structure and composition on the nucleation and growth of metal films on organic surfaces and point to a new perspective on organometallic and metal-solvent interactions.     

硼酸对赖氨酸盐酸盐在半胱氨酸自组装膜上晶体生长的影响

研究了利用半胱氨酸自组装膜对诱导L-赖氨酸盐酸盐晶体生长的影响。实验发现,赖氨酸盐酸盐优先在水溶液内而不是在自组装膜表面成核生长为晶体,这是首次发现自组装单层对赖氨酸盐酸盐的成核有抑制作用。对自组装单层上的成核机理进行了探讨,2种氨基酸正电荷间的排斥作用可能是自组装膜抑制赖氨酸盐酸盐成核的原因。在赖氨酸盐酸盐溶液中加入了等摩尔硼酸,XRD结果表明,硼酸晶体优先生长在自组装单层上。而析出后的硼酸晶体又加速促进了赖氨酸盐酸盐的结晶析出。扫描电子显微镜表征发现,加入硼酸后赖氨酸盐酸盐晶体的形貌发生了很大变化,由原来的块状变为针状。实验结果表明,加入硼酸,可以加速赖氨酸盐酸盐的晶体生长并可以调控晶体的形貌和取向。     

Nucleation of Boron-Nitrogen on Transition Metal Surface: A First-Principles Investigation

Boron nitrogen (BN) monolayer has attracted considerable attention because of their successful incorporation with graphene based nanodevices. However, many important aspects of the growth mechanisms are still not well explored. Using density functional theory (DFT) calculations, we found that Cu(111) surface is more suitable to be used as a substrate to grow BN monolayer compared with Ni(111) surface. Moreover, we explored that one-dimensional (1D) BN chain configuration is dominant to the two-dimensional (2D) BN ring formation from one pair to five BN pairs deposited on Cu(111) surface. Energetically stable structure transformation of BN monolayer from 1D BN chain to 2D BN ring occurs when the number of pairs is n>5. It is suggested that, as the number of BN pairs increases the energetically stable structures achieve.     

Template adaptability is key in the oriented crystallization of CaCO3

In CaCO3, biomineralization nucleation and growth of the crystals are related to the presence of carboxylate-rich proteins within a macromolecular matrix, often with organized beta-sheet domains. To understand the interplay between the organic template and the mineral crystal it is important to explicitly address the issue of structural adaptation of the template during mineralization. To this end we have developed a series of self-organizing surfactants (1-4) consisting of a dodecyl chain connected via a bisureido-heptylene unit to an amino acid head group. In Langmuir monolayers the spacing of these molecules in one direction is predetermined by the hydrogen-bonding distances between the bis-urea units. In the other direction, the intermolecular distance is determined by steric interactions introduced by the side groups (-R) of the amino acid moiety. Thus, by the choice of the amino acid we can systematically alter the density of the surfactant molecules in a monolayer and their ability to respond to the presence of calcium ions. The monolayer films are characterized by surface pressure-surface area (pi-A) isotherms, Brewster angle microscopy, in-situ synchrotron X-ray scattering at fixed surface area, and also infrared reflection absorption spectroscopy (IRRAS) of films transferred to solid substrates. The developing crystals are studied with scanning and transmission electron microscopy (SEM, TEM), selected area electron diffraction (SAED), and crystal modeling. The results demonstrate that although all compounds are active in the nucleation of calcium carbonate, habit modification is only observed when the size of the side group allows the molecules to rearrange and adapt their organization in response to the mineral phase.     

Two-dimensional arrays of amphiphilic Zn2+-cyclens for guided molecular recognition at interfaces

The sterically guided molecular recognition of nucleobases, phosphates, adenosine, and uridine nucleotides on Langmuir monolayers and Langmuir-Blodgett monolayers of amphiphilic mono- or bis(Zn2+-cyclen)s assembled on thiolated surfaces was investigated. The stepwise selective binding of metal ions, uracil, or phosphate by dicetyl cyclen monolayers with variously tuned structures at the air/water interface was corroborated by the measurements of the corresponding LB films deposited onto quartz crystals. Two types of recognition surfaces were fabricated from Zn2+-dicetyl cyclen. The surface covered with a complex preformed in the Langmuir monolayer was capable both of imide and of phosphate binding. The similar complex formed directly in an LB film on thiolated gold was inactive with respect to imide. The surface plasmon resonance measurements evidenced the stepwise assembly of complementary nucleotides on SAM/LB templates through consecutive phosphate-Zn2+-cyclen coordination. Base pairing between nucleotides resulted in a formation of A-U bilayers comprising two complementary monolayers. Finally, we report on SAM/LB patterns designed for divalent molecular recognition of uridine phosphate by amphiphilic bis(Zn2+-cyclen).     

Phase behavior and viscoelastic properties of trisilanolcyclohexyl-POSS at the air/water interface

A trisilanol polyhedral oligomeric silsesquioxane (POSS), trisilanolcyclohexyl-POSS (TCyP), has recently been reported to undergo a series of phase transitions from traditional Langmuir monolayers to unique rodlike hydrophobic aggregates in multilayer films that are different from "collapsed" morphologies seen in other systems at the air/water interface. This paper focuses on the phase transitions and morphology of films varying in average thickness from monolayers to trilayers and the corresponding viscoelastic properties of trisilanolcyclohexyl-POSS molecules at the air/water interface by means of surface pressure-area per molecule (Pi-A) isotherms, Brewster angle microscopy (BAM), and interfacial stress rheometry (ISR) measurements. The morphology studies by BAM reveal that the TCyP monolayer can collapse into different 3D structures by homogeneous or heterogeneous nucleation mechanisms. For homogeneous nucleation, analysis by Vollhardt et al.'s nucleation and growth model reveals that TCyP collapse is consistent with instantaneous nucleation with hemispherical edge growth at Pi = 3.7 mN.m(-1). Both surface storage (Gs') and loss (Gs") moduli obtained by ISR reveal three different non-Newtonian flow regimes that correlate with phase transitions in the Pi-A isotherms: (A) A viscous liquidlike "monolayer"; (B) a "biphasic regime"between a liquidlike viscous monolayer and a more rigid trilayer; and (C) an elastic solidlike "trilayer". These observations provide interesting insights into collapse mechanisms and structures in Langmuir films.     

ALD resist formed by vapor-deposited self-assembled monolayers

A new process of applying molecular resists to block HfO2 and Pt atomic layer deposition has been investigated. Monolayer films are formed from octadecyltrichlorosilane (ODTS) or tridecafluoro-1,1,2,2-tetrahydrooctyltrichlorosilane (FOTS) and water vapor on native silicon oxide surfaces and from 1-octadecene on hydrogen-passivated silicon surfaces through a low-pressure chemical vapor deposition process. X-ray photoelectron spectroscopy data indicates that surfaces blocked by these monolayer resists can prevent atomic layer deposition of both HfO2 and Pt successfully. Time-dependent studies show that the ODTS monolayers continue to improve in blocking ability for as long as 48 h of formation time, and infrared spectroscopy measurements confirm an evolution of packing order over these time scales.     

Formation and dissolution processes of the 6-thioguanine (6TG) self-assembled monolayer. A kinetic study

This is a report on the kinetics of the destruction and formation processes of the 6-thioguanine self-assembled monolayer (6TG SAM) on a mercury electrode from acid solutions by chronoamperometry. The destruction of the 6TG SAM that has been previously formed under open circuit potential conditions is carried out by stepping the potential from an initial value where the chemisorbed layer is stable up to potentials where the molecules are no longer chemisorbed. The destruction of the SAM has been described by a model that involves three types of contributions: (i) a Langmuir-type adsorption process, (ii) a 2D nucleation mechanism followed by a growth controlled by surface diffusion, and (iii) a 2D nucleation mechanism followed by a growth at a constant rate. The nonlinear fit of the experimental transients by using this procedure allows the quantitative determination of the individual contributions to the overall process. The kinetics of the formation process is studied under electrochemical conditions. The chronoamperometric experiment allows us to monitor the early stages of 6TG SAM formation. The implications of the physisorbed state at low potentials in the type of monolayer formation and destruction processes as well as the influence of temperature are also discussed.     

Localized Crystallization of Enantiomeric Organic Compounds on Chiral Micro‐patterns from Various Organic Solutions

The controlled crystallization of enantiomers of an organic compound (a cyclic phosphoric acid derivative) on templated micro‐patterned functionalised surfaces is demonstrated. Areas where a complementary chiral thiol has been located were effective heterogeneous nucleation centres when a solution of the compound is evaporated slowly. Various organic solvents were employed, which present a challenge with respect to other examples when water is used. The solvent and the crystallization method have an important influence on the crystal growth of these compounds. When chloroform was employed, well‐defined crystals grow away from the surface, whereas crystals grow in the plane from solutions in isopropanol. In both cases, nucleation is confined to the polar patterned regions of the surface, and for isopropanol growth is largely limited within the pattern, which shows the importance of surface chemistry for nucleation and growth. The apparent dependence on the enantiomer used in the latter case could imply stereo‐differentiation as a result of short‐range interactions (the templating monolayer is disordered, even at the nanometre scale). The size of the pattern of chiral monolayer also determines the outcome of the crystallization; 5 μm dots are most effective. Despite the low surface tension of the samples (relative to the high surface tension of water), differential solvation of the polar and hydrophobic layers of the solvents allows crystallization in the polar regions of the monolayer, therefore the polarity of the regions in which heterogeneous nucleation takes place is indeed very important. Despite the complex nature of the crystallization process, these results are an important step towards to the use of patterned surfaces for heterogeneous selective nucleation of enantiomers.     

Hydrogels coupled with self-assembled monolayers: an in vitro matrix to study calcite biomineralization

This paper describes the control of the nucleation and growth of calcite crystals by a matrix composed of an agarose hydrogel on top of a carboxylate-terminated self-assembled monolayer (SAM). The design of this matrix is based upon examples from biomineralization in which hydrogels are coupled with functionalized, organic surfaces to control, simultaneously, crystal morphology and orientation. In the synthetic system, calcite crystals nucleate from the (012) plane (the same plane that is observed in solution growth). The aspect ratio (length/width) of the crystals decreases from 2.1 +/- 0.22 in solution to 1.2 +/- 0.04 in a 3 w/v % agarose gel. One possible explanation for the change in morphology is the incorporation of gel fibers inside of the crystals during the growth process. Etching of the gel-grown crystals with deionized water reveals an interpenetrating network of gel fibers and crystalline material. This work begins to provide insight into why organisms use hydrogels to control the growth of crystals.     

Molecular orientation of evaporated pentacene films on gold: alignment effect of self-assembled monolayer

Pentacene films deposited on self-assembled monolayers (SAMs) bearing different terminal functional groups have been studied by reflection-absorption IR, grazing angle XRD, NEXAFS, AFM, and SEM analyses. A film with pentacene molecules nearly perpendicularly oriented was observed on Au surfaces covered with an SAM of alkanethiol derivative of X-(CH2)(n)-SH, with X = -CH(3), -COOH, -OH, -CN, -NH(2), C(60), or an aromatic thiol p-terphenylmethanethiol. On the other hand, a film with the pentacene molecular plane nearly parallel to the substrate surface was found on bare Au surface. A similar molecular orientation was found in thinner ( approximately 5 nm) and thicker (100 nm) deposited films. Films deposited on different surfaces exhibit distinct morphologies: with apparently smaller and rod-shaped grains on clean bare Au surface but larger and islandlike crystals on SAM-modified surfaces. X-ray photoemission electron microscopy (X-PEEM) was used to analyze the orientation of pentacene molecules deposited on a SAM-patterned Au surface. With the micro-NEXAFS spectra and PEEM image analysis, the microarea-selective orientation control on Au was characterized. The ability to control the packing orientation in organic molecular crystals is of great interest in fabricating organic field effect transistors because of the anisotropic nature of charge transport in organic semiconducting materials.     

AFM observations of phase transitions in molecularly thin films of a three-ring bent-core compound

Submonolayer thin films of a three-ring bent-core (or banana-shaped) compound, m-bis(4-n-octyloxystyryl)benzene (m-OSB), were vacuum-deposited on a mica surface, and a spontaneous transition from monolayer films to bilayer crystals was observed at room temperature, which was ascribed to the specific molecular shape and polar layered packing of the bent-core molecules [Tang et al. J. Phys. Chem. B 2004, 108 (34), 12921-12926]. The crystal nucleation and growth from the monolayer films as well as the melting phase transition from the bilayer crystals were investigated using atomic force microscopy (AFM). It was shown that after initial nucleation, the crystal growth was achieved through three pathways: direct absorption of molecules from monolayer films, molecular cluster diffusion, and quasi-Ostwald ripening. When annealing the bilayer crystals at elevated temperatures, morphological change from a bilayer to a monolayer was observed, and some new islands with fingerlike patterns were formed during this process, which resulted from a diffusion-controlled growth of the molten molecules. In general, the high-resolution AFM in combination with the molecularly thin m-OSB films provided us with direct visualization of nucleation, crystal growth, melting, and film morphology evolution on the mesoscopic scale, which are of fundamental interest from the theoretical viewpoint and are of central importance for the control of interfacial properties in practical applications.     

Oriented Crystallization on Organic Monolayers to Control Concomitant Polymorphism

Nucleation events and crystal growth can be guided by molecular recognition at interfaces through intermolecular interactions. The short-acting antimicrobial sulfa drug sulfathiazole is known for its concomitant crystallization, which has five known polymorphs, due to conformational flexibility and hydrogen-bond synthon variation. In its development stage of a drug the issue of concomitant crystallization needs to be addressed with respect to patent litigation, including legal actions to protect patents against infringement. A functional self-assembled monolayer (SAM) of organic thiol on a gold surface has been employed as an efficient approach to control concomitant nucleation of such flexible drugs. The crystallization on a SAM surface is mostly kinetically driven and often leads to the nucleation of novel metastable forms. Spectroscopic, thermal analysis and X-ray diffraction studies reveal that a previously unknown, sixth form of the drug nucleates on the designed SAM surface.     

Orthogonally reactive SAMs as a general platform for bifunctional silica surfaces

We report the synthesis and self-assembly of azide and amine trimethoxysilanes that result in mixed monolayers on silica. The amine and azide functional groups can be independently reacted with acid chlorides and terminal alkynes, respectively. Consequently, these orthogonally reactive monolayers represent a general starting point for making bifunctional surfaces. Using X-ray photoelectron spectroscopy, we determined the azide/amine surface ratio as well as the reactivity of the azide and amine functional groups in the mixed self-assembled monolayer (SAM). Significantly, the surface azide/amine ratio was much lower than the azide/amine ratio in the self-assembly mixture. After determining the self-assembly mixture composition that would afford 1:1 azide-amine mixed monolayers, we demonstrated their subsequent functionalization. The resulting bifunctional surface has a similar functional group ratio to the azide/amine precursor SAM demonstrating the generality of this approach.