酸性湖蓝7在LDO上吸附性能及机理的研究

探讨了Mg/Al＝3的水滑石焙烧产物(MgAl-LDO)对染料酸性湖蓝7(AB7)的吸附性能及其机理. 考察了不同因素对MgAl-LDO吸附AB7性能的影响, 并研究了吸附过程的热力学机理. 实验结果表明: MgAl-LDO对AB7具有优异的吸附性能, 在288 K, pH＝6.74条件下, 0.33 g·L^-1 MgAl-LDO对150 mg·L^-1AB7溶液的吸附容量和去除率分别达到446.9 mg·g^-1和99.31%. 热力学研究表明: MgAl-LDO对AB7的吸附过程同时符合Langmuir 和 Freundlich等温吸附方程, 并且是个放热、自发的过程. 计算所得的吉布斯自由能绝对值在8～10 kJ·mol^-1, 这主要是由染料分子与水滑石层板的氢键作用产生, 结合Materials Studio 5.5软件模拟AB7染料分子在MgAl-LDHs上的排列分布, 推测MgAl-LDO对AB7的吸附机理是表面吸附作用. 同时, 经4次回收, LDO对AB7的去除率仍达到85%以上.     

阴离子型有机化合物在LDHs上的动力学和热力学研究

考察了水滑石焙烧产物MgAl-LDO吸附3种阴离子染料Acid Red 88(AR88)、Acid Orange 3(AO3)、Acid Violet 90(AV90)过程中的热力学和动力学机理,并在不同温度下探究该吸附过程的热力学参数。实验结果表明:MgAl-LDO对染料阴离子的吸附过程复合Langmuir吸附等温模型,且为自发、放热的过程。3种染料在MgAl-LDO上的吸附过程均符合准二级反应动力学模型,且该吸附过程是由MgAl-LDO与阴离子染料之间的反应速率控制而不是两者之间的扩散作用。计算所得的吉布斯自由能绝对值在7~15 kJ·mol-1,这主要是由染料阴离子与MgAl-LDHs层板的氢键作用产生,结合Materials Studio 5.5软件模拟染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对阴离子染料的吸附机理是表面吸附(占优势)与层间插层的协同作用。     

阴离子型有机化合物在LDHs上的动力学和热力学研究

本文考察水滑石焙烧产物MgAl-LDO吸附3种阴离子染料AcidRed88（AR88）、AcidOrange 3（AO3）、AcidViolet90（AV90）过程中的热力学和动力学机理,并在不同温度下探究该吸附过程的热力学参数。实验结果表明：MgAl-LDO对染料阴离子的吸附过程复合Langmuir吸附等温模型,且为自发、放热的过程。3种染料在MgAl-LDO上的吸附过程均符合准二级反应动力学模型,且该吸附过程是由MgAl-LDO与阴离子染料之间的反应速率控制而不是两者之间的扩散作用。计算所得的吉布斯自由能绝对值在7~15kJ·mol^-1,这主要是由染料阴离子与MgAl-LDHs层板的氢键作用产生,结合MaterialsStudio 5.5软件模拟染料分子在MgAl-LDHs上的排列分布,推测MgAl-LDO对阴离子染料的吸附机理是表面吸附（占优势）与层间插层的协同作用。     

Mg/Al水滑石的焙烧产物吸附酸性红88的动力学和热力学机理研究

文章研究了Mg/Al水滑石焙烧产物(LDO)对酸性红88 (AR88)的吸附性能及其机理. 考察了温度对其吸附性能的影响, 探讨了吸附过程的动力学和热力学规律. 热力学研究表明: LDO对AR88的吸附过程稍符合Langmuir等温吸附. 从Langmuir等温式计算的 , 为负值, 表明吸附过程为放热、熵减小的过程, 这是因为LDO在吸附酸性染料后恢复了层状结构|不同温度下 均为负值, 表明吸附过程是自发进行的. 动力学研究表明: 吸附动力学符合准二级动力学模型, 动力学计算吸附过程的活化能E_a＝54.53 kJ•mol^－1. 利用Materials Studio 4.3软件中的CASTEP程序模块和Focite模块模拟了AR88染料分子在Mg/Al水滑石(LDHs)的尺寸大小和排列方式, 推测吸附机理是以表面吸附占主要优势并伴有少部分插层.     

Mg/Al-NO_3 LDH吸附诺氟沙星的热力学和动力学研究

采用平衡吸附实验,研究了诺氟沙星在自制焙烧态镁铝水滑石(Mg/Al-NO_3 LDH)上的吸附热力学和动力学行为。结果表明,在固液比1∶500、p H=5.0、吸附温度25℃、离子强度0.1 mol/L的条件下,吸附1 h对诺氟沙星(20 mg/L)的吸附过程符合Langmuir等温线方程和准二级动力学,理论平衡吸附量达到32.05 mg/g。其热力学参数ΔG0 KJ/mol,ΔH0 KJ/mol,由此推断焙烧态镁铝水滑石对诺氟沙星的吸附是自发放热反应。     

镁铝类水滑石对阳离子染料中性红的吸附及机理研究

研究了镁铝类水滑石对中性红的吸附及其作用机理,考察了时间、pH、温度、电解质浓度等因素对吸附作用的影响。结果表明,镁铝类水滑石对中性红的吸附动力学符合准二级动力学方程,热力学符合Langmuir吸附等温式。在实验范围内,吸附量随溶液pH的增大而增加,随温度的升高而降低,随电解质浓度的增加先增加后降低。吸附过程是放热、熵减小的自发过程。镁铝类水滑石对中性红的吸附缘于为类水滑石与中性红分子中π电子的较强静电吸引作用。     

镍铁类水滑石对偶氮阴离子染料的吸附脱色作用

采用镍铁类水滑石作为吸附剂,对偶氮阴离子染料酸性大红G、活性艳红X-3B和直接耐酸大红4BS废水进行脱色处理,研究了时间、镍与铁的物质的量之比、初始pH和无机电解质添加剂等因素对脱色率的影响,并结合红外光谱和X射线衍射分析结果讨论了其吸附脱色机理.结果表明,三种染料在镍铁类水滑石上的吸附均为层间的阴离子交换吸附和外表面的吸附.通过阴离子交换进入层间后,不同于直接耐酸大红4BS阴离子,酸性大红G和活性艳红X-3B两种阴离子与水滑石层间水分子之间产生氢键作用;在化学键合过程中,染料分子被镍铁类水滑石表面Fe3+氧化,同时偶氮键断裂导致脱色.     

谷氨酸插层水滑石吸附水中铅离子

采用共沉淀法合成了谷氨酸插层镁铝类水滑石(LDH),对所制备的试样进行了X-射线衍射和红外光谱表征,对LDH去除水中铅离子的能力进行了讨论,研究了吸附过程的吸附动力学和吸附等温线。结果表明,谷氨酸能嵌入镁铝水滑石的层间,该插层水滑石能有效吸附水中铅离子,吸附过程符合准二级动力学模型,吸附等温曲线可用Langmuir模型来描述,吸附量可达68.49mg/g。     

半互穿海藻酸钠/聚丙烯酰胺凝胶吸附结晶紫动力学/热力学行为和吸/脱附机理

将含有大量—COO-的聚阴离子海藻酸钠(SA)引入聚丙烯酰胺(PAM)凝胶网络中,采用自由基溶液聚合法制备半互穿网络结构的SA/PAM水凝胶.采用扫描电子显微镜(SEM)、X射线光电子能谱(XPS)和傅里叶变换红外光谱(FTIR)分析了SA/PAM水凝胶吸附结晶紫(CV)前后的孔洞形态和化学组成变化,采用多种模型研究了SA/PAM水凝胶对CV分子的吸附动力学和热力学行为,并探讨了脱附效率,提出了吸脱附机理.研究结果表明,SA的引入降低了孔径尺寸,增加了孔洞数量;SA/PAM-10凝胶对CV分子吸附量最大,达到13.5838 mg/g,符合伪一级吸附动力学模型,吸附速率受膜扩散和粒子内扩散过程共同影响;等温吸附过程符合Temkin和D-R模型,属于微孔多层吸附;热力学分析结果表明,吸附过程由熵驱动引起,非化学诱导因素影响所致;采用HCl进行脱附,最大脱附率高达94.18%,加入Na OH可实现SA/PAM水凝胶的可逆吸附;较高的吸附量主要源于SA分子链上的COO-与CV分子的—C N+—存在的静电作用,低pH值时由于—COO-和—NH2质子化导致与CV分子的静电斥力增大,脱附率随之增加.     

羟基硝酸锌对甲基橙的吸附性能研究

本文研究了采用直接沉淀法合成的羟基硝酸锌(ZHN)对甲基橙的吸附性能,分析了ZHN的吸附热力学、动力学行为,并探讨了吸附机理;同时还研究了溶液初始pH值和ZHN使用量对ZHN吸附效果的影响规律。结果表明：高温时ZHN的吸附热力学行为更符合Freundlich模型,低温时更符合Langmuir模型,其吸附动力学过程更符合准二级动力学方程;低温或低平衡浓度条件转变为高温或高平衡浓度条件时,吸附机理从表面吸附为主逐步过渡为以表面吸附和层间离子交换吸附共同作用方式为主;pH=7的中性溶液中ZHN对甲基橙的吸附率最高,ZHN使用量对吸附率和单位平衡吸附量影响规律呈相反趋势。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.