Reaction of poly(vinyl chloride) with superoxide anion

Reaction of poly(vinyl chloride) (PVC) with superoxide anion was carried out in tetrahydrofuran (THF) at 40°C in a nitrogen atmosphere. Remarkable changes in infrared (IR) spectra of the samples treated with superoxide anion were observed in the following regions: ca. 3300, 1680, 1620, and 765 cm^?1, which suggested the formation of hydroxyl groups, α,β-unsaturated ketone groups, and ethylenic structures. Ultraviolet–visible spectra also showed the formation of polyene structures. The content of chlorine in the polymer decreased and that of oxygen increased with reaction time. The reaction mechanism was discussed on the basis of these results.     

Novel amine-containing biodegradable polyester via copolymerization of aspartic anhydride and 1,4-cyclohexanedimethanol

A novel biodegradable polyester having pendant amine functional groups was snythesized from N-(benzyloxycarbonyl)-L -aspartic anhydride ( 2 ) and 1,4-cyclohexanedimethanol ( 3 ) by polycondensation reaction using p-toluenesulfonic acid as a catalyst. The synthesized polymer 4 shows the characteristic ester carbonyl absorption peak at 1732 cm⁻¹ in the IR spectrum, and the NMR spectra were consistent with the IR data. Also, the elemental analysis showed that the experimental and calculated values were very close to each other. The weight-average molecular weight of the polymers ranged from 1140 to 5050 and increased with increasing reaction time. This new polymer would have the potential of a drug delivery biomaterial.     

Polyethynylferrocene

The completely conjugated polymer, polyethynylferrocene, was prepared by heating ethynylferrocene with catalytic amounts of azobisisobutyronitrile to 180-240[ddot] under nitrogen in bulk. Cyclotrimerization competes with polymerization under these conditions. Pure low molecular weight polyethynylferrocene was isolated and characterized by IR and NMR spectroscopy and by a gel permeation chromatography. The pure polymer exhibits a conductivity of 2 × 10^{?14 ?1} cm^?1. Attempts to prepare polyethynylferrocene by heating acetylferrocene in molten zinc chloride were, contrary to literature reports, unsuccessful. A polymer containing hydroxyl and keto groups was obtained, and extensive degradation of the ferrocene groups occurred. The general reaction scheme is discussed. It includes cleavage of cyclopentadienyl rings from ferrocene and the incorporation of cyclopentane rings into the polymer structure.     

Sulfophthalide cycle cleavage and formation of fluorenyl structures upon poly(diphenylene sulfophthalide) thermolysis

Thermolysis of poly(diphenylene sulfophthalide) (PDSP) in the temperature range from 100 to 500 °C was studied by IR and UV-Vis spectroscopy and thermogravimetric analysis. A series of absorption bands in the IR spectrum of PDSP were assigned on the basis of the theoretical calculations of the IR spectrum of diphenyl sulfophthalide used as a model compound, in particular, ν_as(S=O) = 1352 cm^?1, ν_s(S=O) = 1196 cm^?1, ν(C-O) ～ 920 cm^?1, ν(S-O) = 824 cm^?1, and δ(SO₂) = 576 cm^?1. The sulfophthalide cycle (SPC) in PDSP decomposes at the thermolysis temperatures in a range of 260–400 °C. An analysis of the IR spectra of the thermolyzate and the quantum chemical calculations of the IR spectra of the model compounds confirmed the predominant formation of fluorenyl structures in the thermolyzed polymer. The changes in the UV-Vis spectra observed upon the thermolysis of thin films of PDSP (the hypsochromic shift of the long-wavelength absorption band from 271 to 263 nm and the appearance a shoulder at ～310 nm) and the results of TD-DFT calculations of the UV-Vis spectra of the model compounds are consistent with the hypothesis about the formation of fluorenyl structures. The general scheme of PDSP thermolysis at 260–400 °C was proposed in which the major process is the formation of fluorenyl fragments in macromolecules of the polymer due to the intramolecular ring closure in biradicals formed by the SPC cleavage.     

First Example of Schiff Bases Containing Poly(Acryl Amid) in the Synthesis and Characterization

A novel polymeric‐Schiff base derived from the condensation reaction poly(acryl amid) and indole‐3‐carboxaldehyde has been synthesized and their Co(II) and Ni(II) complexes have been prepared. Mol ratio of acrylamid group and Schiff bases group was estimated by means of height of ‐CH multiple peaks and –CH=N‐ peak in ¹H‐NMR spectrum. The studied substances were characterized by molar conductance, magnetic susceptibility, electronic and IR spectral studies. In addition, main units have been suggested with elemental analysis for these substances, and than the weight average molecular weight (M_w) has been suggested. The number average molecular weight (M_n) was determined with a vapor pressure osmometer. Polydispersity index (PDI) found to be ca 1.7 from M_w/M_n for poly‐Schiff bases and their Co(II) and Ni(II) complexes. PAA‐Schiff bases were found to have the highest thermal stablility compared to that of the Co(II) and Ni(II) complexes. The conductivities of the PAA‐Schiff bases and their complexes were measured by the four‐probe technique and were found in the range 10^?5?10^?6 S cm^?1.     

Discriminating Amino Resin Paints From Alkyd Resin Paints with Two Kinds of Pigments in Automotive Coatings in Forensic Analysis by FTIR Spectroscopy

The analysis of automotive coatings is important to forensic scientists, especially in the investigation of hit-and-run accidents. Amino resin paints, alkyd resin paints, and polyurethane paints are all popular automotive coatings. In this study, FTIR was employed to investigate these coatings, particular in amino resin paints. IR spectra were tentatively interpreted. The indicative peaks distinguishing amino resin paints (1550 cm^?1) and alkyd resin paints (1600 cm^?1/1580 cm^?1) were summarized. Two kinds of alkyd resin paints (with the Pigment Scarlet Powder and with the Toluidine Red), which were frequently confronted in cases and might readily be read as amino resin paints in IR spectra, were studied and interpreted. The indicative peaks (1619 cm^?1, 776 cm^?1 and 1674 cm^?1, 1494 cm^?1) were selected to discriminate these two kinds of alkyd resin paints from amino resin paints and avoid an incorrect certificate of authenticity. The data in this study can help the forensic scientists identify these three paints accurately, especially in the cases with the interference of the pigments.     

Some 1-substituted quaternary imidazolium compounds and related polymers: Qualitative and quantitative infrared analysis

It was found that 1-substituted quaternary imidazolium compounds show some characteristic infrared (IR) activity. On quarternization of 1-substituted imidazoles strong absorption bands appeared at about 1150 and 1550 cm^?1 in the IR spectra of these compounds. The band at 1150 cm^?1 was assigned to the position 2 C?H bending mode and the 1550 cm^?1 band was attributed to a ring vibration mode of the quaternary imidazolium compounds. The concentration of the quaternary imidazolium units in a polymer can be determined by measuring the intensity of the absorption bands at 1150 or 1550 cm^?1 in relation to another suitable absorption band of the spectrum.     

A novel synthesis of polyethers with pendant hydroxyl groups by polyaddition of bis(oxetane)s with bis(phenol)s

The polyaddition of 1,4-bis[(3-ethyl-3-oxetanyl)methoxymethyl]benzene (BEOB) with 3,3′,5,5′-tetrachlorobisphenol A (TCBPA) was examined with or without catalysts. High molecular weight polymer (polymers 1) (M_n = 13,600) with pendant primary hydroxyl groups was obtained in a 99% yield without any gel products when the reaction was performed with 5 mol % of tetraphenylphosphonium bromide as a catalyst in NMP at 160°C for 96 h. However, when the reaction was carried out without a catalyst under the same conditions, a low molecular weight polymer (M_n = 3200) was obtained in a 51% yield. The structure of the resulting polymer was confirmed by IR, ¹H-NMR, and ¹³C-NMR spectra. In this reaction system, it was also found that tetraphenylphosphonium iodide and crown ether complexes such as 18-crown-6 (18-C-6)/KBr and 18-C-6/KI have high catalytic activity. Polyadditions of 1,4-bis[(3-methyl-3-oxetanyl)methoxymethyl]benzene with TCBPA and BEOB with 3,3′,5,5′-tetrabromobisphenol-S were also examined, and corresponding polymers (polymers 2 and 3) were obtained in good yields. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2781–2790, 1999     

Synthesis and characterization of poly(ethylene oxide‐co‐ethylene carbonate) macromonomers and their use in the preparation of crosslinked polymer electrolytes

Methacrylate‐functionalized poly(ethylene oxide‐co‐ethylene carbonate) macromonomers were prepared in two steps by the anionic ring‐opening polymerization of ethylene carbonate at 180 °C, with potassium methoxide as the initiator, followed by the reaction of the terminal hydroxyl groups of the polymers with methacryloyl chloride. The molecular weight of the polymer went through a maximum after approximately 45 min of polymerization, and the content of ethylene carbonate units in the polymer decreased with the reaction time. A polymer having a number‐average molecular weight of 2650 g mol^?1 and an ethylene carbonate content of 28 mol % was selected and used to prepare a macromonomer, which was subsequently polymerized by UV irradiation in the presence of different concentrations of lithium bis(trifluoromethanesulfonyl)imide salt. The resulting self‐supportive crosslinked polymer electrolyte membranes reached ionic conductivities of 6.3 × 10^?6 S cm^?1 at 20 °C. The coordination of the lithium ions by both the ether and carbonate oxygens in the polymer structure was indicated by Fourier transform infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2195–2205, 2006     

Synthesis and characterization of novel bisphthalonitrile resins linked by different molecular weight main-chain polybenzoxazines

A series of novel type bisphthalonitriles with different molecular weight main-chain polybenzoxazines as linkages have been successfully synthesized using 4, 4′-diaminodiphenyl methane, paraformaldehyde, bisphenol A and 4-nitrophthalonitrile as initial materials. The structures were characterized by Fourier transform infrared (FT-IR) and proton nuclear magnetic resonance (¹H-NMR). The formation of benzoxazine and the existence of nitrile groups were confirmed by the absorbance at 950cm^?1 of benzene attached with oxazine ring and 2231 cm^?1 of nitrile groups. The characteristic resonance peaks observed at about 4.52 (C-CH₂-N) and 5.28 ppm (N-CH₂-O) also determined the structure of benzoxazine ring. The curing behaviors were monitored by differential scanning calorimetry (DSC) and FT-IR. Two-stage polymerization mechanisms were observed according to the ring-opening of benzoxazine and the polymerization of nitrile groups catalyzed by phenolic hydroxyl groups, which generated during the curing reaction of benzoxazine. The polymerization of these bisphthalonitriles exhibited self-promoted curing behaviors. The completion of polymerization was proved by the disappearance of the band located at 950 cm^?1 in FT-IR. Thermogravimetric analysis (TGA) was used to investigate the thermal stability, and the results showed that the cured polymers achieved extremely high char yield from 61.1% up to 74.2% at 800°C under nitrogen and exhibited increasing decomposition temperature as the contents of phthalonitrile groups increased, which indicated that the polymerization of phthalonitriles could improve the thermal stability.     

Novel anionic polyaddition of 2‐trifluoromethylacrylate by double Michael reaction with ethyl cyanoacetate

Novel fluorinated polymer synthesis with anionic polyaddition by double Michael addition reaction of 2‐trifluoromethylacrylate derivatives with ethyl cyanoacetate (ECA) was proposed. Diaddition product of ECA with phenyl 2‐trifluoromethylacrylate was yielded in high yield by the catalysis of sodium ethoxide in tetrahydrofuran at 60 °C. Sodium hydroxide catalyzed double Michael addition reaction also produced diaddition product in high yield. Novel anionic polyaddition of 1,4‐phenylene bis(2‐trifluoromethylacrylate) [CH₂?C(CF₃)COOC₆H₄OCOC(CF₃)?CH₂] (PBFA) with ECA afforded the polymer of 1.2 × 10⁴ as the highest molecular weight. The isolated polymer gave the polymer of 2.8 × 10⁴ as a molecular weight by the reaction of the isolated polymer with PBFA in the presence of sodium ethoxide; which proved that the polymer end groups were mainly ECA moieties. The reaction mechanism that the proton abstraction from ECA followed by the addition of 2trifluoromethylacrylate was proposed. The reaction of acetylacetone with PBFA was also examined to give the polymer of 7.6 × 10³ as the highest molecular weight catalyzed by sodium hydroxide at room temperature. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5698–5708, 2009     

Analysis of polymer films by diffuse reflectance FTIR spectroscopy: Characterization of terminal carboxyl functionalities

Fourier transform infrared (FTIR) spectroscopy in the diffuse reflectance mode was used to study polyethylene terephthalate (PET) films. The polymer film (12 μm, molecular weight M₁ = 18,000) was placed on a finely powdered KBr matrix, used as a reference. Infrared spectra exhibited a new band at 1684 cm^?1, not usually reported in the literature. This band is assigned to the C? O stretching vibration of a terminal acidic function in the presence of internal hydrogen bonds. In the carbonyl region, artifacts created by specular reflection are also discussed. The assignment of the band at 1684 cm^?1 is confirmed by transmission measurements on the overtone of carbonyl group (3335 cm^?1), using polymer films with thicknesses greater than 200 μm and by comparison with polymer of different molecular weight. These acidic functions can be used to monitor the rate of polymerization. It is therefore possible to obtain information on the polymerization rate of PET films, using diffuse reflectance and transmission analysis, directly on the solid. © 1992 John Wiley & Sons, Inc.     

Differentiation of Rhizoma Curcumas Longae and Radix Curcumae by a Multistep Infrared Macro-Fingerprint Method

A multistep infrared macro-fingerprint method was applied to identify two Chinese herbal drugs, Rhizoma Curcumas Longae (RCL) and Radix Curcumae (RC). Fourier transform infrared (FT-IR) spectra of the two were similar to each other and consistent with the 11 peaks of the spectrum of starch. RCL had a characteristic absorption peak at approximately 1514 cm^?1 that correlated to the strong peak near 1509 cm^?1 of curcumin. Between 900 cm^?1–1700 cm^?1 of the second derivative infrared (SD-IR) spectra, with higher resolution, RCL, and curcumin had 10 common peaks. In the FT-IR and SD-IR spectra of the ethanol extract, the spectra of the RCL extract and curcumin were similar, but RC was different. According to the fingerprint characteristics of the infrared spectra for RC and its extracts, the strongest peak at 1055 cm^?1; the C-O absorption peaks at 1124 cm^?1, 1106 cm^?1, and 996 cm^?1; and the strong methylene peaks at 2925 cm^?1 and 2853 cm^?1 suggest that RC contains more saccharides. In the range of 1350 cm^?1–1700 cm^?1, RCL and RC had similar two-dimensional infrared (2D-IR) correlation spectra. Both of them had three autopeaks, but the autopeaks were located at 1458 cm^?1, 1560 cm^?1, and 1641 cm^?1 for RCL and 1458 cm^?1, 1560 cm^?1, and 1669 cm^?1 for RC, suggested that the aromatic components of the two were not identical. The average correlation for the 18 RCL and 18 RC samples were 0.9906 and 0.9878, respectively, and this method achieves a good classification of the sample type.     

Reduction in the moisture absorption of cured MY720/DDS epoxy resins

Thin films of cured MY720/DDS epoxy resins were treated with blocking reagents for hydroxyl, amine, and epoxide functional groups. Infrared spectroscopy (IR) and differential scanning calorimetry (DSC) were used to monitor the progress of the reaction. Treated films were soaked in distilled water at 30°C for 720 h, and the corresponding moisture absorption determined gravimetrically. Samples treated with N-methyl-N-t-butyldimethylsilyl trifluroacetamide (MTBSTFA) containing 1% t-butyldimethylchlorosilane (TBDMCS) in dimethylsulfoxide (DMSO) at 30°C showed a maximum reduction in the IR peak at 3400 cm^?1 (OH and NH) of 39% and a 100% reduction in the epoxide peak at 904 cm, ^?1. The moisture absorption was 1.9%, a reduction of 58% compared to the untreated films (ca. 4.5%). The reactions show dependencies on time and temperature and are diffusion controlled. Samples treated with trimethylsilyl isocyanate (TMSI) in DMSO a 70°C showed 72% reduction in the 3400 cm^?1 IR peak; DSC thermograms do not show an exothermic energy, suggesting that all epoxide groups reacted. These reactions are primarily dependent on time and temperature. The moisture absorption of TMSI treated samples was 1.0% (75% reduction). Samples were also treated with m-trifluoromethyl phenyliscyanate (MTFPI). The reduction in the IR peak at 3400 cm^?1 was 9%, but the moisture absorption was 2.4%—a reduction of 47%.     

Rapid Dynamic Determination of Cetirizine Dihydrochloride in Urine Using Surface Enhanced Raman Scattering with Silver Colloids

A novel method for the dynamic determination of cetirizine dihydrochloride in urine using surface enhanced Raman scattering (SERS) has been developed. Comparison of SERS activities between gold and silver colloid was made based on the analysis of the transmission electron micrographs and the SERS spectra, revealing that silver colloid is much more efficient on the signal enhancement performance. The primary sites of the adsorption on the nanoparticle surface were represented by the feature peaks of piperazine at ca. 1050?cm^?1 and phenyl rings at ca. 1630?cm^?1, respectively. The best signal response was extracted at pH 7 at the Cl^?:Ag⁺ molar ratio of 2:1. The matrix effect was eliminated by subtracting the spectral contribution of the blank urine from the sample spectra. Sample preparation procedures were minimized. Quantification could be simply accomplished on the predicted versus actual concentration curve, within the Raman shift range from 500 to 2500?cm^?1. Neither modeling nor complicate calculation was required. The method was shown to be specific and applicable for drug urine concentration monitoring in situ.     

The Formation of Terminal Double Bonds in Vinyl Chloride Polymerization

The determination of double bonds in PVC is achieved with an increased accuracy in comparison with earlier methods by the addition of iodine monochloride (Wijs reaction) to PVC coupled with x-ray fluorescence analysis to determine the iodine content of the polymer. The number of double bonds per unit weight of polymer increases on increasing the polymerization temperature and is proportional to the number of polymer molecules. It is not affected, however, by the presence of the chain transfer agent tetrahydrofuran (THF). At the technically important polymerization temperatures of 30 to 80°C and in the absence of the chain transfer agent, 0.9 double bonds per polymer molecule are found. The number of double bonds per polymer molecule is lowered using the chain transfer agent THF. These results support the theory that the chain transfer to monomer and possibly the termination reaction are coupled with the formation of terminal double bonds. Contributions by internal double bonds formed by dehydrochlorination of the polymer during polymerization are excluded by investigating the Cl^θ content of the water phase in the oxygen-free VC suspension polymerization. No hydrogen chloride is formed. In IR spectra of PVC, the stretching vibration of the double bonds is detected at 1667 cm^?1 by the correlation of the double bond contents and the intensities of the absorption bands. The stretching vibration at 1667 cm^?1is in accordance with those of model compounds with a 1-chloro-2-alkene structure.     

Importance of the singlet–triplet transition of ethylene in its photopolymerization in the presence of oxygen

The rate of the photopolymerization of ethylene initiated by a mercury are lamp was investigated under a pressure of 400 kg/cm² at 30 ± 5°C by varying the wavelength of incident light. Ethylene was found to polymerize by ultraviolet light below about 3500 Å. The yield decreased gradually as the wavelength became longer, and no polymer was obtained at wavelength greater than 3900 Å. The addition of a small amounr (<100 ppm) of oxygen promoted the polymerization. Ultraviolet absorption spectat measured for the mixture of ethylene and a small amount of oxygen displayed several absorption peaks in the region 2700–3500 Å. The absorption began at about 3680 Å and became stronger with the concentration of oxygen. The average separation between the peaks was about 1000 cm^?1. The spectra were also measured for oxygen containing a small amount of ethylene. Similar absorption peaks with those described above were observed. On the basis of these results, it was pointed out that an excited triplet ethylene is formed under the irradiation of light due to a perturbing effect of oxygen contained in ethylene monomer and the reaction between the excited ethylene and oxygen is important in initiating the polymerization.     

Synthesis of polyurea nanocomposite from industrial waste lignin: Classical curing of isocyanate by lignin-polyamine

Polyurea is an important class of polymer obtained through curing of the isocyanate and polyamine. Here lignin amine processed successive three-step reactions for the synthesis of nanostructure polyurea composite. Further the competence nature is found out by combining different lignin-polyamine with various di-isocyanate. In the first step, lignin was reacted with tosyl-chloride which modified the hydroxy function of lignin as a good leaving group. This reaction for tosylated lignin (Lignin-OTs) has 80% yield. Further lignin-OTs was reacted with four different polyamines replaced tosyl functional group by amine gives aminated lignin. Eventually, a classical reaction of aminated lignin and three different di-isocyanate yield a polyurea composite. A series of changes from lignin to its tosylation eventually to polyurea composite was pursued by the change in the functional group of lignin. The tosylated lignin was confirmed by IR absorption of the C-O peak at 1190 and 1365 cm^?1 and invisible peak absorption at 3500 cm^?1. The aminated lignin was confirmed by IR absorption at 3120 and 3430 cm^?1 for –NH. Thermal gravimetric analysis (TGA) and differential scanning colorimetry (DSC) were used to determine the product's thermal characteristics. Complete structural morphology of nanostructure lignin-polyurea composite was investigated by X-ray diffraction, FE-SEM and EDX.     

Glucose‐induced and fructose‐induced deboronation reaction of 4‐mercaptophenylboronic acid assembled on silver investigated by surface‐enhanced Raman scattering

We examined the deboronation reaction of 4‐mercaptophenylboronic acid (4MPBA) via fructose and glucose on silver surfaces by means of surface‐enhanced Raman scattering (SERS) at the excitation wavelengths of 488, 514, and 633 nm. The SERS spectra on silver nanoparticles clearly exhibited specific spectral signatures of thiophenol (TP) peaks, indicating a deboronation reaction of 4MPBA on the surfaces, whereas no strong TP peaks were observed on gold nanoparticles. The vibrational bands at 417, 999, 1021, and 1574 cm^?1 in the Ag SERS spectra could correspond to the in‐plane aromatic ring modes in TP. X‐ray photoelectron spectroscopy also supported the surface reaction on Ag by referring the B1s peaks at ~193 eV. The ratiometric Raman measurements of the band at 1574 cm^?1, with respect to that at 1587 cm^?1, revealed fructose and glucose quantification in the concentration range of 1–10 mm . We did not identify such changes for mannose, sucrose, and sialic acid. The SERS peaks of 4MPBA on roughened Ag plates also exhibited TP bands to show the time‐dependent spectral change. Our findings indicate that the deboronation of 4MPBA and conjugation with fructose and glucose may be facilitated efficiently on silver surfaces for their quantification. Copyright © 2016 John Wiley & Sons, Ltd.     

Ring‐opening metathesis polymerization of cyclododecene using an electrochemically reduced tungsten‐based catalyst

The ring‐opening metathesis polymerization of cyclododecene using an electrochemically reduced tungsten‐based catalyst (WCl₆? e^?? Al? CH₂Cl₂) is described. In addition, the influence of reaction conditions on the polymerization yield was determined. The resulting polymer has been characterized by NMR, IR, gel permeation chromatography and differential scanning calorimetry. The glass transition temperature and melting point of the polydodecenamer are 19.6°C and 70.0°C respectively. Furthermore, cyclododecene has been polymerized into a low‐molecular‐weight polymer (12.0 × 10³) with a polydispersity of 2.06 in high yields (94%). IR and NMR analysis indicate that the polydodecenamer has a high trans content (60%). Copyright © 2004 John Wiley & Sons, Ltd.