Preparation and properties of alkylated poly(styrene-graft-ethylene oxide)

Poly(styrene-graft-ethylene oxide), having alkyl chains (C₁₂ or C₁₈) on the polystyrene main chain or on the poly(ethylene oxide) (PEO) side chains, were synthesized. The main chain was alkylated by first ionizing amide groups in a styrene/acrylamide copolymer with tert-butoxide, and then using the amide anions as sites for reactions with 1-bromoalkanes. An excess of amide anions was used in the reaction, and the remaining anions were subsequently utilized as initiator sites for the anionic polymerization of ethylene oxide (EO). Synthesis of poly(styrene-graft-ethylene oxide) with alkylated side chains was accomplished by polymerization of EO onto the ionized styrene/acrylamide copolymer, followed by an alkylation of the terminal alkoxide anions with 1-bromoalkanes. The alkylated graft copolymers were structurally characterized by using elemental analysis, ¹H NMR, GPC, and IR spectroscopy. DSC analysis showed that only graft copolymers with PEO contents exceeding about 50 wt % and side chain crystallinities comparable to those of homo-PEO. Main chain alkylated graft copolymers generally had higher crystalinities, as compared to nonalkylated and side chain alkylated samples. The graft copolymers absorbed water corresponding to one water molecule per EO unit at low PEO contents. The water absorption increased progressively at PEO contents above 30 wt % for main chain alkylated samples and above 50 wt % for non-alkylated samples. © 1995 John Wiley & Sons, Inc.     

Free‐radical polymerization of dioxolane and dioxane derivatives: Effect of fluorine substituents on the ring opening polymerization

Partially fluorinated and perfluorinated dioxolane and dioxane derivatives have been prepared to investigate the effect of fluorine substituents on their free‐radical polymerization products. The partially fluorinated monomer 2‐difluoromethylene‐1,3‐dioxolane (I) was readily polymerized with free‐radical initiators azobisisobutyronitrile or tri(n‐butyl)borane–air and yielded a vinyl addition product. However, the hydrocarbon analogue, 2‐methylene‐1,3‐dioxolane (II), produced as much as 50% ring opening product at 60 °C by free‐radical polymerization. 2‐Difluoromethylene‐4‐methyl‐1,3‐dioxolane (III) was synthesized and its free‐radical polymerization yielded ring opening products: 28% at 60 °C, decreasing to 7 and 4% at 0 °C and −78 °C, respectively. All the fluorine‐substituted, perfluoro‐2‐methylene‐4‐methyl‐1,3‐dioxolane (IV) produced only a vinyl addition product with perfluorobenzoylperoxide as an initiator. The six‐membered ring monomer, 2‐methylene‐1,3‐dioxane (V), caused more than 50% ring opening during free‐radical polymerization. However, the partially fluorinated analogue, 2‐difluoromethylene‐1,3‐dioxane (VI), produced only 22% ring opening product with free‐radical polymerization and the perfluorinated compound, perfluoro‐2‐methylene‐1,3‐dioxane (VII), yielded only the vinyl addition polymer. The ring opening reaction and the vinyl addition steps during the free‐radical polymerization of these monomers are competitive reactions. We discuss the reaction mechanism of the ring opening and vinyl addition polymerizations of these partially fluorinated and perfluorinated dioxolane and dioxane derivatives. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5180–5188, 2004     

Polymerization of 1,P-Epoxides Initiated by Tetraalkyl Aluminates. I. Polymerization of Ethylene Oxide in the Presence of Sodium Tetrabutyl Aluminate

The polymerization of ethylene oxide (EO) initiated by NaA1Bu₄ is shown to proceed upon initial complex formation between monomer and initiator. In polymerization in toluene a high order of the kinetic equation with respect to initiator was found, indicating that chain propagation proceeds on dimers and trimers of the active center. An induction time of polymerization in THF is observed. It is necessary to reach a specific concentration of the NaAIBu₄.EO complexes which take part in the polymerization process. The wide molecular weight distribution, the high effectivity coefficient (initiation efficiency), and the polymerization rate increase with polymer yield are evidence of a polycentric polymerization mechanism.     

Ab initio quantum-mechanical calculations of the propagation enthalpies for the radical and anionic polymerizations of formaldehyde and methanimine

The gas phase enthalpies of formation for oligomeric radicals and anions H(CH₂NH)_n^* and H(CH₂O)_n^* were theoretically determined by ab initio quantum-mechanical calculations with n in the range 1 to 6. From these results, the reaction enthalpies for each of the first five propagation steps of the polymerization were estimated for methanimine (H₂C = NH) and formaldehyde (H₂C = O). At the same step of oligomerization, enthalpies associated with anionic polymerizations are always more negative than enthalpies corresponding to radical polymerizations, but the difference between them decreases with increasing n. Both Delta;H (propagation) vs. n curves tend rapidly, particularly for radical polymerizations, towards an asymptotic value independent of the mode of polymerization and equal to - 12 kcal/mol for formaldehyde and - 14 kcal/mol for methanimine. Experimental data for the gas phase polymerization of formaldehyde are in good agreement with our theoretical value. These results demonstrate that heats of polymerization can be reasonably estimated by intensive calculation methods if a careful choice of the reaction mimicking the propagation step is done.     

Polymerization mechanism of trimethylene carbonate carried out with zinc(II) acetylacetonate monohydrate

The proposed mechanism of initiation and course of ring‐opening polymerization of cyclic trimethylene carbonate (TMC) involving zinc(II) acetylacetonate is in accordance with the mechanism of monomer activation. At the first stage of the process, coordination of carbonate to Zn(Acac)₂ · H₂O complex occurs with the release of weakly coordinated water molecules. This free water molecule reacts with active TMC–Zn(Acac)₂ complex. The reaction results in the formation of propanediol and CO₂ emission. During further stages of the investigated process, the formed propanediols, or later the oligomeric diols produced with polymerization, are cocatalysts of the chain propagation reaction. The chain propagation occurs because of repeating activation of the TMC monomer through the creation of an active structure resulting in the exchange/transfer reaction between the zinc complex and the monomer, with its following attachment to the hydroxyl groups, carbonate ring opening, and formation of the carbonic unit of polymer chain. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Large electro‐optic activity and enhanced temporal stability of methacrylate‐based crosslinking hyperbranched nonlinear optical polymer

A methacrylate‐based crosslinking hyperbranced polymers have been synthesized through initiator‐fragment incorporation radical polymerization and used for the temperature stable electro‐optic (EO) polymer application. This polymer consists of methyl methacrylate, 2‐metacryloxyethyl isocyanate, and ethylene glycol dimethacrylate (EGDMA) monomers. The use of EGDMA as a bifunctional unit resulted in the solvent‐soluble crosslinking hyperbranched chain, so that the EO polymer enhanced glass transition temperatures. A phenyl vinylene thiophene vinylene bridge nonlinear optical chromophore was attached to the polymer backbone as the side‐chain by a post‐functionalization reaction. The loading concentration of the chromophore was varied between 30 and 50 wt % by simply changing the mixing ratio of the precursor polymer to the chromophore. The synthesized EO polymers produced optical quality films with a light propagation loss of 0.61 dB/cm in a slab waveguide at 1.31 μm. The electrically poled film had an EO coefficient (r₃₃) of 139 pm/V at 1.31 μm. The EO crosslinking hyperbranced polymer had a high‐glass transition temperature of 170 °C, and exhibited excellent temporal stability of the EO activity at 85 °C for 500 h. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of the amphiphilic macro‐rings of poly(ethylene oxide) with multi‐polystyrene lateral chains and their extraction for dyes

A novel method for synthesis of amphiphilic macrocyclic graft copolymers with multi‐polystyrene lateral chains is suggested, by combination of anionic ring‐open polymerization (AROP) with atom transfer radical polymerization (ATRP). The anionic ring‐opening copolymerization of ethylene oxide (EO) and ethoxyethyl glycidyl ether (EEGE) was carried out first using triethylene glycol and diphenylmethylpotassium (DPMK) as coinitiators; the monomer reactivity ratio of them are r_1(EO) = 1.20 ± 0.01 and r_2(EEGE) = 0.76 ± 0.02 respectively. The obtained linear well‐defined α,ω‐dihydroxyl poly(ethylene oxide) with pendant protected hydroxylmethyls (l‐poly(EO‐co‐EEGE)) was cyclized by reaction with tosyl chloride (TsCl) in the presence of solid KOH. The crude cyclized product containing the extended linear chain polymer was hydrolyzed and then purified by treat with α‐CD. The pure cyclic copolymer with multipendant hydroxymethyls [c‐poly(EO‐co‐Gly)] was esterified by reaction with 2‐bromoisobutyryl bromide, and then used as macroinitiators to initiate polymerization of styrene (St), and a series of amphiphilic macrocyclic grafted copolymers composed of a hydrophilic PEO as ring and hydrophobic polystyrene as side chains (c‐PEO‐g‐PS) were obtained. The intermediates and final products were characterized by GPC, NMR and MALDI‐TOF in detail. The experimental results confirmed that c‐PEO‐g‐PS shows stronger conjugation ability with the dyes than the corresponding comb‐PEO‐g‐PS. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5824–5837, 2007     

Theoretical study of mechanism of cycloaddition reaction between 2,2-dimethyl(2-germavinylidene) [(CH3)2Ge=C:] and formaldehyde

The mechanism of the cycloaddition reaction between singlet 2,2-dimethyl(2-germavinylidene) [(CH₃)₂Ge=C:] and formaldehyde has been investigated with CCSD(T)//MP2/6-311G** method. From the potential energy profile, it could be predicted that the reaction has two competitive dominant reaction pathways. The first pathway consist of the transfer of formaldehyde oxygen π-electrons to the 2p unoccupied orbital of the C: atom in 2,2-dimethyl(2-germavinylidene) with a formation of intermediate which then isomerizes to a four-membered heterocyclic ring carbene (Ge and O in the 1,3-position). The second pathway is a direct [2 + 2] cycloaddition reaction in which the interaction of two π-bonds in 2,2-dimethyl(2-germavinylidene) and formaldehyde generates another four-membered heterocyclic ring carbene (Ge and O in 1,2-position). Because of the unsaturated property of the C: atom in the two four-membered heterocyclic ring carbenes, the two four-membered heterocyclic ring carbenes could further react with formaldehyde, generating two spiro-heterocyclic ring compounds.     

Étude mécanistique et structurale des résines R/F

The follow-up of the advance of the reaction of polymerization of resorcinol with formaldehyde in acid or basic medium by NMR shows that the structure of the obtained xerogel in both cases is the same one. Indeed, the junction between the aromatic nuclei is of type OCH₂OCH₂. While basing itself on the structure of the xerogel, we propose the mechanism for the polymerization reaction between resorcinol and formaldehyde.     

Studies on the intramolecular oxa-Pictet-Spengler rearrangement of 5-aryl-1,3-dioxolanes to 4-hydroxy-isochromans

The success and stereochemical outcome of the TiCl₄-promoted oxa-Pictet-Spengler cyclization of 5-aryl-1,3-dioxolanes to produce 1,3-disubstituted-4-hydroxy-isochromans, is influenced by the length and nature of the side chains bound to C-2 and C-4 of the dioxolane. Methyl groups yield a mixture of 4-hydroxy-isochromans in which the 1,3-trans diastereomer predominates, while bulkier substituents give 1,3-cis diastereomers. Functional groups in the C-2 side chain of the dioxolane ring may hinder cyclization by complexation with the promoter.     

Cationic ring‐opening polymerization behavior of a five‐membered cyclic thiocarbonate having a spiro‐linked adamantane moiety

This work deals with the synthesis and cationic ring‐opening polymerization behavior of a novel five‐membered cyclic thiocarbonate bearing a spiro‐linked adamantane moiety, tricyclo[3.3.1.1^3,7]decane‐2‐spiro‐4′‐(1′,3′‐dioxolane‐2′‐thione) ( TC2 ). The cationic ring‐opening polymerization of TC2 did not proceed with trifluoromethanesulfonic acid, methyl trifluoromethanesulfonate, triethyloxonium tetrafluoroborate (Et₃OBF₄), boron trifluoride etherate (BF₃OEt₂), titanium tetrachloride, or methyl iodide as the initiator, presumably because of the steric hindrance of the adamantane moiety. However, the cationic ring‐opening copolymerization of TC2 with five‐ or six‐membered cyclic thiocarbonates, that is, 1,3‐dioxolane‐2‐thione, 1,3‐dioxane‐2‐thione, 5‐methyl‐1,3‐dioxane‐2‐thione, or 5,5‐dimethyl‐1,3‐dioxane‐2‐thione, initiated by BF₃OEt₂ or Et₃OBF₄, proceeded to afford the corresponding copolymer via a selective ring‐opening direction. The increase in the feed ratio of TC2 in the copolymerization increased the unit ratio derived from TC2 in the copolymer; however, the molecular weight of the copolymer decreased. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 699–707, 2003     

Titanium complexes based on aminodiol ligands for the ring‐opening polymerization of ε‐caprolactone,rac‐β‐butyrolactone,and trimethylene carbonate

Several titanium complexes based on aminodiol ligands were tested as initiators for the ring‐opening polymerization (ROP) of ε‐caprolactone under solution and bulk conditions. All complexes were found to be efficient under both conditions. For bulk polymerization at 70 °C, high activities were observed (113.3–156.2 g_poly mmol_cat^?1 h^?1) together with controlled molar mass distribution. Kinetic studies revealed controlled polymerization, and the chain propagation was first order with respect to monomer conversion. One complex was also tested for the ROP of rac‐β‐butyrolactone and the end‐group analysis suggested that ring opening occurs through acyl‐oxygen bond cleavage via coordination–insertion mechanism. The microstructure analysis of polymer by ¹³C NMR indicates atactic polymer. Another complex was also found to be efficient initiator for the ROP of trimethylene carbonate under solution and bulk conditions. Again, end‐group analysis suggests coordination–insertion mechanism. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Ab initio study on the mechanism of cycloaddition reaction between H<Subscript>2</Subscript>Si=Si: and formaldehyde

The mechanism of the cycloaddition reaction between singlet H₂Si=Si: and formaldehyde has been investigated with the CCSD(T)//MP2/6-31G* method. From the potential energy profile, it could be predicted that the reaction has three competitive dominant reaction pathways. The reaction rules presented is that the 3p unoccupied orbital of the Si: atom in H₂Si=Si: inserts the π orbital of formaldehyde from the oxygen side, resulting in the formation of an intermediate. Isomerization of the intermediate further generates a four-membered ring silylene (the H₂Si–O in the opposite position). In addition, the [2+2] cycloaddition reaction of the two π-bonds in H₂Si=Si: and formaldehyde also generates another four-membered ring silylene (the H₂Si–O in the syn-position). Because of the unsaturated property of the Si: atom in the two four-membered ring silylenes, the two four-membered ring silylenes could further react with formaldehyde, generating two silicic bis-heterocyclic compounds. Simultaneously, the ring strain of the four-membered ring silylene (the H₂Si–O in the syn-position) makes it isomerize to a twisted four-membered ring product.     

Cationic Polymerization of Cyclic Sulfides

Abstract

The mechanism of the cationic polymerization of several thietanes and of propylene sulfide under the influence of triethyloxonium tetrafluoroborate in methylene chloride is described. The thietane polymerizations stop at limited conversions because of a termination reaction occurring between the reactive chain ends (cyclic sulfonium salts) and the sulfur atoms of the polymer chain. The maximum conversions obtained under identical conditions differ markedly for the different monomers. Ratios of rate constants of propagation (k_p) to rate constants of termination (k_t) have been calculated. The differences in k _p/k_t. values for the different monomers are explained in terms of differences in basicity and differences in steric hindrance of the monomers compared to the corresponding polymers. In the case of propylene sulfide it is proposed that the main termination reaction is the formation of 12-membered ring sulfonium salts by an intramolecular reaction of the third sulfur of the growing polymer chain with the reactive chain end (three-membered ring sulfonium salt). This terminated polymer is able to reinitiate the polymerization, for example, by reaction of a monomer molecule at the exocyclic carbon atom of the sulfonium salt function. The cyclic tetramer of propylene sulfide is formed in this reaction. After complete polymerization, formation of cyclic tetramer continues, probably via a backbiting mechanism. In methylene chloride as solvent, the absolute value of the rate constant of propagation for 3,3-dimethylthietane changes with changing concentration of initiator and by adding different amounts of indifferent electrolyte to the reaction mixture. From these changes, and assuming that the value of the dissociation constant of the growing chain-ends is close to values of dissociation constants of low molecular weight sulfonium salts, separate rate constants for propagation via free ions and ion-pairs were calculated. The propagation constant of free ions is about 70 times higher than that of ion pairs in methylene chloride at 20°C. Free ions and ion pairs are nearly equally reactive in nitrobenzene.     

Further discussion of the cyclopolymerization of acrylic anhydride in terms of ring size control

Radical cyclopolymerization of acrylic anhydride (AA) was conducted under various polymerization conditions to yield highly cyclized polymer, and the content of the five-membered ring of cyclic poly-AA obtained was examined in detail. Five-membered ring formation was favored with increased solvent polarity, raised polymerization temperature, and decreased monomer concentration; the ring size of the cyclic structure could be controlled freely by choosing appropriate polymerization conditions. In addition to these results, the rate of polymerization and the molecular weight of the polymer were reduced under polymerization conditions where the five-membered ring formation was favored. Finally, a mechanistic discussion is given in order to interpret these results; a reaction scheme for propagation based on polymerization equilibrium is proposed.     

Amphiphilic polymer gel electrolytes. II. Influence of the ethylene oxide side‐chain length on the gel properties

Amphiphilic polymers consisting of copolymethacrylates carrying about 26 wt % ethylene oxide [(EO)_n] side chains of different lengths were used as matrices in gel electrolytes. The gel electrolytes were composed of 30 wt % copolymer and 70 wt % 1 M LiPF₆ in a mixture of ethylene carbonate and γ‐butyrolactone (2/1 w/w). The coordination of lithium ions by the (EO)_n side chains in competition with the solvent was studied by Raman spectroscopy. A significantly stronger lithium coordination was observed when the gel electrolyte was based on a copolymer carrying (EO)₉ units in comparison with copolymers having (EO)₁, (EO)₂, and (EO)₄ units. Despite the observed stronger lithium coordination by (EO)₉ units in the gel, the ion conductivity was not significantly lower with respect to the gels based on the other copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1519–1524, 2001     

CuMgAlO_x复合氧化物催化甲醇乙醇Guerbet反应:M~(2+)/Al~(3+)比的影响

以类水滑石为前驱体,通过调控M~(2+)/Al~(3+)比制备了系列具有不同表面性质的MgAlO_x(MA)和CuMgAlO_x(CMA)催化剂,并分别应用于甲醛乙醛缩合反应(甲醇乙醇Guerbet反应的第二步反应)和甲醇乙醇Guerbet反应。采用NH_3/CO_2-TPD、XPS、H_2-TPR和H_2-TPD技术对催化剂表面酸碱性以及铜物种的性质进行了表征。结果表明,甲醇乙醇Guerbet反应性能与催化剂表面Cu~0比表面积和中强碱数目有关,提高Cu~0比表面积有利于甲醇乙醇脱氢生成甲醛和乙醛,增强中强碱数目能促进甲醛乙醛缩合反应。     

Aluminate and Magnesiate Complexes as Propagating Species in the Anionic Polymerization of Styrene and Dienes

The influence of MgR₂ and AlR₃ additives on alkyllithium initiators in the anionic polymerization of butadiene has been investigated in non polar solvents. A strong decrease of the diene polymerization rate in the presence of the two Lewis acids was observed, similarly to that observed in the retarded anionic polymerisation of styrene. With n,s-Bu₂Mg, the percentage of 1,2 vinyl units increases with the [Mg]/[Li] ratio. This behavior is specific to magnesium derivatives bearing secondary alkyl groups and likely results from the additional complexation of lithium species by free dialkylmagnesium and/or a 1,4- to 1,2- chain end isomerization process during chain exchanges between polybutadienyl active chains and dormant ones attached to magnesium species. These reversible exchanges also lead to the formation of one supplementary chain by initial dialkyl magnesium which acts as reversible chain transfer agent. On the contrary with the R₃Al/RLi systems the number of chains is only determined by the concentration of initial alkyllithium and no modification of the polybutadiene microstructure compared to lithium initiators (1,4 units = 80%) is noticed. Dialkyl magnesiate complexes with alkali metal derivatives (i.e. alkoxide) are also able to influence the stereochemistry of the styrene insertion during the propagation reaction. Polystyrenes with different tacticities ranging from predominantly isotactic (85% triad iso) to syndiotactic (80% triad syndio) can be obtained with these initiators.     

Ring-Opening polymerization of ε-caprolactone by rare earth coordination catalysts. I. Characteristics,kinetics, and mechanism of ε-caprolactone polymerization with nd(acac)3.3H2O-ALET3 system

Ring-opening polymerization of ε-caprolactone has been carried out by using rare earth coordination catalysts for the first time. The rare earth compounds, RE(acac)₃.3H₂O, Nd(P₂₀₄)₃, Nd(P₅₀₇)₃, Nd(naph)₃, Nd(BA)₃.2H₂O, etc. (where RE = La, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Lu, Y; acac = acetylacetone; BA = benzoylacetone), combined with trialkyl aluminum, greatly increased the degree of conversion and the molecular weight of poly(ε-caprolactone) (PCL). The influence of reaction conditions on the polymerization of ε-caprolactone catalyzed by the Nd (acac)₃.3H₂O-AlEt₃ system has been examined in detail. The kinetics indicates that the polymerization rate has the first-order in monomer and a half-order in catalyst. The overall activation energy of the ring-opening polymerization amounts to 59.4 kJ/mol. By IR and UV-Vis spectra, ¹H- and ¹³C-NMR data, it is assumed that the ring-opening polymerization of ε-caprolactone catalyzed by the Nd(acac)₃.3H₂O-AlEt₃ system proceeds via complexation of monomer to catalyst, acyl-oxygen cleavage insertion propagation mechanism. © 1994 John Wiley & Sons, Inc.     

Synthesis and polymerization of a novel perfluorinated monomer

Perfluoro(5-methylene-2,2-dimethyl-1,3-dioxolane) (1) was synthesized by utilizing a direct fluorination reaction. Compound 1 was an entirely novel monomer with difluoromethylene at position 5 on the dioxolane ring as an unprecedented polymerization site. It successfully polymerized with tetrafluoroethylene to afford copolymers, which had T_g values in the range of 60-90 °C. The content of monomer 1 in the obtained polymers was less than 20 mol%, which seemed insufficient for giving various unique properties to polymers. However, each polymer was expected to be a superior material because of their advanced thermal stability. Comparison with copolymers of 2,2-bis(trifluoromethyl)-4,5-difluoro-1,3-dioxole and tetrafluoroethylene is also discussed.