自来水用橡胶软管中铅的析出分析

研究生活饮用水用橡胶软管中铅析出规律,选择3款橡胶软管,测定铅含量,并在自来水中分析不同浸泡时间以及普通浸泡温度(22、40、60、80、100℃)条件下铅析出量。结果表明,橡胶软管3#、1#、2#的铅含量依次降低,相同条件下铅析出量也依次降低;同一样品随着浸泡次数的增加,铅析出量呈现下降趋势;随着温度的升高,铅析出量呈现增加趋势,析出速率也在增加,铅含量高的橡胶软管铅析出量也高,铅析出量随着浸泡次数的增加而逐渐降低,随着浸泡温度的提高而增高。     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

Ca2+-Mg2+-Zn2+体系在水溶性聚磷酸铵溶液中螯合规律的研究

近年来,水溶性聚磷酸铵在液体肥料和复合肥料的领域受到了广泛的关注,并在发达国家中得到了大面积的推广及应用。在pH值为5.5~8.0、温度为278.15 K~323.15 K的条件下,本文采用滴定法研究Ca_²⁺-Mg_²⁺-Zn_²⁺体系在聚磷酸铵溶液中的螯合规律。实验结果表明：相同质量分数的聚磷酸铵溶液对金属离子的螯合量会随着体系中Ca_²⁺、Mg_²⁺、Zn_²⁺的摩尔浓度的变化而变化;随着温度的升高而逐渐降低;随着pH的增加而逐渐增加;随着聚合度的升高而逐渐增加。采用傅里叶红外光谱对聚磷酸铵和A₁B₃C₃体系的螯合物进行表征。     

Bi2O3掺杂对Ag(Nb0.8Ta0.2)O3陶瓷结构和介电性能的影响

本文研究了Bi₂O₃掺杂对Ag(Nb_0.8Ta_0.2)O₃陶瓷的结构和介电性能的影响。X射线衍射(XRD)结果表明,Bi₂O₃的掺杂可以使陶瓷中Ag⁺被还原并析出,且银析出的量随Bi₂O₃掺杂量的增加而不断增加,这可能源自于Bi³⁺对Ag⁺的取代。在一定范围内增大Bi₂O₃掺杂量可提高Ag(Nb_0.8Ta_0.2)O₃陶瓷的室温介电常数,降低介电损耗,并使温度系数向负值方向移动。当Bi₂O₃的掺杂量约为3.5wt%时,样品具有较大的介电常数(ε=672)和较小的介电损耗(tanδ=7.3×10^-4)。     

酸性AlCl3-BMIC离子液体中的铝阳极溶解

采用线性扫描伏安法研究了Lewis 酸性AlCl₃-BMIC (BMIC: 1-butyl-3-methylimidazolium chloride)离子液体中铝电极的溶解. 铝电极在阳极极化时出现了钝化现象, 钝化是由于在铝电极表面形成了固体AlCl₃钝化膜造成的. 铝的电化学溶解过程可以依次分为三个区: 电化学控制区、过渡区和钝化区. 在电化学控制区, 铝的电化学溶解速率随着电位的正移而逐渐增加; 在过渡区, 由于电极表面AlCl₄^-和Al₂Cl₇^-浓度发生改变而析出固体AlCl₃使得铝电化学溶解速率随着电位的正移而逐渐减小; 当钝化膜形成之后, 铝的电化学溶解速率不再随着电位的正移而发生改变, 铝溶解进入钝化区. 增加搅拌、升高温度、降低离子液体AlCl₃摩尔分数都可以增加铝溶解阳极极限电流密度.     

南翼山油田卤水低温结晶过程研究

自行设计搭建了一套油田水低温冷冻实验设备, 使用该设备研究了南翼山油田原始卤水在-18.90 °C到-30.90 °C范围内的结冰析盐过程, 精确测量了油田水随温度降低第一种和第二种固相的析出温度. 化学分析得到了该温度范围内Ca²⁺、Mg²⁺、K⁺、Cl^-、B₂O₃、Na⁺六种常量组分在液相中的含量变化趋势. 使用低温X射线衍射法对原始卤水在低温下得到的固相进行了初步的鉴定, 并对南翼山油田水的低温相变过程进行了实时监测. 实验结果表明: 南翼山油田水降温至-19.10 °C析出第一种盐NaCl·2H₂O, 降至-23.55 °C同时析出冰和NaCl·2H₂O.     

低温合成四方相BaTiO3及其压电催化性能

基于淀粉糊化机制低温合成了四方相BaTiO₃粉体。采用扫描电子显微镜、透射电子显微镜、X射线衍射、傅里叶变换红外光谱、紫外可见吸收光谱、X射线光电子能谱对合成粉体的形貌、物相进行表征;在超声条件下,以系列典型染料为降解对象测试BaTiO₃压电催化性能。结果显示,煅烧温度为600℃时即可获得四方相BaTiO₃粉体,且随着温度的提升,结晶度逐渐增加;当煅烧温度为700℃时,合成的BaTiO₃粉体尺寸分布均匀,分散度良好,呈现类立方体状;在超声驱动下,BaTiO₃降解罗丹明B、刚果红、甲基橙染料时均展现出良好的效果,反应速率常数分别为1.090×10^-2、1.113×10^-2、1.084×10^-2 min^-1,并以降解刚果红为对象揭示其压电催化的机理,即空穴和超氧自由基是降解过程中的主要反应物质。     

热处理温度对铬掺杂二氧化钛表面结构和性质的影响

采用溶胶-凝胶法制备了铬掺杂二氧化钛(Cr-TiO₂), 并对经过不同温度烧结的Cr-TiO₂的结构、吸收光谱及样品中铬的氧化态等进行了表征. 实验结果表明, 在不高于723 K的温度烧结后, 铬以Cr^3＋的氧化物和Cr^6＋的铬酸盐或重铬酸盐的形式存在于TiO₂表面. 随着热处理温度的提高, Cr^6＋的含量逐渐增多. Cr-TiO₂在可见区400～550 nm的吸收带是由Cr^3＋的⁴A₂→⁴T₁跃迁和O→Cr^6＋的1t₁→2e电荷转移等引起的, 620～800 nm的吸收则是Cr^3＋的⁴A₂→⁴T₂跃迁的结果. 前者随着烧结温度的升高而增强, 后者则随着温度升高而下降.     

纳米固体超强酸SO42-/Fe2O3的制备及其催化合成乙酸乙酯

将Fe₂O₃纳米粉体经一定浓度的H₂SO₄浸泡活化后制成纳米固体超强酸SO₄^2-/Fe₂O₃,将其用于催化合成乙酸乙酯以考察其活性。利用均匀设计分析了超强酸制备过程及酯化反应过程中各因素的影响,研究结果表明较好的制备条件是:H₂SO₄浓度:2.5mol·L^-1;浸泡时间:1h;活化温度:167℃;活化时间:1h,此时获得的固体超强酸SO₄^2-/Fe₂O₃的粒径小于50nm。当催化剂用量为冰乙酸质量的5%,n(乙醇)∶n(冰乙酸)为3∶1,反应3.5h后乙酸的转化率高于80%。该催化剂经H₂SO₄溶液浸泡、活化再生后可重新使用,推断出其酸强度H₀<-14.5。     

活性炭催化碳酸二甲酯水解行为的研究

以无氯Cu/AC催化剂中活性炭载体为研究对象,对活性炭上DMC水解反应条件进行了考察,并通过Boehm滴定法和XPS对活性炭上DMC水解活性位点进行了分析。结果表明,温度的升高和水含量的增加对DMC水解有较大的促进作用,较高的压力和CO₂气氛对DMC水解有一定的抑制作用,甲醇量和CO、O₂、N₂气氛对DMC水解影响较小。不同条件处理的活性炭表面基团种类、数量均有较大变化,HNO₃处理使活性炭碱性基团含量下降,羧基等酸性含氧官能团含量明显增加,总酸量最高可达1.88 mmol·g^-1;先HNO₃后NaOH处理的活性炭上酸性基团含量大量减少,表面碱性基团含量则有较大提高,总碱量最高可达1.69 mmol·g^-1。特别地,活性炭表面碱性基团是催化DMC水解的活性位点,在活性炭碱性基团含量由0.16增加到1.69 mmol·g^-1的过程中,DMC水解程度由2.5%增加到了31.7%,而酸处理可以有效降低活性炭表面碱性基团含量,抑制其催化DMC的水解性能。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.