Preparation and properties of aromatic polypyrazoles from linear bis-β-diketones and aromatic dihydrazines

The cyclopolycondensation of linear bis-β-diketones with aromatic dihydrazines in dimethyl sulfoxide at 100–150°C produced a series of aromatic polypyrazoles with inherent viscosities up to 0.6 dL/g. All the polymers were highly soluble in a wide range of solvents, which included tetrahydrofuran and chloroform. The polypyrazoles showed excellent thermal stability with 10% weight loss at 410–490°C in air and nitrogen atmosphere.     

Polypyrazoles from aromatic dipropynones and aromatic dihydrazines

Two types of polypyrazoles, unsubstituted and phenylated, were prepared by a novel synthetic route involving the cyclopolycondensation of aromatic dihydrazines and aromatic dipropynones. The polymers had inherent viscosities as high as 1.05 dL/g and were soluble in N, N-dimethylacetamide, chloroform (phenylated polypyrazoles only), and sulfuric acid. The polymers exhibited glass transition temperatures ranging from 202 to 266°C and polymer decomposition temperatures (10% weight loss) as measured by thermogravimetric analysis of 400–500°C in air and 465–512°C in nitrogen. The synthesis and characterization of several polypyrazoles are discussed.     

Synthesis and characterization of phenyl-pendant aromatic polythiazoles from bis-α-bromophenylacetyl compounds and dithioamides

Novel phenyl-pendant aromatic polythiazoles having inherent viscosities of 0.3–1.3 dL/g were synthesized by the solution polycondensation of bis[4-(α-bromophenylacetyl)phenyl] ether with aromatic dithioamides or dithiooxamide in dimethylformamide at 60°C. The polythiazole having m-phenylene linkage was readily soluble in chloroform and m-cresol, and transparent flexible film could be cast from the chloroform solution. Glass transition temperatures of these polythiazoles were in the range of 210–250°C. They started to decompose at about 500°C in air with 10% weight loss being recorded at around 570°C.     

On the oximation of diaryl-β-diketones

The reaction of asymmetrically substituted β-diketones with hydroxylamine to give 3,5-diarylisoxazoles has been re-investigated, and has been found to occur with a low degree of site-selectivity unless steric effects are operating. The isoxazole that has the more electron-deficient aryl group in position 3 is formed preferentially when the reactions are run with hydroxylamine hydrochloride. When the reactions are performed in a neutral medium, a reversed site-selectivity is observed. Steric effects have a much stronger influence on the selectivity of the reaction: when a substituent is present in the ortho position(s) of the phenyl ring, the heterocycle bearing the ortho-substituted phenyl group in position 5 is obtained as the sole product both in acidic and in neutral medium.     

Synthesis of polypyridazinophthalazinediones from diacetylphthalic acids and aromatic dihydrazines

The cyclopolycondensation of two diacetylphthalic acids with aromatic dihydrazines produced a series of new high-molecular-weight polypyridazinophthalazinediones with pendant methyl groups. The polymers were best prepared in m-cresol at 100°C and, after isolation, were readily soluble in dichloroacetic acid and m-cresol. Clear yellow films could be cast from m-cresol solutions and thermogravimetric analysis of all the polymers showed a 10% weight loss at 455–;505°C in nitrogen.     

Synthesis of polydihydropyridazinones from bis(3-benzoylpropionic acids) and aromatic dihydrazines

A new class of polydihydropyridazinones has been synthesized by the solution cyclopolycondensation in m-cresol of 4,4′-oxy- and 4,4′-ethylenebis(3-benzoylpropionic acids) with aromatic dihydrazines such as bis(4-hydrazinophenyl) sulfone and bis(4-hydrazinophenyl)methane. The polymers having inherent viscosities of 0.2–0.4 were highly soluble in a wide range of solvents including m-cresol, N,N-dimethylacetamide, and pyridine. Thermogravimetric analysis of the polydihydropyridazinones showed initial weight losses commencing at 290–350°C in both air and nitrogen.     

Study on synthesis of fluotochloroalkyl β-diketones

Several fluorochloroalkyl β-diketones were synthesized from Claisen condensation of ethyl difluorochloroacetate with methyl ketone in the presence of sodium ethoxide. The fluorinated methyl ketones, which were used as one of the reactants in the Claisen condensation were synthesized by the following methods, namely: the addition of methyl Grignard reagent to ethyl difluorochloroacetate; the addition of bis(m-chlorotetrafluorophenyl) cadmium to acetyl chloride and the hydrolytic decomposition of β-keto ester.     

Preparation and antibacterial activity of aromatic derivatives of β-aminopropionic and γ-aminobutyric acid

Ten aromatic derivatives of β-aminopropionic acid and γ-aminobutyric acid were prepared.Their compositions and structures were identified by elemental analysis,IR,and 1H NMR.They have been examined for their antibacterial action against Staphylococcua aurens and Escherichia coli.These compounds showed higher activity than the aromatic derivatives of ct-amino acid which were reported previously.The general conclusion to be drawn is that the distance between amino and carboxylic group in these molecules could affect their antibacterial activity.Furthermore,those compounds with p-methyl substituent in phenyl ring exhibit higher activity than the others,and all the compounds exhibit higher activity against Escherichia coli and against Staphylococcua aureus.     

Synthesis of polypyridazinophthalazinediones from dibenzoylphthalic acids and aromatic dihydrazines

A novel class of polypyridazinophthalazinediones has been synthesized by the solution cyclopolycondensation in m-cresol of dibenzoylphthalic acids with aromatic dihydrazines such as bis(4-hydrazinophenyl)methane and bis(4-hydrazinophenyl) sulfone. The polyheterocycles derived from 4,6-dibenzoylisophthalic acid, which had inherent viscosities of up to 0.5, were soluble in m-cresol and hot dichloroacetic acid, whereas the polymers from 2,5-dibenzoylterephthalic acid were practically insoluble in organic solvents. Thermogravimetric analyses showed that all the polymers underwent weight losses of 10% at 490–520°C in both air and nitrogen.     

A new synthesis of 3(2H)-furanones from acetylenic β-diketones

Thermal cyclization of 1,5-diarylpent-1-yne-3,5-diones led to the formation of 2-benzyliden-5-aryl-3(2H) furanones as well as 2,6-diaryl-4H-pyran-4-ones as minor products. The structure of the furanones was established from their ir, ¹H nmr and mass spectral data. Their reaction with hydrazine hydrate gave pyrazole derivatives.     

Polypyrazolinones from aromatic di(propynoic ester)s and aromatic dihydrazines

Novel polypyrazolinones with inherent viscosities ranging from 0.12 to 0.44 dL/g were prepared by the Michael-type nucleophilic addition-cyclization of various dihydrazines with 3,3′-(1,3- or 1,4-phenylene)bis(ethyl propynoate) (1,3- or 1,4-PEP) and 3,3′-(1,4-phenylene)bis(phenyl propynoate) (1,4-PPhP) in N-methylpyrrolidone (NMP) solution at 25–110°C. The polymers exhibited moderate thermal stability with initial weight loss in air about 200°C and in nitrogen about 300°C (TGA). No apparent T_g′s were observed by DSC analysis. The synthesis and characterization of the polypyrazolinones is discussed.     

Preparation,characterization and properties of β-chitin and N-acetylated β-chitin

Free amino groups in β-chitin from squid pen were acetylated to obtain N-acetylated β-chitin. After careful control of degree of acetylation, thermal and mechanical properties of β-chitin and N-acetylated β-chitin were compared. The structural differences of β-chitin and N-acetylated β-chitin were characterized by Fourier transform infrared (FTIR) and wide-angle x-ray diffraction (WAXD) analysis. The results indicated that the crystallinity of N-acetylated β-chitin was higher than that of β-chitin and N-acetylated β-chitin exhibited characteristics similar to α-chitin. Equilibrium water content (EWC) of β-chitin reached to about 50% and this hydrophilic nature was assumed to be caused by a relatively weak hydrogen bonding force of β-chitin with parallel main chains. On the other hand, EWC of N-acetylated β-chitin was 40% due to the introduction of ordered structure. β-chitin and N-acetylated β-chitin have the tensile strength of 0.4 and 0.7 Mpa in the swollen state, respectively. Viscoelastic properties and thermal relaxation behaviors were investigated by dynamic mechanical thermal analysis (DMTA). DMTA spectra of these samples showed that α-transition peaks of β-chitin and N-acetylated β-chitin were observed at 170 and 190°C, respectively. These relaxation peak maxima were assigned to be their glass transition temperature. In addition, a second relaxation peak of β-chitin resulting from acetamide groups was found at 112°C and a broad relaxation peak of N-acetylated β-chitin at around 81–100°C. As a result of thermogravimetric analysis, 10% weight loss temperatures of β-chitin and N-acetylated β-chitin were 270 and 285°C, respectively. © 1996 John Wiley & Sons, Inc.     

Reaction products of 2-aminobenzenethiol with some β-diketones

2-Aminobenzenethiol undergoes condensation reactions with several β-diketones (CH₃, CF₃ and C₆H₅ substituents) to form benzothiazolines. Conversion to benzothiazines and benzothiazoles occurs in some instances, as documented by the isolation and spectroscopic characterization of the products.     

Preparation of 5-sulfonylpyrimidines from β-keto, β-cyano-, and β-ethoxycarbonyl-β-sulfonylenamines

β-Keto-β-sulfonylenamines 2a,b reacted with benzamidine or guanidines to give 2,4-disubstituted 5-methanesulfonylpyrimidines 3a-d , whose methanesulfonyl groups were substituted by n-butyllithium or alkylmagnesium bromides to yield 2,4-disubstitued 5-alkylpyrimidines 6a-d. 2-Substituted 4-amino-5-sulfonylpyrimidines 7a,b, 8 and 2-substituted 5-benzenesulfonylpyrimidin-4-ones 9a,b were similarly obtained from β-cyano-β-sulfonylenamines 2c,d and β-ethoxycarbonyl-β-sulfonylenamine ( 2e ), respectively.     

Preparation and properties of polyamides from 2,8-phenoxathiin-bis-(γ-ketobutyric acid), 2,7-thianthrene-bis(γ-ketobutyric acid), and aromatic diamines

Aromatic-aliphatic polyamides containing phenoxathiin and thianthrene heterocyclic units were prepared by the direct polycondensation of 2,8-phenoxathiin-bis(γ-ketobutyric acid) ( I ) or 2,7-thianthrene-bis(γ-ketobutyric acid) (II) with various aromatic diamines in a triphenylphosphite-pyridine system. Prior to polymer synthesis two model diamides were prepared by condensing γ-keto acid I or II with p-toluidine. The model diamides and polyamides were characterized by spectral methods and elemental analysis. The polyamides, obtained in 56–90% yields, had inherent viscosities in the 0.82–1.1 dL/g range in concentrated H₂SO₄ at 30°C. The effect of heterocyclic units on polymer properties, such as solubility, crystallinity, and thermal stability has been discussed.     

Photodissociation of protonated β-diketones in the gas phase

The gas phase photodissociation spectra of four protonated β-diketones were obtained and compared with the absorption spectra of the corresponding ions in solution. Protonated 2,4-pentanedione was observed to undergo the photodissociation process [C₅H₉O₂]⁺ +hν → [CH₃CO]⁺ +C₃H₆O with a λmax at 276±10 nm compared with a solution absorption maximum at 286 nm. Protonated 2,4-hexanedione was observed to undergo the photodissociation processes [C₆H₁₁O₂]⁺ +hν → [CH₃CO]⁺ +C₄H₈O and [C₆H₁₁O₂]⁺ +hν → [C₂H₅CO]⁺ +C₃H₆O with a λmax at 279±10 nm compared with a solution absorption maximum at 288 nm. Protonated 3-methyl-2,4-pentanedione was observed to undergo the photodissociation process [C₆H₁₁O₂]⁺ +hν → [CH₃CO]⁺ +C₄H₈O with a λmax at 295±10 nm compared with a solution absorption maximum at 305 nm. Protonated 1,1,1-trifluoro-2,4-pentanedione was observed to undergo the photodissociation process [C₅H₆F₃O₂]⁺ +hν → CF₃H+[C₄H₅O₂]⁺ with a λmax at 273±10 nm compared with a solution absorption maximum at 288 nm. The [CH₃CO]⁺ and [C₂H₅CO]⁺ produced photochemically with the first three ions react to regenerate the protonated β-diketone leading to a photostationary state. Photodissociation of the protonated alkyl β-diketones is believed to occur from the protonated keto form, whereas photodissociation of protonated 1,1,1-trifluoro-2,4-pentanedione is believed to occur from the protonated enol form. Mechanisms for the observed photodissociation processes are proposed and comparisons with results from related techniques are presented.     

Structure and stability of aqua(bis-β-picoline)copper(II)-benzoate

Pseudochalcogeno Compounds. XI. On a New Type of Pseudochalcogeno-Modified Phosphates The preparation of pseudochalcogenophosphates of the general formulas [PO₃Y]^3? and [P₂O_7-nY_n]^4? (Y = C(CN)₂, n = 1, 2) is described. Chromatography of sodium salts, the formation of silver and calcium salts, characteristic IR and ³¹P-NMR data are discussed.     

Mass spectral studies of some β-diketones and their beryllium complexes

Detailed comparison of the fragmentation behavior of a series of beryllium β-diketonates with that of the corresponding series of β-diketones reveals a number of striking differences. A-typical fragmentations are observed for diketones and diketonates with trifluoromethyl and α-phenyl substituents.     

Preparation of 1,5-disubstituted 4-sulfonylpyrazoles, β-cyano-β-sulfonylenamines and 5-substituted 4-sulfonylisoxazoles from β-keto-β-sulfonylenamines

Reaction of β-keto-β-sulfonylenamines 1a,b with N-substituted hydrazines gave 1,5-disubstituted 4-sulfonylpyrazoles 2a-h in moderate yields, which were ring-opened on treatment with n-butyllithium to afford β-cyano-β-sulfonylenamines ( 3a,b,d-f ). 5-Substitued 4-sulfonylisoxazoles 6a-d were also prepared from 1a-d and hydroxylamine.