Structure and microporous formation of cellulose/silk fibroin blend membranes: Part II. Effect of post-treatment by alkali

Blend membranes (RCF1) were prepared from mixture solution of cellulose and silk fibroin (SF) in cuoxam by coagulating with acetone–acetic acid (4:1 by volume). The blend membranes were subjected to post-treatment with 10% NaOH aqueous solution, and their structure and properties were characterized by FT-IR, X-ray diffraction, DSC, SEM and DMTA. In previous work, cellulose/SF blend membranes (RCF2) prepared by coagulating with 10% NaOH aqueous solution formed a microporous structure, in which the SF as a pore former was almost completely removed from the membrane. However, when the blend membranes RCF1 were immersed in 10% NaOH aqueous solution for post-treatment, a strong hydrogen bonding between cellulose and SF inhibited the removal of SF. Although alkali is a good solvent for SF, the blend membranes RCF1 such obtained from cellulose and SF were alkali resistant. The crystallinity and the mean pore size of the blend membranes slightly decreased with increasing post-treatment time. This work provided a cellulose/silk blend membrane, which can be used under alkaline medium.     

海藻酸钠-硫酸软骨素共混膜的结构及性能研究

利用溶液共混法成功制备了新型生物膜材料-硫酸软骨素共混膜,通过红外光谱、X-射线衍射、原子吸收光谱和扫描电镜对共混膜的结构进行了表征,并测定了不同配比共混膜的抗张强度、断裂伸长率,吸水率,同时考察了介质pH值和离子强度对共混膜吸水率的影响。结果表明:共混膜中海藻酸钠、软骨素之间具有较强的相互作用和良好的相容性,共混膜具有良好的力学性能。作为一种潜在的生物材料可望在生物医学领域得到应用。     

Thermoreversible gelation of blend of poly(vinylidene fluoride) and poly(vinylidene fluoride-trifluoroethylene) in γ-butyrolactone solution

Thermoreversible gelation behavior of blend of poly(vinylidene fluoride) and poly(vinylidene fluoride-trifluoroethylene) in γ-butyrolactone solution was studied. Sol-gel transition temperature increased with the increase of polymer concentration, but was independent of the blend ratio of two polymers. An equation for gelation rate was derived, assuming that the gelation is a first-order reaction and that the gelation rate obeys an Arrhenius type. According to the equation, the growth index of gelation and supercooling temperature had a dominant effect on gelation rate. The growth index of gelation, which was calculated from the dependence of activation energy on the supercooling temperature in the isothermal gelation, varied with the blend ratio of two polymers. Growth index of gelation larger than 2 was obtained for the blend gels studied in this experiment. It may suggest that the multidimensional growth of gels occurs in such polymer blend solutions. X-ray diffraction and differential scanning calorimetry measurements showed existence of separate crystals due to each component of polymer in the blend gels. © 1996 John Wiley & Sons, Inc.     

聚醚砜/酚酞基聚醚砜共混相容性及凝胶特性研究

采用混合热焓法和稀溶液粘度法预测了聚醚砜/酚酞基聚醚砜体系相容性,并观察了聚醚砜/酚酞基聚醚砜共混制膜液的凝胶值与共混比的关系.聚醚砜/酚酞基聚醚砜为部分相容体系,其相容性与组成有关.共混制膜液的凝胶值受共混组成的影响,并非纯组分制膜液凝胶值的线性加和.     

PROPERTIES OF SILK FIBROIN/POLY(ETHYLENE GLYCOL)400 BLEND FILMS

The blend film of silk fibroin (SF) and poly(ethylene glycol)400 (PEG400) with a blend ratio of 2/1 (wt/wt) wasprepared simply by dropping a little PEG400 into the SF solution and then casting the mixed aqueous solution at 50℃. Theresulting film exhibited much better mechanical properties in the dry and wet state than SF itself, owing to theconformational change of SF in the blends from the random coil to the β-sheet structure and intermolecular hydrogen bondformation between SF and PEG400. Thermogravimetric analysis showed that the initial thermal decomposition temperatureof the blend film was 170℃, which was 80℃ lower than that of SF (250℃) and 20℃ higher than that of PEG400 (150℃),and indicated a Strong interaction between two components of the blend. No crystalline peaks were observed in the X-raydiffraction curve of the blend film. Cell culture test showed that SF/PEG400 was a suitable substrate for the growth of humanumbilical vein endothelial cells (HUVEC).     

纤维素/甲壳素共混膜的结构表征与抗凝血性能

以 6wt %NaOH 4wt%尿素为纤维素的新溶剂 ,采用溶液共混法制备出纤维素 甲壳素共混膜 ,为甲壳素在碱性溶液中制膜提供了新的方法 .红外光谱、X 射线衍射、扫描电镜和力学性能、抗凝血性能测试结果表明 ,共混膜中甲壳素含量低于 4 0wt%时 ,纤维素与甲壳素分子间具有良好的相容性 ;在纤维素中引入适量甲壳素可提高共混膜的抗张强度 ,共混膜的干、湿态抗张强度在甲壳素含量 10wt%时最大 ,其值分别为 89 1MPa和 4 3 7MPa ,比纯态纤维素膜的干、湿态抗张强度分别提高了 6 7%和 11 5 % ;甲壳素的引入可明显降低血小板在共混膜表面的粘附、凝聚与变性 ,增大共混膜的抗凝血参数 ,甲壳素含量达到 5 0wt%时 ,该共混膜具有良好的抗凝血性能     

磺化聚芳醚砜/磺化聚酰亚胺复合质子交换膜的制备与性能研究

利用溶液浇铸法制备了一系列双磺化型磺化聚芳醚砜/磺化聚酰亚胺(SPAES/SPI)复合质子交换膜.扫描电子显微镜(SEM)结果显示复合膜不存在明显的相分离,表明二者具有很好的相容性.由于SPI的引入,复合膜在甲醇中稳定性较纯SPAES具有大幅的提高,比Nafion112低得多的甲醇吸收率表明了这些复合膜具有比后者更低的甲醇透过率.复合膜显示了与单组分膜相类似的高温分解稳定性,磺酸基团的分解温度达到了290℃以上.复合膜显示出远高于纯SPAES膜的尺寸稳定性能,在130℃高温中200h处理后,所有的复合膜均保持了高的机械性能,而此时纯SPAES膜已经溶解于水中.而且由于两种磺化聚合物间的复合,复合膜维持了较高的IEC水平,显示了较高的质子导电率,在80%相对湿度时的质子导电率与Nafion112相近,而在水中的质子导电率均高于Nafion112.     

Correlations between the free-volume properties and the miscibility of chitosan/polar polymers blend membranes

The miscibility of chitosan (CS)/polar polymer blend membranes has been studied by positron annihilation and other methods. The miscibility of these two blend systems (CS/polyvinyl pyrrolidone (PVP) and CS/polyethylene glycol (PEG)) is good in the solution state due to the hydrogen interaction between the functional groups of the studied polymers. However, the miscibility of these two blend systems in the solid state is better in the CS/PVP system than in the CS/PEG system. The differences in miscibility of such two blend systems in the solid state were powerfully demonstrated with positron annihilation lifetime spectroscopy (PALS) methods. The CS/PEG blend system had much larger free-volume size and lower free-volume concentration. For their poorer interaction and phase separation fact, the molecules in the interfacial zone of the CS/PEG blend are less compact than the CS matrix. Therefore, the free-volume size in the interfacial zone was much larger than it in the CS matrix.     

Photoalignmentability of silsesquioxane-containing citraconimide and its solvent-induced surface enrichment in PMMA matrix

Photo-reactive polymer of silsesquioxane-containing citraconimide (SQ-CI) was synthesised and evaluated as a photoalignment layer for polymerisable liquid crystals (PLC). A generation mechanism of the anisotropy by the linearly polarised ultraviolet light was discussed by comparing optical retardation of SQ-CI with theoretical calculations using density functional theory. In addition, the SQ-CI and poly(methyl methacrylate) were blended for a model of unification of photoalignment layer and protection layer in liquid crystal display. The orientation of PLC on the blend film was dominated by the solvent used for the sample preparation of PMMA/SQ-CI blend. We found that the SQ-CI was enriched at surface of the blend film prepared from the ?-butyrolactone solution, while not in the case of the film prepared from cyclopentanone solution. The surface enrichment in the film prepared from ?-butyrolactone solution does not follow the conventional mechanism which is that the lower surface free energy component segregates to the blend surface, because the surface free energy of SQ-CI is higher than that of PMMA. Based on the result of solvent-annealing effect and photoalignmentability, we concluded that the mechanism of surface enrichment was explained due to the difference of affinity between the polymer and the solvent.     

Surface aggregation structure and surface mechanical properties of binary polymer blend thin films

During preparation of very thin polymer belnd films from a solution of polymers, the phase‐separated structures which are quite different from that observed for the bulk blend film was observed. From atomic force microscopic(AFM) observation, it is concluded that the surface undulation, which reflects the phase separated morphology of the blend system, is present. In the case of (polystyrene(PS)/poly(methyl methacrylate)(PMMA)) blend system, a large influence of end‐group chemistry on the surface morphology was observed. The phase identification of the (rubbery polymer/glassy polymer) binary blend thin films was successfully achieved by scanning vioscoelasticity microsopy(SVM).     

Temperature-sensitive membranes prepared from blends of poly(vinylidene fluoride) and poly(N-isopropylacrylamides) microgels

In this study, temperature-sensitive membranes were prepared by phase transition of the mixture of the temperature-sensitive poly(N-isopropylacrylamides) (PNIPAAM) microgels and poly(vinylidene fluoride). The results of Fourier transformed infrared spectrometer, X-ray photoelectron spectroscopy, elemental analysis, and scanning electron microscope photographs indicate that the PNIPAAM microgels are distributed more in the inner membrane than on the surface. The scanning electron microscope photographs reveal the blend membranes having porous surfaces with nanometer sizes and porous cross-sections with micrometer sizes. The addition of the PNIPAAM microgels is found to improve the porosity, the pore size, water flux, as well as to enhance the hydrophilicity and anti-fouling property of the blend membranes. The blend membrane shows temperature-sensitive permeability and protein rejection with the most dramatic change at around 32 °C which is the lower critical solution temperature of PNIPAAM, when water or bovine serum albumin solution flow through. Specifically, below 32 °C, the blend membrane shows a high protein rejection ratio which decreases with increasing temperature and a low water flux which increases with increasing temperature; above 32 °C, the blend membrane shows a low protein rejection ratio which decreases with increasing temperature and a high water flux which increases with increasing temperature.     

Preparation and Properties of Chitosan/Konjac Glucomannan Blend Fibers

Chitosan and konjac glucomannan (KGM) blend fibers were prepared by spinning their solution through a viscose‐type spinneret into a coagulating bath containing aqueous sodium hydroxide and ethanol. The structure and properties of the blend fibers were studied with the aids of infrared spectra (IR), scanning electron micrography (SEM) and X‐ray diffraction (XRD). The structure analysis indicated that there were strong interaction and good miscibility between the chitosan and KGM molecule which resulted from intermolecular hydrogen bonds. Mechanical properties and water‐retention properties were measured. Through controlling blend conditions, blend fibers can obtain better mechanical properties than the pure chitosan fiber. The water‐retention values (WRV) of blend fibers increase as the amount of KGM is raised. The fibers treated with alcoholic solution of acetic acid have good antibacterial activity to Staphylococcus aureus.     

高速搅拌对淀粉/聚乙烯醇共混物溶液成膜性能的影响

淀粉与聚乙烯醇（ＰＶＡ）溶液在高速搅拌下共混,可大大改善淀粉／ＰＶＡ共混薄膜的力学性能、透明性与耐水性,对其生物降解性有明显的影响．淀粉／ＰＶＡ共混体系在高速搅拌前后的光谱分析、显微观察、分子量及流变性能的测定表明,这些变化起因于高速搅拌增加了淀粉中直链淀粉的含量,同时提高了淀粉与ＰＶＡ共混溶液的稳定性,改善了淀粉／ＰＶＡ共混物薄膜的使用性能．     

Rheological behavior of cellulose/silk fibroin blend solutions with ionic liquid as solvent

The rheological behavior of cellulose and silk fibroin blend in 1-butyl-3-methylimidazolium chloride was studied. The data from the rheological results was analyzed to understand the microstructure of the blend solutions. The viscosity and dynamic modulus of the blend solution decreased with increasing ratio of silk fibroin. While comparing the experimental results with the calculated data from the log-additivity rule, it is revealed that zero-shear viscosity, dynamic modulus show positive–negative deviations and a typical continuous–discrete type of morphology could be imaged. At lower shear rate, the change of phase morphology took place at the ratio of about 0.5 volume fraction of cellulose. However, the blend solution showed positive deviations for all cellulose/silk fibroin blend ratios at high shear rate, which indicates that the dispersion of cellulose and silk fibroin was improved under shear stress. The properties of cellulose/silk fibroin blends observed by Fourier transform infrared spectroscopy and scanning electron microcopy agreed with the result from rheology.     

Surface structures and properties of polystyrene/poly(methyl methacrylate) blends and copolymers

Sum frequency generation (SFG) vibrational spectroscopy has been applied to study the molecular surface structures of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blends and the copolymer between PS and PMMA (PS-co-PMMA) in air, supplemented by atomic force microscopy (AFM) and contact angle goniometer. Both the blend and the copolymer have equal weight amounts of the two components. SFG results show that both components, PS and PMMA, can segregate to the surface of the blend and the copolymer before annealing, although PMMA has a slightly higher surface tension. Upon annealing both SFG results and contact angle measurements indicate that the PS segregates to the surface of the PS/PMMA blend more but no change occurs on the PS-co-PMMA surface. AFM images show that the copolymer surface is flat but the 1:1 PS/PMMA blend has a rougher surface with island like domains present. The annealing effect on the blend surface morphology has also been investigated. We collected amide SFG signals from interfacial fibrinogen molecules at the copolymer or blend/protein solution interfaces as a function of time. Different time-dependent SFG signal changes have been observed, showing that different surfaces of the blend and the copolymer mediate fibrinogen adsorption behavior differently.     

An intimate polycarbonate/poly(methyl methacrylate)/poly(vinyl acetate) ternary blend via coalescence from their common inclusion compound with γ‐cyclodextrin

In this study, we successfully report an intimate ternary blend system of polycarbonate (PC)/poly(methyl methacrylate) (PMMA)/poly(vinyl acetate) (PVAc) obtained by the simultaneous coalescence of the three guest polymers from their common γ‐cyclodextrin (γ‐CD) inclusion compound (IC). The thermal transitions and the homogeneity of the coalesced ternary blend were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The observation of a single, common glass transition strongly suggests the presence of a homogeneous amorphous phase in the coalesced ternary polymer blend. This was further substantiated by solid‐state ¹³C NMR observation of the T_1ρ(¹H)s for each of the blend components. For comparison, ternary blends of PC/PMMA/PVAc were also prepared by traditional coprecipitation and solution casting methods. TGA data showed a thermal stability for the coalesced ternary blend that was improved over the coprecipitated blend, which was phase‐segregated. The presence of possible interactions between the three polymer components was investigated by infrared spectroscopy (FTIR). The analysis indicates that the ternary blend of these polymers achieved by coalescence from their common γ‐CD–IC results in a homogeneous polymer blend, possibly with improved properties, whereas coprecipitation and solution cast methods produced phase separated polymer blends. It was also found that control of the component polymer molar ratios plays a key role in the miscibility of their coalesced ternary blends. Coalescence of two or more normally immiscible polymers from their common CD–ICs appears to be a general method for obtaining well‐mixed, intimate blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4182–4194, 2004     

电场条件下高分子共混物组分浓度梯度化的研究

研究了聚乙烯醇/聚丙烯酸高分子共混物水溶液中,共混物各组分在电场诱导条件下沿电场方向的浓度梯度分布情况.通过测定不同时刻PVA/PAA高分子共混物水溶液在电场的不同区域内的pH值,研究了电场诱导下共混物各组分沿电场方向的迁移过程.结果表明,PAAn-向电场正极迁移,同时由于浓差梯度,PVA向负极迁移,并形成浓度梯度分布.随时间的延长,高分子共混物的组分梯度程度逐渐加大.     

Degradation of polymer mixtures. VIII. Blends of poly(vinyl acetate) with poly(methyl methacrylate)

The degradation of blends of PVA and PMMA in the form of films cast from a common solution of the polymers has been studied by TVA, TG, and EGA (evolved gas analysis) for acetic acid. Volatile degradation products have been characterized by spectroscopic and GLC techniques. Molecular weight, spectral and thermal stability changes in PMMA extracted from partially degraded blends have been examined. These blends behave in a closely analogous manner to PVC-PMMA blends already investigated. The results suggest that the PMMA component of the heterogeneous blends is modified in two ways: (1) in a destabilization reaction series initiated by attack of acetate radicals generated in the PVA phase which migrate into the PMMA phase, and (2) in a stabilization reaction involving conversion of ester side groups to acid and subsequently to anhydride ring structures which act as blocking points for depolymerization. The rate of acetic acid production in the blend is less than in PVA degraded alone. The mechanism of degradation of PVA is reconsidered in the light of these results.     

Periodic porous stripe patterning in a polymer blend film induced by phase separation during spin-casting

A periodic striping pattern with microscale pore size is observed on the surface of thin films prepared by spin-casting from a polystyrene (PS) and polyethylene glycol (PEG) blend solution. The pattern is created by the convection generated by thermal gradients in the solution between the substrate and film solution during solvent evaporation, the radial flow of the spin-coated solution, and the primary and secondary phase separation of the PS and PEG solutions. The formation mechanism of the periodic porous stripe pattern is discussed, wherein the effects of the polymer blend weight ratio, polymer concentration, and drying rate on the formation of the periodic porous striping pattern are investigated using scanning electron and atomic force microscopy.     

甲壳素/聚氨酯共混物膜结构与性能的研究

采用共混的方法分别制备了丁羟型和聚醚型聚氨酯／甲壳素共混膜(HPCT和PPCT系列),研究了甲壳素加入量对共混膜力学性能、热稳定性、溶胀性和吸湿性的影响,讨论了共混物膜在不同环境条件下的降解性能。结果表明随着甲壳素含量的增加共混材料对水的亲和力和热稳定性提高,当甲壳素质量分数分别为0．15和0．10时HPCT系列和PPCT系列具有较佳的力学性能,HPCT和PPCT系列分别在pH=7．0和pH=4．7的环境中具有良好的降解性能。