等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

钛白粉载体对选择性催化还原脱硝催化剂性能的影响

钛白粉(TiO2)是钒钛类选择性催化还原(SCR)脱硝催化剂的载体,TiO2的晶型、比表面积、粒度、孔结构以及SO42-和P2O5含量直接影响所制备的SCR催化剂的性能。一般而言,TiO2的比表面积越大,以其制备的SCR催化剂的比表面积也越大,活性也较高;但对于纳米级TiO2,由于颗粒粒径太小,容易发生烧结,而且形成钒钛化合物,导致催化剂比表面积较载体明显下降,因而活性降低。锐钛型TiO2由于比表面积大和不易被硫化,较金红石型TiO2适合做载体。多孔结构的TiO2使得钒物种在载体表面处于高度分散状态,从而提高催化剂的活性。TiO2中本身含有的少量SO42-和P2O5有助于提高催化剂的性能。     

高性能燃料电池催化剂及其5kW常温常压免增湿电堆

应用高压有机溶胶法制得高性能的Pt/C催化剂.该催化剂的活性颗粒度达2.8 nm,活性比表面为450 m2/g,并进行了小批量试产(10 g).建立新型直接涂膜电极和免增湿技术,并制作了275 cm2的膜电极,设计和组装5 kW质子交换膜燃料电池电堆,以氢气为燃料,空气为氧化剂在常温常压免增湿条件下试运行,电堆连续运行10 h,输出功率基本稳定不变.     

Ni2P负载量对Ni2P/Ce-Al2O3催化剂结构及萘加氢性能的影响

采用程序升温还原法制备了一系列Ni₂P/Ce-Al₂O₃催化剂,考察了制备过程中Ni₂P负载量对催化剂结构及萘加氢饱和性能的影响。结果表明,Ni₂P负载量可调控活性组分Ni₂P与载体Ce-Al₂O₃之间的相互作用,进而调变催化剂的比表面积、Ni₂P粒径及催化剂活性位点数量。当Ni₂P负载量（质量分数）为17%时,催化剂具有较大的比表面积（40 m²/g）、较小的Ni₂P粒径（26.3 nm）和最多的活性位点数量（26.7 μmol/g）;同时,该催化剂萘转化率为95%,十氢萘选择性为76%,且活性稳定性良好,这主要归因于催化剂大的比表面积和高的活性位点数量为反应提供了更多的场所。     

纳米二氧化锆在甲醇合成催化剂Cu/Ga2O3/ZrO2中的作用

The introduction of mesoporous nanosize zirconia to the catalyst for methanol synthesis dedicates the nanosized catalyst and mesoporous duplicated properties. The catalyst bears the larger surface area, larger mesoporous volume and more uniform diameter, more surface metal atoms and oxygen vacancies than the catalyst prepared with the conventional coprecipitation method. The modification of microstructure and electronic effect could result in the change of the reduced chemical state and decrease of reducuction temperature of copper, donating the higher activity and methanol selectivity to the catalyst. The results of methanol synthesis demonstrate that the Cu^＋ is the optimum active site. Also, the interaction between the copper and zirconia shows the synergistic effect to fulfil the methanol synthesis.     

Fe1-xO基氨合成催化剂高活性机理初探

 由Fe1-xO催化剂的发现所引伸的新课题及其中潜在的科学暗示,特别是Fe1-xO基催化剂的高活性机理有待深入研究. 本文根据催化剂的还原性能和表面性质及其与催化活性的关联,从Fe1-xO的化学和物理性质出发,对Fe1-xO催化剂的高活性机理提出了一些初步认识. 催化剂前驱体由Fe3O4改变为Fe1-xO,首先使得催化剂的还原易于进行,还原温度降低,还原速度加快,还原出水量减少; 其次,改变了助催化剂在催化剂中的分布,从而改变了还原后催化剂的表面性质如表面酸覆盖度和碱覆盖度及其相对比例,形成了表面酸碱协同作用,促进了表面重构,降低了N2的脱附活化能,削弱了H2的强化学吸附. 这些变化导致催化剂活性提高,同时这些变化都是由Fe1-xO的化学和物理性质引起的,只有维氏体单独存在于催化剂中催化剂才具有高活性. 提出了H2的强化学吸附与催化剂表面酸碱度有关的观点.     

Growth of carbon nanotubes on the novel FeCo-Al2O3 catalyst prepared by ultrasonic coprecipitation

FeCo-Al_2O_3 catalyst was prepared by an ultrasonic coprecipitation (UC) method for the growth of carbon nanotubes (CNTs) from catalytic decomposition of methane. Its catalytic performance was compared with that of the FeCo-Al_2O_3 catalyst counterparts prepared by stepwise impregnation (I) and conventional coprecipitation (C) methods, respectively. The structure and properties of the catalysts and the CNTs as produced thereon were investigated by means of XRD, XPS, TEM and N_2 adsorption techniques. It was found that the catalyst prepared by the ultrasonic coprecipitation method was more active, and the yield and purity of the synthesized CNTs were promoted evidently. The XPS results revealed that there were more active components on the surface of the catalyst prepared by the ultrasonic coprecipitation method. On the other hand, N_2 adsorption demonstrated that the catalyst prepared by the ultrasonic coprecipitation method conferred larger specific surface area, which was beneficial to dispersion of active components. TEM images further confirmed its higher dispersion. These factors could be responsible for its higher activity for the growth of CNTs from catalytic decomposition of methane.     

Growth of carbon nanotubes on the novel FeCo-Al_2O_3 catalyst prepared by ultrasonic coprecipitation

FeCo-Al2O3 catalyst was prepared by an ultrasonic coprecipitation (UC) method for the growth of carbon nanotubes (CNTs) from catalytic decomposition of methane.Its catalytic performance was compared with that of the FeCo-Al2O3 catalyst counterparts prepared by stepwise impregnation (I) and conventional coprecipitation (C) methods,respectively.The structure and properties of the catalysts and the CNTs as produced thereon were investigated by means of XRD,XPS,TEM and N2 adsorption techniques.It was found that the catalyst prepared by the ultrasonic coprecipitation method was more active,and the yield and purity of the synthesized CNTs were promoted evidently.The XPS results revealed that there were more active components on the surface of the catalyst prepared by the ultrasonic coprecipitation method.On the other hand,N2 adsorption demonstrated that the catalyst prepared by the ultrasonic coprecipitation method conferred larger specific surface area,which was beneficial to dispersion of active components.TEM images further confirmed its higher dispersion.These factors could be responsible for its higher activity for the growth of CNTs from catalytic decomposition of methane.     

Pt-CeO2/SiO2催化剂用于室温湿空气中CO氧化反应

开发室温CO氧化催化剂的主要挑战是CO自中毒和慢的表面动力学,同时湿气的存在也可导致催化剂失活.本文开发了高活性CeO2促进的Pt基催化剂4%Pt-12%CeO2/SiO2,用于室温湿气(湿度10%?90%,25°C)中CO氧化反应,在低CO浓度(<500 ppm)和高CO浓度(>2500 ppm)时,CO转化率高于99%.优化了催化剂制备变量,如Pt和CeO2负载量、CeO2沉积方法、CeO2和Pt前驱体的干燥和焙烧条件.采用CO/H2化学吸附、O2-H2滴定、X射线衍射和BET比表面积测定表征了催化剂的表面特性,并将其与催化剂活性相关联.结果表明,CeO2沉积方法对催化剂活性影响显著,当用浸渍法沉积CeO2时,所得催化剂的反应速率(5.77μmol/g/s)比用沉积沉淀法(1.96μmol g?1 s?1)或CeO2嫁接法(1.31μmol g?1 s?1)制得催化剂的高3倍.O2-H2滴定结果表明,当用浸渍法沉积CeO2时,CeO2和Pt的紧密结合导致了催化剂的高活性.催化剂载体的选择也非常重要,硅胶负载的催化剂活性(5.77μmol g?1 s?1)是氧化铝负载的(1.05μmol g?1 s?1)5倍.当反应受内扩散控制时,催化剂载体的粒径和孔结构影响非常大.另外,CeO2和Pt前驱体的干燥和焙烧条件对催化剂活性的影响至关重要.当Pt和CeO2含量分别大于2.5和15 wt%时,所得催化剂在室温条件下活性高(TOF>0.02 s?1),稳定性好(反应15 h,CO转化率≥99%).     

Fe的分散程度对煤焦催化加氢气化的影响

在加压固定床反应器上研究了Fe催化剂在不同比表面积煤焦中分散性对催化加氢气化性能的影响,利用XRD、BET、H₂-TPR、FT-IR、TEM、拉曼光谱对煤焦及催化剂进行了分析表征。结果表明,煤焦活性位点和石墨化程度并非影响催化气化反应的唯一因素,而催化剂的分散性对反应影响更大。煤焦的比表面积越大,Fe催化剂在煤焦表面的分散更均匀,催化剂活性组分平均晶粒粒径越小,并可以促进煤催化加氢气化中间相产物Fe₃C的生成,甲烷收率越高。对于比表面积较高的900-char,在氢气压力为2 MPa,温度为750 ℃,Fe负载量为5%（质量分数）时,催化加氢气化甲烷收率可达53%。在900-char上考察了Fe催化剂负载量对催化加氢气化的影响,甲烷收率呈先增加后降低的趋势,Fe负载量存在饱和点。     

锰负载钛锆和钛锡复合氧化物催化剂烟气脱汞实验研究

采用共沉淀法制备了TiO_2、TiZr和TiSn载体,浸渍锰制备了10%MnO_2的MnTi、MnTiZr和MnTiSn催化剂。采用BET、XRD、H_2-TPR、FT-IR和XPS等对样品进行表征,并对三种催化剂进行固定床脱汞性能实验。结果表明,在100-300℃,MnTiZr和MnTiSn催化剂脱汞性能均优于MnTi催化剂,这归因于Sn和Zr的引入提升了催化剂比表面积和低温氧化还原性能增加了催化剂表面的酸性位点数量、高价态锰离子和O~*含量;在反应温度为150-300℃,MnTiSn催化剂脱汞效率均高于MnTiZr催化剂这是由于前者具有更好的氧化还原性能,表面具有更多含量的高价态锰离子、O~*含量和酸性位点数量;在Hg~0脱除过程中催化剂表面活性组分如高价态锰离子和O~*均消耗,参与了Hg~)氧化为Hg~(2+)的反应且MnTiSn催化剂表面活性组分的消耗量更多。