EFM phase investigation of the metal-organic film interface

Phase sensitive electrostatic force microscopy (EFM phase) investigations of semiconducting polymers, poly(3-hexylthiophene) (P3HT) and poly(9,9-dioctylfluorene) (F8), are described, aimed at understanding the metal/polymer interfaces. The electrostatic behaviour and potential distributions of the Au/polymer/Au structure under various biases with emphasis on top and bottom Au contacts are presented. We observe, by analysing EFM phase data, that the top and bottom contacts of Au can have drastic effects on the device performance. Moreover, differences in conductivity of conjugated polymers (P3HT > F8) are also reflected in EFM phase measurements, which correlate well with I-V measurements. Detailed analysis indicates that the influence of metal/film interfaces depends strongly on both the ability of charge transport properties of the organic films and the type of surface modification.     

An investigation on PAN-PVC-LiTFSI based polymer electrolytes system

Polymer-salt complex with poly(vinyl chloride) (PVC) and poly(acrylonitrile) (PAN) as host polymers blended with lithium bis-(trifluoro methanesulfonyl)imide, LiTFSI [LiN(CF₃SO₂)₂] as dopant salt were prepared in the form of thin film. Fourier transform infrared (FTIR) studies show the evidence of the complexation between PVC, PAN and LiTFSI. Ionic conductivity studies reveal that polymer electrolyte with 30 wt.% LiTFSI has the highest ionic conductivity of 4.39 × 10^− 4 S/cm at room temperature. The polymer electrolytes are also found to be stable up to 315 °C before they decompose. Thermal stability of the polymer electrolytes was also found to increase with increase in salt content. This was proven through thermogravimetric studies.     

Role of reactive gas in atmospheric plasma for cell attachment and proliferation on biocompatible poly ?-caprolactone film

This paper reports the surface modification of a biocompatible poly ?-caprolactone (PCL) film treated by atmospheric cold plasma (ACP) with reactive gases. The change in wettability and surface morphology of the PCL film after the plasma treatment with the reactive gases (Ar, H₂, N₂ and O₂) were determined using contact angle and surface roughness measurements. The chemical bonding states and molecular vibration modes of the activated organic groups on the polymer surface were examined by X-ray photoelectron spectroscopy and Fourier-transformation infrared techniques. The surface of the ACP-treated PCL films was also examined for their in vitro cell attachment and proliferation using human prostate epithelial cells (HPECs). The increase in the hydrophobicity of the Ar + H₂ plasma-treated PCL film resulted in a lower cell loading in the initial step of cell culture as well as a decrease in the level of cell attachment and proliferation compared with the pristine film. However, the hydrophilic properties of the Ar + N₂, Ar and Ar + O₂ plasma-treated PCL film improved the adhesion properties. Therefore, the Ar + N₂, Ar and Ar + O₂ plasma-treated PCL films showed a better cell distribution and growth than that of the pristine PCL film. The ACP-treated PCL film is potentially useful as a suitable scaffold in biophysics and bio-medical engineering applications.     

Friction and wear performance of some thermoplastic polymers and polymer composites against unsaturated polyester

Wear experiments have been carried out with a range of unfilled and filled engineering thermoplastic polymers sliding against a 15% glass fibre reinforced unsaturated polyester polymer under 20, 40 and 60 N loads and 0.5 m/s sliding speed. Pin materials used in this experimental investigation are polyamide 66 (PA 66), poly-ether-ether-ketone (PEEK) and aliphatic polyketone (APK), glass fibre reinforced polyamide 46 (PA 46 + 30% GFR), glass fibre reinforced polytetrafluoroethylene (PTFE + 17% GFR), glass fibre reinforced poly-ether-ether-ketone (PEEK + 20% GFR), glass fibre reinforced poly-phylene-sulfide (PPS + 30% GFR), polytetrafluoroethylene filled polyamide 66 (PA 66 + 10% PTFE) and bronze filled pofytetrafluoroethylene (PTFE + 25% bronze) engineering polymers. The disc material is a 15% glass fibre reinforced unsaturated polyester thermoset polymer produced by Bulk Moulding Compound (BMC). Sliding wear tests were carried out on a pin-on-disc apparatus under 0.5 m/s sliding speed and load values of 20, 40 and 60 N. The results showed that the highest specific wear rate is for PPS + 30% GFR with a value of 1 × 10⁻¹¹ m²/N and the lowest wear rate is for PTFE + 17% GFR with a value of 9.41 × 10⁻¹⁵ m²/N. For the materials and test conditions of this investigation, apart from polyamide 66 and PA 46 + 30% GFR polymers, the coefficient of friction and specific wear rates are not significantly affected by the change in load value. For polyamide 66 and PA 46 + 30% GFR polymers the coefficient of friction and specific wear rates vary linearly with the variation in load values.     

Study of optical band gap, carbonaceous clusters and structuring in CR-39 and PET polymers irradiated by 100 MeV O ions

Commercially purchased CR-39 and PET polymers were irradiated by 100 MeV O⁷⁺ ions of varying fluences, ranging from 1×10¹¹ to 1×10¹³ ions/cm². The effects of swift heavy ions (SHI) on the structural, optical and chemical properties of CR-39 and PET polymers were studied using X-ray diffraction (XRD), UV-visible spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The XRD patterns of CR-39 show that the intensity of the peak decreases with increasing ion fluence, which indicates that the semicrystalline structure of polymer changes to amorphous with increasing fluences. The XRD patterns of PET show a slight increase in the intensity of the peaks, indicating an increase in the crystallinity. The UV-visible spectra show the shift in the absorbance edge towards the higher wavelength, indicating the change in band gap. Band gap in PET and CR-39 found to be decrease from 3.87 to 2.91 and 5.3-3.5 eV, respectively. The cluster size also shows a variation in the carbon atoms per cluster that varies from 42 to 96 in CR-39 and from 78 to 139 in PET. The FTIR spectra show an overall reduction in intensity of the typical bands, indicating the degradation of polymers after irradiation.     

Damage formation in Ge during Ar and He implantation at 15 K

Ar⁺ and He⁺ ions were implanted into Ge samples with (1 0 0), (1 1 0), (1 1 1) and (1 1 2) orientations at 15 K with fluences ranging from 1×10¹¹ to 1×10¹⁴ cm⁻² for the Ar⁺ ions and fluences ranging from 1×10¹² to 6×10¹⁵ cm⁻² for the He⁺ ions. The Rutherford backscattering (RBS) technique in the channelling orientation was used to study the damage built-up in situ. Implantation and RBS measurements were performed without changing the target temperature. The samples were mounted on a four axis goniometer cooled by a close cycle He cryostat. The implantations were performed with the surface being tilt 7° off the ion beam direction to prevent channelling effects. After each 300 keV Ar⁺ and 40 keV He⁺ implantation, RBS analysis was performed with 1.4 MeV He⁺ ions.For both the implantation ions, there is about no difference between the values found for the damage efficiency per ion for the four different orientations. This together with the high value (around 5 times higher than that found in Si), gives rise to the assumption of amorphous pocket formation per incident ion, i.e. direct impact amorphization, already at low implantation fluences. At higher fluences, when collision cascades overlap, there is a growth of the already amorphized regions.     

Study of the fluence dependent interplay between laser induced material removal mechanisms in metals: Vaporization, melt displacement and melt ejection

Three quantitative methods, namely profilometry, high speed imaging and recoil momentum measurements using a ballistic pendulum, are used to determine the interplay of vaporization, melt displacement and melt ejection on nanosecond laser induced material removal. At low to moderate fluences (<7 J cm⁻²) material removal occurs via vaporization and melt displacement in aluminium. At high fluences (>7 J cm⁻²), material removal occurs predominantly via the explosive ejection of liquid droplets from the melt pool.     

A facile method for grafting of bisphenol A imprinted polymer shells onto poly(divinylbenzene) microspheres through precipitation polymerization

Core-shell structured polymers are usually prepared by “grafting to” or “grafting from” techniques, wherein polymer supports were first modified by vinyl bonds or initiators. Success can be immediate, but more often a learning curve needs to be traversed. In this paper, direct grafting bisphenol A imprinted polymer onto poly(divinylbenzene) microspheres through precipitation polymerization is introduced. The obtained microspheres were characterized by SEM, TEM, FTIR and BET. Firstly, mono-disperse poly(divinylbenzene) microspheres of 3 μm in size were prepared by precipitation polymerization. The solvent for grafting was then optimized and it was found that the mixtures of toluene and acetonitrile (30/70, v/v) were ideal choice from the image and structure analysis of the shells. Shells of different thickness (270-840 nm), depending on the concentrations of monomers in the precursor, were then directly grafted to the microspheres by a reactive, entropic capture mechanism. The recognition ability of the microspheres was evaluated by solid-phase extraction and clear selectivity showed toward bisphenol A. The leak of bisphenol A was not found after extraction and thus these core-shell structured imprinted polymers are believed to have potential applications in trace analysis area.     

Valence band and core level X-ray photoelectron spectroscopy of lead sulfide nanoparticle-polymer composites

Valence band and core level X-ray photoelectron spectroscopy (XPS) were used to probe lead sulfide (PbS) nanoparticle-polymer nanocomposites. Composite materials were prepared by trapping commercially available monodisperse 3 and 10 nm PbS nanoparticles in two polymers, the non-conducting polymer, polystyrene, and the conjugated polymer, poly(2-methoxy-5-(2′-ethyl-hexyloxy)-p-phenylene vinylene (referred to below as MEH-PPV). The nanocomposites prepared from commercial nanoparticles underwent oxidation, mainly to form lead sulfate. However, the narrow size distributions of the commercial nanoparticles allowed observation of distinct changes in the valence band from the 3 to 10 nm nanoparticles. Nanocomposites of 2-5 and 4-7 nm PbS nanoparticles were synthesized by growing the particles in poly(vinyl alcohol) (referred to below as PVA) and MEH-PPV, respectively. These composites both indicated the formation of lead sulfide nanoparticles. Furthermore, the XP spectra for the PVA/PbS composite displayed bonding between the PbS nanoparticles and the polymer while MEH-PPV showed no PbS-polymer bonding. The nanoparticles synthesized in MEH-PPV did not undergo oxidation. The particle size distributions of the synthesized nanoparticles were too broad to display size-dependent changes in the valence band.     

The effects of xenon ion irradiation on the photoluminesce behavior of poly(p-cresolformaldeyde)/diazonaphtoquinone thin films

In the present paper, we investigate the origin of photoluminescence (PL) and the changes in the optical properties: refractive index and absorption coefficient, in poly(p-cresolformaldeyde) and diazonaphtoquinone thin films irradiated with Xe ions. Films 400 nm thick have been irradiated with 800 keV Xe²⁺ ions in a fluence range from 10¹³ to 6 × 10¹⁵ Xe cm⁻². The structural modifications were followed by the techniques of nuclear reaction analysis, elastic recoil detection analysis, Rutherford backscattering, Fourier transform infrared and Raman spectroscopies. The PL behavior was characterised with 488 nm excitation wavelength. The pristine films show emission with maxima of the main bands located at 635, 720 and 830 nm. For fluences up to 10¹⁴ Xe cm⁻², the photoluminescence intensity increases with the irradiation fluence. The chain mobility lowering, characterized by the crosslinked structure, explains this behavior in organic systems. Other possible contribution for increasing of PL intensity, at these fluences, is the presence of oxygen trapped in the polymer chains by the dangling bonds. At intermediate and higher fluences, the photoluminescence starts to decrease. At fluences higher than 10¹⁴ Xe cm⁻², irreversible changes of the organic structure occur and they are characterized by large losses of oxygen and hydrogen, transforming the material into amorphous carbon films. The loss of photoluminescent behavior is associated with the light absorption characteristics of the amorphous carbon structure. This conclusion is supported by the observed increase of the refractive indexes and absorption coefficients, obtained in the infrared region, as well as by the Raman results. Also, the effect of irradiation modifying the refractive index in the infrared region suggests the application of these films as waveguide in this region of wavelength.     

The influence of UV-irradiation and support type on surface properties of poly(methyl methacrylate) thin films

Thin poly(methyl methacrylate) (PMMA) films were prepared by a solution casting on different supports (glass and aluminium plates with different gloss). UV-irradiation (λ = 254 nm) was used for polymer modification. Surface properties of PMMA were studied by contact angle measurements, attenuated total reflection infrared spectroscopy and optical microscopy. It was found that support type has no influence on surface properties of virgin PMMA, however, the changes in these properties were observed during UV modification of polymer film. The most efficient photochemical reactions appeared in sample placed on the rough Al, whereas the smallest effect was observed in polymer on the glass.     

Photoluminescence and optical properties of He ion bombarded ultra-high molecular weight polyethylene

Ion bombardment is a suitable tool to improve the physical and chemical properties of polymer surface. In this study UHMWPE samples were bombarded with 130 keV He ions to the fluences ranging from 1 × 10¹² to 1 × 10¹⁶ cm⁻². The untreated and ion beam modified samples were investigated by photoluminescence, and ultraviolet-visible (UV-vis) spectroscopy. Remarkable decrease in integrated luminescence intensity with increasing ion fluences was observed. The reduction in PL intensity with increase of ion fluence might be attributed to degradation of polymer surface and formation of defects. The effect of ion fluence on the optical properties of the bombarded surfaces was characterized. The values of the optical band gap E_g, and activation energy E_a were determined from the optical absorption. The width of the tail of the localized states in the band gap (E_a) was evaluated using the Urbach edge method. With increasing ion fluences a decrease in both the energy gap and the activation energy were observed. Increase in the numbers of carbon atoms (N) in a formed cluster with increasing the He ion fluence was observed.     

Nitrogen plasma-based ion implantation of poly(tetrafluoroethylene): Effect of the main parameters on the surface properties

The surface of poly(tetrafluoroethylene) (PTFE or Teflon) was treated by nitrogen plasma-based ion implantation. Accelerating voltages between 15 and 30 kV, fluences between 1 × 10¹⁷ and 3 × 10¹⁷ cm⁻² and fluence rates between 3 × 10¹³ and 7 × 10¹³ cm⁻² s⁻¹ were applied. The effects of these main parameters were examined on the evolution of surface chemical composition, mean roughness, abrasive wear, wettability and surface electrical resistance. The aim was to obtain relationships, enabling to control the surface properties examined.The F/C atomic ratio determined by XPS strongly decreased, correlating inversely with voltage. The mean surface roughness characterized by topography measurements, increased, correlating directly with fluence and inversely with voltage. The wear volume obtained by multipass scratch tests did not show clear relationship with the main process parameters, however, it increased upon treatment with the increase of surface roughness and O/C atomic ratio. The water contact angle increased at low voltages and high fluences, due to preferential increase of roughness, and decreased at high voltages and low fluences, owing to intense defluorination and incorporation of N and O. The electrical resistance of the PBII-treated surfaces decreased by several orders of magnitude, showing a significant inverse correlation with fluence. It continued to decrease for samples exposed to air, primarily after treatments performed with low fluences, due to post-treatment type oxidation.     

Characterization of drug-eluting stent (DES) materials with cluster secondary ion mass spectrometry (SIMS)

Secondary ion mass spectrometry (SIMS) employing an SF₅⁺ polyatomic primary ion source was utilized to analyze several materials commonly used in drug-eluting stents (DES). Poly(ethylene-co-vinyl acetate) (PEVA), poly(lactic-co-glycolic acid) (PLGA) and various poly(urethanes) were successfully depth profiled using SF₅⁺ bombardment. The resultant molecular depth profiles obtained from these polymeric films showed very little degradation in molecular signal as a function of increasing SF₅⁺ primary ion dose when experiments were performed at low temperatures (signal was maintained for doses up to ∼5 × 10¹⁵ ions/cm²). Temperature was determined to be an important parameter in both the success of the depth profiles and the mass spectral analysis of the polymers. In addition to the pristine polymer films, paclitaxel (drug released in Taxus™ stent) containing PLGA films were also characterized, where it was confirmed that both drug and polymer signals could be monitored as a function of depth at lower paclitaxel concentrations (10 wt%).     

Luminescence study of SHI irradiated nano semiconductor: Conducting polymer composite

Semiconductor nanoparticle and conducting polymer composite is an interesting class of materials for optoelectronic and photovoltaic device application. We have synthesized a composite of nanocrystalline PbS and conducting polymer MEH-PPV by chemical synthesis and studied the effect of swift heavy ion (SHI) irradiation on the composite material. The irradiation of the composite materials in thin film form is carried out with 120 MeV Si⁺⁹ ion beam at fluences from 5×10¹⁰ to 10¹³ ions/cm². Fluence dependent optical and structural properties have been observed in optical absorption, PL and TEM studies. Reduction of nanoparticle size has been observed after irradiation.     

Effect of flexibility of grafted polymer on the morphology and property of nanosilica/PVC composites

In this study, poly(methyl methacrylate)-grafted-nanosilica (PMMA-g-silica) and a copolymer of styrene (St), n-butyl acrylate (BA) and acrylic acid (AA)-grafted-nanosilica (PSBA-g-silica) hybrid nanoparticles were prepared by using a heterophase polymerization technique in an aqueous system. The grafted polymers made up approximately 50 wt.% of the resulted hybrid nanoparticles which showed a spherical and well-dispersed morphology. The silica hybrid nanoparticles were subsequently used as fillers in a poly(vinyl chloride) (PVC) matrix to fabricate PVC nanocomposite. Morphology study of PVC nanocomposites revealed that both PMMA- and PSBA-grafted-silica had an adhesive interface between the silica and PVC. The tensile strength and elongation to break were found to be improved significantly in comparison with that of untreated nanosilica/PVC composites. Finally our results clearly demonstrated that the properties (e.g. chain flexibility, composition) of the grafted polymer in the hybrid nanoparticles could significantly affect the dispersion behavior of hybrid nanoparticles in PVC matrix, dynamic mechanical thermal properties and mechanical properties of the resulted PVC composites.     

Characterization of polymer thin films obtained by pulsed laser deposition

The development of laser techniques for the deposition of polymer and biomaterial thin films on solid surfaces in a controlled manner has attracted great attention during the last few years. Here we report the deposition of thin polymer films, namely Polyepichlorhydrin by pulsed laser deposition. Polyepichlorhydrin polymer was deposited on flat substrate (i.e. silicon) using an NdYAG laser (266 nm, 5 ns pulse duration and 10 Hz repetition rate).The obtained thin films have been characterized by atomic force microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy and spectroscopic ellipsometry.It was found that for laser fluences up to 1.5 J/cm² the chemical structure of the deposited polyepichlorhydrin polymer thin layers resembles to the native polymer, whilst by increasing the laser fluence above 1.5 J/cm² the polyepichlorohydrin films present deviations from the bulk polymer.Morphological investigations (atomic force microscopy and scanning electron microscopy) reveal continuous polyepichlorhydrin thin films for a relatively narrow range of fluences (1-1.5 J/cm²).The wavelength dependence of the refractive index and extinction coefficient was determined by ellipsometry studies which lead to new insights about the material.The obtained results indicate that pulsed laser deposition method is potentially useful for the fabrication of polymer thin films to be used in applications including electronics, microsensor or bioengineering industries.     

Preferential surface segregation of homopolymer and copolymer blend films

Surface film properties of the homopolymers polystyrene (PS), poly(methyl methacrylate) (PMMA), poly(butyl methacrylate) (PBMA) and the copolymer poly(methyl methacrylate)-co-poly(butyl methacrylate) (PMMA-co-PBMA) and their blends with PS have been examined by atomic force microscopy (AFM) and contact angle measurements. The total and the Lifshitz-van der Waals, acid and base components of the surface free energy together with the work of adhesion and its components, the cohesive energy density and the solubility parameters of the homopolymer, copolymer and blend films were determined. Films of about 3 μm were considered. The results are discussed in terms of surface migration mechanisms based on surface free energy and solubilities of the polymers in the solvent, toluene in this paper. AFM imaging and contact angles revealed surface enrichment at the air polymer interface of PBMA for both the PS/PBMA blend and the copolymer PMMA-co-PBMA, whereas the PS/PMMA and PS/PMMA-co-PBMA blend film surfaces show island-like phase-separated structure of typical size 27.4-86.5 nm in diameter and 6.9-15.6 nm in height for PS/PMMA, while for PS/ PMMA-co-PBMA film surface the typical size is 49.6-153.3 nm in diameter and 1.6-14.2 nm in height.     

Investigation of molecular weight effects of polystyrene in ToF-SIMS using C60 and Au primary ion beams

In secondary ion mass spectrometry, polyatomic primary ion sources are known to enhance yields from many surfaces including polymers. In order to understand the fundamental causes for these increases, the enhancement as a function of material type and molecular weight needs to be delineated. In this article, we report results from a systematic investigation of polymeric films of polystyrene (PS) with varying molecular weights to examine the influence of the primary ion beam on the secondary ion yields in time of flight secondary ion mass spectrometry (ToF-SIMS). The masses of the polymers investigated ranged from 1000 to 20,000 Da, or from about n = 10 to 200 where n indicates the number of polymeric units in a polymer chain. The polymers had a narrow molecular weight range (PDI < 1.07). The multilayer polymeric films (10-30 nm) characterized by AFM were prepared by spin-casting onto silicon substrates and were analyzed using Au⁺ and C₆₀⁺ primary ion beams. The analysis with the two beams provided a useful comparison between atomic and polyatomic primary ion sources. Information gathered from this study provides insight into the role of molecular weight on the observed yield enhancement from polyatomic ion sources.     

Study of a novel porous gel polymer electrolyte based on TPU/PVdF by electrospinning technique

Investigation on a new electrospun gel polymer electrolyte consisting of thermoplastic polyurethane (TPU) and poly(vinylidene fluoride) (PVdF) has been made. Its characteristics were investigated by scanning electron microscopy, FT-IR, Differential Scanning Calorimeter (DSC) analysis. This kind of gel polymer electrolyte had a high ionic conductivity about 3.2 × 10^− 3 S cm^− 1 at room temperature, and exhibited a high electrochemical stability up to 5.0 V versus Li⁺/Li, good mechanical strength and stability to allow safe operation in rechargeable lithium-ion polymer batteries. A Li/GPE/LiFePO₄ cell delivered a high discharge capacity when it was evaluated at 0.1 °C—rate at 25 °C (167.8 mAh g^− 1). And a very stable cycle performance also existed under this low current density.