Modeling of femtosecond ablation of aluminum film with single laser pulses

Detailed investigation of pulsed laser ablation dynamics is performed for aluminum target under action of 100 fs pulses with peak intensity 3.95 × 10¹² W/cm² and wavelength 0.8 μm.Non-equilibrium two-temperature model with hydrodynamic Stephan problem was used for modeling. Explicit tracking of moving interphase boundaries permits exact determination of their velocity and amount of removed and evaporated material. Detailed ablation process is analyzed using the study of temperature, pressure and density evolution in the target. High phase front velocities (melting up to 5 km/s and evaporation up to 350 m/s) are caused by strong overheating of solid and liquid phases.     

激光加热Cu和NaF靶产生的1.2keV区X射线转换效率的测量

介绍了激光加热Cu靶和NaF靶发射的在1.2keV区X射线转换效率的测量方法和实验结果。结果表明,在激光辐照功率密度为1×10¹³—1×10¹⁴W·cm^-2条件下,激光波长为1.06μm或0.53μm时,Cu等离子体发射的1.2KeV区X射线的转换率为NaF等离子体的4—5倍;对此两种等离子体,激光波长为0.53μm的X射线转换效率是波长为1.06μm的2倍左右。 关键词：     

ZnO nanoparticles produced by reactive laser ablation

The paper presents the results of theoretical and experimental researches of the analysis of nanopowder ZnO and ZnO-based structures formation mechanisms by means of pulse laser reactive technology (λ = 1.06 μm, τ = 10⁻⁷ to 10⁻⁵ s). The developed 2D model combines non-stationary heat transfer and fluid motion along with the calculated profile of surface deformation. The characteristics of the dispersive and chemical compositions and structural parameters of the synthesized nanopowder together with the influence of the energy of laser impulse evaporation, its duration and gas pressure in the reaction chamber have been studied using X-ray diffractrometry (XRD), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM). Particle size distribution analysis of ZnO has shown that the majority of them range from 5 to 60 nm in size. The photoluminescence emission spectra of the initial ZnO nanopowder at room temperature have been identified.     

High-efficiency continuous-wave and Q-switched diode-end-pumped multi-wavelength Nd:YAG lasers

We demonstrate high-efficiency diode-end-pumped multi-wavelength Nd:YAG lasers for continuous-wave and Q-switched operation. For the continuous-wave case, the Nd:YAG laser oscillates at 1.06 and 1.3 μm simultaneously; the maximum output power of 2.0 W (M² = 1.3) and 3.6 W (M² = 1.8) have been achieved at the incident pump power of 20.3 W, with the respective average slope efficiencies of 12.0% and 21.4%, for the lines of 1.06 and 1.3 μm, respectively. For the Q-switched operation, we achieve the average output power of 1.3 W (M² = 2.7) at 1.06 μm and 2.0 W (M² = 3.0) at 1.3 μm with the corresponding peak power of 10.2 and 4.2 kW under an incident pump power of 20.3 W.     

Pulsed infrared radiation transmission through chalcogenide glass fibers

Two different kinds of chalcogenide glass IR fibers were evaluated relative to transmission of pulsed IR radiation produced by several laser sources in the wavelength range from 1 to 10 μm. Fibers composed either from As-Se-Te or from As₂S₃ glass, of 250, 500, 750 and 1000 μm and 250, 750 and 1000 μm core diameters were studied, respectively. Attenuation measurements were obtained as a function of the laser energy input and as a function of curvature, wherever this was possible. The output beam quality was also studied using a beam profiler. The lasers used were a Q-switched Nd:YAG laser, emitting at 1.06 μm, a free-running or Q-switched Er:YAG laser emitting at 2.94 μm and a tunable pulsed CO₂ laser emitting in the range of 9.3-10.6 μm. The fibers exhibited better behavior when tested with the Er:YAG laser and they were found fragile in pulsed radiation from the Nd:YAG and the CO₂ laser. The output beam profiles generally showed a central multi-spiking energy distribution.     

Enhanced blue-green-red up-conversion and 1.3-μm emission of Pr/Yb-codoped oxyhalide tellurite glasses with PbCl2 doping

We report on the blue-green-red up-conversion spectroscopic properties of Pr³⁺/Yb³⁺-codoped oxyhalide tellurite glasses upon excitation of a conventional 980 nm laser diode (LD). Significant enhancement of the blue-green-red up-conversion emission intensity has been observed with increasing PbCl₂ doping. The up-conversion intensity has a quadratic dependence on incident pump laser power, indicating a two-photon process. The population of the Pr³⁺ upper ³P₀ emitting level was accomplished through a combination of a ground state absorption, energy transfer and excitated state absorption. 1.3-μm emission in the second telecom window originated from Pr³⁺:¹G₄→³H₅ transition has also been investigated upon excitation at 980 nm LD. The measured peak wavelength and full width at half-maximum of the fluorescent are 1335 nm and ∼100 nm, respectively. An enhanced 1.3μm emission with increasing PbCl₂ doping has also been observed. Codoping of Yb³⁺ significantly enhance both the blue-green-red up-conversion emission and 1.3-μm emission intensity by way of a nonradiative Yb³⁺:²F₅→Pr³⁺:¹G₄ energy transfer.     

Laser desorption studies using laser-induced fluorescence of large aromatic molecules

Pulsed laser desorption of non-volatile organic dye molecules paraterphenyl and tetra-t-butyl-p-quinquephenyl (QUI) was studied using gas phase ultraviolet laser induced fluorescence, following heating of a steel substrate by a pulsed 1.06-μm Nd:YAG laser. The fluorescence signal intensity is linear in concentration up to at least 30 monolayers and shows infrared power threshold behavior, as expected for evaporation, at ∼0.2 J/cm². Similar signal levels were also observed in air, with 532-nm heating, and using other metallic or dark black surfaces.     

Surface temperature evolution in pulsed laser action of millisecond range

An originally developed multi-wavelength pyrometer (12 wavelengths in the range 1.001-1.573 μm, 50 μs acquisition time for each photodiode, 800 μm spatial resolution, 900-3500 °C brightness temperature range) is used to measure brightness temperature under the pulsed action of Nd:YAG laser (HAAS-HL62P) on stainless steel (INOX 304L) substrates. Specially developed “notch” filters (10⁻⁶ transparency at 1.06 μm wavelength) are applied to avoid the influence of laser radiation on temperature measurements. The true temperature is restored on the basis of method of multi-colour pyrometry. The accuracy of brightness temperature measurements is examined by comparing the temperature evolution for pulses with different durations but with the same value of energy density flux.The influence of the following parameters is studied keeping the remaining ones constant: pulse duration (6-20 ms, rectangular pulse shape), energy per pulse (10-33 J, rectangular pulse shape), pulse shape (three types of triangulars and one rectangular). Finally the evolution of surface temperature for pulses with more complex shapes but with the same pulse duration and energy per pulse is compared.     

Generation of tunable infrared radiation in rubidium titanyl phosphate crystal for the optical measurement of number density, absorption cross-section of methane gas

Tunable near-infrared radiation has been generated in a rubidium titany1 phosphate (RTP) crystal by employing non-collinear difference-frequency mixing (DFM) technique. The input radiation sources are Nd:YAG laser radiation and its second harmonic pumped dye laser radiation. For the generation of 2.0 radiation, the maximum value of the conversion efficiency (quantum) obtained in the process is 49% from the dye (0.6945 μm) to the infrared (2.0 μm) radiation in the 7.9-mm-long crystal. The generated tunable mid-infrared radiation has been used to measure the number density, absorption cross-section and minimum detectable concentration of methane gas in its 2ν₃ band in a multi-pass cell at 30.075 Torr pressure. The number density and column density of the methane molecules are found to be 1.068×10¹⁸ cm⁻³ and 3.02×10²¹ cm⁻², respectively, whereas the minimum still-detectable concentration at 1.658 μm wavelength is estimated to be 4.523×10¹⁷/cm³.     

All-optical Bose-Einstein condensation in a 1.06 μm dipole trap

We report the all-optical production of a ⁸⁷Rb Bose-Einstein condensate (BEC) in a simple 1.06 μm dipole trap experiment. We load a single beam dipole trap directly from a magneto-optic trap (MOT). After evaporation in the single beam, a second crossed beam is used for compression. The intensity in both beams is then reduced for evaporation to BEC. We obtain a BEC with 3.5 × 10⁴ atoms after 3 s of total evaporation time. We also give a detailed account of the thermal distribution in cross beam traps. This account highlights the possible difficulties in using shorter wavelength lasers to condense all optically.     

High power single-shot laser ablation of silicon with nanosecond 355 nm

We report on high intensity single-shot laser ablation of monocrystalline silicon with a nanosecond Nd:YAG at 355 nm. It is shown that for incident laser intensities exceeding ∼11.5 GW/cm² on the silicon surface, unusually high etch depths can be achieved reaching values up to 60 μm. The results support previous observations of dramatic increase in etch rates in single-shot laser ablation at 266 nm. A laser-induced explosive boiling mechanism together with secondary plasma heating is believed to be associated with this effect.     

Direct observation of phase transitions by time-resolved pyro/reflectometry of KrF laser-irradiated metal oxides and metals

New experimental results are obtained by coupling both time-resolved reflectivity and rapid infrared pyrometry under a hemispherical reactor. The heating source KrF laser beam (28 ns, 248 nm) is homogenized and as for probing, a CW He-Ne laser beam (10 mW, 633 nm) is used.Using both methods infrared pyrometry with an IR detector cooled with liquid nitrogen and sensitive in the spectral range 1-12 μm, and time-resolved reflectivity with a rapid photodiode, we were able to study complex thermodynamic transitions with nanosecond time resolution. Three different materials are studied by varying the KrF fluence (energy/surface) from 100 to 2000 mJ/cm²: thin films melting (Au/Ni), the threshold of plasma formation (Ti), and complex liquid phase segregation under semi-conductor state (ZnO). The formation of a liquid Zn film induced by temperature gradient is well evidenced by our signals. Also melting of thin films irradiated by low laser fluences (less than 500 mJ/cm²) translates the typical thermodynamic behavior. Finally, wide fluence dynamic (400-2000 mJ/cm²) is analyzed in the case of Ti surface, and results show two distinguished regimes: first one bellow 1000 mJ/cm² corresponding to the early stage plasma initiation, and second one over 1000 mJ/cm² to the dynamics of plasma expansion.     

Hot embossing of PTFE: Towards superhydrophobic surfaces

Three types of reusable stamps with features in the form of 2D arrays of pits having lateral dimensions in the range of 2-80 μm and heights of 1.5-15 μm were successfully employed for the hot embossing of PTFE at temperatures up to 50 °C above the glass transition temperature of PTFE amorphous phase. Due to the softening of PTFE at the temperatures used in this study, we were able to decrease imprint pressure significantly when comparing with the imprint conditions reported by other authors. Impact of the imprint temperature, pressure and time on the fidelity of pattern transfer as well as on water repellency was tested. The best results of embossing were achieved by applying pressure of 10 kg/cm² for 2 min at 170 °C. In this case, flattening of a natural PTFE roughness and pretty accurate deep replicas of the stamp patterns were observable on the whole imprinted area. Improvement in water repellency was largest for the samples imprinted by Ni stamp patterned with a 2D array of 2 μm square pits spaced by the same dimension and having a depth of 1.5 μm. Cassie-Baxter wetting regime was observed for the deepest imprints with water contact angles up to the superhydrophobic limit.     

Water mist attenuates guided laser based on Monte Carlo method

The round-trip attenuating process of lasers used for guiding in artificial water mists is studied with the Monte-Carlo method. A new way for confirming the scattering directions of photons is established based on calculating Mie cumulative probability distribution function of the polydisperse mist and user defined function fitting by Matlab. Two Monte-Carlo methods for photons tracking are mentioned and their efficiencies are discussed and balanced in this paper. A conclusion is come to that the Wight method is evidently more efficiency than the Event method, and the former is adopted in this paper. The radiuses of frequently-used water mists are usually in the range of 10¹–10² μm which are found to be suited to attenuate the 10.6 μm laser and can be used for laser stealth. But the effect is worse for 1.06 μm laser.     

Surface modifications of crystalline silicon created by high intensity 1064 nm picosecond Nd:YAG laser pulses

A study of silicon modification induced by a high intensity picosecond Nd:YAG laser, emitting at 1064 nm, is presented. It is shown that laser intensities in the range of 5 × 10¹⁰-0.7 × 10¹² W cm⁻² drastically modified the silicon surface. The main modifications and effects can be considered as the appearance of a crater, hydrodynamic/deposition features, plasma, etc. The highest intensity of ∼0.7 × 10¹² W cm⁻² leads to the burning through a 500 μm thick sample. At these intensities, the surface morphology exhibits the transpiring of the explosive boiling/phase explosion (EB) in the interaction area. The picosecond Nd:YAG laser-silicon interaction was typically accompanied by massive ejection of target material in the surrounding environment. The threshold for the explosive boiling/phase explosion (TEB) was estimated to be in the interval 1.0 × 10¹⁰ W cm⁻² < TEB ≤ 3.8 × 10¹⁰ W cm⁻².     

Infrared and far-infrared spectroscopy of CH3OH: TeraHertz laser lines and assignments

We use a ¹³CO₂ laser as optical pumping source to search for new THz laser lines generated from ¹³CH₃OH. Nineteen new THz laser lines (also identified as far-infrared, FIR) ranging from 42.3 μm (7.1 THz) to 717.7 μm (0.42 THz) are reported. They are characterized in wavelength, offset, relative polarization, relative intensity, and optimum working pressure. We have assigned eight laser lines to specific rotational energy levels in the excited state associated with the C-O stretching mode.     

Widely phase-matched tunable difference-frequency generation in periodically poled LiNbO3 crystal

We report on the development of a laser source in the mid-infrared spectral region based on difference-frequency generation (DFG) in a periodically poled LiNbO₃ (PPLN) crystal. Continuously tunable coherent radiation from 2.75 to 4.78 μm was produced by optical parametric interaction between a diode-pumped monolithic continuous-wave (CW) Nd:YAG laser operating at 1.064 μm and a CW Ti:Sapphire laser tunable from 767 to 871 nm. Temperature-dependent quasi-phase-matched DFG wavelength acceptance bandwidth was studied and characterized. An empiric formula is given to estimate the phase-matched wavelength acceptance bandwidth as a function of the crystal temperature at Λ = 22.5 μm. A large frequency scan of 128 cm⁻¹ (about 78 cm⁻¹ above 1 μW) near 4.2 μm was achieved. The whole absorption spectrum of the P and R branches of the ν₃ band of atmospheric carbon dioxide has been recorded with a single phase-matched frequency scan.     

Matrix assisted pulsed laser evaporation of cinnamate-pullulan and tosylate-pullulan polysaccharide derivative thin films for pharmaceutical applications

We have demonstrated the successful thin film growth of two pullulan derivatives (cinnamate-pullulan and tosylate-pullulan) using matrix assisted pulsed laser evaporation (MAPLE). Our MAPLE system consisted of a KrF* laser, a vacuum chamber, and a rotating target holder cooled with liquid nitrogen. Fused silica and silicon (1 1 1) wafers were used as substrates. The MAPLE-deposited thin films were characterized by transmission spectrometry, profilometry, atomic force microscopy (AFM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy. The deposited layers ranged from 250 nm to 16.5 μm in thickness, depending on the laser fluence (0.065-0.5 J cm⁻²) and number of pulses applied for the deposition of one structure (1500-13,300). Our results confirmed that MAPLE was well-suited for the transfer of cinnamate-pullulan and tosylate-pullulan.     

Q-switched Nd lasers pumped directly into the F3/2 emitting level

The influence of the direct pumping into the ⁴F_3/2 emitting level on the output characteristics of continuous-wave (CW) pumped, passively or actively (acoustooptic, AO) Q-switched Nd lasers is discussed. In case of passive Q-switching by Cr⁴⁺:YAG saturable absorber (SA) crystal, the change of pumping wavelength from 0.81 μm into the highly-absorbing ⁴F_5/2 level to 0.88 μm into the ⁴F_3/2 level of Nd does not modify the energy of the Q-switch pulse, but increases the pulse repetition rate and the laser average power for the same absorbed pump power. This is demonstrated with 0.81 and 0.88 μm CW laser diode-pumped Nd:YAG and Nd-vanadate lasers with average output power in the watt-level range at 1.06 μm. The effect is explained by the control of passive Q-switching by the intracavity photon flux that is influenced by the pump wavelength and by the initial transmission of the SA crystal. On the other hand, it is discussed and experimentally proved that due to the possibility to control externally the frequency of switching, in case of the AO Q-switched Nd laser the change of the pump wavelength from 0.81 to 0.88 μm increases the pulse energy for a fixed frequency, leading to a corresponding increase of the average laser power.     

3D periodic structures grown on silicon by radiation of a pulsed Nd:YAG laser and their field emission properties

Periodic three-dimensional structures were successfully grown on single crystal Si wafers either bare or Au-covered under their exposure to a pulsed radiation of a Nd:YAG laser in vacuum. The structures protrude above the initial wafer surface for 10 μm while their spatial period is about 70 μm. The coupling of the laser radiation to Si surface is related to the thermal non-linear absorption of the near band gap radiation. The structures exhibit an efficient field emission with an average emission current of 5 mA/cm² and is sensitive to the post-treatment of samples. The drawbacks of the emission current densities are discussed.