Removal of graffiti from the mortar by using Q-switched Nd:YAG laser

This paper presents part of the larger study on microstructural features of mortars and it's effects on laser cleaning process. It focuses on the influence of surface roughness, porosity and moisture content of mortars on the removal of graffiti by Nd:YAG laser. The properties of this laser are as follows: wavelength (λ) 1.06 μm, energy: 500 mJ per pulse, pulse duration: 10 ns. The investigation shows that the variation of laser fluence with the number of pulses required for the laser cleaning can be divided into two zones, namely effective zone and ineffective zone. There is a linear relationship observed between number of pulses required for laser cleaning and the laser fluence in the effective zone, while the number of pulses required for the laser cleaning is almost constant even though the laser fluence increases in the ineffective zone. Moreover, surface roughness, porosity and moisture content of mortar samples have influence on the laser cleaning process. The effect of these parameters become however negligible at the high level of laser fluence. The number of pulses required for the laser cleaning is low for smooth surface or less porous mortar. Furthermore, the wetness of the samples facilitates the cleaning process.     

Application of the laser ablation for conservation of historical paper documents

Laser ablation was applied for surface cleaning and spectroscopic diagnostics of historical paper documents and model samples in the framework of the conservation projects. During cleaning the spectra of ablation products were recorded by means of the LIBS technique which allowed for nearly non-destructive identification of surface layers such as contaminants, substrate and pigments. For consecutive laser pulses a strong decrease of band intensities of the emission lines of Ca, Na, K, Al and Fe ascribed to contaminants were observed. The effect was used for monitoring of the cleaning progress of stained paper. For surface cleaning and spectra excitation the Q-switched Nd:YAG laser of 6 ns pulsewidth operating at wavelengths of 266, 355, 532, and 1064 nm and of fluence selected from the range 0.3-0.9 J/cm² was applied. The ablation parameters were optimized in agreement with the literature and the results were confirmed by surface studies and testing of the mechanical and chemical properties, and also by the response to the ageing process of the paper substrate. In case of the model paper irradiated in the UV range at 266 and 355 nm a visual inspection revealed local damages of the cellulose fibers accompanied by a decrease of the mechanical strength of the substrate. The effect was more pronounced after artificial ageing. The best results were obtained for samples irradiated at 532 nm and at laser fluence below the damage threshold of 0.6 J/cm², which is in agreement with literature.     

Fixation of bioactive calcium alkali phosphate on Ti6Al4V implant material with femtosecond laser pulses

Bone implants made of metal, often titanium or the titanium alloy Ti6Al4V, need to be surface treated to become bioactive. This enables the formation of a firm and durable connection of the prosthesis with the living bone. We present a new method to uniformly cover Ti6Al4V with a thin layer of ceramics that imitates bone material. These calcium alkali phosphates, called GB14 and Ca10, are applied to the metal by dip coating of metal plates into an aqueous slurry containing the fine ceramic powder. The dried samples are illuminated with the 790 nm radiation of a pulsed femtosecond laser. If the laser fluence is set to a value just below the ablation threshold of the ceramic (ca. 0.4 J/cm²) the 30 fs laser pulses penetrate the partly transparent ceramic layer of 20-40 μm thickness. The remaining laser fluence at the ceramic-metal interface is still high enough to generate a thin metal melt layer leading to the ceramic fixation on the metal. The laser processing step is only possible because Ti6Al4V has a lower ablation threshold (between 0.1 and 0.15 J/cm²) than the ceramic material. After laser treatment in a fluence range between 0.1 and 0.4 J/cm², only the particles in contact with the metal withstand a post-laser treatment (ultrasonic cleaning). The non-irradiated rest of the layer is washed off. In this work, we present results of a successful ceramic fixation extending over larger areas. This is fundamental for future applications of arbitrarily shaped implants.     

Laser cleaning of 19th century Congo rattan mats

There is a growing interest by art conservators for laser cleaning of organic materials, such as wooden artworks, paper and textiles, since traditional cleaning with solvents can be a source of further decay and mechanical cleaning may be too abrasive for sensitive fibers. In this work we present a successful laser cleaning approach for 19th century rattan mats from the Brooklyn Museum collection of African Art, now part of the study collection at the Conservation Center in New York. Tests were carried out using the fundamental (1064 nm) and second harmonic (532 nm) wavelength of a Q-switched Nd:YAG laser to measure threshold values both for surface damage and color changes for different types of rattan samples. The irradiated substrates were investigated by optical microscopy, scanning electron microscopy and by UV-vis spectroscopy in order to determine the efficiency of laser cleaning and to assess possible deterioration effects that may have occurred as a result of laser irradiation. The study showed that by using the laser emission at 532 nm, a wavelength for which photon energy is below the bond dissociation level of the main cellulosic compounds and the water absorption is negligible, it is possible to select a range of laser fluences to remove the black dust layer without damaging the rattan material.     

Target-plane deposition of diamond-like carbon in pulsed laser ablation of graphite

In pulsed Nd:YAG laser ablation of highly oriented pyrolytic graphite (HOPG) at 10⁻⁶ Torr, diamond-like carbon (DLC) are deposited at laser wavelengths of 1064, 532, and 355 nm on substrates placed in the target-plane. These target-plane samples are found to contain varying sp³ content and composed of nanostructures of 40-200 nm in size depending on the laser wavelength and laser fluence. The material and origin of sp³ in the target-plane samples is closely correlated to that in the laser-modified HOPG surface layer, and hardly from the backward deposition of ablated carbon plume. The surface morphology of the target-plane samples shows the columnar growth and with a tendency for agglomeration between nanograins, in particular for long laser wavelength at 1064 nm. It is also proposed that DLC formation mechanism at the laser-ablated HOPG is possibly via the laser-induced subsurface melting and resolidification.     

Investigation on upconversion photoluminescence of Bi3TiNbO9:Er:Yb thin films

Bi₃TiNbO₉:Er³⁺:Yb³⁺ (BTNEY) thin films were fabricated on fused silica by pulsed laser deposition. It was demonstrated that different laser fluence and substrate temperature during growth of BTNEY upconversion photoluminescence (UC-PL) samples control the film’s grain size and hence influences the UC-PL properties. The average grain size of BTNEY thin films deposited on fused silica substrates with laser fluence 4, 5, 6, and 7 J/cm² are 30.8, 35.9, 40.6, and 43.4 nm, respectively. The 525 nm emission intensities increase with the deposition laser fluence and the emission intensities of BTNEY thin film deposited under 700 and 600 °C are almost 24 and 4 times, respectively, as strong as those of samples under 500 °C. The grain size of BTNEY thin film increases with the increasing temperature. UC-PL of BTNEY films is enhanced by increasing grain size of the films.     

Analyses of surface coloration on TiO2 film irradiated with excimer laser

TiO₂ film of around 850 nm in thickness was deposited on a soda-lime glass by PVD sputtering and irradiated using one pulse of krypton-fluorine (KrF) excimer laser (wavelength of 248 nm and pulse duration of 25 ns) with varying fluence. The color of the irradiated area became darker with increasing laser fluence. Irradiated surfaces were characterized using optical microscopy, scanning electron microscopy, Raman spectroscopy and atomic force microscopy. Surface undergoes thermal annealing at low laser fluence of 400 and 590 mJ/cm². Microcracks at medium laser fluence of 1000 mJ/cm² are attributed to surface melting and solidification. Hydrodynamic ablation is proposed to explain the formation of micropores and networks at higher laser fluence of 1100 and 1200 mJ/cm². The darkening effect is explained in terms of trapping of light in the surface defects formed rather than anatase to rutile phase transformation as reported by others. Controlled darkening of TiO₂ film might be used for adjustable filters.     

Microstructuring of fused silica by laser-induced backside wet etching using picosecond laser pulses

The laser-induced backside wet etching (LIBWE) is an advanced laser processing method used for structuring transparent materials. LIBWE with nanosecond laser pulses has been successfully demonstrated for various materials, e.g. oxides (fused silica, sapphire) or fluorides (CaF₂, MgF₂), and applied for the fabrication of microstructures. In the present study, LIBWE of fused silica with mode-locked picosecond (t_p = 10 ps) lasers at UV wavelengths (λ₁ = 355 nm and λ₂ = 266 nm) using a (pyrene) toluene solution was demonstrated for the first time. The influence of the experimental parameters, such as laser fluence, pulse number, and absorbing liquid, on the etch rate and the resulting surface morphology were investigated. The etch rate grew linearly with the laser fluence in the low and in the high fluence range with different slopes. Incubation at low pulse numbers as well as a nearly constant etch rate after a specific pulse number for example were observed. Additionally, the etch rate depended on the absorbing liquid used; whereas the higher absorption of the admixture of pyrene in the used toluene enhances the etch rate and decreases the threshold fluence. With a λ₁ = 266 nm laser set-up, an exceptionally smooth surface in the etch pits was achieved. For both wavelengths (λ₁ = 266 nm and λ₂ = 355 nm), LIPSS (laser-induced periodic surface structures) formation was observed, especially at laser fluences near the thresholds of 170 and 120 mJ/cm², respectively.     

Small size TiO2 nanoparticles prepared by laser ablation in water

Titanium dioxide nanoparticles in distilled H₂O solvent were prepared by laser ablation. The experiments were performed irradiating a Ti target with a second harmonic (532 nm) output of a Nd:YAG laser varying the operative fluence between 1 and 10 J cm⁻² and for an ablation time ranging from 10 to 30 min. Electron microscopy measurements have evidenced the predominant presence of nanoparticles with diameter smaller than 10 nm together with agglomerations of 100-200 nm whose content increases with the laser fluence. At low laser fluence the particles’ size distribution shows that more than 85% of the nanoparticles have a size smaller than 5 nm while at mid and high fluences the presence of 5-7 nm nanoparticles is predominant. XPS analysis has revealed the presence of different titanium suboxide phases with the prevalence of Ti-O bonds from TiO₂ species. The optical bandgap values, determined by UV-vis absorption measurements, are compatible with the anatase phase.     

Enhanced cleaning of photoresist film on a transparent substrate by backward irradiation of a Nd:YAG laser

Laser cleaning of a photoresist (PR) on a glass substrate using ns-pulsed Nd:YAG laser was studied. The direction of the substrate facing the laser beam was varied as a main parameter as well as the power of the laser beam. The backward irradiation (BWI) of the third harmonic beam (355 nm) completely removed 1.2 μm thick PR layer with three pulses at 1.5 J/cm² leaving no residues behind; while the forward irradiation (FWI) at the same condition just partially cleaned it. To investigate the difference of removal mechanisms between irradiation directions, the size distributions of particulates generated during laser cleaning were observed using an optical particle counter. The concentration of micron-sized particulates increased with increasing laser fluence up to 1 J/cm² for FWI and 0.5 J/cm² for BWI and then decreased at higher fluences because the target was a very thin film. The concentration of larger particulates for BWI was much higher than that for FWI implying the difference in removal mechanisms. In consideration of the size characteristics of the particulates and the temperature profiles of the PR layer, the most probable distinct mechanism for the BWI would be a blasting due to high temperature at the PR/glass interface. The particulate number concentration decreased rapidly after the completion of cleaning, suggesting that the measurement of the particulate concentration could detect the progress of the cleaning. Our results demonstrated that the backward irradiation will be useful for the laser cleaning of film-type contaminants on an optically transparent substrate.     

Characterization of Ag and Au nanoparticles created by nanosecond pulsed laser ablation in double distilled water

Pulsed laser ablation of Ag and Au targets, immersed in double-distilled water is used to synthesize metallic nanoparticles (NPs). The targets are irradiated for 20 min by laser pulses at different wavelengths—the fundamental and the second harmonic (SHG) (λ = 1064 and 532 nm, respectively) of a Nd:YAG laser system. The ablation process is performed at a repetition rate of 10 Hz and with pulse duration of 15 ns. Two boundary values of the laser fluence for each wavelength under the experimental conditions chosen were used—it varied from several J/cm² to tens of J/cm². Only as-prepared samples were measured not later than two hours after fabrication. The NPs shape and size distribution were evaluated from transmission electron microscopy (TEM) images. The suspensions obtained were investigated by optical transmission spectroscopy in the near UV and in the visible region in order to get information about these parameters. Spherical shape of the NPs at the low laser fluence and appearance of aggregation and building of nanowires at the SHG and high laser fluence was seen. Dependence of the mean particle size at the SHG on the laser fluence was established. Comments on the results obtained have been also presented.     

Laser fluence, repetition rate and pulse duration effects on paint ablation

The efficiency (mm³/(J pulse)) of laser ablation of paint was investigated with nanosecond pulsed Nd:YAG lasers (λ = 532 nm) as a function of the following laser beam parameters: pulse repetition rate (1-10,000 Hz), laser fluence (0.1-5 J/cm²) and pulse duration (5 ns and 100 ns). In our study, the best ablation efficiency (η ≅ 0.3 mm³/J) was obtained with the highest repetition rate (10 kHz) at the fluence F = 1.5 J/cm². This ablation efficiency can be associated with heat accumulation at high repetition rate, which leads to the ablation threshold decrease. Despite the low thermal diffusivity and the low optical absorption of the paint (thermal confinement regime), the ablation threshold fluence was found to depend on the pulse duration. At high laser fluence, the ablation efficiency was lower for 5 ns pulse duration than for the one of 100 ns. This difference in efficiency is probably due to a high absorption of the laser beam by the ejected matter or the plasma at high laser intensity. Accumulation of particles at high repetition rate laser ablation and surface shielding was studied by high speed imaging.     

Polymer self-assembled nano-structures and surface relief gratings induced with laser at 157 nm

Surface relief gratings (SRG) and self-organized nano-structures induced by laser light at 157 nm on the fluoropolymer poly(2,2,2-trifluoroethyl methacrylate) (PTFEMA), films were obtained under well-controlled light exposure conditions. Regular and semi-regular spaced self-organized grating-like structures were created on polymeric films for ∼7.5-100 mJ/cm² laser energy fluence. For lower laser fluence, the surface morphology of light exposed/non-exposed areas exhibited irregular-like structure morphologies, while polymer surface irradiation with energy fluence higher than 150 mJ/cm² causes progressively fading out of the regular patterns. Under the specific experimental conditions, the SRG and self-organization patterning have their origin in the development of a surface thermal instability (Rayleigh's instability), which is resolved itself into regular patterns on the surface of the fluoropolymer film. The thermal instability is due to the explosive polymer surface photo-dissociation at 157 nm and the build up of longitudinal and periodic surface stress, which eventually create the SRG and the self-assembled structures on the polymer.     

Synthesis of nanosized particles during laser ablation of gold in water

In this paper we report the formation of gold nanoparticles during laser ablation of gold target in water in the absence of any additives. The experiments were carried out by using the radiation of the pulsed Nd:YAG laser, operating at the second (532 nm, 10 ns, 10 Hz), or the fourth harmonic (266 nm) wavelengths. The properties of the nanoparticles were found to be susceptible to the additional 532 and 266 nm laser irradiation. It has been established that both the mean size of the nanoparticles and their stability could be varied by proper selection of the parameters of laser ablation and postirradiation such as laser fluence and wavelength combinations.     

Laser cleaning of contamination on sandstone surfaces in Yungang Grottoes

Laser cleaning is firstly used to remove the contaminations on the sandstone surfaces in Yungang Grottoes. A Q-switched Nd:YAG laser operated at 1064 nm with a pulse width of 10 ns is used to perform the experiments. Before experiments in Yungang Grottoes, the laboratory experiments on sandstone samples obtained from Shanxi province have been conducted. The laser induced damage thresholds of the uncontaminated sandstones and the laser cleaning thresholds of ink contaminated sandstones have been obtained in the laboratory. The difference between the cleaning effects of dry laser cleaning and steam laser cleaning has been compared. On the basis of the laboratory experimental data, the experiments in Yungang Grottoes have been conducted and the results indicate that laser cleaning is safe and effective for removal of graffiti ink and black smudges of smoke.     

Study on metal microparticle content of the material transferred with Absorbing Film Assisted Laser Induced Forward Transfer when using silver absorbing layer

Absorbing Film Assisted Laser Induced Forward Transfer (AFA-LIFT) is a modified LIFT method where a high absorption coefficient thin film coating of a transparent substrate is used to transform the laser energy into kinetic in order to transfer the “target” material spread on it. This method can be used for the transfer of biomaterials and living cells, which could be damaged by direct irradiation of the laser beam. In previous experiments, ∼50-100 nm thick metal films have been used as absorbing layer. The transferred material can also contain metal microparticles originating from the absorbing thin film and acting as non-desired impurities in some cases. The aim of our work was to study how the properties (number, size and covered area) of metal particles transferred during the AFA-LIFT process depend on film thickness and the applied fluence. Silver thin films with different thickness (50-400 nm) were used as absorbing layers and real experimental conditions were modeled by a 100 μm thick water layer. The particles transferred without the use of water layer were also studied. The threshold laser fluence for the complete removal of the absorber from the irradiated area was found to strongly increase with increasing film thickness. The deposited micrometer and submicrometer particles were observed with optical microscope and atomic force microscope. Their size ranged from 100 nm to 20 μm and depended on the laser fluence. The increase in fluence resulted in an increasing number of particles of smaller average size.     

Enhanced near field mediated nanohole fabrication on silicon substrate by femtosecond laser pulse

Investigation of the process of nanohole formation on silicon surface mediated with near electromagnetic field enhancement in vicinity of gold particles is described. Gold nanospheres with diameters of 40, 80 and 200 nm are used. Irradiation of the samples with laser pulse at fluences below the ablation threshold for native Si surface, results in a nanosized surface modification. The nanostructure formation is investigated for the fundamental (λ = 800 nm, 100 fs) and the second harmonic (λ = 400 nm, 250 fs) of the laser radiation generated by ultrashort Ti:sapphire laser system. The near electric field distribution is analyzed by an Finite Difference Time Domain (FDTD) simulation code. The properties of the produced morphological changes on the Si surface are found to depend strongly on the polarization and the wavelength of the laser irradiation. When the laser pulse is linearly polarized the produced nanohole shape is elongated in the E-direction of the polarization. The shape of the hole becomes symmetrical when the laser radiation is circularly polarized. The size of the ablated holes depends on the size of the gold particles, as the smallest holes are produced with the smallest particles. The variation of the laser fluence and the particle size gives possibility of fabricating structures with lateral dimensions ranging from 200 nm to below 40 nm. Explanation of the obtained results is given on the basis simulations of the near field properties using FDTD model and Mie's theory.     

Morphology and composition on Al surface irradiated by femtosecond laser pulses

We study the surface chemicals and structures of aluminum plates irradiated by scanning femtosecond laser pulses in air for a wide range of laser fluence from 0.38 to 33.6 J/cm². X-ray photoelectron spectroscopy and X-ray diffraction analyses indicate clearly that crystalline anorthic Al(OH)₃ is formed under femtosecond laser pulse irradiation. Besides aluminum hydroxide, crystalline Al₂O₃ is also found in the samples irradiated at high laser fluence. Field emission scanning electron microscopy demonstrates that the surfaces of the samples irradiated with low laser fluence are colloidal-like and that nanoparticles with a few nanometers in size are embedded in glue-like substances. For high laser fluence irradiated samples, the surfaces are highly porous and covered by nanoparticles with uniform size of less than 20 nm.     

Femtosecond laser micromilling of Si wafers

Femtosecond laser micromilling of silicon is investigated using a regeneratively amplified 775 nm Ti:Sapphire laser with a pulse duration of 150 fs operating at 1 kHz repetition rate. The morphological observation and topological analysis of craters fabricated by single-shot laser irradiation indicated that the material removal is thermal in nature and there are two distinct ablation regimes of low fluence and higher fluence with logarithmical relations between the ablation depth and the laser fluence. Crater patterns were categorized into four characteristic groups and their formation mechanisms were investigated. Femtosecond laser micromilling of pockets in silicon was performed. The effect of process parameters such as pulse energy, translation speed, and the number of passes on the material removal rate and the formation of cone-shaped microstructures were investigated. The results indicate that the microstructuring mechanism has a strong dependence on the polarization, the number of passes and laser fluence. The optimal laser fluence range for Si micromilling was found to be 2-8 J/cm² and the milling efficiency attains its maximum between 10 and 20 J/cm².     

Periodic surface structures on crystalline silicon created by 532 nm picosecond Nd:YAG laser pulses

Creation of laser-induced morphology features, particularly laser-induced periodic surface structures (LIPSS), by a 532 nm picosecond Nd:YAG laser on crystalline silicon is reported. The LIPSS, often termed ripples, were produced at average laser irradiation fluences of 0.7, 1.6, and 7.9 J cm⁻². Two types of ripples were registered: micro-ripples (at micrometer scale) in the form of straight parallel lines extending over the entire irradiated spot, and nano-ripples (at nanometer scale), apparently concentric, registered only at the rim of the spot, with the periodicity dependent on laser fluence. There are indications that the parallel ripples are a consequence of the partial periodicity contained in the diffraction modulated laser beam, and the nano-ripples are very likely frozen capillary waves. The damage threshold fluence was estimated at 0.6 J cm⁻².