Synergistic film-forming effect of oligo(ethylene oxide)-functionalized trimethoxysilane and propylene carbonate electrolytes on graphite anode

Oligo(ethylene oxide)-functionalized trialkoxysilanes can be used as novel electrolytes for high-voltage cathode, such as LiCoO₂ (4.35 V) and Li_1.2Ni_0.2Mn_0.6O₂ (4.6 V); however, they are not well compatible with graphite anode. In this study, a synergistic solid electrolyte interphase (SEI) film-forming effect between [3-[2-(2-methoxyethoxy)ethoxy]propyl]-trimethoxysilane (TMSM2) and propylene carbonate (PC) on graphite electrode was investigated. Excellent SEI film-forming capability and cycling performance was observed in graphite/Li cells using the electrolyte of 1 M LiPF₆ in the binary solvent of TMSM2 and PC, with the PC content in the range of 10–30 vol.%. Meanwhile, the graphite/Li cells delivered higher specific capacity and better capacity retention in the electrolyte of 1 M LiPF₆ in TMSM2 and PC (TMSM2:PC = 9:1, by vol.), compared with those in the electrolyte of 1 M LiPF₆ in TMSM2 and EC (TMSM2:EC = 9:1, by vol.). The synergistic SEI film-forming properties of TMSM2 and PC on the surface of graphite anode was characterized by electrolyte solution structure analysis through Raman spectroscopy and surface analysis detected by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FT-IR) analysis.     

Hydroxyl terminated Poly(dimethylsiloxane) as an electrolyte additive to enhance the cycle performance of lithium-ion batteries

Hydroxyl terminated poly(dimethylsiloxane) (PDMS-HT) is used as an electrolyte additive in electrolyte systems containing 1 M LiPF₆ in EC:DMC (ratios 1:9; 3:7; 4:6 and 1:1 v/v) to enhance the cycle performance of lithium-ion batteries. Adding a small amount of PDMS-HT to the standard LIB electrolyte leads to improved specific capacity as well as improved capacity retention over prolonged cycles. There is also a slight increase in Li⁺ ion conductivity when PDMS-HT is added. Also, the PDMS-HT additive allows the formation of a more stable solid electrolyte interface (SEI) layer that enables the LIB cells to be cycled for longer cycles with minimal capacity fading. This combination of improved ionic conductivity and stable SEI layer formation due to the PDMS-HT additive, makes it an excellent candidate for an electrolyte additive for lithium ion batteries.     

锂电池中负极表面固体电解质膜的SERS研究

本文对锂电池中负极材料表面固体电解质膜 (SEI膜 )的SERS谱进行了研究 :极化低电位下对贵重金属的研究表明 ,非水电解质溶液中痕量水的存在将对SEI膜产生重要影响。在微量水存在的情况下 ,RCOCO2 Li不是SEI膜的稳定成份 ,Li2 CO3、LiF、LiOH或LiOH·H2 O等物种才是其稳定组成。进一步的研究表明 :SEI膜的某些谱带具有不同的光吸收特性 ;它是对外界条件非常敏感的一种表面膜。通过对比分析 ,SEI膜的特征谱带得到了进一步归属 ,并对其形成机理做了讨论。     

Identification of solid electrolyte interphase formed on graphite electrode cycled in trifluoroethyl aliphatic carboxylate-based electrolytes for low-temperature lithium-ion batteries

Trifluoroethyl aliphatic carboxylates with different length of carbon-chain in acyl groups have been introduced into carbonate-based electrolyte as co-solvents to improve the low-temperature performance of lithium-ion batteries, both in capacity retention and lowering polarization of graphite electrode. To identify the further influence of trifluoroethyl aliphatic carboxylates on graphite electrode, the components and properties of the surface film on graphite electrode cycled in different electrolytes are investigated using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. The IR and XPS results show that the chemical species of the solid electrolyte interphase (SEI) on graphite electrode strongly depend on the selection of co-solvent. For instance, among those species, the content of RCOOLi increases with an increasing number of carbon atoms in RCOOCH₂CF₃ molecule, wherein R was an alkyl with 1, 3, or 5 carbon atoms. We suggest that the thickness and components of the SEI film play a crucial role on the enhanced low-temperature performance of the lithium-ion batteries.     

TG-MS analysis on thermal decomposable components in the SEI film on Cr2O3 powder anode in Li-ion batteries

The thermal decomposable species in the solid electrolyte interphase (SEI) film on Cr₂O₃ powder anode at different lithiated and delithiated states in the first cycle were analyzed by thermogravimetry and mass spectrometry (TG-MS) technique. The weight loss ratio in a fully lithiated Cr₂O₃ electrode during TG measurement at 50–500 °C is 8.9 wt%, which is decreased to 1.5 wt% for a fully delithiated Cr₂O₃ electrode. This indicates that the SEI film on Cr₂O₃ powder anode is decomposed electrochemically upon delithiation. The main gas products are CH₂=CH₂, CO₂, and CH₃-containing volatile species in thermal reaction. They are released step-by-step in four characteristic temperature regions, which were originated mainly from oligomer and polyethylene-oxide-like species, partly from ROCO₂Li. It is also observed that the amount of thermal decomposable components in the SEI film on the fully lithiated Cr₂O₃ powder electrode is much higher than that on graphite and hard carbon anodes, indicating different SEI features of transition metal oxide anodes.     

Intercalation of lithium ions into bulk and powder highly oriented pyrolytic graphite

The electrochemical reactions of highly oriented pyrolytic graphite (HOPG) bulk and powder electrodes in 1 M LiPF₆ 1:1 EC/DMC solution were investigated and the results show that the intercalation reaction of lithium ion into HOPG electrode occurs only at the edge plane and SEI formation reaction on the basal plane is negligible in comparison with that on the edge plane. The active surface area of HOPG powder electrode could be deduced by comparing the peak area (consumed charge for SEI formation) at potential of 0.5 V on voltammograms with that of bulk HOPG edge electrode. The diffusion coefficients of lithium ion in HOPG bulk layers and in HOPG powder was for the first time measured by use of electrochemical impedance spectra and potential step chronamperameter methods. It was found that the diffusion coefficients of lithium in HOPG were in the range of 10⁻¹¹-10⁻¹² cm² s⁻¹ for the lithium-HOPG intercalation compounds at potentials from 0.2 (vs. Li/Li⁺) to 0.02 V, decreasing with the increase of lithium intercalation degree. A good agreement was obtained between the results from bulk and powder HOPG electrodes by electrochemical impedance spectra method.     

Impacts of lithium tetrafluoroborate and lithium difluoro(oxalate)borate as additives on the storage life of Li-ion battery at elevated temperature

The impacts of boron-based Li salt additives including lithium tetrafluoroborate (LiBF₄) and lithium difluoro(oxalate)borate (LDFOB) on the storage life of Li-ion battery at elevated temperature are investigated. Adding 1 wt% additives in the electrolyte significantly affects the storage life of the LiNi_0.8Co_0.15Al_0.05O₂/graphite full cell at 55 °C. The anode solid electrolyte interphase (SEI), preventing the loss of Li⁺ and e^? in anode, is the key factor affecting the storage life. The formation and aging of SEI on the graphite anode with and without additives are investigated. It is found that the SEI formed with the addition of LiBF₄ is thick and loose due to LiF crystals produced by the decomposition of LiBF₄ and the SEI cannot prevent the Li⁺ and e^? loss in anode and the decomposition of the electrolyte solvent, resulting in shorter storage life of the battery. On the contrary, the SEI formed with the addition of LDFOB is thick and compact due to formation of the lithium oxalate in the SEI, produced by the decomposition of LDFOB. The SEI efficiently inhibits decomposition of the electrolyte solvent on anode and makes a longer storage life of the battery.     

Characterization of the surface of positive electrodes for Li-ion batteries using 7Li MAS NMR

The growth and evolution of the interphase, due to contact with the ambient atmosphere or electrolyte, are followed using ⁷Li magic-angle spinning nuclear magnetic resonance (MAS NMR) in the case of two materials amongst the most promising candidates for positive electrodes for lithium batteries: LiFePO₄ and LiMn_0.5Ni_0.5O₂. The use of appropriate experimental conditions to acquire the NMR signal allows observing only the «diamagnetic» lithium species at the surface of the grains of active material. The reaction of LiMn_0.5Ni_0.5O₂ with the ambient atmosphere or LiPF₆ (1 M in Ethylene Carbonated/DiMéthyl Carbonate (EC/DMC)) electrolyte is extremely fast and leads to an important amount of lithium-containing diamagnetic species compared to what can be observed in the case of LiFePO₄. The two studied materials display a completely different surface chemistry in terms of reactivity and/or kinetics of the surface towards electrolyte. Moreover, these results show that MAS NMR is a very promising tool to monitor phenomena taking place at the interface between electrode and electrolyte.     

Electrochemical characteristics of amorphous silicon thin film electrode with fluoroethylene carbonate additive

The electrochemical and compositional changes of a solid electrolyte interphase (SEI) layer formed on the surface of silicon thin film are investigated in order to determine the effect of the content of fluoroethylene carbonate (FEC) additive in the electrolyte. Comparisons are made with FEC-free electrolyte, in which the major components are (CH₂OCO₂Li)₂ and Li₂CO₃. The (CH₂OCO₂Li)₂ and Li₂CO₃ of the SEI layer in the FEC-containing electrolyte decreases, and polycarbonate and LiF increase relatively with the repression of –OCO₂Li groups. The additive affects the composition of the SEI layer, which leads to lower resistance. The electrochemical performance regarding cycle retention, coulombic efficiency, rate capability, and discharge capacity in the FEC-containing cell are significantly enhanced compared to that of the FEC-free electrolyte. The observed optimum FEC concentration in the electrolyte is 1.5%, due to the reduced charge transfer and SEI resistance in our experimental range.     

XPS, XRD and SEM characterization of a thin ceria layer deposited onto graphite electrode for application in lithium-ion batteries

Thin ceria layer deposited by electro-precipitation onto graphite was synthesised and characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electro-precipitated ceria has a cubic structure with nanocrystallites of about 6 nm. The SEM analyses shows that the ceria layer reflects the morphology of the graphite electrode, exhibits small cracks usually found on the electro-precipitated films but covers almost completely the surface of the graphite. The ceria layer is composed of 75% Ce(IV) and 25% Ce(III) oxides as indicated by the XPS analyses. Cyclic voltammetry and galvanostatic charge-discharge tests in ethylene carbonate/dimethyl carbonate (1/1) (wt/wt) in the presence of 1 M LiPF₆ show that reversible lithium insertion and deinsertion occurs in the graphite/ceria electrode and that the ceria layer on the graphite electrode prevents from the loss of capacity during the first four cycles. The reduction of the electrolyte occurs at about 0.7 V vs Li/Li⁺ on both electrodes but XPS and SEM analyses show that the SEI layer is thin and not as homogenous on the graphite as on the graphite/ceria electrode. The composition of the SEI layer on the graphite/ceria electrode, mainly composed of Li₂CO₃, ROCO₂Li, R-CH₂OLi and LiF, is different than those obtained on the graphite.     

A lithium salt additive Li<Subscript>2</Subscript>ZrF<Subscript>6</Subscript> for enhancing the electrochemical performance of high-voltage LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode

In this work, Li₂ZrF₆, a lithium salt additive, is reported to improve the interface stability of LiNi_0.5Mn_1.5O₄ (LNMO)/electrolyte interface under high voltage (4.9 V vs Li/Li⁺). Li₂ZrF₆ is an effective additive to serve as an in situ surface coating material for high-voltage LNMO half cells. A protective SEI layer is formed on the electrode surface due to the involvement of Li₂ZrF₆ during the formation of SEI layer. Charge/discharge tests show that 0.15 mol L^?1 Li₂ZrF₆ is the optimal concentration for the LiNi_0.5Mn_1.5O₄ electrode and it can improve the cycling performance and rate property of LNMO/Li half cells. The results obtained by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) demonstrate that Li₂ZrF₆ can facilitate the formation of a thin, uniform, and stable solid electrolyte interface (SEI) layer. This layer inhibits the oxidation decomposition of the electrolyte and suppresses the dissolution of the cathode materials, resulting in improved electrochemical performances.     

原位聚合法制备凝胶型离子液体/PMMA聚合物电解质

采用原位聚合法制备了含有N-甲基、丙基哌啶双三氟甲磺酰亚胺离子液体的凝胶型聚合物电解质．利用SEM和XPS测试了电解质膜与LiFePO₄电极的界面状态,充放电循环后,在电解质膜与LiFePO₄之间有一层薄膜,这层薄膜中含有N和S元素．结果表明,随着充放电的不断进行,凝胶型电解质中未聚合的甲基丙烯酸甲酯与电极表面的锂离子之间发生电子转移,形成SEI膜,至少要三个循环后才能形成稳定的SEI膜．随着SEI膜的增厚,放电容量增加,阻碍了电子转移,使系统更加的稳定．在不同     

Negative electrodes in rechargeable lithium ion batteries — Influence of graphite surface modification on the formation of the solid electrolyte interphase

Rechargeable lithium ion cells operate at voltages of ∼4.5 V, which is far beyond the thermodynamic stability window of the battery electrolyte. Strong electrolyte reduction and corrosion of the negative electrode has to be anticipated, which leads to irreversible loss of electroactive material and electrolyte, and thus strongly deteriorates cell performance. To minimize these reactions, negative electrode and electrolyte components have to be combined bringing about the electrolyte reduction products to form an effectively protecting film at the anode/electrolyte interface. This film hinders further electrolyte decomposition reactions and acts as membrane for the lithium cations, i.e., behaves as asolidelectrolytei2nt erphase (SEI). The present paper gives a review of our recent work in the field of negative electrodes in lithium ion batteries. The effects of the graphite anode surface and graphite anode surface modification on the formation of the SEI are discussed in detail by using the example: modification with carbon dioxide. Paper presented at the 6th Euroconference on Solid State Ionics, Cetraro, Calabria, Italy, Sept. 12–19, 1999.     

Effect of sodium salt addition upon electrochemical behavior of natural graphite

Despite the reported enhanced electrochemical behavior of graphite anodes due to the addition of NaClO₄ salts in to the electrolytes used in lithium battery applications, a detailed investigation upon the effect of addition of NaPF₆ salt in an electrolyte containing 1 M LiPF₆ in 1:1 V/V EC:DEC has resulted in inferior electrochemical behavior of graphite, i.e., quite contrast to the reported behavior of improved effects of addition of NaClO₄ into 1 M LiClO₄ solution, the addition of 0.22 mol dm⁻³ NaPF₆ salt has been found to reduce the capacities of lithium-ion cells containing 1 M LiPF₆ in 1:1 V/V EC:DEC. Towards this study, cells fabricated with and without the addition of 0.22 mol dm⁻³ NaPF₆ in 1 M LiPF₆ (1:1 V/V EC:DEC) were subjected to a systematic charging at a constant C/10 rate and discharging of cells at four different rates, viz., C/5, C/2 and C rates at the end of every 5 cycles. The observed results of the charge-discharge studies up to 15 cycles are discussed in this preliminary communication.     

Effect of SO<Subscript>2</Subscript> and CO<Subscript>2</Subscript> additives on the cycle performances of commercial lithium-ion batteries

The effects of SO₂ and CO₂ additives in electrolytes on the cycle properties of liquid-state Al-plastic film lithium-ion batteries were first investigated. The experimental electrolytes were added with different amounts of SO₂ and CO₂. The baseline electrolyte was 1 mol L⁻¹ LiPF₆ in ethylene carbonate/dimethylcarbonate/ethyl-methyl carbonate (1:1:1, by volume), and graphite was used as anode. The main analysis tools were cycling test, rate capability, internal resistance test, low-temperature performance, and thermal stability. The results showed that both of the additives could promote to form an excellent solid electrolyte interface film on the surface of graphite anode, leading to excellent cycle performances, the capacity retentions of CO₂ and S5 were 94% and 97% after 400 cycles, respectively. Besides, the results also exhibited that the electrochemical performances of internal resistance, rate capability, low-temperature performance, and thermal stability were not changed significantly by the use of SO₂ and CO₂ as electrolyte additives.     

Effects of various LiPF<Subscript>6</Subscript> salt concentrations on PEO-based solid polymer electrolytes

In this research, various weight percents of LiPF₆ are incorporated into PEO-based polymer electrolyte system. Thin film electrolytes are prepared via solution casting technique and characterized by FTIR, XRD and DSC analyses in order to study their complex behaviour. The amorphicity of the electrolytes are measured by DC impedance. The results reveal that the conductivity increases with increasing temperature when the salt concentration increases to 20 wt.%. The conductivity for 20 wt.% of salt remains similar to the conductivity of 15 wt.% of salt at 318 K. Impedance studies show that the conductivity increases with increasing LiPF₆ concentration, whereas XRD studies reveal that the phase changes from crystalline to amorphous when LiPF₆ concentration increases. DSC studies indicate a decrease in T _m with increasing LiPF₆ concentration. Finally, the complexation process is examined using FTIR.     

Ionic liquid-based electrolyte with dual-functional LiDFOB additive toward high-performance LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> batteries

Manganese oxide-based cathodes are one of the most promising lithium-ion battery (LIB) cathode materials due to their cost-effectiveness, high discharge voltage plateau (above 4.0 V vs. Li/Li⁺), superior rate capability, and environmental benignity. However, these batteries using conventional LiPF₆-based electrolytes suffer from Mn dissolution and poor cyclic capability at elevated temperature. In this paper, the ionic liquid (IL)-based electrolytes, consisting of 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfon)imidate (PYR_1,4-TFSI), propylene carbonate (PC), lithium bis(trifluoromethanesulfon)imide (LiTFSI), and lithium oxalyldifluoroborate (LiDFOB) additive, were explored for improving the high temperature performance of the LiMn₂O₄ batteries. It was demonstrated that LiTFSI-ILs/PC electrolyte associated with LiDFOB addition possessed less Mn dissolution and Al corrosion at the elevated temperature in LiMn₂O₄/Li batteries. Cyclic voltammetry and electrochemical impedance spectroscopy implied that this kind of electrolyte also contributed to the formation of a highly stable solid electrolyte interface (SEI), which was in accordance with the polarization measurement and the Li deposition morphology of the symmetric lithium metal cell, thus beneficial for improving the cycling performance of the LiMn₂O₄ batteries at the elevated temperature. Cyclic voltammetry and electrochemical impedance spectroscopy implied that the cells using this kind of electrolyte exhibited better interfacial stability, which was further verified by the polarization measurement and the Li deposition morphology of the symmetric lithium metal cell, thus beneficial for improving the cycling performance of the LiMn₂O₄ batteries at the elevated temperature. These unique characteristics would endow this kind of electrolyte a very promising candidate for the manganese oxide-based batteries.     

Effect of heptamethyldisilazane on the electrochemical performance of LiMn2O4/Li

The effect of heptamethyldisilazane as an electrolyte stabilizer on the cycling performance of a LiMn₂O₄/Li cell at different rates at 30 °C and the storage performance at 60 °C is investigated systematically based on conductivity test, linear sweep voltage, electrochemical impedance spectroscopy, scanning electron microscopy, X-ray diffraction, and charge–discharge measurements. The results show that heptamethyldisilazane added into the LiPF₆-based electrolyte can increase the stability of the original electrolyte; coulomb efficiency, the initial discharge capacity, and cycling performance at different rates in a sense, meanwhile, improve the storage performance at elevated temperature, although the C-rate performance of the cell is a little worse than that without heptamethyldisilazane in the electrolyte. When the LiMn₂O₄/Li cell with heptamethyldisilazane in the LiPF₆-based electrolyte stored at 60 °C for a week cycles 300 times, the capacity retention is up to 91.18 %, which is much higher than that (87.18 %) without the additive in the electrolyte. This is mainly due to the lower solid electrolyte interface resistance (R _f) in the cell, followed by the better morphology and structure of the cathode after storage at 60 °C for a week compared with the LiMn₂O₄/Li cell without heptamethyldisilazane.     

Electrolytic behavior and application to lithium batteries of monofluorinated dimethyl carbonate

Dimethyl carbonate (DMC) was fluorinated by F₂ gas (direct fluorination) to form four fluorinated DMC derivatives, such as monofluorinated DMC (MFDMC), two difluorinated DMCs (DFDMC(a) and DFDMC(b)) and trifluorinated DMC (TFDMC). The electrolytic behavior and charge–discharge characteristics of the lithium electrode were examined in MFDMC and MFDMC-ethylene carbonate (EC) equimolar binary solutions. The dielectric constant and viscosity of MFDMC are higher than those of DMC. This means that the molecular interaction in MFDMC becomes larger due to the introduction of a high electron withdrawing fluorine atom. In addition, oxidation durability of MFDMC is higher than that of DMC. The specific conductivity in EC-MFDMC equimolar binary solution containing 1 M LiPF₆ is 8.5 mS cm^− 1 at 25 °C which means a good electrolyte for lithium batteries. The lithium electrode cycling efficiency in EC-MFDMC equimolar binary solution containing 1 M LiPF₆ is higher than 70%. The surface of the film formed on the electrode in the solution is homogeneous, and consists of the uniform and small grain size.     

Neural networks for Nyquist plots prediction in a nanocomposite polymer electrolyte (PEO–LiPF<Subscript>6</Subscript>–EC–CNT)

In this study, the Nyquist plots for nanocomposite polymer electrolyte system (polyethylene oxide (PEO)–lithium hexafluorophosphate (LiPF₆)–ethylene carbonate (EC)–carbon nanotube (CNT)), which was produced by using solution cast technique, were obtained using Bayesian neural network. First, to prepare the training and test set of the network, some results were experimental obtained and recorded. In the experiment, PEO, LiPF₆, EC, and CNT were mixed at various ratios. The effects of the chemical composition on the impedance spectra of polymer electrolyte system were investigated. In neural network training, different chemical composition and real impedance were used as inputs and imaginary impedance in the produced polymer electrolytes was used as outputs. After the training process, the test data were used to check system accuracy. As a result, the neural network was found successful for the prediction of imaginary impedance of nanocomposite polymer electrolyte system.