Formation and structure of sphene/titania composite coatings on titanium formed by a hybrid technique of microarc oxidation and heat-treatment

Sphene/titania composite coatings were fabricated on titanium by a hybrid technique of microarc oxidation (MAO) and heat treatment. The high-applied voltages promote the formation of sphene in the MAO coatings after heat-treatment. Heat treatment could change the surface morphology of the MAO coatings such as roughness, macropores size and density and the thickness of the MAO coatings. Increasing the heat-treatment temperature decreased the atomic concentration ratios of Ti/Si and Ti/Ca of the MAO coatings. The chemical states of Ti⁴⁺, Ca²⁺, Si²⁺ and O²⁻ were observed on all the coatings. Additionally, Ti²⁺ was detected in the MAO and heat-treated MAO coatings at 600 and 700 °C. The heat-treatment has obvious effect on the chemical states of Si, Ti and O elements due to the formation of sphene and oxidation of TiO phase of the MAO coating, but did not affect that of Ca. In the heat-treated MAO coatings at 800 °C (MAO-H8), the titanium surface shows a MAO top layer and oxidized interior layer. A concentration gradient in components in the MAO layer of the MAO-H8 coating was formed.     

Characteristic and biocompatibility of the TiO2-based coatings containing amorphous calcium phosphate before and after heat treatment

TiO₂-based coating containing amorphous calcium phosphate (CaP) was prepared on titanium alloy by microarc oxidation (MAO). The increase in the EDTA-2Na concentration was unfavorable for the crystallization of TiO₂. After heat treatment, the amorphous CaP was crystallized. The thickness of the MAO coatings did not change when heat-treated at 400, 600 and 700 °C; while it increased slightly after heat treatment at 800 °C due to the crystallization of amorphous CaP and growth of TiO₂. No apparent discontinuity between the coatings and substrates was observed at various heat-treatment temperatures, indicating the MAO coatings with good interfacial bonding to the substrate. The heat treatment did not alter the chemical composition of the MAO coating and the chemical states of Ti, Ca and P elements. However, it increased the roughness (Ra) of the MAO coating and improved the wetting ability of the MAO coating. In this work, preliminary investigation of the MG63 cell proliferation on the surface of the MAO and heat-treated MAO coatings was conducted. The MAO coating surface with about Ra = 220 nm may be suitable for the MG63 cell adhesion and proliferation. The increased roughness of the heat-treated MAO coatings may result in a decrease in the ability for cell adhesion and proliferation.     

Fabrication and characterization of rod-like nano-hydroxyapatite on MAO coating supported on Mg-Zn-Ca alloy

The poor corrosion resistance of magnesium alloys is a dominant problem that limits their clinical application. In order to solve this challenge, micro-arc oxidation (MAO) was used to fabricate a porous coating on magnesium alloys and then electrochemical deposition (ED) was done to fabricate rod-like nano-hydroxyapatite (RNHA) on MAO coating. The cross-section morphology of the composite coatings and its corresponding energy dispersion spectroscopy (EDS) surficial scanning map of calcium revealed that HA rods were successfully deposited into the pores. The three dimensional morphology and scanning electron microscopy (SEM) image of the composite coatings showed that the distribution of the HA rods was dense and uniform. Atomic force microscope (AFM) observation of the composite coatings showed that the diameters of HA rods varied from 95 nm to 116 nm and the root mean square roughness (RMS) of the composite coatings was about 42 nm, which were favorable for cellular survival. The bonding strength between the HA film and MAO coating increased to 12.3 MPa, almost two times higher than that of the direct electrochemical deposition coating (6.3 MPa). Compared with that of the substrate, the corrosion potential of Mg-Zn-Ca alloy with composite coatings increased by 161 mV and its corrosion current density decreased from 3.36 × 10⁻⁴ A/cm² to 2.40 × 10⁻⁷ A/cm² which was due to the enhancement of bonding strength and the deposition of RNHA in the MAO pores. Immersion tests were carried out at 36.5 ± 0.5 °C in simulated body fluid (SBF). It was found that RNHA can induce the rapid precipitation of calcium orthophosphates in comparison with conventional HA coatings. Thus magnesium alloy coated with the composite coatings is a promising candidate as biodegradable bone implants.     

Surface modification of pure titanium by hydroxyapatite-containing composite coatings

Micro-arc oxidation (MAO) is commonly applied to modify the surface of titanium (Ti)-based medical implants with a bioactive and porous Ti oxide (TiO₂) coating. The study reports a new method of incorporating hydroxyapatite (HA) within the TiO₂ coating by MAO and alkali heat treatment (AHT) in the solution containing Ca ion and P ion. The morphology, composition and phase composition of the coatings were analyzed with scanning electron microscopy with energy-dispersive X-ray spectrometer and X-ray diffraction. Surface topography and roughness of the coatings were investigated by atomic force microscopy operated in the tapping mode. The results showed that TiO₂-based coatings were obtained on pure Ti by MAO with an electrolyte containing Ca ion and P ion; the prepared MAO coatings were mainly composed of Ca, P, O and Ti. AHT transformed Ca and P to HA crystals. In conclusion, the TiO₂/HA composite coatings can be obtained on the surface of pure Ti by MAO and AHT, and the addition of Ca ion and P ion to the AHT solution contributed to the formation of HA.     

Electrochemically assisted co-deposition of calcium phosphate/collagen coatings on carbon/carbon composites

Calcium phosphate (CaP)/collagen coatings were prepared on the surface of carbon/carbon (C/C) composites by electrochemically assisted co-deposition technique. The effects of collagen concentration in the electrolyte on morphology, structure and composition of the coatings were systematically investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transformed infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The adhesive strength of the coatings was also evaluated by scratch tests and tensile bond tests. It was demonstrated that the coatings of three-dimensional collagen network structure was formed on the C/C composites from the electrolyte containing collagen. The surface of the collagen network was covered by uniform CaP aggregates. The coatings were actually composites of CaP and collagen. Hydroxyapatite (HA) was a favorable composition in the coatings with the increase of the collagen concentration in the electrolyte. The formed collagen network increased the cohesive and adhesive strength of the coatings. The adhesive strength between the coatings and substrates increased as the collagen concentration in the electrolyte increased. The coatings prepared at the collagen concentration of 500 mg/L in the electrolyte were not scraped off until the applied load reached 32.0 ± 2.2 N and the average tensile adhesive strength of the coatings was 4.83 ± 0.71 MPa. After C/C coated with composite coatings (500 mg/L) being immersed in a 10⁻³ M Ca (OH)₂ solution at 30-33 °C for 96 h, nano-structured HA/collagen coatings similar to the natural human bone were obtained on the C/C.     

The effect of deposition temperature on the surface coverage and morphology of iron-phosphate coatings on low carbon steel

The influence of deposition temperature and concentration of NaNO₂ in the phosphating bath on the surface morphology and coverage of iron-phosphate coatings on low carbon steel was investigated. The phosphate coatings were chemically deposited on steel from phosphate bath at different temperatures (30-70 °C) and with the addition of different amounts of accelerator, NaNO₂ (0.1, 0.5 and 1.0 g dm⁻³). The morphology of phosphate coatings was investigated using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The composition of iron-phosphate coatings was determined using energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). Surface coverage was evaluated by the voltammetric anodic dissolution (VAD) technique.It was shown that the increase in temperature of the NaNO₂-free phosphating bath up to 70 °C caused an increase in surface coverage. The addition of NaNO₂ in the phosphating bath significantly increased the surface coverage of phosphate coatings deposited at temperatures lower than 50 °C. The phosphate crystals were of laminated and needle-like structures for deposits obtained at temperatures lower than 50 °C, while at higher temperatures needle-like structure was transformed to laminated structure. The increase in NaNO₂ concentration in the phosphating bath from 0.1 to 1.0 g dm⁻³ did not significantly increase the surface coverage, but decreased the crystals size, consequently favouring the phosphate nucleation and better packing of the crystals.     

Characterization of microarc oxidation coatings formed on AM60B magnesium alloy in silicate and phosphate electrolytes

Microarc oxidation coatings on AM60B magnesium alloy were prepared in silicate and phosphate electrolytes. Structure, composition, mechanical property, tribological, and corrosion resistant characteristics of the coatings was studied by scanning electron microscope (SEM), X-ray diffraction (XRD) and microhardness analyses, and by ball-on-disc friction and potentiodynamic corrosion testing. It is found that the coating produced from the silicate electrolyte is compact and uniform and is mainly composed of MgO and forsterite Mg₂SiO₄ phases, while the one formed in phosphate electrolyte is relatively porous and is mainly composed of MgO phase. The thick coating produced from a silicate electrolyte possesses a high hardness and provides a low wear rate (3.55 × 10⁻⁵ mm³/Nm) but a high friction coefficient against Si₃N₄ ball. A relatively low hardness and friction coefficient while a high wear rate (8.65 × 10⁻⁵ mm³/Nm) is recorded during the testing of the thick coating produced from a phosphate electrolyte. Both of these types of coatings provide effective protection for the corrosion resistance compared with the uncoated magnesium alloy. The coating prepared from the silicate electrolyte demonstrates better corrosion behavior due to the compacter microstructure.     

Formation of titania composite coatings on carbon steel by plasma electrolytic oxidation

Titania composite coatings were prepared on carbon steel by plasma electrolytic oxidation in silicate electrolyte and aluminate electrolyte with titania powers doping in the electrolytes. The microstructure of the coatings was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The properties of the coatings including bond strength, thickness, thermal shock resistance and corrosion resistance varying with the quantities of titania powers in the electrolytes were studied. Investigation results revealed that the coating obtained in silicate electrolyte was composed of anatase-TiO₂, rutile-TiO₂ crystal phases and some Fe, Si, P elements; coating obtained in aluminate electrolyte consisted of anatase-TiO₂, Al₂TiO₅ and some Fe, P elements. Coatings obtained in two types of electrolytes show porous and rough surface. With increasing the concentration of titania powers in the electrolytes, the coating surface first became more compact and less porous and then became more porous and coarse. The bond strength and thickness were not strongly affected by concentration of titania powers in electrolytes. The valves were 23 MPa and for 66 μm for coatings obtained in aluminate electrolyte, and 21 MPa and 35 μm for coatings obtained in silicate electrolyte. Coatings obtained in silicate electrolyte showed a little better thermal shock resistance than those obtained in aluminate electrolyte and the best coatings were obtained with middle concentration of titania powers in the electrolytes. All coated samples showed better corrosion resistance than the substrate in 3.5 wt% NaCl solution. The best coatings were also obtained with middle concentration of titania powers doping in both electrolytes whose corrosion current density was decreased by 2 orders of magnitude compared with the substrate.     

Characterization of hybrid electrolytes prepared from the Li2S-P2S5 glasses and alkanediols

Inorganic-organic hybrid electrolytes were prepared by the mechanochemical method using the Li⁺ ion conductive 70Li₂S·30P₂S₅ glass and various alkanediols. Local structure of the prepared electrolytes was analyzed by FT-IR and Raman spectroscopy. The effects of the proportion and chain length of alkanediols on conductivity of the hybrid electrolytes were investigated. The hybrid electrolyte with 2 mol.% of 1,4-butanediol exhibited the conductivity of 9.7 × 10^− 5 S cm^− 1 at room temperature and the unity of lithium ion transference number. The use of alkanediols with shorter chain length was effective in increasing conductivity of hybrid electrolytes. The electrolyte using ethyleneglycol showed the highest conductivity of 1.1 × 10^− 4 S cm^− 1 at room temperature. Lowering glass transition temperature by incorporation of alkanediols is responsible for the enhancement of conductivity of hybrid electrolytes.     

Influence of FeSO4 concentration on thermal emissivity of coatings formed on titanium alloy by micro-arc oxidation

Ceramic coatings with high emission were fabricated on Ti6Al4V alloy by microarc oxidation (MAO) with additive FeSO₄ into the electrolyte. The microstructure, chemical composition and chemical state of the coatings were determined by SEM, XRD, EDS and XPS, respectively. The bonding strength between the coating and substrate was studied by tensile strength test, together with the thermal shock resistance of the coating. The results showed that Fe content in the coating layer significantly affect its thermal emissivity. The relative content of Fe in the coatings surface increased at first and then decreased with increasing the concentration of FeSO₄ in electrolytes, so does the emissivity of the coatings. The bonding strength became weaker with increasing the concentration of FeSO₄. In addition, the coating remains stable over 40 cycles of thermal shocking. The coating formed at 3 g/L FeSO₄ demonstrates the highest an average spectral emissivity value around of 0.87, and bonding strength higher than 33 MPa.     

Adsorption and desorption of Ca and PO4 species from SBFs on RF-sputtered calcium phosphate thin films

RF magnetron sputtering of calcium phosphate (CaP) coatings is a promising technique to apply thin bioactive films on bulk implant materials. In this paper the properties of the interface between RF sputtered coatings and simulated body fluids (SBFs) are related to the ability to form CaP crystals on the coating surface. Two types of coatings were compared: coatings with a low Ca over P ratio (∼0.8; CaP_low), which remain inert when immersed in SBF₂ (i.e. SBF with twice the Ca and PO₄ concentrations), and coatings with a high Ca over P ratio (1.6; CaP_high), which show the formation of CaP crystals on their surface within 2 h. Low energy ion scattering (LEIS) and radioactive labeling of the SBFs combined with liquid scintillation counting (LSC) allowed us to study very accurately the composition of the adsorbates of both coating groups after 10 min of immersion in SBF₂. For the adsorbate on CaP_high and CaP_low coatings coverages were found consistent with ionic adsorption and Ca/P ratios of 1.24 ± 0.02 and 2.17 ± 0.10, respectively. Adsorption was found to be reversible over the studied immersion period. After an induction period of 40 min a CaP precipitate started to form on the CaP_high coatings with a Ca/P ratio of 1.30 ± 0.02. Further, no significant desorption of coating species was observed during this induction period.     

Surface phenomena of HA/TiN coatings on the nanotubular-structured beta Ti-29Nb-5Zr alloy for biomaterials

Surface phenomena of HA/TiN coatings on the nanotubular-structured beta Ti-29Nb-5Zr alloy for biomaterials have been investigated by several experimental methods. The nanotubular structure was formed by anodizing the Ti-29Nb-5Zr alloy in 1 M H₃PO₄ electrolytes with 1.0 wt.% NaF at room temperature. Hydroxyapatite (HA)/titanium nitride (TiN) films were deposited on Ti-29Nb-5Zr alloy specimens using a magnetron sputtering system. The HA target was made of human tooth-ash by sintering at 1300 °C for 1 h, and the HA target had an average Ca/P ratio of 1.9. The HA/TiN depositions were performed, using the pure HA target, on Ti-29Nb-5Zr alloy following the initial deposition of a TiN buffer layer coating. Microstructures and nanotubular morphology of the coated alloy specimens were examined by FE-SEM, EDX, XRD, and XPS. The Ti-29Nb-5Zr alloy substrate had small grain size and preferred orientation along the drawing direction. The HA/TiN coating was stable with a uniform morphology at the tips of the nanotubes.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.     

Influence of treating frequency on microstructure and properties of Al2O3 coating on 304 stainless steel by cathodic plasma electrolytic deposition

Alumina ceramic coatings were fabricated on 304 stainless steel by cathodic plasma electrolytic deposition (CPED). Influence of treating frequency of the power supply on the microstructure and properties of the coatings were studied. The results indicated that coatings obtained at various frequencies on 304 stainless steels were all composed of α-Al₂O₃ and γ-Al₂O₃, and α-Al₂O₃ was the dominant phase. The contents of α-Al₂O₃ decreased gradually in a very small rate with increasing the frequency and γ-Al₂O₃ gradually increased. The surface of alumina ceramic coating was porous. With increasing the frequency, the coating surface gradually became less rough and more compact, resulting in low surface roughness. The bonding strength of Al₂O₃ coating was higher than 22 MPa and was not strongly affected by treating frequency. With increasing the frequency, the alumina coated steels showed better and gradually increasing corrosion resistance than the uncoated one in 3.5% NaCl solution. The coating steel with desirable corrosion resistance was obtained at 800 Hz whose corrosion current potential and corrosion density were −0.237 V and 7.367 × 10⁻⁸ A/cm², respectively.     

Synthesis and utilization of chitin-humic acid hybrid as sorbent for Cr(III)

New types of hybrid material have been synthesized by using four different methods of immobilization of humic acid (HA) on chitin. The most stable hybrid material toward the change of medium acidity was then utilized as sorbent for Cr(III).The HA was extracted from peat soil of Gambut District, South Kalimantan, Indonesia, using the recommended procedure of International Humic Substances Society (IHSS), while the chitin was isolated from crab shell waste through deproteination using 3.5% (w/v) NaOH and followed by removal of inorganic impurities using 1 M HCl. The four methods of immobilization of HA on chitin were (i) Method A: chitin powder (4 g) was gently poured into the stirred solution of 0.4 g HA in 40 mL of 0.01 M NaOH. After overnight stirring, the solid was separated, washed with water, and dried in oven at 70 °C. (ii) Method B: gelatinous chitin (40 g) in 250 mL of 0.5 M HCl was reacted with HA (4 g) in 500 mL of 0.5 M NaOH and aged for 24 h. The product was washed with water and dried. (iii) Method C: HA powder (0.5 g) was mixed with the stirred gel of chitin (2.5 g) in 60 mL of CaCl₂ saturated methanol and the mixture was then washed with the mixed solution of 25 mL of 2 M sodium citrate and ethylene glycol 1:1. The solid was separated, washed with water, and dried. (iv) Method D: the solution of HA (0.056 g) in 10 mL of 0.01 M NaOH was reacted with the gel of chitin (0.2 g) in 10 mL of CaCl₂ saturated methanol. After 24 h stirring, the solid was separated from the reaction medium, washed with the mixed solution of 2 M sodium citrate and ethylene glycol 1:1, and followed by washing with water and drying. Parameters investigated in this study consisted of the stability test of the immobilized HA, as well as the rate constant (k₁), capacity (b), and energy (E) of sorption as well as the rate constant of desorption (k₋₁). The k₁ and k₋₁ were determined according to a kinetic model of first order sorption reaching equilibrium, while the b and E were determined according to the Langmuir isotherm model.Compared to HA, Methods, A, C, and D; Method B produced the most stable immobilization of HA on chitin. The hybrid material (Chitin-HA) synthesized through Method B was stable in the acidity range that equivalent to pH 2.0-11.0. At the acidity giving maximum sorption, i.e. pH 5, the presence of immobilized HA on the Chitin-HA enhanced more than three times the k₁ and k₋₁, i.e. from 0.057 min⁻¹ and 8.51 × 10⁻⁴ (min⁻¹) (mol/L) for chitin to 0.183 min⁻¹ and 3.27 × 10⁻³ (min⁻¹) (mol/L) for the Chitin-HA. On the contrary, the presence of HA on Chitin-HA only gave small increase on b and small decrease on E. The values of b and E for Cr(III) on chitin were 1.45 × 10⁻² mol/g and 23.12 kJ/mol, respectively, while those on Chitin-HA were 1.78 × 10⁻² mol/g and 19.95 kJ/mol, respectively.     

Role of pH and calcium ions in the adsorption of an alkyl N-aminodimethylphosphonate on steel: An XPS study

The role of pH and calcium ions in the adsorption of an alkyl N-aminodimethylphosphonate on mild steel (E24) surfaces was investigated by XPS. Fe 2p_3/2 and O 1s spectra show that the oxide/hydroxide layer developed on the steel surface, immersed in the diphosphonate solution (7 ≤ pH ≤ 13, without Ca²⁺) or in a filtered cement solution (pH 13, 15.38 mmol l⁻¹ of Ca²⁺), consists of Fe₂O₃, covered by a very thin layer of FeOOH (goethite). The total thickness of the oxide/hydroxide layer is ∼3 nm and is independent of the pH and the presence/absence of Ca²⁺. In the absence of Ca²⁺ ions, the N 1s and P 2p spectra reveal that the adsorption of the diphosphonate on the outer layer of FeOOH takes place only for pH lower than the zero charge pH of goethite (7.55). At pH 7, the adsorbed diphosphonate layer is continuous and its equivalent thickness is ∼24 Å (monolayer). In the presence of Ca²⁺ ions, the C 1s and Ca 2p signals indicate that calcium is present on the steel surface as calcium phosphonate (and Ca(OH)₂, in very small amount). The adsorption of the diphosphonate molecules on the steel surface is promoted in alkaline solution (pH > 7.55) by the doubly charged Ca²⁺ ions that bridge the O⁻ of goethite and the P-O⁻ groups of the diphosphonate molecules. The measured values for the Ca/P intensity ratio are in the range 0.75-1, which suggests that the diphosphonate molecules are adsorbed on steel forming a polymer cross-linked by calcium ions through their phosphono groups. In the presence of Ca²⁺ ions in alkaline solution, the adsorbed diphosphonate layer is discontinuous and the surface coverage is found to be ∼34%.     

An investigation into the effects of high laser fluence on hydroxyapatite/calcium phosphate films deposited by pulsed laser deposition

Pulsed laser deposited mixed hydroxyapatite (HA)/calcium phosphate thin films were prepared at room temperature using KrF laser source with different laser fluence varying between 2.4 J/cm² and 29.2 J/cm². Samples deposited at 2.4 J/cm² were partially amorphous and had rough surfaces with a lot of droplets while higher laser fluences showed higher level of crytallinity and lower roughness of surfaces of obtained samples. Higher laser fluences also decreased ratio Ca/P of as-deposited samples. X-ray photoelectron spectroscopy (XPS) revealed traces of carbonate groups in obtained samples, which were removed after thermal annealing. The decomposition of HA into TCP was observed to start at about 400 °C. The formation of new crystalline phase of HA was found after annealing as well. The cracks observed on surface of sample deposited at 29.2 J/cm² after annealing indicated that the HA/ calcium phosphate films deposited at higher laser energy densities were probably more densed.     

Ultra-hard ceramic coatings fabricated through microarc oxidation on aluminium alloy

Ultra-hard ceramic coatings with microhardness of 2535 Hv have been synthesized on the Al alloy substrate by microarc oxidation (MAO) technique. The effects of anodic current density (j_a) and the ratio of cathodic to anodic current density (j_c/j_a) on the mechanical and corrosion resistance properties of MAO coatings have been studied by microhardness and pitting corrosion tests, respectively. In addition, the phase composition and microstructure of the coatings were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results show that the coatings prepared at high anodic current density consist mainly of α-Al₂O₃, while those fabricated at low anodic current density are almost composed of γ-Al₂O₃. Microhardness test shows that the coatings have high microhardness, and the highest one is found in the coating formed at j_a = 15 A/dm² and j_c/j_a = 0.7. Pitting corrosion test shows that the structure of coatings is strongly influenced by the varying j_c/j_a.     

Low-temperature oxidation of SiGe by liquid-phase deposition

Low-temperature silicon dioxide (SiO₂) films were grown on silicon germanium (SiGe) surfaces using the liquid-phase deposition (LPD) method. The growth solutions of LPD-SiO₂ are hydrofluorosilicic acid (H₂SiF₆) and boric acid (H₃BO₃). It was found that the growth rate increases with increasing temperature and concentration of H₃BO₃. The Auger electron spectroscopy profile shows that no pileup of Ge atoms occurs at the interface of SiO₂/SiGe after the LPD-SiO₂ growth. Al/LPD-SiO₂/p-SiGe MOS capacitors were prepared to determine capacitance-voltage (C-V) and current-voltage (I-V) characteristics. In our experiments, a low leakage current density of 8.69 × 10⁻⁹ A/cm² under a 2 MV/cm electric field was observed. Such a value is much smaller than those of plasma- and thermal-oxides as a result of no plasma damage and a lower growth temperature. Moreover, lower oxide charges and interface charge densities of 3.82 × 10¹⁰ cm⁻² and 1.12 × 10¹¹ eV⁻¹ cm⁻², respectively, were achieved in our LPD-SiO₂ compared to direct photochemical-vapor-deposition-SiO₂.     

Structure, thermal and transport properties of PVAc-LiClO4 solid polymer electrolytes

The lithium ion conducting solid polymer electrolytes (SPE) based on PVAc-LiClO₄ of various compositions were prepared by solution casting technique. Structure and surface morphology characterization were studied by X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) measurements, respectively. Thermal and conductivity behavior of polymer-salt complexes were studied by employing differential scanning calorimetry (DSC) and ac impedance measurements, respectively. XRD and SEM analyses indicate the amorphous nature of the polymer-salt complexes. DSC measurements show decrease in T_g with the increase in LiClO₄ concentrations. The bulk conductivity of the PVAc:LiClO₄ polymer electrolytes was found to vary between 7.6×10⁻⁷ and 6.2×10⁻⁵ S cm⁻¹ at 303 K with the increase in salt concentration. The temperature dependence of the polymer electrolyte complexes appear to obey Arrhenius law.