Nanostructured WO3 thin film as a new anode material for lithium-ion batteries

Nanostructured WO₃ thin film has been successfully fabricated by radio-frequency magnetron sputtering method and its electrochemistry with lithium was investigated for the first time. The reversible discharge capacity of WO₃/Li cells cycled between 0.01 V and 4.0 V was found above 626 mAh/g during the first 60 cycles at the current density 0.02 mA/cm². By using X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy and selected-area electron diffraction measurements, the reversible conversion of WO₃ into nanosized metal W and Li₂O was revealed. The high reversible capacity and good recyclability of WO₃ electrode made it become a promising cathode material for future rechargeable lithium batteries.     

VO2-WO3 nanocomposite thin films synthesized by pulsed laser deposition technique

Pure VO₂ and VO₂-WO₃ composite thin films were grown on quartz substrate by pulsed laser deposition (PLD) technique. The influence of varying WO₃ molar concentration in the range from x = 0.0 to x = 0.4 on structural, electrical and optical properties of VO₂-WO₃ nanocomposite thin films has been systematically investigated. X-ray diffraction studies reveal the single crystalline monoclinic VO₂ phase (m-VO₂) up to 10% of WO₃ content whereas both m-VO₂ as well as h-WO₃ (hexagonal WO₃) phases were present at higher WO₃ content (0.2 ≤ x ≤ 0.4). Optical transmittance spectra of the films showed blue shift in the absorption edge with increase in WO₃ content. Temperature dependence of resistivity (R-T) measurements indicates significant variation in metal-insulator transition temperature, width of the hysteresis, and shape of the hysteresis curve. Cyclic Voltammetry measurements were performed on VO₂-WO₃ thin films. A direct correlation between V/W ratio and structure-property relationship was established. The present investigations reveal that doping of WO₃ in VO₂ is effective to increase the optical transmittance and to reduce the semiconductor to metal phase transition temperature close to room temperature.     

A structural analysis of W-Sb mixed oxide catalyst

An investigation on the structure of W-Sb mixed oxide catalyst, W₁₂Sb_xO_y (x = 1, 3, 5), is proposed. The W-Sb mixed oxide powders were prepared by the calcination of aqueous precursors, antimony tartrate and ammoniummetatungstate, and characterized with scanning electron microscope, X-ray diffractometer, and transmission electron microscope. At low content of Sb (x = 1), the W-Sb mixed oxide powder consisted of polyhedral particles, and their crystal structure was triclinic WO₃. At higher content (x = 3, 5), majority of the oxide powders were bar-shaped particles, consisting of triclinic WO₃ and tetragonal WO₃. With electron diffraction pattern and simulation, Sb incorporation into the cuboctahedral sites of perovskite-like WO₃ was proved and its effect on the phase transition from triclinic to tetragonal was discussed.     

Microstructural and electrochromic properties of tungsten oxide thin films produced by surfactant mediated electrodeposition

By electrochemically controlling the structure of the surface aggregates, the grain microstructure has been optimized to yield mesoporous thin films of tungsten oxide (WO₃) at the electrode-electrolyte interface in a peroxotungstate sol in the presence of a structure-directing agent (Triton) at room temperature. Apart from the dominant ultrafine nanocrystallites and pores (5-10 nm), well-developed abutting grains (25-100 nm) and nanofibrils also constitute an integral part of the film matrix. X-ray photoemission spectra reveal the as-deposited film (WO_3−x) to be constituted by a high proportion of W⁶⁺ states with a low oxygen deficiency (x = 0.02). A relatively high W⁵⁺ content in the film, upon intercalation of 18 mC cm⁻² charge translates into a large coloring efficiency (η_VIS ∼ 70 cm² C⁻¹) and transmission modulation. At a lithium intercalation level of 22 mC cm⁻², in addition to W⁵⁺ and W⁶⁺ states, the film also comprises of W⁴⁺ states. The extremely fast color-bleach kinetics (3 and 2 s, respectively, for a 50% change in transmittance) shown by the as-deposited WO₃ film are repercussions of the mesopore morphology, the multiple nanostructures and the sixfold channels of its hexagonal modification. The film shows a high cycling stability as the switching times do not show any significant decline even after 3500 repetitive cycles. Coloration efficiency over the solar and photopic regions and current density for lithium intercalation for the as-deposited film are superior to that observed for the films annealed at 100, 250 and 500 °C. The abysmal electrochromic response of the annealed films is a consequence of surface defects like cracks and uncontrolled densification and pore shrinkage.     

Luminescence of ZnWO4 and CdWO4 thin films prepared by spray pyrolysis

Thin films of ZnWO₄ and CdWO₄ were prepared by spray pyrolysis and the structural, optical, and luminescence properties were investigated. Both ZnWO₄ and CdWO₄ thin films showed a broad blue-green emission band. The broad band of ZnWO₄ films was centered at 495 nm (2.51 eV) consisted of three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 540 nm (2.30 eV). The broad band of CdWO₄ films at 495 nm (2.51 eV) could be decomposed to three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 545 nm (2.28 eV). These results are consistent with emission from the WO₆⁶⁻ molecular complex. The luminance and efficiency for ZnWO₄ film at 5 kV and 57 μA/cm² were 48 cd/m² and 0.22 lm/w, respectively, and for CdWO₄ film the values were 420 cd/m² and 1.9 lm/w.     

Structural transition and blue emission in textured and highly transparent spray deposited Li doped WO3 thin films

The effect of Li (0-5 wt%) doping on the properties of WO₃ thin films deposited using an automated homemade spray pyrolysis unit is studied. Change in structural and optical properties is observed on doping with Li. The XRD patterns shows that undoped WO₃ film has an orthorhombic phase while the Li (1-5 wt%) doped WO₃ films have tetragonal phase. The SEM and AFM images confirm relatively smooth surface of Li doped WO₃ films compared to undoped WO₃ film. Transmission spectra reveal that the transparency of the Li-doped films is much greater than that of undoped film. From the transmission data, the direct, indirect bandgap and phonon energies were calculated. Room temperature photoluminescence spectra showed pronounced blue emission on doping with Li.     

Preparation of WO3 nanoparticles and application to NO2 sensor

WO₃ nanoparticles were prepared by evaporating tungsten filament under a low pressure of oxygen gas, namely, by a gas evaporation method. The crystal structure, morphology, and NO₂ gas sensing properties of WO₃ nanoparticles deposited under various oxygen pressures and annealed at different temperatures were investigated. The particles obtained were identified as monoclinic WO₃. The particle size increased with increasing oxygen pressure and with increasing annealing temperature. The sensitivity increased with decreasing particle size, irrespective of the oxygen pressure during deposition and annealing temperature. The highest sensitivity of 4700 to NO₂ at 1 ppm observed in this study was measured at a relatively low operating temperature of 50 °C; this sensitivity was observed for a sensor made of particles as small as 36 nm.     

Preparation and characterization of the amorphous tungsten cone field emitter arrays by Ar etching

Uniform amorphous tungsten cone arrays in high density were fabricated by Ar⁺ reduction etching of WO₃ nanowire film. The etching process was performed in the analysis chamber of an X-ray photoelectron spectroscopy (XPS) system. SEM and TEM results revealed that the tip radius of the etched cones was 10 nm, and the cones were amorphous with a high aspect ratio of over 250. XPS analysis proved the cones to be metallic tungsten. In the aspect of field-emission property, the tungsten cone arrays had a lower turn-on field of 3 MV m⁻¹ compared with 5 MV m⁻¹ of the as-grown original WO₃ nanowire film.     

Combustion synthesis and luminescence properties of NaY1−xEux(WO4)2 phosphors

The red phosphors NaY_1−xEu_x(WO₄)₂ with different concentrations of Eu³⁺ were synthesized via the combustion synthesis method. As a comparison, NaEu(WO₄)₂ was prepared by the solid-state reaction method. The phase composition and optical properties of as-synthesized samples were studied by X-ray powder diffraction and photoluminescence spectra. The results show that the red light emission intensity of the combustion synthesized samples under 394 nm excitation increases with increase in Eu³⁺ concentrations and calcination temperatures. Without Y ions doping, the emission spectra intensity of the NaEu(WO₄)₂ phosphor prepared by the combustion method fired at 900 °C is higher than that prepared by the solid-state reaction at 1100 °C. NaEu(WO₄)₂ phosphor synthesized by the combustion method at 1100 °C exhibits the strongest red emission under 394 nm excitation and appropriate CIE chromaticity coordinates (x=0.64, y=0.33) close to the NTSC standard value. Thus, its excellent luminescence properties make it a promising phosphor for near UV InGaN chip-based red-emitting LED application.     

Influence of annealing temperature on microstructure and optical properties of sol-gel derived tungsten oxide films

Tungsten oxide (WO₃) thin films have been extensively studied for their interesting physical properties and a variety of potential applications in electrochromic devices. In order to explore the possibility of using these in electrochromic devices, a preliminary and thorough study of the optical properties of the host materials is an important step. Based on this, the influence of annealing temperature on the structural, surface morphological, optical and electrochromic properties has been investigated in the present work. The host material, WO₃ films, has been prepared from an ethanolic acetylated peroxotungstic acid sol containing 5 wt.% oxalic acid dehydrate (OAD) by sol-gel technique. The monoclinic structure and textured nature change of the films with the temperature increasing have been investigated by X-ray diffraction analysis. The surface morphology evolution of the films has been characterized by SEM. The shift in absorption edge towards the higher wavelength region observed from optical studies may be due to the electron scattering effects and the optical band filling effect that reveals the crystallization of the film. The amorphous film shows better optical modulation (ΔT = 76.9% at λ = 610 nm), fast color-bleach kinetics (t_c ∼ 4 s and t_b ∼ 9 s) and good reversibility (Q_b/Q_c = 90%), thereby rendering it suitable for smart window applications.     

Investigation on spectral features of tungsten ions in PbO-Bi2O3-As2O3 glass matrix

Lead bismuth arsenate glasses mixed with different concentrations of WO₃ (ranging from 0 to 6.0 mol%) were synthesized. Differential thermal analysis (DTA), optical absorption, ESR and IR spectral studies have been carried out. The results of DTA have indicated that there is a gradual decrease in the resistance of the glass against devitrification with increase in the concentration of WO₃ upto 4.0 mol%.The optical absorption spectra of these glasses exhibited a relatively broad band peaking at about 880 nm identified due to d_xy→d_x²_−y² transition of W⁵⁺ ions; this band is observed to be more intense in the spectrum of glass containing 4.0 mol% of WO₃. Further, two prominent kinks attributed to ³P₀→¹S₀, ¹D₂ transitions of Bi³⁺ ions have also been located in the absorption spectra. The ESR spectra of these glasses recorded at room temperature exhibited an asymmetric signal at g_⊥∼1.71 and g_ll∼1.61. The intensity of the signal is observed to be maximal for the spectrum of the glass W₄. The quantitative analysis of optical absorption and ESR spectral studies have indicated that there is a maximum reduction of tungsten ions from W⁶⁺ state to W⁵⁺ state in the glass containing 4.0 mol% of WO₃. The IR spectral studies have indicated that there is a increasing degree of disorder in the glass network with increase in the concentration of WO₃ upto 4.0 mol%.     

Effect of citric acid on photoelectrochemical properties of tungsten trioxide films prepared by the polymeric precursor method

Effect of citric acid (CA) on microstructure and photoelectrochemical properties of WO₃ films prepared by the polymeric precursor method was investigated. The obtained materials were characterized by means of X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM). The results showed that samples prepared with adding different amounts of citric acid had a pure phase of cubic. The addition of citric acid could significantly increase the particle size and change the surface of WO₃ films. The photoelectrochemical measurements were performed using a standard three-electrode system cell. The films prepared from mass ratios of CA/PEG (R = 0, 0.2, 0.4, 0.6 and 1) showed 1.0, 1.4, 1.7, 2.1 and 0.9 mA cm⁻² at 1.2 V under illumination with a 500 W xenon lamp (I₀ = 100 mW/cm²), respectively.     

The influence of substrate temperature variation on tungsten oxide thin film growth in an HFCVD system

Tungsten oxide (WO₃) thin films were deposited by a modified hot filament chemical vapor deposition (HFCVD) technique using Si (1 0 0) substrates. The substrate temperature was varied from room temperature to 430 °C at an interval of 100 °C. The influence of the substrate temperature on the structural and optical properties of the WO₃ films was studied. X-ray diffraction and Raman spectra show that as substrate temperature increases the film tends to crystallize from the amorphous state and the surface roughness decreases sharply after 230 °C as confirmed from AFM image analysis. Also from the X-ray analysis it is evident that the substrate orientation plays a key role in growth. There is a sharp peak for samples on Si substrate due to texturing. The film thickness also decreases as substrate temperature increases. UV-vis spectra show that as substrate temperature increases the film property changes from metallic to insulating behavior due to changing stoichiometry, which was confirmed by XPS analysis.     

Structural, electrical and optical properties of TiO2 doped WO3 thin films

TiO₂ doped WO₃ thin films were deposited onto glass substrates and fluorine doped tin oxide (FTO) coated conducting glass substrates, maintained at 500 °C by pyrolytic decomposition of adequate precursor solution. Equimolar ammonium tungstate ((NH₄)₂WO₄) and titanyl acetyl acetonate (TiAcAc) solutions were mixed together at pH 9 in volume proportions and used as a precursor solution for the deposition of TiO₂ doped WO₃ thin films. Doping concentrations were varied between 4 and 38%. The effect of TiO₂ doping concentration on structural, electrical and optical properties of TiO₂ doped WO₃ thin films were studied. Values of room temperature electrical resistivity, thermoelectric power and band gap energy (E_g) were estimated. The films with 38% TiO₂ doping in WO₃ exhibited lowest resistivity, n-type electrical conductivity and improved electrochromic performance among all the samples. The values of thermoelectric power (TEP) were in the range of 23-56 μV/K and the direct band gap energy varied between 2.72 and 2.86 eV.     

Optical properties of Dy ions in sodium gadolinium tungstates crystal

Dy³⁺-doped NaGd(WO₄)₂ crystal with sizes of about Φ20×40 mm² was grown by the Czochralski technique along the (0 0 1) orientation. Polarized absorption spectra, fluorescence spectra, and fluorescence decay curve of Dy³⁺-doped NaGd(WO₄)₂ have been recorded at room temperature. Based on the Judd-Ofelt (J-O) theory, the intensity parameters from the measured line strengths were evaluated. The J-O parameters were used to predict radiative transition probabilities, radiative lifetimes and branching ratios for various excited levels of Dy³⁺-doped NaGd(WO₄)₂ crystal. The luminescent quantum efficiency of the ⁴F_9/2 level was determined to be approximately 63% for this material. The emission cross-section of the ⁴F_9/2→⁶H_13/2 transition was estimated by using the Füchtbauer-Ladengurg method.     

Effect of WO3 on structural and optical properties of CeO2-PbO-B2O3 glasses

Pure and WO₃ doped CeO₂-PbO-B₂O₃ glasses are prepared by the melt-quench technique. The structural and optical analyses of glasses are carried out by XRD, FTIR, density and UV-vis spectroscopic measurement techniques. FTIR analysis indicates the transformation of structural units of BO₃ into BO₄ with W-O-W vibration and the presence of WO₄ and WO₆ units observed with increase in WO₃ contents. Decrease in band gap for CeO₂-PbO-B₂O₃ glasses from 2.89 to 2.30 eV and for WO₃ doped glasses from 2.89 to 1.95 eV has been observed and discussed. This decrease in band gap with WO₃ doping approaches to semiconductor behavior. It shows that the presence of WO₃ in the glass samples causes more compaction of the borate network due to the formation of BO₄ groups and the presence of WO₄ and WO₆ groups, which result in a decrease in the optical band gap energy and increase in the density.     

Blue luminescence in Tm-doped KGd(WO4)2 single crystals

Up-conversion blue emissions of trivalent thulium ions in monoclinic KGd(WO₄)₂ single crystals at 454 and 479 nm are reported for a single pump laser source at 688 nm. We grew thulium-doped KGd(WO₄)₂ single crystals at several concentrations from 0.1% to 10%. We recorded a polarized optical absorption spectrum for the ³F₂+³F₃ energy levels of thulium at room temperature and low temperature (6 K). From the low temperature emission spectra we determined the splitting of the ³H₆ ground state. The blue emissions are characterized as a function of the dopant concentration and temperature from 10 K to room temperature. To our knowledge, this is the first time that sequential two-photon excitation process (STEP) generated blue emissions in thulium-doped single crystals with a single excitation wavelength.     

Structural characterization of La0.9Ba0.1MnO3/Y-ZrO2 film by X-ray diffraction

Perovskite manganite La_0.9Ba_0.1MnO₃(LBMO) films were deposited on (0 0 1)-oriented single crystal yttria-stabilized zirconia (YSZ) substrate by 90° off-axis radio frequency magnetron sputtering. The film thickness ranged from 10 nm to 100 nm. Grazing incidence X-ray diffraction technique and high resolution X-ray diffraction were applied to characterize the structure of LBMO films. The LBMO film mainly consisted of (0 0 1)-orientated grain as well as weakly textured (1 1 0)-orientated grain. The results indicated that an amorphous layer with thickness of about 4 nm was formed at the LBMO/YSZ interface. The strain in LBMO film was small and averaged to be about -0.14%. The strain in the film was not lattice mismatch-induced strain but residual strain due to the difference in thermal expansion coefficient between film and substrate.     

Effect of crystallinity of Co layer on perpendicular exchange bias in Au-capped ultrathin Co film on Cr2O3(0 0 0 1) thin film

The effect of the crystalline quality of ultrathin Co films on perpendicular exchange bias (PEB) has been investigated using a Au/Co/Au/α-Cr₂O₃ thin film grown on a Ag-buffered Si(1 1 1) substrate. Our investigation is based on the effect of the Au spacer layer on the crystalline quality of the Co layer and the resultant changes in PEB. An α-Cr₂O₃(0 0 0 1)layer is fabricated by the thermal oxidization of a Cr(1 1 0) thin film. The structural properties of the α-Cr₂O₃(0 0 0 1) layer including the cross-sectional structure, lattice parameters, and valence state have been investigated. The fabricated α-Cr₂O₃(0 0 0 1) layer contains twin domains and has slightly smaller lattice parametersthan those of bulk-Cr₂O₃. The valence state of the Cr₂O₃(0 0 0 1) layer is similar to that of bulk Cr₂O₃. The ultrathin Co film directly grown on the α-Cr₂O₃(0 0 0 1) deposited by an e-beam evaporator is polycrystalline. The insertion of a Au spacer layer with a thickness below 0.5 nm improves the crystalline quality of Co, probably resulting in hcp-Co(0 0 0 1). Perpendicular magnetic anisotropy (PMA) appears below the Néel temperature of Cr₂O₃ for all the investigated films. Although the PMA appears independently of the crystallinequality of Co, PEB is affected by the crystalline quality of Co. For the polycrystalline Co film, PEB is low, however, a high PEB is observed for the Co films whose in-plane atom arrangement is identical to that of Cr³⁺ in Cr₂O₃(0 0 0 1). The results are qualitatively discussed on the basis of the direct exchange coupling between Cr and Co at the interface as the dominant coupling mechanism.     

Formation of ⊥c texture of tungsten disulfide thin films with nickel

The formation of ⊥c texture of WS₂ thin films by solid state reaction between the spray deposited WO₃ and gaseous sulfur vapours with Ni interfacial layer has been reported. X-ray diffraction technique has been used to measure the degree of preferred orientation and texture of WS₂ films. Scanning electron microscopy, transmission electron microscopy and atomic force microscopy have been used to characterize the microstructure and morphology. The electronic structure and chemical composition was studied using X-ray photoelectron spectroscopy. The WS₂ films comprise single crystalline quality hexagonal crystallites of 15 μm × 15 μm size with their basal planes parallel to the substrate. The film consists of turbostratic stacking sequence of 2H and 3R polytypes of WS₂. The tungsten-to-sulfur ratio was estimated to be 1:1.8. The various qualitative models used to explain promotional effects are briefly outlined and the plausible underlying mechanism of formation of ⊥c texture with nickel, in this study, is given.