An efficient route towards the covalent functionalization of single walled carbon nanotubes

A simple and efficient method of chemical functionalization of both single and multiwalled carbon nanotubes has been discussed to give enhanced water solubility by rapidly and efficiently generating an appreciable amount of hydrophilic functional groups using microwave radiation. Surface functionalization containing more than 30 wt% of oxygen has been achieved, resulting into solubility of 2–5 mg/mL. Further covalent functionalization of such soluble SWNTs provides a remarkable degree of aniline functionalization through amidation, where the formation of polyaniline has been avoided. Functionalization of SWNTs is confirmed by techniques like electron microscopy, Fourier transform infrared spectroscopy, thermogravimetry, Raman spectroscopy, cyclic voltammetry and impedance spectroscopy. Electrochemical analysis suggests an enhanced double layer capacitance (110 F/g) of nanotubes after microwave treatment. Aniline functionalization of SWNTs shows possible variations on the nanotube topography with concomitant formation of a dynamic polymer layer on the nanotube surface.     

Fabrication and characterization of suspended single-walled carbon nanotubes

Suspended single-walled carbon nanotubes (SWCNTs) between SiO₂ pillars via a direct lithographic route using a simple mixture of catalyst precursor [Co(III) acetylacetonate, Co(acac)₃] and conventional electron beam resist (ma-N2403) were fabricated. The catalytic electron beam resist (Cat-ER) layer plays dual roles as a catalyst and a resist layer for the growth and alignment of CNTs, respectively. The structure of the grown nanotube was characterized by Raman spectroscopy (633 nm laser excitation). Nanotubes grown from Cat-ER with Co(acac)₃ show the typical Raman spectra of SWCNTs which are characterized by the strong tangential bands near to 1590 cm⁻¹ and radial breathing modes (RBMs) in the low frequency region (<300 cm⁻¹). The calculated diameter of the probed nanotubes individually corresponds to the range 0.86-1.77 nm.     

Comparative study on modification of single wall carbon nanotubes by sodium dodecylbenzene sulfonate and melamine sulfonate superplasticiser

In this work, the results of synthesis and characterization of single wall carbon nanotubes (SWCNTs) functionalized by two surfactants (sodium dodecylbenzene sulfonate and melamine sulfonate superplasticiser) have been presented. The properties of pristine and modified SWCNTs have been compared by different techniques: Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM). Raman analysis reveals the changes in vibrational spectra of SWCNTs after modification by different surfactant molecules. FTIR analysis has shown the presence of sulfonate group which is strong evidence for nanotube modification. AFM analysis has shown separation of big single wall carbon nanotube bundles into thin bundles of them.     

Deposition of silver nanoparticles on carbon nanotube by chemical reduction method: Evaluation of surface,thermal and optical properties

Silver was stabilized on multi-walled carbon nanotubes (MWCNTs) by chemical-reduction technique using N,N-dimethylformamide (DMF) as a reducing agent. The influence of silver on the performance of carbon nanotubes (CNTs) was investigated by employing Fourier-transform infrared spectra (FTIR), Raman spectroscopy (RAS), thermal gravimetric analysis (TGA), zeta potential measurement, scanning electron microscope (SEM), electron dispersive X-ray spectrometer (EDX), transmission electron microscopy (TEM), and reflectance spectroscopy (RS). FTIR as well as RS methods evidenced the synthesis procedure using chemical reduction method was successful. Performing TGA of the samples under oxygen atmosphere demonstrated that the silver nanoparticles (Ag NPs) generated on MWCNTs surface can decrease the thermal stability of the particles by the catalytic oxidation of CNTs. In contrary, the thermal stability of the MWCNTs has improved under nitrogen atmosphere. EDX results showed the presence of Ag, Au and Co on the surface of deposited sample. The synthesised silver multi-walled carbon nanotubes (Ag–MWCNTs) were found to have higher UV reflection activity compared with untreated particles. The Ag–CNTs can be used in producing anti-UV composites.     

The use of calcination in exposing the entrapped Fe particles from multi-walled carbon nanotubes grown by chemical vapour deposition

Multi-walled carbon nanotubes (MWCNTs) were synthesized a by chemical vapour deposition method. The effect of calcination at temperatures ranging from 300 to 550°C in exposing the metal nanoparticles within the nanotube bundles was studied. The degree of degradation of the structural integrity of the MWCNTs during the thermal process was studied by Raman spectroscopy, X-ray diffraction analysis, field-emission scanning electron microscopy, and transmission electron microscopy. The thermal behaviour of the as-prepared and calcined samples was investigated by thermogravimetric analysis. Calcination in air, at 400°C for 1 h, was found to be an efficient and simple method to extract metallic impurities from the amorphous carbon shells with minimal damage to the tube walls and lengths. The nanotubes were observed to be damaged at temperatures higher than 450°C.     

Production and characterization of polymer nanocomposite with aligned single wall carbon nanotubes

We reported a simple method to fabricate polymer nanocomposites with single-walled carbon nanotubes (SWNTs) having exceptional alignment and improved mechanical properties. The composite films were fabricated by casting a suspension of single walled carbon nanotubes in a solution of thermoplastic polyurethane and tetrahydrofuran. The orientation as well as dispersion of nanotubes was determined by scanning electron microscopy, transmission electron microscopy and polarized Raman spectroscopy. The macroscopic alignment probably results from solvent-polymer interaction induced orientation of soft segment chain during swelling and moisture curing. The tensile behavior of the aligned nanotube composite film was also studied. At a 0.5 wt.% nanotube loading, a 1.9-fold increase in Young's modulus was achieved.     

Functionalization of carbon nanotubes with silver clusters

In this paper, an advanced method of one-step functionalization of single and multi walled carbon nanotubes (SWCNTs and MWCNTs) using γ-irradiation was described. Two synthesis procedures, related with different reduction species, were employed. For the first time, poly(vinyl alcohol) PVA is successfully utilized as a source to reduce silver (Ag) metal ions without having any additional reducing agents to obtain Ag nanoparticles on CNTs. The decoration of carbon nanotubes with Ag nanoparticles takes place through anchoring of (PVA) on nanotube's surface. Optical properties of as-prepared samples and mechanism responsible for the functionalization of carbon nanotubes were investigated using UV-vis and FTIR spectroscopy, respectively. Decorated carbon nanotubes were visualized using microscopic techniques: transmission electron microscopy and scanning tunneling microscopy. Also, the presence of Ag on the nanotubes was confirmed using energy dispersive X-ray spectroscopy. This simple and effective method of making a carbon nanotube type of composites is of interest not only for an application in various areas of technology and biology, but for investigation of the potential of radiation technology for nanoengineering of materials.     

Optimum degree of functionalization for carbon nanotubes

Covalent functionalizations, especially oxidization and derivative functionalization, significantly improve the surface characteristics of carbon nanotubes, but also bring undesired devastation of sidewalls. This paper presents a theoretic model to investigate double-edge effects of covalent functionalization on carbon nanotubes for the polymer composite application. An optimal degree of functionalization is proposed and calculated based on the trade-off of required load-transfer and induced devastation of nanotube sidewalls. The negative effect on elastic modulus is also calculated. For oxidization-based functionalization of originally defect-free nanotubes, the calculation results indicate that about 10% functionalization degree is suggested to be optimum for the balance of efficient load-transfer and conspicuous devastation from the highly covalent functionalization. The original defects in nanotube surface also reduce the optimum functionalization degree and the reduction is dependent on the original defect concentration. The computational results indicate that nanotube diameter and percentages in the polymer composites show considerably effect on the optimum functionalization degree. Carbon nanotubes with smaller diameter show lower optimum functionalization degree. Increasing percentage of carbon nanotubes in the polymer composites also leads to lower optimum functionalization degree.     

Phonons in carbon nanotubes

A broad review of the unusual one-dimensional properties of phonons in carbon nanotubes is presented, including phonons in isolated nanotubes and in crystalline arrays of nanotubes in nanotube bundles. The main technique for probing the phonon spectra has been Raman spectroscopy and the many unique and unusual features of the Raman spectra of carbon nanotubes are reviewed. Also included is a brief review of the thermal properties of carbon nanotubes in relation to their unusual phonon dispersion relations and density of states.     

Effect of different microwave-based treatments on multi-walled carbon nanotubes

Three new methods for the functionalization of multi-walled carbon nanotubes (MWCNTs) are reported using microwave (MW) energy and water as a mild chemical agent. In the first method we reported the effect of MW irradiation on a dispersion of MWCNTs in deionized water, in the second method we studied the exposing of MWCNT to microwave irradiation in the presence of steam, and in the third method we used microwave oven-generated plasma for the functionalization of MWCNTs. We also performed thermal oxidation and acid treatment as two conventional methods for oxidative functionalization of carbon nanotubes, to compare their effect with our results. Transmission electron microscopy (TEM) and Raman spectroscopy results showed that although these microwave methods introduced some defects to the carbon nanotubes, the damage was less severe than conventional treatments. X-ray photoelectron spectroscopy (XPS) measurements confirmed that the functionalization of carbon nanotubes by these methods favored hydroxyl groups, which are useful when further functionalization is required.     

Optical properties of fullerene and non-fullerene peapods

Single-wall carbon nanotubes (SWNTs) encapsulating fullerenes, so-called fullerene peapods, were synthesized in high yield by using diameter-selected nanotubes as pods. Transmission electron microscopy revealed high-density fullerene chains inside the nanotubes. X-ray-diffraction measurements indicate 85% filling for C₆₀ and 72% filling for C₇₀ molecules as a total yield. Interestingly, C₆₀ peas do not show any thermal expansion while C₇₀ peas show normal behavior. Room-temperature Raman spectra show one-dimensional photopolymerization of C₆₀ inside nanotubes by blue-laser irradiation, suggesting molecular rotation inside them. In C₇₀ peapods, no photopolymerization was observed but the relative Raman intensity of each peak is different from the C₇₀ 3D crystal. This is probably caused by mixing of two different crystal structures in C₇₀ peas. Furthermore, we synthesized Zn-diphenylporphyrin peapods. Optical absorption and Raman spectra suggest that the encapsulated molecules are deformed by interaction with the SWNT. Received: 12 November 2001 / Accepted: 3 December 2001 / Published online: 4 March 2002     

Resonant Raman spectroscopy and spectroelectrochemistry characterization of carbon nanotubes/polyaniline thin film obtained through interfacial polymerization

Thin, transparent, and self‐assembled films of neat polyaniline and polyaniline/carbon nanotube nanocomposites were deposited over glass substrates by interfacial polymerization. The effect of the carbon nanotubes on the structure and conformation of the polyaniline, and the type of interaction between the polymer and the nanotubes, have been studied by resonant Raman spectroscopy and UV–Vis and Raman spectroelectrochemistry. The results indicate clearly that the carbon nanotubes induce important changes in the electronic structure of the polymer, resulting in a more polaronic organization. Additionally, an effective interaction between the polymer and the nanotube, based on a polyaniline‐to‐nanotube charge transfer, is proposed in this work. Copyright © 2012 John Wiley & Sons, Ltd.     

The effect of a large SWNT diameter distribution on cesium intercalation

Vapor-phase intercalation of a single-walled carbon nanotube sample with Cs was carried out and monitored in situ by Raman spectroscopy. Results indicate that the endpoint of the intercalation was limited by small interstitial gaps in the nanotube bundles. These small-diameter gaps are present because of the significant number of small-diameter nanotubes (0.9-1.0 nm, as calculated from Raman radial breathing mode frequencies) present in the sample. It is not possible to determine from our Raman spectra whether the early endpoint is the result of diffusion limitation or the equilibrium energetics at the endpoint, although some diffusion limitation is observed near the beginning of the reaction. A simple geometric model for expansion of the nanotube bundles under intercalation is presented; this model reproduces, reasonably well, measured expansions reported by others and explains both diffusion- and equilibrium-limited mechanisms in terms of the larger lattice expansion required for smaller-diameter nanotubes. Staging of the intercalation process, in analogy with the staged intercalation of graphite intercalation compounds, is not observed. Instead, the transverse mode peaks undergo a gradual decrease in intensity and a gradual charge transfer- and electronic coupling-induced downshift.     

Comparison of metallic silver and copper doping effects on single-walled carbon nanotubes

In this work we performed the filling of single-walled carbon nanotube channels with metallic silver and copper by means of two-step synthesis including imbuing with metal nitrate aqueous solution and further annealing. It has been shown that metal insertion into the nanotube cavities results in the Fermi level upshift and the charge transfer from metal to carbon atoms, thus donor doping of single-walled carbon nanotubes takes place. At the same time, encapsulated silver has a larger donor effect on the carbon nanotubes that has been proved by Raman spectroscopy and X-ray photoelectron spectroscopy.     

170keV质子辐照对多壁碳纳米管薄膜微观结构与导电性能的影响

碳纳米管具有优异的导电性, 是未来电子元器件的理想候选材料, 应用前景广阔. 针对碳纳米管在空间电子元器件的应用需求, 本文研究了170 keV质子辐照对多壁碳纳米管薄膜微观结构与导电性能的影响. 采用扫描电子显微镜(SEM)、拉曼光谱仪(Raman)、X射线光电子能谱仪(XPS)及电子顺磁共振谱仪(EPR)对辐照前后碳纳米管试样的表面形貌和微观结构进行分析; 利用四探针测试仪对碳纳米管薄膜进行导电性能分析. SEM分析表明, 170 keV质子辐照条件下, 当辐照注量高于5×10¹⁵ p/cm² (protons/cm²)时, 碳纳米管薄膜表面变得粗糙疏松, 纳米管发生明显弯曲、收缩及相互缠结现象. 目前, 质子辐照纳米管发生的收缩现象被首次发现. 基于Raman和XPS分析表明, 170 keV质子辐照后碳纳米管的有序结构得到改善, 且随辐照注量增加, 碳纳米管的有序结构改善明显. 结构的改善主要是由于170 keV质子辐照碳纳米管所产生的位移效应导致缺陷重组. EPR分析表明, 随着辐照注量的增加, 碳纳米管薄膜内的非局域化电子减少. 利用四探针测试分析表明, 碳纳米管薄膜的导电性能变差, 这是由于170 keV质子辐照导致碳纳米管薄膜中的电子特性及形态发生改变. 本文研究结果有助于利用质子辐照对碳纳米管膜结构和性能进行调整, 从而制备出抗辐射的纳米电子器件.     

Electron diffraction on graphite nanocrystals in the walls of carbon nanotubes

The structure and defects in the walls and cavities of carbon nanotubes were examined by electron diffraction, transmission electron microscopy, energy dispersive X-ray analysis and Raman spectroscopy. The predominating defects in the walls of the nanotubes are graphite nanocrystals having a preferential orientation in the direction of the nanotube axis, and another significant type of defects are particles of the catalyst in the nanotube cavities. In the cavities, also the presence of molybdenum was proved having its origin in the catalyst.     

Hydrogen-free spray pyrolysis chemical vapor deposition method for the carbon nanotube growth: Parametric studies

Spray pyrolysis chemical vapor deposition (CVD) in the absence of hydrogen at low carrier gas flow rates has been used for the growth of carbon nanotubes (CNTs). A parametric study of the carbon nanotube growth has been conducted by optimizing various parameters such as temperature, injection speed, precursor volume, and catalyst concentration. Experimental observations and characterizations reveal that the growth rate, size and quality of the carbon nanotubes are significantly dependent on the reaction parameters. Scanning electron microscopy, transmission electron microscopy, and Raman spectroscopy techniques were employed to characterize the morphology, structure and crystallinity of the carbon nanotubes. The synthesis process can be applied to both semiconducting silicon wafer and conducting substrates such as carbon microfibers and stainless steel plates. This approach promises great potential in building various nanodevices with different electron conducting requirements. In addition, the absence of hydrogen as a carrier gas and the relatively low synthesis temperature (typically 750 °C) qualify the spray pyrolysis CVD method as a safe and easy way to scale up the CNT growth, which is applicable in industrial production.     

High pressure Raman spectroscopy of single-walled carbon nanotubes: Effect of chemical environment on individual nanotubes and the nanotube bundle

The pressure-induced tangential mode Raman peak shifts for single-walled carbon nanotubes (SWNTs) have been studied using a variety of different solvents as hydrostatic pressure-transmitting media. The variation in the nanotube response to hydrostatic pressure with different pressure transmitting media is evidence that the common solvents used are able to penetrate the interstitial spaces in the nanotube bundle. With hexane, we find the surprising result that the individual nanotubes appear unaffected by hydrostatic pressures (i.e. a flat Raman response) up to 0.7 GPa. Qualitatively similar results have been obtained with butanol. Following the approach of Amer et al. [J. Chem. Phys. 121 (2004) 2752], we speculate that this is due to the inability of SWNTs to adsorb some solvents onto their surface at lower pressures. We also find that the role of cohesive energy density in the solvent-nanotube interaction is more complex than previously thought.     

Novel approach to tailoring the electronic properties of single-walled carbon nanotubes by the encapsulation of high-melting gallium selenide using a single-step process

A single-step method of filling the channels of single-walled carbon nanotubes with the melt of refractory GaSe is proposed and successfully implemented. The filled nanotubes are investigated by optical absorption spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. It is found that charge transfer from the nanotube walls to embedded GaSe accompanied by lowering of the Fermi level in nanotubes occurs in the obtained nanocomposite; i.e., acceptor doping of nanotubes takes place.     

Comparison of modification of electronic properties of single-walled carbon nanotubes filled with metal halogenide, chalcogenide, and pure metal

In present work, thulium chloride, gallium selenide, bismuth telluride, and silver were encapsulated into the channels of single-walled carbon nanotubes (SWCNTs). The structural properties of obtained nanostructures were studied by high-resolution transmission electron microscopy, and the modification of electronic properties of nanotubes as result of filling their channels with chosen substances was investigated by Raman spectroscopy and X-ray photoelectron spectroscopy. It was shown that the electronic properties of filled SWCNTs depend on the chemical nature of incorporated materials. The encapsulation of TmCl₃ and GaSe into the carbon nanotube channels leads to acceptor doping of the SWCNTs, and this effect is more prominent for thulium chloride. The incorporation of bismuth telluride into the nanotube cavities does not result in any modification of their electronic properties. The filling of the nanotube channels with silver leads to donor doping of the single-walled carbon nanotubes.