Principal energy band gaps of the quaternary alloy AlxGa1−xSbyAs1−y

The correlated function expansion (CFE) interpolation procedure was presented to efficiently estimate principal energy band gaps and lattice constants of the quaternary alloy Al_xGa_1−xSb_yAs_1−y over the entire composition variable space. The lattice matching conditions between x and y for the alloy Al_xGa_1−xSb_yAs_1−y substrated to InAs and GaSb were obtained by optimizing the alloy lattice constant to that of the substrates. The corresponding principal band gaps (E(Γ), E(L), and E(X)) were also calculated along the lattice matching condition on each substrate (InAs and GaSb).     

Dependence of electronic properties on nitrogen concentration in GaAs1−xNx dilute alloys

Based on the pseudopotential scheme, the effect of nitrogen concentration on electronic properties of zinc-blende GaAs_1−xN_x alloys has been investigated for small amounts of N. The agreement between our calculated electronic band parameters and the available experimental data is generally reasonable. In agreement with recent experiment, we find that the incorporation of a few percent of N in the material of interest reduces substantially the fundamental band-gap energy and narrows the full valence band width. The electron and heavy hole effective masses are found to decrease rapidly when adding a concentration of nitrogen less than 0.005 in GaAs. This may increase the mobility of electrons and heavy holes providing new opportunities regarding the transport properties. The information derived from the present study shows that GaAs_1−xN_x (0?x?0.05) properties may have an important optoelectronic applications in infrared and mid-infrared spectral regions.     

Electronic and structural properties of zincblende AlxIn1−xN

Numerical calculations based on first-principles are applied to study the electronic and structural properties of ternary zincblende AlInN alloy. The results indicate the lattice constant has a small deviation from the Vegard’s law. The direct and indirect bowing parameters of 4.731 ± 0.794 eV and 0.462 ± 0.285 eV are obtained, respectively, and there is a direct-indirect crossover near the aluminum composition of 0.817. The bulk modulus is monotonically increased with an increase of the aluminum composition, and the deviation parameter of bulk modulus of 10.34 ± 9.37 GPa is obtained. On the contrary, the pressure derivative of bulk modulus is monotonically decreased with an increase of the aluminum composition.     

Electronic structure of GaAs1−xNx under pressure

The electronic band structures of GaAs_1−xN_x for x=0.009, 0.016, 0.031 and 0.062 are calculated ab initio using a supercell approach in connection with the full-potential linear muffin-tin orbital method. Corrections for the ‘LDA gap errors’ are made by adding external potentials which are adjusted to yield correct gaps in pure GaAs. Even small amounts of nitrogen modify significantly the conduction bands, which become strongly non-parabolic. The effective mass in the lowest conduction band thus exhibits strong k-vector dependence. Calculated variations of gaps and effective masses with x and externally applied pressure are presented and compared to a variety of experimental data. There are significant error bars on our results due to the use of the supercell approach. These are estimated by examining the effects of varying the geometrical arrangement of the N-atoms substituting As. However, the calculations show that the electron mass for x>0.009 is much larger than that of pure GaAs, and that it decreases with x.     

Structural and optical properties of a-Si1−xCx:H films synthesized by dc magnetron sputtering technique

Hydrogenated amorphous SiC films (a-Si_1−xC_x:H) were prepared by dc magnetron sputtering technique on p-type Si(1 0 0) and corning 9075 substrates at low temperature, by using 32 sprigs of silicon carbide (6H-SiC). The deposited a-Si_1−xC_x:H film was realized under a mixture of argon and hydrogen gases. The a-Si_1−xC_x:H films have been investigated by scanning electronic microscopy equipped with an EDS system (SEM-EDS), X-ray diffraction (XRD), secondary ions mass spectrometry (SIMS), Fourier transform infrared spectroscopy (FTIR), UV-vis-IR spectrophotometry, and photoluminescence (PL). XRD results showed that the deposited film was amorphous with a structure as a-Si_0.80C_0.20:H corresponding to 20 at.% carbon. The photoluminescence response of the samples was observed in the visible range at room temperature with two peaks centred at 463 nm (2.68 eV) and 542 nm (2.29 eV). In addition, the dependence of photoluminescence behaviour on film thickness for a certain carbon composition in hydrogenated amorphous SiC films (a-Si_1−xC_x:H) has been investigated.     

Structural and magnetic properties of Cr1+x(Se1−yTey)2 compounds

The structural and magnetic properties of Cr_1+x(Se_1−yTe_y)₂ having a NiAs structure has been studied for (1+x)=1.27, 1.32 and 1.36 and y=0.75 by means of the Korringa-Kohn-Rostoker (KKR) band structure method. The sub-stoichiometry and the disorder on the chalcogenide sub-lattice has been treated by means of the coherent potential approximation (CPA) alloy theory. From total energy calculations a preferential site occupation on the Cr sub-lattice was found together with an antiparallel alignment of the magnetic moments on the two inequivalent Cr layers. The magnetic properties at finite temperature has been studied by means of Monte Carlo simulations on the basis of a classical Heisenberg Hamiltonian and the exchange coupling parameters calculated from first principles. This approach allowed to determine the critical temperature in good agreement with experiment.     

Atomistic computer simulation studies of La1−xSrxVO3

Static computer simulation techniques have been employed for structural investigation of the La_1−xSr_xVO₃ series. Potential parameters for V³⁺-O²⁻ and V⁴⁺-O²⁻ have been derived which reproduces the crystal structures of end members with sufficient accuracy. Variations of lattice parameters and bond distances with Sr concentration have been studied. The calculated lattice parameters decrease with increase in the Sr concentration. A structural phase transition from orthorhombic to cubic is observed at 50% Sr doping level.     

Electronic properties and elastic constants of wurtzite, zinc-blende and rocksalt AlN

Electronic properties and elastic constants of AlN in the wurtzite, zinc-blende and rocksalt structures are investigated using an ab initio pseudopotential method based on the density-functional theory with both the local-density approximation and the generalized gradient approximation for the exchange-correlation functional. The numerically calculated results compare well with the existing experimental data. For elastic constants of rocksalt AlN our results are predictions.     

Structural phase transition of boron nitride compound

The full-potential band-structure scheme based on the linear combination of overlapping nonorthogonal local-orbital (FPLO) is used. The crystal potential and density are represented as a lattice sum of local overlapping nonspherical contributions. The energetic transitions of BN of zinc-blende and wurtzite structures are calculated using the band structure scheme. The energy gap at ambient pressure is found to be indirect for the two structures. The structural properties of two structures of BN are (obtained from the total energy calculations) and the total density of states are calculated. The phase transition parameter of BN is investigated. The ionicity character of BN has been calculated to test the validity of our recent models. The results are in reasonable agreement with experimental and other theoretical results.     

Bulk Sn1−xMnxO2 magnetic semiconductors without room-temperature ferromagnetism

Polycrystalline Sn_1−xMn_xO₂ (0≤x≤0.05) diluted magnetic semiconductors were prepared by solid-state reaction method and their structural and magnetic properties had been investigated systematically. The three Mn-doped samples (x=0.01, 0.03, 0.05) undergo paramagnetic to ferromagnetic phase transitions upon cooling, but their Curie temperatures are far lower than room temperature. The magnetization cannot be attributed to any identified impurity phase. It is also found that the magnetization increases with increasing Mn doping, while the ratio of the Mn ions contributing to ferromagnetic ordering to the total Mn ions decreases.     

Tight-binding calculation of the optical conductivity in NaxCoO2

Optical conductivity in Na_xCoO₂ is calculated with tight binding approximation. The calculated gross features agree with the experimental findings. Interband transitions between nearly degenerate t_2g bands bring about absorption in the mid-infrared and near infrared regions. Structures observed at higher energies are also quite well reproduced with the present calculation. Possible effects of electron correlation are also briefly discussed.     

EPR and magnetic properties of vapour phase grown Zn1−xCrxTe crystals

The EPR and magnetic properties were investigated on vapour phase grown Zn_1−xCr_xTe (0.001?x?0.005) crystal samples at room temperature. The EPR spectra were observed for samples with x=0.001, 0.002 only. The simulations of the spectra confirm Cr³⁺ charge state of the dopant ion at tetrahedral symmetry. The magnetic behaviour of the samples with x=0.001 and 0.002 is neither that of Brillouin paramagnets nor Van Vleck systems while the samples with compositions x=0.003, 0.004 and 0.005 exhibited hysteresis behaviour.     

Effects of compositional phase transitions on luminescence of Sr1−xCaxTiO3:Pr

The mixed-compound of Sr_1−xCa_xTiO₃ has shown several compositional phase transformations. Photoluminescence and excitation spectra of the samples with different x and doped with 0.2% Pr³⁺ were investigated. Changes in the emission spectra were observed in different phases. The blue emission at 491 nm from ³P₀ state was found quite strong in the tetragonal phase, and was thermally quenched in the orthorhombic phases. The intensity of the red luminescence from ¹D₂ increases with increasing content of calcium. The strongest red emission is obtained from CaTiO₃:Pr³⁺. The results are discussed based on the configuration coordinate model and interaction of Pr with the charge transfer exciton state of the Ti complex.     

Metastable ferromagnetic phases with predictable Tcs in La2MnCo1−xNixO6

Metastable ferromagnetic phases, for different compositions in La₂MnCo_1−xNi_xO₆, are obtained for samples synthesized by a low-temperature method and annealed in air at different temperatures in the range 200-1350 °C. The T_cs of the ferromagnetic phases vary linearly between those of the phases of the end members. T_cs of the different phases of La₂MnCo_1−xNi_xO₆ can be predicted based on the T_cs and spin states of Mn, Co and Ni in the different phases of the end members, La₂MnCoO₆ and La₂MnNiO₆.     

Magnetic disorder induced enhanced magneto-resistance in La0.5Sr0.5Co1−xRuxO3

We observe a sharp increase in negative magneto-resistance ratio up to 40% for x=0.1, in La_0.5Sr_0.5Co_1−xRu_xO₃ which is due to the magnetic disorder induced by an anti-ferromagnetic interaction between Co and Ru ions. We also observe a metal to insulator and a ferromagnetic to anti-ferromagnetic transition for 0≤x≤0.3. Ruthenium (IV) ion disrupts an intermediate spin state of cobalt (Co³⁺:t_2g⁵e_g¹), forcing a double exchange mediated ferromagnetic state to an anti-ferromagnetic spin state for x≥0.2.     

Effect of applied bias voltage on corrosion-resistance for TiC1−xNx and Ti1−xNbxC1−yNy coatings

Corrosion-resistance behavior of titanium carbon nitride (Ti-C-N) and titanium niobium carbon nitride (Ti-Nb-C-N) coatings deposited onto Si(1 0 0) and AISI 4140 steel substrates via r.f. magnetron sputtering process was analyzed. The coatings in contact with a solution of sodium chloride at 3.5% were studied by Tafel polarization curves and impedance spectroscopy methods (EIS). Variations of the bias voltage were carried out for each series of deposition to observe the influence of this parameter upon the electrochemical properties of the coatings. The introduction of Nb in the ternary Ti-C-N film was evaluated via X-ray diffraction (XRD) analysis. The structure was characterized by using Raman spectroscopy to identify ternary and quaternary compounds. Surface corrosion processes were characterized using optical microscopy and scanning electron microscopy (SEM). XRD results show conformation of the quaternary phase, change in the strain of the film, and lattice parameter as the effect of the Nb inclusion. The main Raman bands were assigned to interstitial phases and “impurities” of the coatings. Changes in Raman intensities were attributed to the incorporation of niobium in the Ti-C-N structure and possibly to resonance enhancement. Finally, the corrosion data obtained for Ti-C-N were compared with the results of corrosion tests of Ti-Nb-C-N coating. The results obtained showed that the incorporation of niobium to Ti-C-N coatings led to an increase in the corrosion-resistance. On another hand, an increase in the bias voltage led to a decrease in the corrosion-resistance for both Ti-C-N and Ti-Nb-C-N coatings.     

Observation of new critical point in InxAl1−xAs alloy using spectroscopic ellipsometry

Using a spectroscopic ellipsometry, pseudodielectric functions 〈?〉 of In_xAl_1−xAs ternary alloy films (x = 0.43, 0.62, 0.75, and 1.00) from 0.74 to 6.48 eV were determined. Fast in-situ chemical etching to effectively remove surface overlayers using charge-coupled device detector and to avoid the reoxidation of the surface of films prior to the ellipsometric spectrum measurement was performed. At the high energy region, an additional critical point structure which is interpreted as the E′₁ transition from the band structure calculation of the linear augmented Slater-type orbital method was reported.     

First-principles study on the metallic antiferromagnet Co[PhPO3]·H2O

The electronic structure and the magnetic properties of transition metal phosphonate Co(PhPO₃)·H₂O have been studied by first-principles within the density-functional theory (DFT) and the full potential linearized augmented plane wave (FP-LAPW) method. The total energy, the total magnetic moment, the atomic spin magnetic moments and the density of states(DOS) of Co(PhPO₃)·H₂O were all calculated. The calculations reveal that the title compound is a metallic antiferromagnet and has a metallic ferromagnetic metastable state, which are in good agreement with the experiment. The spin magnetic moment of Co(PhPO₃)·H₂O is about 4.93 _μB${\mu }_{\mathrm{B}}$ per molecule, and it is mainly assembled at the cobalt atom, at the same time, with a little contribution from the P, O1, O2, O3.     

The size and strain effects on the Raman spectra of Ce1−xNdxO2−δ (0≤x≤0.25) nanopowders

Ultrafine Ce_1−xNd_xO_2−δ (x=0-0.25) powders were synthesized by self-propagating room temperature synthesis. Raman spectra were measured at room temperature in the 300-700 cm⁻¹ spectral range. The shift and asymmetric broadening of the Raman F_2g mode at about 454 cm⁻¹ in pure and doped ceria samples could be explained with combined size and inhomogenous strain effects. Increased concentration of O²⁻ vacancies with doping is followed by an appearance of new Raman feature at about 545 cm⁻¹.     

First principles investigation of optical properties of zinc-blende AlxGa1−xAs1−yNy materials

We have performed a first-principle Full Potential Linearized Augmented Plane Waves calculation within the local density approximation (LDA) to the zinc-blende Al_xGa_1−xAs_1−yN_y to predict its optical properties as a function of N and Al mole fractions. The accurate calculations of electronic properties such as band structures and optical properties like refractive index, reflectivity and absorption coefficient of Al_xGa_1−xAs and Al_xGa_1−xAs_1−yN_y with x≤0.375 and y up to 4% are presented. Al_xGa_1−xAs on GaAs have a lattice mismatch less than 0.16% and the lattice constant of Al_xGa_1−xAs has a derivation parameter of 0.0113±0.0024. The band gap energies are calculated by LDA and the band anticrossing model using a matrix element of C_MN=2.32 and a N level of E_N=(1.625+0.069x) eV. The results show that Al_xGa_1−xAs can be very useful as a barrier layer in separate confinement heterostructure lasers and indicate that the best choice of x and y Al_xGa_1−xAs_1−yN_y could be an alternative to Al_xGa_1−xAs when utilized as active layers in quantum well lasers and high-efficiency solar cell structures.