Tribological properties of heat-treated electroless Ni-P coatings on AZ91 alloy

Influence of heat treatment regime on adhesion and wear resistance of Ni-P electroless coating on AZ91 magnesium alloy is investigated in this work. The pretreated substrate was plated using a bath containing nickel sulphate, sodium hypophosphite and sodium acetate as main constituents. The coated samples were heat treated at 400-450 °C for 1-8 h. Adhesion of coating was estimated from the scratch test with an initial load of 8.80 N. Wear resistance was studied using the pin-on-disc method. It was found that there is no significant dependence of the coating wear resistance on heat treatment regime, as the formation of Al-Ni intermetallic sub-layers that reduce coating adhesion is limited to regions where Al₁₇Mg₁₂ phase is present in the substrate. Moreover, the coating shows good sliding properties due to the formation of oxide glazes in the wear track.     

The resistance to wear and corrosion of laser-cladding Al2O3 ceramic coating on Mg alloy

The paper presents a study on the preparation of Al₂O₃ ceramic coating on AZ91HP Mg alloy by laser remelting plasma-sprayed coating. It was found that after laser remelting, the coating exhibited obvious layer-like characteristics due to influence of temperature distribution, thermophysical parameters and layer thickness. According to the microstructural difference, the coating can be divided into the melted zone with the α-Al₂O₃ column-like crystal, the sintered zone with flock-like structure, the residual plasma-sprayed zone with loosened structure. Because of the dense column-like crystal, the hardness, wear and corrosion resistance of the laser remelted coating are much higher than those of the plasma-sprayed coating and as-received Mg alloy.     

Pb-Mg-Al合金腐蚀机理的电子理论研究

为了了解Pb-Mg-Al合金腐蚀的物理本质, 本文采用基于第一性原理的赝势平面波方法系统地计算了Pb-Mg-Al合金中各物相的结合能、费米能级和局域态密度等电子结构参数, 分析了合金的电化学腐蚀机理. 计算结果表明：Pb-Mg-Al合金中各主要组成物相稳定性大小关系为 Mg₁₇Al₁₂>Mg₂Pb>Mg;Mg,Mg₂Pb和Mg₁₇Al₁₂的费米能级存在E_f(Mg)>E_f(Mg₂Pb)>E_f(Mg₁₇Al₁₂)的关系, 说明Mg最容易失去电子, Mg₂Pb次之, Mg₁₇Al₁₂最难;局域态密度表明, 在同样的外界条件下, 体系中Mg相和Mg₂Pb相对于Mg₁₇Al₁₂均处于不稳定的状态, 容易失去电子, 即容易发生腐蚀. Pb-Mg-Al合金体系中不同物相的费米能级差构成了电化学腐蚀的电动势, 导致电子从费米能级高的Mg相和Mg₂Pb相流向费米能级低的Mg₁₇Al₁₂相, 使Pb-Mg-Al合金发生腐蚀.     

Characterization of microarc oxidation coatings formed on AM60B magnesium alloy in silicate and phosphate electrolytes

Microarc oxidation coatings on AM60B magnesium alloy were prepared in silicate and phosphate electrolytes. Structure, composition, mechanical property, tribological, and corrosion resistant characteristics of the coatings was studied by scanning electron microscope (SEM), X-ray diffraction (XRD) and microhardness analyses, and by ball-on-disc friction and potentiodynamic corrosion testing. It is found that the coating produced from the silicate electrolyte is compact and uniform and is mainly composed of MgO and forsterite Mg₂SiO₄ phases, while the one formed in phosphate electrolyte is relatively porous and is mainly composed of MgO phase. The thick coating produced from a silicate electrolyte possesses a high hardness and provides a low wear rate (3.55 × 10⁻⁵ mm³/Nm) but a high friction coefficient against Si₃N₄ ball. A relatively low hardness and friction coefficient while a high wear rate (8.65 × 10⁻⁵ mm³/Nm) is recorded during the testing of the thick coating produced from a phosphate electrolyte. Both of these types of coatings provide effective protection for the corrosion resistance compared with the uncoated magnesium alloy. The coating prepared from the silicate electrolyte demonstrates better corrosion behavior due to the compacter microstructure.     

Influence of heat treatment on tribological properties of electroless Ni-P and Ni-P-Al2O3 coatings on Al-Si casting alloy

Evolution of tribological properties of electroless Ni-P and Ni-P-Al₂O₃ coating on an Al-10Si-0.3Mg casting alloy during heat treatment is investigated in this work. The pre-treated substrate was plated using a bath containing nickel hypophosphite, nickel lactate and lactic acid. For preparation of fiber-reinforced coating Al₂O₃ Saffil fibers pre-treated in demineralised water were used. The coated samples were heat treated at 400-550 °C/1-8 h. Tribological properties were studied using the pin-on-disc method. It is found that the best coating performance is obtained using optimal heat treatment regime (400 °C/1 h). Annealing at higher temperatures (450 °C and above) leads to the formation of intermetallic compounds that reduce the coating wear resistance. The reason is that the intermetallic phases adversely affect the coating adherence to the substrate. The analysis of wear tracks proves that abrasion is major wear mechanism, however due to the formed intermetallic sub-layers, partial coating delamination may occur during the pin-on-disc test on the samples annealed at 450 °C and above. It was found that fiber reinforcement reduces this scaling and increases wear resistance of coatings as compared to the non-reinforced Ni-P coatings.     

Study on the solidification microstructure in AZ91D Mg alloy after laser surface melting

Laser surface melting (LSM) is known to enhance the wear and corrosion resistance of Mg alloys, but its effect on microstructural evolution of Mg alloys is not well understood. An effort has been made to study the effect of rapid solidification following LSM on the microstructural evolution of AZ91D Mg alloy. The results of X-ray diffractometry, scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray spectroscopy indicated that the solidification microstructure in the laser-melted zone was mainly cellular/dendrite structure of primarily α-Mg phase and continuous network of β-Mg₁₇Al₁₂ phase. Numerical prediction of the laser-melted zone suggested that cooling rates increased strongly from the bottom to the top surface in the irradiated regions. An attempt has been made to correlate dendrite cell sizes of the solidification microstructure with the cooling rates in the laser-treated AZ91D Mg alloy.     

Electrodeposition of Al-Mn alloy on AZ31B magnesium alloy in molten salts

The Al-Mn alloy coatings were electrodeposited on AZ31B Mg alloy in AlCl₃-NaCl-KCl-MnCl₂ molten salts at 170 °C aiming to improve the corrosion resistance. However, in order to prevent AZ31B Mg alloy from corrosion during electrodeposition in molten salts and to ensure excellent adhesion of coatings to the substrate, AZ31B Mg alloy should be pre-plated with a thin zinc layer as intermediate layer. Then the microstructure, composition and phase constituents of the coatings were investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDX), and X-ray diffraction (XRD). It was indicated that, by adjusting the MnCl₂ content in the molten salts from 0.5 wt% to 2 wt%, the Mn content in the alloy coating was increased and the phase constituents were changed from f.c.c Al-Mn solid solution to amorphous phase. The corrosion resistance of the coatings was evaluated by potentiodynamic polarization measurements in 3.5% NaCl solution. It was confirmed that the Al-Mn alloy coatings exhibited good corrosion resistance with a chear passive region and significantly reduced corrosion current density at anodic potentiodynamic polarization. The corrosion resistance of the alloy coatings was also related with the microstructure and Mn content of the coatings.     

稀土对镁合金应力腐蚀影响电子理论研究

建立了镁合金纯净晶界及其析出Mg₁₇Al₁₂相的晶界原子集团，应用实空间的递归方法计算了铝、稀土元素在晶界的偏聚能，晶界处铝、稀土原子间相互作用能和不同体系的费米能级.讨论了铝、稀土在晶界的偏聚行为，铝、稀土原子间的相互作用与有序化的关系及稀土对镁合金晶间应力腐蚀影响的物理本质.研究发现：铝、稀土原子偏聚于晶界；铝原子间相互排斥，在晶界区形成有序相Mg₁₇Al₁₂，稀土原子间互相吸引，形成原子团簇；稀土原子团吸引铝原子，使铝原子渗入稀土团簇中，形成稀土化合物.因此，稀土具有抑制铝在晶界形成导致应力腐蚀的阴极相Mg₁₇Al₁₂的作用，提高镁合金的晶间应力腐蚀抗力. 关键词： 电子理论 镁合金 应力腐蚀 稀土     

Effects of duty ratio at low frequency on growth mechanism of micro-plasma oxidation ceramic coatings on Ti alloy

The aim of this work is to study the effects of duty ratio on the growth mechanism of the ceramic coatings on Ti-6Al-4V alloy prepared by pulsed single-polar MPO at 50 Hz in NaAlO₂ solution. The phase composition of the coatings was studied by X-ray diffraction, and the morphology and the element distribution in the coating were examined through scanning electron microscopy and energy dispersive spectroscopy. The thickness of the coatings was measured by eddy current coating thickness gauge. The corrosion resistance of the coated samples was examined by linear sweep voltammetry technique in 3.5% NaCl solution. The changes of the duty ratio (D) of the anode process led to the changes of the mode of the spark discharge during the pulsed single-polar MPO process, which further influenced the structure and the morphology of the ceramic coatings. The coatings prepared at D = 10% were composed of a large amount of Al₂TiO₅ and a little γ-Al₂O₃ while the coatings prepared at D = 45% were mainly composed of α-Al₂O₃ and γ-Al₂O₃. The coating thickness and the roughness were both increased with the increasing D due to the formation of Al₂O₃. The formation of Al₂TiO₅ resulted from the spark discharge due to the breakdown of the oxide film, while the formation of Al₂O₃ resulted from the spark discharge due to the breakdown of the vapor envelope. The ceramic coatings improved the corrosion resistance of Ti-6Al-4V alloy. And the surface morphology and the coating thickness determined the corrosion resistance of the coated samples prepared at D = 45% was better than that of the coated samples prepared at D = 10%.     

Dry sliding wear behaviour of magnesium oxide and zirconium oxide plasma electrolytic oxidation coated magnesium alloy

Two types of PEO coatings, one consisting of magnesium oxide (MgO) and the other comprising zirconium oxide (ZrO₂) as the main phase composition were produced on AM50 magnesium alloy from alkaline and acidic electrolytes, respectively. The ZrO₂ coating was found to be spongy and thicker with a higher roughness, whilst the relatively more compact MgO coating was having contrasting features. In the dry sliding oscillating wear tests under two different loads viz., 2 N and 5 N, the ZrO₂ coating exhibited a very poor wear resistance. The MgO coating showed an excellent resistance to sliding wear under 2 N load; however, the load bearing capacity of the coating was found to be insufficient to resist the wear damage under 5 N load. The higher specific wear rates of the MgO coating under 5 N load and that of the ZrO₂ coating under 2 N and 5 N loads were attributed to the poor load bearing capacity and a three-body-abrasive wear mechanism.     

Preparation and properties of titanium oxide film on NiTi alloy by micro-arc oxidation

Titanium oxide ceramic coatings were prepared by micro-arc oxidation (MAO) in galvanostatic regime on biomedical NiTi alloy in H₃PO₄ electrolyte using DC power supply. The surface of the coating exhibited a typical MAO porous and rough structure. The XPS analysis indicated that the coatings were mainly consisted of O, Ti, P, and a little amount of Ni, and the concentration of Ni was greatly reduced compared to that of the NiTi substrate. The TF-XRD analysis revealed that MAO coating was composed of amorphous titanium oxide. The coatings were tightly adhesive to the substrates with the bonding strength more than 45 MPa, which was suitable for medical applications. The curves of potentiodynamic porlarization indicated that the corrosion resistance of NiTi alloy was significantly improved due to titanium oxide formation on NiTi alloy by MAO.     

Effect of electrodeposition modes on surface characteristics and corrosion properties of fluorine-doped hydroxyapatite coatings on Mg-Zn-Ca alloy

The microstructure, morphology and composition highly determine the corrosion resistance and bioactivity of coating. In traditional cathodic electrodeposition process, because of the unfavorable effects of the polarization of concentration difference and H₂ evolution, fluorine-doped hydroxyapatite coating was loose and porous. This coating could not ensure the long-term stability of the Mg alloy implants. In order to improve the corrosion resistance and bioactivity of coating, pulse electrodeposition and H₂O₂ were introduced into the electrodeposition to deposit fluorine-doped hydroxyapatite coating. As a comparative study, microstructure, corrosion resistance properties and bioactivity of traditional cathodic electrodeposition coating and pulse electrodeposition coating were investigated, respectively. The results revealed that nano fluorine-doped hydroxyapatite coating could be prepared by pulse electrodeposition, and the coating was dense and uniform. The potentiodynamic polarization experiment indicated that the dense and uniform coating could effectively protect Mg alloy substrate from corrosion. Immersion testing was performed in simulated body fluid. It was found that pulse electrodeposition coating could more effectively induce the precipitation of Mg²⁺, Ca²⁺ and PO₄³⁻ in comparison with traditional cathodic electrodeposition coating, because the nano phase had comparatively high specific surface area. Thus magnesium alloy coated with fluorine-doped nano-hydroxyapatite coating may be a promising candidate as biodegradable bone implants, and was worthwhile to further investigate the in vivo degradation behavior.     

Study of molybdenum/lanthanum-based composite conversion coatings on AZ31 magnesium alloy

The molybdenum/lanthanum-based (Mo/La) composite conversion coating on AZ31 magnesium alloy was investigated and the corrosion resistance was evaluated as well. The morphology, composition and corrosion resistance of the coating were studied by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and potentiodynamic polarization analysis, respectively. The results revealed that the conversion coating consisted of spherical nodular particles, which was mainly composed of Mo, La, O and Mg. After conversion treatment the corrosion potential shifts about 500 mV positively, and the corrosion current density decreases two orders of magnitude. The corrosion resistance of AZ31 alloy is remarkably improved by Mo/La composite conversion coating.     

Corrosion and wear properties of PEO coatings formed on AM60B alloy in NaAlO2 electrolytes

Coatings with a thickness of 22-32 μm were formed on an AM60B magnesium alloy by plasma electrolytic oxidation (PEO) in electrolytes containing 12.0-24.0 g/l NaAlO₂ and other additives. SEM analyses of the coated samples showed that the coatings were compact with relatively low porosity. X-ray diffraction revealed that the coatings consisted of mainly MgAl₂O₄ and MgO phases. The relative amount of MgAl₂O₄ in the coating increased with increasing NaAlO₂ concentration. The relatively compact and thick coatings provide good corrosion protection for magnesium, as indicated by the results of potentiodynamic polarization tests. In addition, the PEO treatment also significantly improved the wear resistance of the alloy. Pin-on-disk wear tests showed that the PEO treatment reduced the wear volume loss by a factor of 10.     

Composition design and laser cladding of Ni-Zr-Al alloy coating on the magnesium surface

The cluster line criterion was used for optimized design of a Ni-Zr-Al alloy used as coating on the AZ91HP magnesium alloy by laser cladding. Results show that the coating mainly consists of an amorphous, two ternary intermetallic phases with Ni₁₀Zr₇ and Ni₂₁Zr₈ type structures resulting in high hardness, good wear resistance and corrosion resistance. The interface between the clad layer and the substrate has good metallurgical bond.     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Self-assembled monolayers on magnesium alloy surfaces from carboxylate ions

Self-assembled monolayers (SAMs) of carboxylate salts (C_n−1H_2n−1COONa, n = 12, 16, 18) were successfully formed on Mg alloy substrate in ethanol solution and characterized by the contact angle measurement, ATR-FTIR, ellipsometry and XPS. The SAMs were regularly and densely anchored to the Mg alloy substrate via monodentate bonding with the tilting angles of about 40°, 33° and 27° for C12, C16 and C18 monolayers, respectively. Electrochemical impedance spectroscopy (EIS) proved the corrosion protection of SAMs for Mg alloy substrate with protective efficiency (PE) of even up to 98.5%.     

Microstructure and corrosion properties of diode laser melted friction stir weld of aluminum alloy 2024 T351

Friction stir welding is a promising solid state joining process for high strength aluminum alloys. Though friction stir welding eliminates the problems of fusion welding as it is performed below melting temperature (T_m), it creates severe plastic deformation. Friction stir welds of some aluminum alloys exhibit relatively poor corrosion resistance. This research enhanced the corrosion properties of such welds through diode laser surface melting.A friction stir weld of aluminum alloy 2024 T351 was laser melted using a 1 kW diode laser. The melt-depth and microstructure were investigated using optical and scanning electron microscopy. The melt zone exhibited epitaxially grown columnar grains. At the interface between the melted and the un-melted zone, a thick planar boundary was observed. Energy dispersive spectroscopy analyzed the redistribution of elemental composition. The corrosion properties of the laser melted and native welds were studied in aqueous 0.5 M sodium chloride solution using open circuit potential and cyclic potentiodynamic polarization. The results show noticeable increase in the pit nucleation resistance (390 mV) after the laser surface treatment. The repassivation potential was nobler to the corrosion potential after the laser treatment, which confirmed that the resistance to pit growth was improved.     

Studies on influence of zinc immersion and fluoride on nickel electroplating on magnesium alloy AZ91D

The effect of zinc immersion and the role of fluoride in nickel plating bath were mainly investigated in nickel electroplating on magnesium alloy AZ91D. The state of zinc immersion, the composition of zinc film and the role of fluoride in nickel plating bath were explored from the curves of open circuit potential (OCP) and potentiodynamic polarization, the images of scanning electron microscopy (SEM) and the patterns of energy dispersive X-ray (EDX). Results show that the optimum zinc film mixing small amount of Mg(OH)₂ and MgF₂ is obtained by zinc immersion for 30-90 s. The corrosion potential of magnesium alloy substrate attached zinc film will be increased in nickel plating bath and the quantity of MgF₂ sandwiched between magnesium alloy substrate and nickel coating will be reduced, which contributed to produce nickel coating with good performance. Fluoride in nickel plating bath serves as an activator of nickel anodic dissolution and corrosion inhibitor of magnesium alloy substrate. 1.0-1.5 mol dm⁻³ of F⁻ is the optimum concentration range for dissolving nickel anode and protecting magnesium alloy substrate from over-corrosion in nickel plating bath. The nickel coating with good adhesion and high corrosion resistance on magnesium alloy AZ91D is obtained by the developed process of nickel electroplating. This nickel layer can be used as the rendering coating for further plating on magnesium alloys.     

Structure and tribological performance by nitrogen and oxygen plasma based ion implantation on Ti6Al4V alloy

Ti6Al4V alloy was implanted with nitrogen-oxygen mixture by using plasma based ion implantation (PBII) at pulsed voltage −10, −30 and −50 kV. The implantation was up to 6 × 10¹⁷ ions/cm² fluence. The changes in chemical composition, structure and hardness of the modified surfaces were studied by XPS and nanoindentation measurements. According to XPS, it was found that the modified layer was predominantly TiO₂, but contained small amounts of TiO, Ti₂O₃, TiN and Al₂O₃ between the outmost layer and metallic substrate. Surface hardness and wear resistance of the samples increased significantly after PBII treatment, the wear rate of the sample implanted N₂-O₂ mixture at −50 kV decreased eight times than the untreated one. The sample implanted N₂-O₂ mixture showed better wear resistance than that of the sample only implanted oxygen at − 50 kV. The wear mechanism of untreated sample was abrasive-dominated and adhesive, and the wear scar of the sample implanted at −50 kV was characterized by abrasive wear-type ploughing.