Phase analysis of TaN/Ta barrier layers in sub-micrometer trench structures for Cu interconnects

The resistance behavior of TaN/Ta diffusion barrier bilayers has been investigated. The dependence of the Ta-phase on the TaN layer thickness was examined by means of X-ray micro-diffraction and resistivity measurements. Furthermore, the influence of the geometry of a damascene trench structure on the Ta-phase of the deposited TaN/Ta barrier bilayers has been studied and compared to the results obtained with blanket wafers. The influence of the Ta-phase on the via resistance of Cu interconnects is discussed.     

Structural and optical properties of Ga2(1−x)In2xO3 films prepared on α-Al2O3 (0 0 0 1) by MOCVD

Ga_2(1−x)In_2xO₃ thin films with different indium content x [In/(Ga + In) atomic ratio] were prepared on α-Al₂O₃ (0 0 0 1) substrates by the metal organic chemical vapor deposition (MOCVD). The structural and optical properties of the Ga_2(1−x)In_2xO₃ films were investigated in detail. Microstructure analysis revealed that the film deposited with composition x = 0.2 was polycrystalline structure and the sample prepared with x up to 0.8 exhibited single crystalline structure of In₂O₃. The optical band gap of the films varied with increasing Ga content from 3.72 to 4.58 eV. The average transmittance for the films in the visible range was over 90%.     

Characteristics of High In-Content InGaN Alloys Grown by MOCVD

InN and In0.46 Ca0.54N films are grown on sapphire with a CaN buffer by metalorganic chemical vapour deposition （MOCVD）. Both high resolution x-ray diffraction and high resolution transmission electron microscopy results reveal that these films have a hexagonal structure of single crystal. The thin InN film has a high mobility of 4 75 cm^2V^-1s^-1 and that oflno.46 Gao.54N is 163 cm^2 V^-1s^-1. Room-temperat ure photoluminescence measurement of the InN film shows a peak at 0.72eV, confirming that a high quality InN film is fabricated for applications to full spectrum solar cells.     

Growth of AlGaN Epitaxial Film with Chemical Vapour High A1 Content by Metalorganic Deposition

A high-Al-content AlGaN epilayer is grown on a low-temperature-deposited AlN buffer on （0001） sapphire by low pressure metalorganic chemical vapour deposition. The dependence of surface roughness, tilted mosaicity, and twisted mosaicity on the conditions of the AlGaN epilayer deposition is evaluated. An AlGaN epilayer with favourable surface morphology and crystal quality is deposited on a 2Onto low-temperature-deposited AlN buffer at a low V/Ⅲ flow ratio of 783 and at a low reactor pressure of 100 Torr, and the adduct reaction between trimethylaluminium and NH3 is considered.     

Photoluminescence characteristics from amorphous SiC thin films with various structures deposited at low temperature

Hydrogenated amorphous SiC thin films deposited at low substrate temperature (100 °C) show the different bonding configurations and microstructures which depend on the carbon concentrations in the films controlled by the gas ratio R of methane to silane during the deposition. Photoluminescence characteristics are investigated for these samples with different structures. A strong luminescence in red light region can be observed for samples deposited with low gas ratio R which is significantly reduced its intensity with increasing the carbon concentrations in the films. On the other hand, the luminescence bands located at blue-green light region are detected under UV light excitation for samples deposited with high gas ratio R, which can be associated with the existence of amorphous SiC clusters in the films.     

Growth of InN films on spinel substrates by pulsed laser deposition

We have grown InN films on MgAl₂O₄(111) substrates with atomically flat surfaces using pulsed laser deposition (PLD) and compared their structural properties with those grown on (Mn,Zn)Fe₂O₄(111) substrates. It has been revealed that InN(0001) films grow on MgAl₂O₄(111) with an in‐plane epitaxial relationship of InN[1 00] // MgAl₂O₄[1 0], achieving a lattice mismatch minimum. The InN films exhibited a clear sixfold rotational symmetry, without 30° rotational domains and with a full width at half maximum value of the InN 0002 rocking curve being 17.5 arcmin. Comparison between InN films grown on MgAl₂O₄ and those on (Mn,Zn)Fe₂O₄ led us to conclude that suppression of the interfacial reactions between the InN films and the substrate is inherently important to obtain high quality InN on substrates with a spinel structure. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effects of In and Sb mono-layers to form rotated InSb films on a Si(1 1 1) substrate

A new method for InSb heteroepitaxial growth on a Si substrate was introduced in our previous work, in which an InSb film was formed via an InSb bi-layer. In the present work, to study the effects of In and Sb individual layers on the InSb film quality, InSb was deposited onto an InSb bi-layer, In mono-layer, and Sb mono-layer on a Si substrate. It was found that both In and Sb layers (in other words, InSb bi-layer) were essential to form a fine InSb film.     

Diamond coating deposition by synergy of thermal and laser methods—A problem revisited

Diamond coatings were deposited by synergy of the hot filament CVD method and the pulse TEA CO₂ laser, in spectroactive and spectroinactive diamond precursor atmospheres. Resulting diamond coatings are interpreted relying on evidence of scanning electron microscopy as well as microRaman spectroscopy. Thermal synergy component (hot filament) possesses an activating agent for diamond deposition, and contributes significantly to quality and extent of diamond deposition. Laser synergy component comprises a solid surface modification as well as the spectroactive gaseous atmosphere modification. Surface modification consists in changes of the diamond coating being deposited and, at the same time, in changes of the substrate surface structure. Laser modification of the spectroactive diamond precursor atmosphere means specific consumption of the precursor, which enables to skip the deposition on a defined substrate location. The resulting process of diamond coating elimination from certain, desired locations using the CO₂ laser might contribute to tailoring diamond coatings for particular applications. Additionally, the substrate laser modification could be optimized by choice of a proper spectroactive precursor concentration, or by a laser radiation multiple pass through an absorbing medium.     

Nanocrystalline silicon thin-film transistors with 50-nm-thick deposited channel layer, 10 cm2V-1s-1 electron mobility and 108 on/off current ratio

Thin-film transistors were made using 50-nm-thick directly deposited nanocrystalline silicon channel layers. The transistors have a coplanar top gate structure. The nanocrystalline silicon was deposited from discharges in silane, hydrogen and silicon tetrafluoride. The transistors combine a high electron field effect mobility of ∼10 cm² V^-1s^-1 with a low ‘off’ current of ∼10^-14 A per μm of channel length and an ‘on’/‘off’ current ratio of ∼10⁸. This result shows that transistors made from directly deposited silicon can combine high mobility with low ‘off’ currents. Received: 28 May 2001 / Accepted: 30 May 2001 / Published online: 30 August 2001     

Effect of Al incorporation on the AlGaN growth by metalorganic chemical vapor deposition

The effect of Al incorporation on the AlGaN growth by metalorganic chemical vapor deposition is investigated. With the increase of trimethylalluminum (TMAl) flux, the crystal quality becomes worse, and the epilayer surface becomes rougher. An interesting phenomenon is that the growth rate of AlGaN decrease with increasing TMAl flux, which is opposite to the AlN growth rate dependence on the TMAl flux. All these effects are attributed to the different properties of Al atoms due to the higher bond strength of Al-N compared with Ga-N, which lead to lower surface mobility and stronger competitive ability of Al atoms during the growth. The enhancement of the surface mobility of Al is especially important for improving the quality of AlGaN.     

Influence of deposition conditions on the structural characteristics of sublimated CdTe thin films

In this paper the results obtained by X-ray diffraction studies on the structural characteristics of CdTe thin films deposited onto glass substrates by close-spaced sublimation technique are presented. Using different experimental arrangements and appropriate settings for growth parameters, the films with different polycrystalline structures were prepared. The geometry and the volume of the deposition chamber influence the size of film crystallites and also their preferential orientation. The role of deposition parameters such as the substrate temperature, the incidence angle, the film thickness, and the heat treatment in determination of the structural properties of the films are also investigated. Received: 26 November 1999 / Accepted: 7 January 2000 / Published online: 5 April 2000     

Solution of the optical parameters of the thin film systems and interfaces

We report on the optical parameters of the semiconductor thin films determination. The method is based on the dynamical modeling of the spectral reflectance function combined with the genetic optimization of the initial model. The spectral dependency of the thin film optical parameters computation is based on the optical transitions modeling. The combination of the dynamical modeling and the genetic optimization enable comfortable analysis of the spectral dependences of the optical parameters and incorporation of the microstructure effects on the multilayer system optical properties. The results of the optical parameters of i-a-Si thin films determination are presented.     

MOCVD Growth and Characterization of Epitaxial AlxGa1-xN Films

We study the growth of AlxGa1-x N epilayers on （0001） sapphire by low-pressure MOCVD, using a lowtemperature AIN buffer. By varying the input flow rates of trimethylgallium （TMGa）, we obtain crack-free AlGaN films in the whole range of composition. A linear relationship between gas and solid Al content is observed. The structural properties of the layers （x =0- 1） are investigated by x-ray diffraction, atomic force microscopy （AFM） and scanning electron microscopy （SEM）. It is found that a two-direction growth appears along the c-axis and the （1011） directions for x ≥ 0.45. From the results of Raman spectroscopy, we suggest that the compressive stain and the lack of mobility orAl adatoms can induce the formation of （1011） grains.     

Cathodoluminescence and structural studies of nitrided 3D gallium structures grown by MOCVD

Cathodoluminescence (CL) spectrum imaging and grazing incidence X-ray diffraction (GIXRD) are employed to investigate nitride three-dimensional (3D) gallium structures. The metallic precursors are naturally obtained on a large variety of substrates by metal-organic chemical vapor deposition (CVD) with different shape/size controlled by the growth conditions, especially the temperature. These 3D metallic structures are subsequently exposed to a nitridation process in a conventional CVD reactor to form GaN nanocrystals, as confirmed by GIXRD measurements. CL spectroscopy shows visible light emission (2.5-2.8 eV) excited from the GaN in the 3D structures.     

Impact of surface step heights of 6H-SiC (0 0 0 1) vicinal substrates in heteroepitaxial growth of 2H-AlN

Impact of step height of silicon carbide (SiC) substrates on heteroepitaxial growth of aluminum nitride (AlN) was investigated. Step-and-terrace structures with various step heights, 6 monolayer (ML), 3ML and 1ML, were formed on 6H-SiC (0 0 0 1) vicinal substrates by high-temperature gas etching. 2H-AlN layers were grown on the substrate by plasma-assisted molecular-beam epitaxy (MBE) and then these layers were characterized by atomic-force microscopy (AFM) and X-ray diffraction (XRD). High-quality AlN can be grown on SiC substrates with 6ML- and 3ML-height step, while AlN grown on SiC substrates with 1ML-height step exhibited inferior crystalline quality. A model for high-quality AlN growth on SiC substrates with 3ML-height step is proposed.     

Doped Polycrystalline 3C-SiC Films Deposited by LPCVD for Radio-Frequency MEMS Applications

Polycrystalline 3C-SiC films are deposited on SiO2 coated Si substrates by low pressure chemical vapour deposition （LPCVD） with C3H8 and SiH4 as precursors. Controlled nitrogen doping is performed by adding NH3 during SiC growth to obtain the low resistivity 3C-SiC films. X-ray diffraction （XRD） patterns indicate that the deposited films are highly textured （111） orientation. The surface morphology and roughness are determined by scanning electron microscopy （SEM） and atomic force microscopy （AFM）. The surface features are spherulitic texture with average grain size of 100nm, and the rms roughness is 20nm （AFM 5×5 μm images）. Polycrystalline 3C-SiC films with highly orientational texture and good surface morphology deposited on SiO2 coated Si substrates could be used to fabricate rf microelectromechanical systems （MEMS） devices such as SiC based filters.     

Electrical transport properties of thermally evaporated phthalocyanine (H2Pc) thin films

Thin films of H₂Pc of various thicknesses have been deposited onto glass substrates using thermal evaporation technique at room temperature. The dark electrical resistivity measurements were carried out at different temperatures in the range 298-473 K. An estimation of mean free path (l_o) of charge carriers in H₂Pc thin films was attempted. Measurements of thermoelectric power confirm that H₂Pc thin films behave as a p-type semiconductor. The current density-voltage characteristics of Au/H₂Pc/Au at room temperature showed ohmic conduction mechanism at low voltages. At higher voltages the space-charge-limited conduction (SCLC) accompanied by an exponential trap distribution was dominant. The temperature dependence of current density allows the determination of some essential parameters such as the hole mobility (μ_h), the total trap concentration (N_t), the characteristic temperature (T_t) and the trap density P(E).     

Three-Step Growth Optimization of AlN Epilayers by MOCVD

A three-step growth process is developed for depositing high-quality aluminium-nitride （AlN） epilayers on （001） sapphire by low pressure metalorganic chemical vapour deposition （LP-MOCVD）. We adopt a low temperature （LT） A1N nucleation layer （NL）, and two high temperature （HT） A1N layers with different V/Ⅲ ratios. Our results reveal that the optimal NL temperature is 840-880℃, and there exists a proper growth switching from low to high V/Ⅲ ratio for further reducing threading dislocations （TDs）. The screw-type TD density of the optimized AIN film is just 7.86×10^6 cm^-2, about three orders lower than its edge-type one of 2×10^9 cm^-2 estimated by high-resolution x-ray diffraction （HRXRD） and cross-sectional transmission electron microscopy （TEM）.     

The important role of Mn in the room-temperature ferromagnetism of Mn-doped GaN films

Mn-doped GaN films (Ga_1−xMn_xN) were grown on sapphire (0 0 0 1) using Laser assisted Molecular Beam Epitaxy (LMBE). High-quality nanocrystalline Ga_1−xMn_xN films with different Mn concentration were then obtained by thermal annealing treatment for 30 min in the ammonia atmosphere. Mn ions were incorporated into the wurtzite structure of the host lattice by substituting the Ga sites with Mn³⁺ due to the thermal treatment. Mn³⁺, which is confirmed by XPS analysis, is believed to be the decisive factor in the origin of room-temperature ferromagnetism. The better room-temperature ferromagnetism is given with the higher Mn³⁺ concentration. The bound magnetic polarons (BMP) theory can be used to prove our room-temperature ferromagnetic properties. The film with the maximum concentration of Mn³⁺ presents strongest ferromagnetic signal at annealing temperature 950 °C. Higher annealing temperature (such as 1150 °C) is not proper because of the second phase Mn_xGa_y formation.     

Optical and Structural Properties of Mn-Doped GaN Grown by Metal Organic Chemical Vapour Deposition

Mn-doped GaN epitaxial films were grown by metal organic chemical vapour deposition （MOCVD）. Microstructural properties of films are investigated using Raman scattering. It is found that with increasing Mn-dopants levels, longitudinal optical phonon mode A1 （LO） of films is broadened and shifted towards lower frequency. This phenomenon possibly derives from the difference in bonding strength between Ga-N pairs and Mn-N pairs in host lattice. In addition, optical properties of films are investigated using cathodoluminescence and absorption spectroscopy. Mn-related both emission band around 3.0eV and absorption bands around 1.5 and 2.95eV are observed. By studies on structural and optical properties of Mn-doped GaN, we find that Mn ions substitute for Ga sites in host lattice. However, carrier-mediated ferromagnetic exchange seems unlikely due to deep levels of Mn acceptors.