Surface oxidation behavior of MgNd alloys

The oxidation kinetics of MgNd alloys oxidized in pure O₂ at high temperatures has been investigated. The results revealed two stages of the reaction: A fast initial oxidation was followed by a slow oxide growth with a parabolic kinetics. For MgNd alloys (Nd = 25 wt.%), the oxidation rate increased with the enhancement of the oxidation temperature. A sudden ignition was found for this alloys oxidized at 873 K up to about 80 min. Moreover, the increase of the Nd content would harm the oxidation resistance of the MgNd alloys. By Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis, it was found that a triplex structure of oxide film formed. The outer layer was composed of MgO, Nd₂O₃ and Nd(OH)₃, the middle layer mainly consisted of MgO and Nd₂O₃, and the inner layer was the transitional layer made of MgO, Nd₂O₃ and the content of the substrate. The protective oxidation was associated with the formation of the dense Nd₂O₃/MgO layer during isothermal oxidation process. The oxidation mechanisms for the formation of oxide film are discussed.     

Influence of titanium ions implantation on corrosion behavior of zirconium in 1 M H2SO4

In order to study the effect of titanium ion implantation on the aqueous corrosion behavior of zirconium, specimens were implanted with titanium ions with fluence ranging from 1 × 10¹⁶ to 1 × 10¹⁷ ions/cm², using a metal vapor vacuum arc (MEVVA) source at an extraction voltage of 40 kV. The valence states and depth distributions of elements in the surface layer of the samples were analyzed by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES), respectively. The potentiodynamic polarization technique was employed to evaluate the aqueous corrosion resistance of implanted zirconium in a 1 M H₂SO₄ solution. It was found that a significant improvement was achieved in the aqueous corrosion resistance of zirconium implanted with titanium ions. The larger the fluence, the better is the corrosion resistance of implanted sample. Finally, the mechanism of the corrosion behavior of titanium-implanted zirconium was discussed.     

Effect of copper ions implantation on corrosion behavior of zircaloy-4 in 1 M H2SO4

In order to study the effect of copper ion implantation on the aqueous corrosion behavior, samples of zircaloy-4 were implanted with copper ions with fluences ranging from 1 × 10¹⁶ to 1 × 10¹⁷ ions/cm², using a metal vapor vacuum arc source (MEVVA) operated at an extraction voltage of 40 kV. The valence states and depth distributions of elements in the surface layer of the samples were analyzed by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES), respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the copper ion implantation. The potentiodynamic polarization technique was employed to evaluate the aqueous corrosion resistance of implanted zircaloy-4 in a 1 M H₂SO₄ solution. It was found that a significant improvement was achieved in the aqueous corrosion resistance of zircaloy-4 implanted with copper ions when the fluence is smaller than 5 × 10¹⁶ ions/cm². The corrosion resistance of implanted samples declined with increasing the fluence. Finally, the mechanism of the corrosion behavior of copper-implanted zircaloy-4 was discussed.     

Role of chromium ion implantation on the corrosion behavior of zirconium in 1N H2SO4

In order to study the effect of chromium ion implantation on the aqueous corrosion behavior of zirconium, specimens were implanted by chromium ions with a dose range from 1×10¹⁶ to 1×10¹⁷ ions/cm², using MEVVA source at an extracted voltage of 40 kV. The valence and elements penetration distribution of the surface layer were analyzed by X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES), respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the micro-morphology and microstructure of chromium-implanted samples. The potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zirconium in a 1N H₂SO₄ solution. It was found that a significant improvement was achieved in the aqueous corrosion resistance of zirconium compared with that of as-received zirconium. The mechanism of the corrosion resistance improvement of chromium-implanted zirconium is probably due to the addition of the chromium oxide dispersoid into the zirconium matrix.     

XPS study of the surface chemistry on AZ31 and AZ91 magnesium alloys in dilute NaCl solution

The surface chemistry on AZ31 and AZ91 magnesium alloys was characterized by X-ray photoelectron spectroscopy (XPS) in the corrosion and the passivation zones. In the corrosion zone, the presence of Mg(OH)₂ and MgCO₃ species was found in the outer surface, whereas, in the inner layer, the co-existence of Mg(OH)₂, MgO and MgCO₃ species was observed for both alloys. The presence of Al³⁺ in the surface electrolyte to form Al₂O₃/Al(OH)₃ and the formation of carbonate product provide a better passivation on the surfaces and retard the chloride-induced corrosion on the materials in the passivation zone.     

Determination of growth modes via spectroscopy: new simple analytical models

Analytical models for the determination of thin film growth modes were developed on the basis of the simultaneous multilayer (SM) growth model. The models take into account up-step and down-step diffusion, enabling quick identification of the growth modes from experimentally obtained spectroscopic data. We tested the models by applying them to growth data from the literature that had been recorded via Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), and low-energy ion scattering (LEIS). We discuss the applicability of the new analytical models in comparison with the diffusion-corrected simultaneous multilayer (DCSM) model.     

XPS study of SnTe(1 0 0) oxidation by molecular oxygen

The interaction between the (1 0 0) surface of SnTe single crystal and molecular oxygen was studied by means of X-ray photoelectron spectroscopy (XPS). Analysis of the obtained spectra shows that the mechanism of surface oxidation does not change in the range of oxygen exposure 10⁸-10¹³ L. During the oxidation an additional component shifted 1.1 eV towards higher binding energies appears in the Sn 3d spectra. The Te 3d_5/2 spectra fitting reveals two additional components with binding energies close to Te⁰ and Te⁺⁴. The dependence of the additional components fraction in both Sn 3d and Te 3d_5/2 spectra on the oxygen exposure is semi-logarithmic. On the base of the experimental data two possible mechanisms are proposed.     

Chemical and structural analysis of low-temperature excimer-laser annealing in indium-tin oxide sol-gel films

We investigated the influence of excimer-laser annealing (ELA) on the electrical, chemical, and structural properties of indium–tin oxide (ITO) films prepared by a solution process. The ITO film was prepared by the sol-gel method and annealed by excimer-laser pulses with an energy density up to 240?mJ/cm². Hall measurements showed that the ELA substantially enhanced the electrical properties of the ITO films, including their resistivity, carrier density, and mobility, as increasing the laser energy density. In-depth x-ray photoelectron spectroscopy analysis of the chemical states in the film surface showed that the ELA reduced carbon species and promoted both an oxidation and crystallization. These changes were consistent with results of x-ray diffraction and transmission electron microscopy measurements, where expansions in the microcrystal growth were observed for higher laser energy density. We comprehensively understand that the chemical rearrangement and concomitant crystallization are the main factors for achieving the electrical properties during the ELA. These results suggest the potential of the ELA-treated sol-gel films for providing high-quality ITO films at low temperatures toward the flexible device applications.     

The influence of implanted yttrium on the cyclic oxidation behaviour of 304 stainless steel

High-temperature alloys are frequently used in power plants, gasification systems, petrochemical industry, combustion processes and in aerospace applications. Depending on the application, materials are subjected to corrosive atmospheres and thermal cycling. In the present work, thermal cycling was carried out in order to study the influence of implanted yttrium on the oxide scale adherence on 304 steel specimens oxidised in air at 1273 K. In situ X-ray diffraction indicates that the oxides formed at 1273 K are different on blank specimens compared to implanted specimens. Glancing angle XRD allows to analyse the oxide scale composition after cooling to room temperature.Experimental results show that yttrium implantation at a nominal dose of 10¹⁷ ions cm⁻² does not improve significantly the cyclic oxidation behaviour of the austenitic AISI 304 steel. However, it appears that yttrium implantation remarkably enhance the oxidation resistance during isothermal oxidation. It reduces the transient oxidation stage and the parabolic oxidation rate constant by one order of magnitude.     

The effect of Pt on Ni3Al surface oxidation at low-pressures

The fully-oxidized surface that forms on (1 1 1) oriented Ni₃Al single crystals, with and without Pt addition, at 300-900 K under oxygen pressures of ca. 10⁻⁷ Torr was studied using XPS, AES, and LEIS. Two main types of surfaces form, depending upon oxidation temperature. At low-temperature, the predominant oxide is NiO, capped by a thin layer of aluminum oxide, which we refer to generically as Al_xO_y. At high-temperature (i.e., 700-800 K), NiO is replaced by a thick layer of Al_xO_y. By comparing samples that contain 0, 10 and 20 at.% Pt in the bulk, we find that the effect of Pt is to: (1) reduce the maximum amount of both NiO and Al_xO_y; and (2) shift the establishment of the thick Al_xO_y layer to lower temperatures. Platinum also decreases the adsorption probability of oxygen on the clean surface.     

铸态AZ31镁合金强流脉冲离子束改性

利用强流脉冲离子束（C+,H+）对变形镁合金AZ31的压铸件靶材分别进行1,5,10,20,30,50和100次辐照实验,分析辐照前后表面形貌和相组成,并检测辐照表面及横截面沿深度方向显微硬度。结果表明:HIPIB辐照次数对靶材形貌影响较大,多次辐照使靶材熔坑呈周期性变化趋势;-Mg17Al12相弥散分布于-Mg相中。1～30次辐照,表面显微硬度提高,其主要原因为晶粒细化及微应变导致的晶体缺陷;30～50次辐照,显微硬度显著降低,其原因在于晶体缺陷的演变,如位错移动导致的小角度晶界形成,甚至出现回复再结晶过程;50～100次辐照表面显微硬度略有降低,其原因在于辐照表面组织结构及热力学行为达到稳定态。辐照效应形成冲击应力波导致长程硬化,20次辐照的横截面显微硬度在距表层30 m和240 m处分别达到极大值1.0 GPa和1.3 GPa。     

Surface composition modification of high-carbon low-alloy steels oxidized at high temperature in air

Segregating alloys across a metal/oxide interface, which occurs when an iron alloy is heated at high temperature in air, was studied on five high-carbon low-alloy steels. The metallographic analyses showed differences between the oxidation kinetics, the decarburisation rates of the surfaces and the number of surface defects. The results of the AES analyses enabled the characterization of the concentration profiles of the alloy elements and to explain the differences observed between the oxidation kinetics, the decarburisation rates and the number of surface defects. All the concentration profiles are discussed and possible mechanisms are proposed in order to understand the profiles obtained.     

Core level spectroscopy and RHEED analysis of KGd0.95 Nd0.05(WO4)2 surface

A study of the surface structure and electronic properties of (010) KGd_0.95Nd_0.05(WO₄)₂ (Nd:KGW) using RHEED analysis and XPS is presented. It is shown that Nd doping has a negligible effect on the core levels of the basic elements. A bombardment of the Nd:KGW crystal with 3-keV Ar ions results in surface amorphization accompanied by the generation of tungsten ions in lower valence states.     

Composition and corrosion resistance of cerium conversion films on the AZ31 magnesium alloy and its relation to the salt anion

Pre-treatments based on different cerium salts were applied to the AZ31 Mg alloy. The pre-treatments were performed by immersion in solutions of various Ce(III) salts: cerium chloride, cerium nitrate, cerium sulphate and cerium phosphate. The chemical composition of the treated surfaces was investigated by X-ray photoelectron spectroscopy and Auger electron spectroscopy, whereas the corrosion behaviour of the pre-treated AZ31 substrates was investigated in 0.005 M NaCl solutions using potentiodynamic polarisation and open circuit potential monitoring. The surface film contained a mixture of Ce(IV) and Ce(III) salts. The film thickness depends upon the cerium salt used. The electrochemical results show that all the conversion pre-treatments reduced the corrosion activity of the AZ31 Mg alloy substrates in the presence of chloride ions. The corrosion protection efficiency is related with the anion present in the cerium salt.     

Characterization of rare-earth conversion films formed on the AZ31 magnesium alloy and its relation with corrosion protection

Two pre-treatments were studied for AZ31 Mg alloy substrates, consisting of immersion in cerium nitrate and lanthanum nitrate solutions for various immersion times. The surface composition was investigated by X-ray photoelectron spectroscopy and Auger electron spectroscopy that revealed the presence of a surface film containing the rare-earth cation, with a composition which was time dependent in the case of the cerium pre-treatment.The corrosion behaviour of the pre-treated substrates in 0.005 M NaCl solutions was assessed by potentiodynamic polarization, open circuit potential monitoring and the scanning vibrating electrode technique (SVET). The electrochemical results show that the pre-treatments reduced the corrosion activity of the AZ31 Mg alloy substrates in the presence of chloride ions. The corrosion protection efficiency is dependent on the treatment time.     

Correlation between the surface chemistry and the atmospheric corrosion of AZ31, AZ80 and AZ91D magnesium alloys

X-ray photoelectron spectroscopy (XPS) was used in order to investigate the correlation between the surface chemistry and the atmospheric corrosion of AZ31, AZ80 and AZ91D magnesium alloys exposed to 98% relative humidity at 50 °C. Commercially pure magnesium, used as the reference material, revealed MgO, Mg(OH)₂ and tracers of magnesium carbonate in the air-formed film. For the AZ80 and AZ91D alloys, the amount of magnesium carbonate formed on the surface reached similar values to those of MgO and Mg(OH)₂. A linear relation between the amount of magnesium carbonate formed on the surface and the subsequent corrosion behaviour in the humid environment was found. The AZ80 alloy revealed the highest amount of magnesium carbonate in the air-formed film and the highest atmospheric corrosion resistance, even higher than the AZ91D alloy, indicating that aluminium distribution in the alloy microstructure influenced the amount of magnesium carbonate formed.     

A study of the formation and oxidation of PtSi by SR-PES

In the paper we present the results on the formation of platinum silicide (PtSi) by means of synchrotron radiation photoelectron spectroscopy (SR-PES) and show the effect of a Pt/Si sample exposure to both a low and high-pressure oxygen atmosphere at the end of an annealing process. We have carried out a detailed analysis of high resolution photoelectron spectra of the Pt 4f and Si 2p peaks which were taken during the sample annealing at specific temperatures. In addition to the generally known Pt₂Si and PtSi phases we have recognized an additional intermediate phase during the formation of Pt₂Si and attributed it to the Pt₃Si phase. We have proved that silicon diffuses towards the sample surface. The results of a low-pressure oxygen experiment have shown that oxygen binds only to surface silicon, however, in the case of a PtSi sample prepared externally in the ON Semiconductor labs under nitrogen/oxygen atmosphere oxygen binds not only to surface silicon but also takes over Si atoms out of the PtSi phase which results in the formation of a SiO₂ layer on almost pure platinum.     

纯锆上离子注入钇和镧后的表面分析

用金属蒸汽真空弧源，以40kV加速电压对纯锆样品分别进行了10¹⁶—10¹⁷/cm²的钇、镧离子注入，注入温度约为130℃.然后对注入样品进行表面分析.x射线光电子能谱分析表明，注入的钇以Y₂O₃形式存在，镧以La₂O₃形式存在.俄歇电子能谱表明，纯锆基体表面的氧化膜厚度随着离子注入剂量的增加而增加，当离子注入剂量达到10¹⁷/cm²时，氧化膜的厚度达到了最大值.卢瑟福背散射显示镧层的厚度约为30nm，同时直接观察到当离子注入剂量为(La+Y)10¹⁷/cm²时，纯锆样品表面发生了严重的溅射. 关键词： 纯锆 钇和镧离子共注入 卢瑟福背散射 x射线光电子能谱     

强磁与应力场耦合作用下AZ31镁合金塑性变形行为

研究强磁场对AZ31镁合金塑变能力和微观组织的作用,在3 T脉冲强磁场条件下对合金进行磁场耦合应力时的拉伸实验.采用电子背散射衍射、Ⅹ射线衍射和透射电镜分析等方法研究材料的微观组织.结果表明:与0 T拉伸试样相比,3 T拉伸试样抗拉强度和延伸率分别提高了2.2%和28.7%,说明将强磁场耦合作用于材料塑性变形过程时,能在不降低材料强度的同时提高镁合金的塑性变形能力,有助于同步改善材料强韧性.磁场作用机理主要表现为磁致塑性效应,计算表明主要合金相β(Mg_(17)Al_(12))为顺磁性,有助于发挥磁场作用效果.磁场提高了位错运动灵活性并促使位错增殖,晶界处位错堆积和应力集中促进了再结晶形成,晶粒发生细化,发挥细晶强韧化效果;同时磁场诱发塑性变形时的晶粒转动,新生成非基面取向的晶粒弱化了镁合金(0001)基面织构,该组织特征有助于提高材料的塑变能力.     

Initial growth of platinum on oxygen-covered Ni(1 1 0) surfaces

The initial growth of Pt on the Ni(1 1 0)-(3 × 1)-O and NiO(1 1 0) surfaces has been studied by coaxial impact collision ion scattering spectroscopy (CAICISS), low energy electron diffraction (LEED) and X-ray photoelectron spectroscopy (XPS). Prior to Pt deposition, the atomic structure of the near-surface regions of the Ni(1 1 0)-(3 × 1)-O and NiO(1 1 0) structures were studied using CAICISS, finding changes to the interlayer spacings due to the adsorption of oxygen. Deposition of Pt on the Ni(1 1 0)-(3 × 1)-O surface led to a random substitutional alloy in the near-surface region at Pt coverages both below and in excess of 1 ML. In contrast, when the surface was treated with 1800 L of atomic oxygen in order to form a NiO(1 1 0) surface, a thin Pt layer was formed upon room temperature Pt deposition. XPS and LEED data are presented throughout to support the CAICISS observations.