Structure and properties of TiC-TiNi composites alloyed with iron

The structure, composition, and mechanical properties of iron-alloyed TiC-TiNi composite materials are studied. When the titanium carbide framework is sintered with iron and then impregnated with titanium nickelide, iron atoms are found to diffuse into the matrix and form the B2 structure that is inhomogeneous (gradient) in chemical composition and properties and exhibits various temperatures of martensitic transformation. The latter fact shows up in the broadening of the martensitic transformation hysteresis and its shift toward low temperatures with increasing iron content. At room temperature, the strength properties of gradient-matrix TiC-TiNi composites are shown to increase with iron concentration.     

Microstructure and mechanical properties of selective laser melted magnesium

The effects of laser processing parameters on the microstructure and mechanical properties of selective laser-melted magnesium were investigated. The results show that the microstructure characteristics of the laser-melted samples are dependent on the grain size of SLM magnesium. The grains in the molten zone coarsen as the laser energy density increases. In addition, the average hardness values of the molten zone decreases significantly with an increase of the laser energy densities and then decreased slowly at a relatively high laser energy density irrespective of mode of irradiation. The hardness value was obtained from 0.59 to 0.95 GPa and corresponding elastic modulus ranging from 27 to 33 GPa. The present selective laser-melted magnesium parts are promising for biomedical applications since the mechanical properties are more closely matched with human bone than other metallic biomaterials.     

Structure and properties of laser quenched 4Cr13 steel

The structure and properties of laser quenched 4Cr13 steel were reported. The results show that: (1) Fine martensite is obtained after laser quenching. The highest content of retained austenite in the surface area 10 μm thick of laser hardened zone is 47. 13 percent, but only 3.6 percent of retained austenite is measured inside the laser hardened layer after the surface layer 10μm thick is worn off. (2) The hardness of laser quenched layer is much higher (HV_(0.1) 690) than that of the substrate (HV_(0.1) 237). (3) The wear resistance of laser quenched layer is 3.3 times higher than that of traditionally treated specimen and the corrosion resistance of 4Cr13 steel is also improved greatly by laser quenching.     

激光喷丸改善TC6钛合金组织和力学性能

为了使激光冲击强化技术能较好地应用于TC6钛合金的发动机叶片,对TC6钛合金进行试验研究。通过X射线衍射仪、透射电子显微镜等测试技术分析了不同参数下TC6钛合金的微观组织变化,用显微硬度计和残余应力测试仪分别表征表层硬度和残余应力变化,并测试材料冲击后的振动高周疲劳性能。试验结果表明：激光冲击材料后表面组织得到明显细化,随着冲击次数的增加,先后出现了高密度位错、位错胞、亚晶和纳米晶。性能方面,表面硬度在冲击一次即可提高19%,硬度影响深度达到700 m;与此同时表面残余应力最高达到-608.5 MPa,在500 m深度上仍具有-100 MPa左右的应力存在。经三次冲击后,标准疲劳试片的疲劳极限提高近20%。     

Alcohol-assisted photoetching of silicon carbide with a femtosecond laser

Femtosecond lasers have proved to be effective tools for micromachining silicon carbide material. In the drilling process, however, when the debris around the hole was not removed efficiently, the depth of hole would not increase further. In this paper, alcohol-assisted photoetching of 6H silicon carbide was investigated using a femtosecond laser. Machining in the presence of alcohol was beneficial to the debris ejection from the hole. The alcohol flow and volatilization was also helpful to further carry away the ablation debris and reduce the ablated material redeposition. The experiment showed that photoetching assisted by alcohol produced cleaner ablation effect and deeper hole than in ambient air. Moreover, alcohol assistance would not produce additional thermal damage around the hole. Vias were formed in a 250 μm thick wafer with alcohol-assisted photoetching technique using a femtosecond laser, which demonstrated the potential for this processing technique.     

Structure and magnetic properties of mechanically alloyed ferrite nanopowders

The morphology, structure parameters, and magnetic characteristics of mechanically alloyed magnetite and cobalt and magnesium spinel-ferrite nanopowders are investigated. The effect of the nanopowder particle size on the saturation magnetization of the spinel ferrites and the roles of the surface anisotropy and magnetoelastic energy in the formation of the magnetic anisotropy of the materials under study are discussed within the framework of a core-shell model. __________ Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 9, pp. 40–44, September 2006.     

激光微细熔覆快速原型制造的厚膜电容组织性能

针对传统工艺制备的厚膜电容尺寸有限、容量低、损耗大，仅限于一些特定的应用领域，提出采用激光微细熔覆快速原型制造技术在陶瓷基板上制备电容，它具有速度快，不需要掩膜等特点。着重分析电容器的组织性能以及电容、介电常数、品质因数和绝缘电阻等电器性能，并对电容器的形成机理进行了研究。实验证明，激光微细熔覆快速原型制造技术比传统烧结工艺制备的厚膜电容容量大、再现性好，其组织致密、均匀，不存在界面成分的扩散。     

Structure and properties of soda lime silicate glass doped with rare earth

Soda-lime-silicate glasses doped with different rare-earth oxides (La₂O₃, CeO₂, Nd₂O₃, Gd₂O₃ and Y₂O₃) of 1 mol% content were prepared with the traditional melting-quenching methods. In order to reveal the effects of rare-earth elements on the behavior of soda-lime-silicate glass, the structure of soda-lime-silicate glasses doped with different rare-earth oxides were determined with Fourier transform infrared spectrometer using the KBr method, and viscosity of glass melts were measured by the rotating crucible viscometer, the melting temperature of the studied glasses were derived on the basis of Arrhenius Equation, moreover the density, bending strength and molar volume were measured and calculated. The effect of rare-earth dopants on the structure of soda-lime-silicate was analyzed by a shift of peak position and variation in the full-width at half-maximum. The effect of doping rare-earth oxides into glass on the viscosity, density and bending strength was interpreted by changing in structure of soda-lime-silicate glasses doped with rare-earth oxides.     

Structure and physical properties of titanium diselenide intercalated with nickel

The structure, electrical resistivity, thermopower, and magnetic susceptibility of titanium diselenide intercalated with nickel (N_xTiSe₂) are studied systematically in the nickel concentration range x=0–0.5. In accordance with a model proposed earlier, strong hybridization of the Ni3d/Ti3d states is observed, giving rise to suppression of the magnetic moment because of delocalization of the nickel d electrons. It is shown that the strain caused by the Ni3d/Ti3d hybridization does not change the local coordination of a titanium atom.     

钛合金纳秒激光打孔数值模拟和实验研究

为了描述纳秒激光对钛合金打孔过程中孔的形貌及温度场的变化规律,建立激光打孔的物理模型,利用ANSYS中APDL语言进行编程,对温度场进行仿真分析,并利用单元生死技术模拟孔形貌的变化过程。从有限元数值模拟和实验两方面综合分析比较了激光工艺参数(脉冲能量和脉冲数量)对打孔质量(孔深和孔径)的影响,系统论述了钛合金纳秒激光打孔的一般规律,以达到工艺参数优化,提高打孔质量的目的。     

激光冲击强化对激光增材TC4钛合金组织和抗氧化性的影响

近年来,激光增材制造技术(3D打印)成为科学研究及工业应用领域的热点。为了研究激光冲击强化对增材制造TC4钛合金性能的影响,本文采用能量为5 J,波长为1 064 nm,脉宽为10 ns,光斑直径为3 mm的脉冲激光对3D打印TC4钛合金进行激光冲击强化,分析了激光冲击强化前后材料的显微硬度、显微组织、残余应力以及高温氧化性能。结果表明,经过激光冲击强化后,材料的显微硬度比激光冲击强化前提高了8%,影响层深度达到0.4 mm,强化区域的晶粒得到细化,位错增多,并产生形变孪晶;激光冲击强化的残余压应力数值高达472 MPa,材料的高温抗氧化性能也得到改善。     

Microstructure and friction and wear behavior of laser boronizing composite coatings on titanium substrate

Three kinds of laser boronizing composite coatings were in situ synthesized on Ti substrate by using powders of B, BN and B₄C as starting materials. Microstructures of the laser boronizing composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM); and their worn surface morphologies were also observed by using SEM. Moreover, the friction and wear behavior of the boronizing composite coatings under dry sliding condition were evaluated using a UMT-2MT friction and wear tester. It was found that all the three types of laser boronizing composite coatings had higher microhardness and better wear resistance than pure Ti substrate; and their microstructure and wear resistance varied with varying pre-placed powders of B, BN, and B₄C. Under the same dry sliding test conditions, the wear resistance of the three kinds of laser boronizing composite coatings, i.e., sample 1 prepared from pre-placed B, sample 2 obtained from pre-placed BN, and sample 3 fabricated from pre-placed B₄C, is ranked in an order of sample 1 > sample 2 > sample 3, which, surprisingly, well conforms to their order of hardness and friction coefficients.     

实虚部关联的量子噪声和泵噪声对单模激光动力学性质的影响

采用具有实虚部关联的量子噪声和泵噪声驱动的单模激光损失模型，用线性化近似方法研究了反映激光动力学性质的光强关联函数，讨论了光强关联函数随时间的演化；并对线性化近似方法的适用范围进行了详细分析，分别讨论了量子噪声强度、泵噪声强度、量子噪声实虚部关联系数对光强相对涨落的影响，得出在小噪声、远离阈值时，线性化近似方法适用范围扩大；小噪声、远离阈值且当量子噪声实虚部无关联时，线性化近似方法适用范围最大的结论. 关键词： 单模激光 光强关联函数 光强相对涨落     

Stationary properties of a single-mode laser system with non-Gaussian and Gaussian noise

A single-mode laser system with non-Gaussian and Gaussian noise is investigated. The stationary mean value and the normalized variance of the laser intensity are numerically calculated under the condition that the stationary probability distribution function (SPDF) is derived. The SPDF as a function of the laser intensity exhibits a maximum. The maximum becomes smaller with the increase of the correlation intensity or the non-Gaussian parameter, where the later is a measure of the deviation from the Gaussian characteristic. The maximum becomes larger as the correlation time increases. The laser intensity stationary mean value decreases with the increase of the correlation intensity or the non-Gaussian parameter while increases with the correlation time increasing. The laser intensity normalized variance increases with the increase of the correlation intensity or the non-Gaussian parameter while decreases as the correlation time increases.     

硅中钛杂质对激光电场分布影响的数值模拟

采用T-matrix数值方法模拟光学系统常用的光学材料硅中金属钛杂质对激光电场分布的影响。分析了不同球形杂质数目、不同杂质球半径、不同球形杂质间距、不同球形杂质排列以及不同相对介电常数杂质对激光电场分布的影响,通过数值模拟了解到：电场幅值的最大值总是出现在沿入射波极化方向上,电场幅值的增大与相邻两球的耦合有关,且两球间距越小电场幅值的最大值越大;相对介电常数实部越小、虚部越大的杂质会导致较大的电场幅值最大值。     

Laser-induced changes in titanium by femtosecond,picosecond and millisecond laser ablation

In order to realize the qualitative control of the laser-induced changes trend and the quantitative control of the laser-induced changes range in titanium upon laser irradiation with different pulse duration, comparative ablation experiments by femtosecond, picosecond and millisecond pulsed lasers were carried out on titanium in this study. Then the final surface morphology, aspect ratio, chemical composition and microstructural state of the ablated titanium were analyzed by laser scanning confocal microscopy, X-ray photoelectron spectroscopy and transmission electron microscopy, respectively. The dependency of the morphology, size, composition and microstructure of ablated titanium on laser pulse duration variation were emphatically discussed. It is found that, as the laser pulse duration increases from femtosecond to millisecond scale, surface morphology quality of ablated titanium gets worse, aspect ratio of microgroove decreases, proportion of titanium oxides in final ablation products becomes larger and the microstructural state of ablated titanium has a higher amorphization degree, which can be attributed to the decreased laser intensity per pulse and enhanced heat conduction effect in titanium with the pulse duration increasing.     

Investigation of titanium nitride coating by broadband laser ultrasonic spectroscopy

We present a laser ultrasonic method to investigate a titanium nitride(TiN) coating specimen.The technique is based on the principle of surface acoustic wave (SAW) dispersion during acoustic propagation on a half-space with the presence of a thin layer.Due to the high efficiency of laser line-source excitation,we have been able to generate and detect a SAW with an excellent signal-to-noise ratio in a wide frequency band.An inverse fitting algorithm was employed to extract simultaneously the thickness and the elastic parameters of the TiN coating from the experimental SAW velocity dispersion curve.     

Nd:YSAG单晶的光谱和激光性能

用提拉法生长了(1.5 at.%)Nd~(3+):Y_3Sc_2Al_3O_(12)(YSAG)激光晶体,摇摆曲线表明晶体结晶质量优良.测量了该晶体的吸收和发光光谱,表明其适合成熟的808 nm激光二极管(LD)抽运,其~4F_(3/2)→~4I_(11/2)跃迁最强发射波长为1059 nm,发射截面为1.03×10~(-19)cm~2,同时其激光上能级寿命为253μs,表明Nd:YSAG具有和Nd:YAG相近的效率,但其激光上能级寿命比Nd:YAG长约20μs.以LD抽运2 mm×2 mm×6 mm Nd:YSAG激光棒,激光阈值为0.85 W,最高输出功率为1.1 W,激光斜效率为21.1%,光-光转化效率为18.3%.综合表明Nd:YSAG单晶作为激光性能优良的全固态激光材料,更适合全固态调Q激光输出.     

Luminescence and lasing properties of neodymium- and uranium-activated inorganic laser liquids

An attempt was made to describe and show the possibilities of new inorganic neodynium- and uranium-activated laser liquids: SO₂-GaCl₃-NdCl₄; SO₂Cl₂-GaCl₃-NdCl₃-UO₂Cl₂; POCl₂-MCl_n-NdCl₃-UO₂Cl₂ for development and synthesis of direct nuclear reaction-excited lasers. Luminescence data presented in the work were used to calculate the luminescence parameters of the laser liquids such as oscillator strengths f, probability of spontaneous radiation A, intermultiplet luminescence branching coefficient β, cross-section for induced radiation σ, luminescence decay time τ, quantum yield η, and others. It is shown that the oscillator strengths of the normal absorption bands of Na³⁺, which play the main part in the pumping processes, exceed the oscillator strengths of Na³⁺ for aqueous and many other nonaqueous systems. In the luminescence excitation spectra of the Na³⁺ ion, bands are isolated in the range 400–1000 nm atλ _rec =1.06 μm. With excitation, luminescence occurs through the⁴F_3/2→⁴I_{9/2,11/2.13/2} channels. Luminescence spectral data are related to the lasing parameters. The threshold lasing energy is∼18 J/cm³. For a resonator with mirros h₁=100% and h₂=20, 40, 56, and 80%, the lasing energy is∼20–120 MJ/cm³ in the pumping energy range 18–180 J/cm³. The differential efficiency is ∼0.2% The substantial angular radiation divergence (θ∼4·10⁻² rad) and strong thermostatic distortions that occur in the active element (dn/dT≈−1.9·10⁻⁴K⁻¹) are a disadvantage of laser liquids. It is shown that operation of neodymium- and uranium-activated inorganic liquid lasers is stable under the present conditions. A. I. Gertsen Russian State Pedagogical University, Moika Embankment, 48, St. Petersburg, 191186, Russia. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 5, pp. 607–619, September–October, 1997.     

An investigation on the patina of ancient bronze coins

The patina of ancient bronze coins of different historical periods (from VI cent. A.D. to X cent. A.D.) coming from different Mediterranean countries was investigated with different surface physical analyses. X-ray photoelectron spectroscopy measurements were performed by using electron emission induced by 1.4 keV X-rays. Laser ablation coupled to mass quadrupole spectrometry analyses were developed by using a pulsed Nd:YAG laser operating at 532 nm, 3 ns pulse width, 30 mJ pulse energy and 10 Hz repetition rate, coupled to a mass quadrupole spectrometer with a mass range of 1–300 amu. Laser ablation induces controllable surface layers removal in high vacuum. At present, the mass spectrometer detects chemical elements and compounds. This work, more than to solve a numismatic question, has been carried out in order to test the validity of the above experimental techniques in view to further analyse the same coins, based on better quality statistics. Preliminary results presented in this paper indicate significant differences in the chemistry of the coins patina.