Dependence of surface nano-structural modifications of Ti implanted by N ions on temperature

The surface modification of titanium thin foil/sheet samples (0.5 mm) implanted by nitrogen ions of 30 keV energy and a fluence of 1 × 10¹⁸ N⁺ cm⁻² at different temperatures is studied using XRD, AFM, SEM, and SIMS. XRD patterns showed the development of titanium nitride with different compositions in the implanted samples, while the presence of different titanium compositions such as titanium oxides was also observed. AFM images at 654 K showed the formation of grains, that after initial sputtering of the grain boundary at 728 K temperature, the morphology of the surface changed from small grains to a bimodal distribution of grains at 793 K which consisted of larger grains with bright hillocks within them. This was considered to be due to phase transformation/compositional changes, explained by correlating XRD and SIMS results. The SIMS results showed a maximum at about 730 K and a minimum at about 790 K for both N⁺ density and depth of N⁺ penetration in the Ti sample. The variation of these results with temperature was explained on the basis of the residual gas, substrate temperature, dissociation of water in the chamber and the gettering property of titanium.     

Change of sheet resistance of high purity alumina ceramics implanted by Cu and Ti ions

High purity alumina ceramics (99% Al₂O₃) was implanted by copper ion and titanium ion in a metal vapour vacuum arc (MEVVA) implanter, respectively. The influence of implantation parameters was studied varying ion fluence. The samples were implanted by 68 keV Cu ion and 82 keV Ti ion with fluences from 1 × 10¹⁵ to 1 × 10¹⁸ ions/cm², respectively. The as-implanted samples were investigated by scanning electron microscopy (SEM), glancing X-ray diffraction (GXRD), scanning Auger microscopy (SAM), and four-probe method. Different morphologies were observed on the surfaces of the as-implanted samples and clearly related to implantation parameters. For both ion implantations, the sheet resistances of the alumina samples implanted with Cu and Ti ion fluences of 1 × 10¹⁸ ions/cm², respectively, reached the corresponding minimum values because of the surface metallization. The experimental results indicate that the high-fluence ion implantation resulted in conductive layer on the surface of the as-implanted high purity alumina ceramics.     

Temperature and N energy dependence on nano-structural modifications and characteristics of Mo surface

The surface modifications of Mo massive samples (0.5 mm foils) made by nitrogen ion implantation are studied by SEM, XRD, AFM, and SIMS. Nitrogen ions in the energy range of 16-30 keV with a fluence of 1 × 10¹⁸ N⁺ cm⁻² were implanted in molybdenum samples for 1600 s at different temperatures. XRD patterns clearly showed MoN (0 3 1) (hcp) very close to Mo (2 0 0) line. Crystallite sizes (coherently diffracting domains) obtained from MoN (0 3 1) line, showed an increase with substrate temperature. AFM images showed the formation of grains on Mo samples, which grew in size with temperature. Similar morphological changes to that has been observed for thin films by increasing substrate temperature (i.e., structure zone model (SZM)), is obtained. The density of implanted nitrogen ions and the depth of nitrogen ion implantation in Mo studied by SIMS showed a minimum for N⁺ density as well as a minimum for penetration depth of N⁺ ions in Mo at certain temperatures, which are both consistent with XRD results (i.e., I_{Mo (2 0 0)}/I_{Mo (2 1 1)}) for Mo (bcc). Hence, showing a correlation between XRD and SIMS results. This phenomenon is explained on the basis of residual gas, substrate temperature, dissociation of water in the chamber and the ion energy.     

Surface nano-structural modifications and characteristics in nitrogen ion implanted W as a function of temperature and N energy

The surface modifications of tungsten massive samples (0.5 mm foils) made by nitrogen ion implantation are studied by SEM, XRD, AFM, and SIMS. Nitrogen ions in the energy range of 16-30 keV with a fluence of 1 × 10¹⁸ N⁺ cm⁻² were implanted in tungsten samples for 1600 s at different temperatures. XRD patterns clearly showed WN₂ (0 1 8) (rhombohedral) very close to W (2 0 0) line. Crystallite sizes (coherently diffracting domains) obtained from WN₂ (0 1 8) line, showed an increase with substrate temperature. AFM images showed the formation of grains on W samples, which grew in size with temperature. Similar morphological changes to that has been observed for thin films by increasing substrate temperature (i.e., structure zone model (SZM)), is obtained. The surface roughness variation with temperature generally showed a decrease with increasing temperature. The density of implanted nitrogen ions and the depth of nitrogen ion implantation in W studied by SIMS showed a minimum for N⁺ density as well as a minimum for penetration depth of N⁺ ions in W at certain temperatures, which are both consistent with XRD results (i.e., I_{W (2 0 0)}/I_{W (2 1 1)}) for W (bcc). Hence, showing a correlation between XRD and SIMS results.     

Influence of titanium ions implantation on corrosion behavior of zirconium in 1 M H2SO4

In order to study the effect of titanium ion implantation on the aqueous corrosion behavior of zirconium, specimens were implanted with titanium ions with fluence ranging from 1 × 10¹⁶ to 1 × 10¹⁷ ions/cm², using a metal vapor vacuum arc (MEVVA) source at an extraction voltage of 40 kV. The valence states and depth distributions of elements in the surface layer of the samples were analyzed by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES), respectively. The potentiodynamic polarization technique was employed to evaluate the aqueous corrosion resistance of implanted zirconium in a 1 M H₂SO₄ solution. It was found that a significant improvement was achieved in the aqueous corrosion resistance of zirconium implanted with titanium ions. The larger the fluence, the better is the corrosion resistance of implanted sample. Finally, the mechanism of the corrosion behavior of titanium-implanted zirconium was discussed.     

Modification of medical metals by ion implantation of copper

The effect of copper ion implantation on the antibacterial activity, wear performance and corrosion resistance of medical metals including 317 L of stainless steels, pure titanium, and Ti-Al-Nb alloy was studied in this work. The specimens were implanted with copper ions using a MEVVA source ion implanter with ion doses ranging from 0.5 × 10¹⁷ to 4 × 10¹⁷ ions/cm² at an energy of 80 keV. The antibacterial effect, wear rate, and inflexion potential were measured as a function of ion dose. The results obtained indicate that copper ion implantation improves the antibacterial effect and wear behaviour for all the three medical materials studied. However, corrosion resistance decreases after ion implantation of copper. Experimental results indicate that the antibacterial property and corrosion resistance should be balanced for medical titanium materials. The marked deteriorated corrosion resistance of 317 L suggests that copper implantation may not be an effective method of improving its antibacterial activity.     

Synthesis of molybdenum silicide by both ion implantation and ion beam assisted deposition

Two groups of Mo/Si films were deposited on surface of Si(1 0 0) crystal. The first group of the samples was prepared by both ion beam assisted deposition (IBAD) and metal vapor vacuum arc (MEVVA) ion implantation technologies under temperatures from 200 to 400 °C. The deposited species of IBAD were Mo and Si, and different sputtering Ar ion densities were selected. The mixed Mo/Si films were implanted by Mo ion with energy of 94 keV, and fluence of Mo ion was 5 × 10¹⁶ ions/cm². The second group of the samples was prepared only by IBAD under the same test temperature range. The Mo/Si samples were analyzed by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), sheet resistance, nanohardness, and modulus of the Mo/Si films were also measured. For the Mo/Si films implanted with Mo ion, XRD results indicate that phase of the Mo/Si films prepared at 400 and 300 °C was pure MoSi₂. Sheet resistance of the Mo/Si films implanted with Mo ion was less than that of the Mo/Si films prepared without ion implantation. Nanohardness and modulus of the Mo/Si films were obviously affected by test parameters.     

Structure and micro-mechanical properties of helium-implanted layer on Ti by plasma-based ion implantation

The present paper concentrates on structure and micro-mechanical properties of the helium-implanted layer on titanium treated by plasma-based ion implantation with a pulsed voltage of −30 kV and doses of 3, 6, 9 and 12 × 10¹⁷ ions/cm², respectively. X-ray photoelectron spectroscopy and transmission electron microscopy are employed to characterize the structure of the implanted layer. The hardnesses at different depths of the layer were measured by nano-indentation. We found that helium ion implantation into titanium leads to the formation of bubbles with a diameter from a few to more than 10 nm and the bubble size increases with the increase of dose. The primary existing form of Ti is amorphous in the implanted layer. Helium implantation also enhances the ingress of O, C and N and stimulates the formations of TiO₂, Ti₂O₃, TiO, TiC and TiN in the near surface layer. And the amount of the ingressed oxygen is obviously higher than those of nitrogen and carbon due to its higher activity. At the near surface layer, the hardnesses of all implanted samples increases remarkably comparing with untreated one and the maximum hardness has an increase by a factor of up to 3.7. For the samples implanted with higher doses of 6, 9 and 12 × 10¹⁷ He/cm², the local displacement bursts are clearly found in the load-displacement curves. For the samples implanted with a lower dose of 3 × 10¹⁷ He/cm², there is no obvious displacement burst found. Furthermore, the burst width increases with the increase of the dose.     

Improving the bioactivity of NiTi shape memory alloy by heat and alkali treatment

TiO₂ films were formed on an NiTi alloy surface by heat treatment in air at 600 °C. Heat treated NiTi shape memory alloys were subsequently alkali treated with 1 M, 3 M and 5 M NaOH solutions respectively, to improve their bioactivity. Then treated NiTi samples were soaked in 1.5SBF to evaluate their in vitro performance. The results showed that the 3 M NaOH treatment is the most appropriate method. A large amount of apatite formed within 1 day's soaking in 1.5SBF, after 7 day's soaking TiO₂/HA composite layer formed on the NiTi surface. SEM, XRD, FT-IR and TEM results showed that the morphology and microstructure are similar to the human bone apatite.     

Synthesis of silicon carbide films by combined implantation with sputtering techniques

Silicon carbide (SiC) films were synthesized by combined metal vapor vacuum arc (MEVVA) ion implantation with ion beam assisted deposition (IBAD) techniques. Carbon ions with 40 keV energy were implanted into Si(1 0 0) substrates at ion fluence of 5 × 10¹⁶ ions/cm². Then silicon and carbon atoms were co-sputtered on the Si(1 0 0) substrate surface, at the same time the samples underwent assistant Ar-ion irradiation at 20 keV energy. A group of samples with substrate temperatures ranging from 400 to 600 °C were used to analyze the effect of temperature on formation of the SiC film. Influence of the assistant Ar-ion irradiation was also investigated. The structure, morphology and mechanical properties of the deposited films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and nanoindentation, respectively. The bond configurations were obtained from IR absorption and Raman spectroscopy. The experimental results indicate that microcrystalline SiC films were synthesized at 600 °C. The substrate temperature and assistant Ar-ion irradiation played a key role in the process. The assistant Ar-ion irradiation also helps increasing the nanohardness and bulk modulus of the SiC films. The best values of nanohardness and bulk modulus were 24.1 and 282.6 GPa, respectively.     

Synthesis and characterization of TiO2 thin films coated on metal substrate

Nanostructured titanium dioxide (TiO₂) thin films have been prepared on metal substrates using a facile layer-by-layer dip-coating method. The phase structure and morphologies of preparing samples were characterized by means of X-ray powder diffraction (XRD) and field-emission scanning electron microscopy (FESEM). The results confirm that films are highly crystalline anatase TiO₂ and free from other phases of titanium dioxide. Scanning electron microscopy (SEM) shows that the nanoparticles are sintered together to form a compact structure. The electrical properties of samples were investigated by cutternt-voltage analysis, the result indicates that a rectifying junction between the nanocrystalline TiO₂ film and metal substrate was formed. The photoelectrochemical characteristics recorded under 1.5 AM illumination indicates that the as-fabricated thin film electrode possesses the highest photocurrent density at 450 °C, which is 1.75 mA/cm² at 0 V vs. Ag/AgCl.     

Effect of copper ions implantation on corrosion behavior of zircaloy-4 in 1 M H2SO4

In order to study the effect of copper ion implantation on the aqueous corrosion behavior, samples of zircaloy-4 were implanted with copper ions with fluences ranging from 1 × 10¹⁶ to 1 × 10¹⁷ ions/cm², using a metal vapor vacuum arc source (MEVVA) operated at an extraction voltage of 40 kV. The valence states and depth distributions of elements in the surface layer of the samples were analyzed by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES), respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the copper ion implantation. The potentiodynamic polarization technique was employed to evaluate the aqueous corrosion resistance of implanted zircaloy-4 in a 1 M H₂SO₄ solution. It was found that a significant improvement was achieved in the aqueous corrosion resistance of zircaloy-4 implanted with copper ions when the fluence is smaller than 5 × 10¹⁶ ions/cm². The corrosion resistance of implanted samples declined with increasing the fluence. Finally, the mechanism of the corrosion behavior of copper-implanted zircaloy-4 was discussed.     

Ion implantation induced by Cu ablation at high laser fluence

High energy laser plasma-produced Cu ions have been implanted in silicon substrates placed at different distances and angles with respect to the normal to the surface of the ablated target. The implanted samples have been produced using the iodine high power Prague Asterix Laser System (PALS) using 438 nm wavelength irradiating in vacuum a Cu target. The high laser pulse energy (up to 230 J) and the short pulse duration (400 ps) produced a non-equilibrium plasma expanding mainly along the normal to the Cu target surface. Time-of-flight (TOF) technique was employed, through an electrostatic ion energy analyzer (IEA) placed along the target normal, in order to measure the ion energy, the ion charge state, the energy distribution and the charge state distribution. Ions had a Boltzmann energy distributions with an energy increasing with the charge state. At a laser fluence of the order of 6 × 10⁶ J/cm², the maximum ion energy was about 600 keV and the maximum charge state was about 27+.In order to investigate the implantation processes, Cu depth profiles have been performed with Rutherford backscattering spectrometry (RBS) of 1.5 MeV helium ions, Auger electron spectroscopy (AES) with 3 keV electron beam and 1 keV Ar sputtering ions in combination with scanning electron microscopy (SEM). Surface analysis results indicate that Cu ions are implanted within the first surface layers and that the ion penetration ranges are in agreement with the ion energy measured with IEA analysis.     

Characteristics of surface nano-structural modifications in nitrogen ion implanted W as a function of temperature

The surface modifications of tungsten massive samples (0.5 mm foils) made by nitrogen ion (30 keV; 1 × 10¹⁸ N⁺ cm⁻²) implantation are studied by XRD, AFM, and SIMS. XRD patterns clearly showed WN₂ (0 1 8) (rhombohedral) very close to W (2 0 0) line. Crystallite sizes obtained from WN₂ (0 1 8) line, showed an increase with substrate temperature. AFM images showed the formation of grains on W samples, which grew in size with temperature. These morphological changes are similar to those observed for thin films by increasing substrate temperature (i.e. structure zone model (SZM)). Surface roughness variation with temperature, showed a decrease with increasing temperature. The density of implanted nitrogen ions, and the depth of nitrogen ion implantation in W are studied by SIMS. The results show a minimum for N⁺ density at a certain temperature consistent with XRD results (i.e. I_W (2 0 0)/I_W (2 1 1)). This minimum in XRD results is again similar to that obtained for different thin films by Savaloni et al. [Physica B, 349 (2004) 44; Vacuum, 77 (2005) 245] and Shi and Player [Vacuum, 49 (1998) 257].     

Effect of annealing temperature on luminescence of Eu ions doped nanocrystal zirconia

Effect of annealing temperature on luminescence of Eu³⁺ ions was studied in nanocrystal zirconia prepared by co-precipitation. The XRDs reveal with annealing temperature increasing the tetragonal crystal phase of the samples is stable. The emission spectra show the strong emission at 595 and 604 nm at 394 nm excitation. Under continuous UV (394 nm) irradiation the 604 nm emission intensity changes of the samples show as a function of irradiation time. In addition, the charge-transfer states of the samples are affected by the annealing temperature. These are associated with the defects at/in the surface of the nanocrystalline ZrO₂ with Eu³⁺ ions.     

Effects of annealing temperature on YAG:Ce synthesized by spray-drying method

In this report, YAG:Ce phosphors were synthesized by spray-drying method. The effects of annealing temperature on crystal structure, morphology and photoluminescence property (PL) of as-prepared samples were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and spectrofluorometer, respectively. The XRD patterns showed all the samples are in consistence with a single garnet phase, and the location of strongest peak shifts to smaller angle with increasing the annealing temperature. The SEM micrographs revealed the sample annealed at 1200 °C appears to be a spherical polycrystalline aggregate; as the samples were annealed at 1300?1400 °C, spherical grains obviously grow up; but the sample annealed at over 1400 °C forms an irregular bulk. The emission spectra of samples indicated the PL of samples annealed at 1200?1400 °C improve with increasing the annealing temperature because of the diffusion of Si⁴⁺ ions; whereas the PL of sample annealed at the temperature over 1400 °C decreases likely resulting from inflection effects of multiangular shape of grains. Therefore, the samples annealed at 1400 °C are suitable for gaining phosphor with high brightness and good morphology.     

A green synthetic approach to graphene nanosheets for hydrogen adsorption

A green and facile strategy of preparing graphene by reducing exfoliated graphite oxide (GO) with glucose was developed in this study. The as-prepared samples were characterized by X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Atomic force microscopy (AFM). The characterization results indicated that the graphene sheets (GS) were of high quality with smooth surface, rich pore structure and few layer graphene. The samples have a BET specific surface area of 1205.8 m² g⁻¹ measured by N₂ adsorption at 77 K. The hydrogen storage capacity of 2.7 wt.% at 298 K and 25 bar demonstrated that the as-prepared graphene employing glucose as reductant is supposed to be a promising material with outstanding property for hydrogen storage.     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

Chemical synthesis of nanocrystalline SnO2 thin films for supercapacitor application

Nanocrystalline SnO₂ thin films were deposited by simple and inexpensive chemical route. The films were characterized for their structural, morphological, wettability and electrochemical properties using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy techniques (SEM), transmission electron microscopy (TEM), contact angle measurement, and cyclic voltammetry techniques. The XRD study revealed the deposited films were nanocrystalline with tetragonal rutile structure of SnO₂. The FT-IR studies confirmed the formation of SnO₂ with the characteristic vibrational mode of Sn-O. The SEM studies showed formation of loosely connected agglomerates with average size of 5-10 nm as observed from TEM studies. The surface wettability showed the hydrophilic nature of SnO₂ thin film (water contact angle 9°). The SnO₂ showed a maximum specific capacitance of 66 F g⁻¹ in 0.5 Na₂SO₄ electrolyte at 10 mV s⁻¹ scan rate.     

Luminescent and morphological study of Sr2CeO4 blue phosphor prepared from oxalate precursors

Luminescent and morphological studies of Sr₂CeO₄ blue phosphor prepared from cerium-doped strontium oxalate precursor are reported. Powder samples were prepared from 5 and 25 mol% Ce³⁺-doped strontium oxalate as well as from a mechanical mixture of strontium oxalate and cerium oxalate at a 4:1 ratio, respectively. All the samples were characterized by XRD, IR, PLS, and SEM. The luminescent and structural properties of the Sr₂CeO₄ material are little affected by the SrCO₃ remaining from precursors. The Sr₂CeO₄ material consists in one-dimensional chains of edge-sharing CeO₆ octahedra that are linked together by Sr²⁺ ions. The carbonate ion might be associated with oxygen ions of the linear chain, and also with the oxygen atoms located in the equatorial position, which consequently affects the charge transfer bands between O²⁻ and Ce⁴⁺. As observed by SEM, the morphological changes are related to each kind of precursor and thermal treatment, along with irregular powder particles within the size range 0.5-2 μm.