Laser etching of transparent materials at a backside surface adsorbed layer

The laser etching using a surface adsorbed layer (LESAL) is a new method for precise etching of transparent materials with pulsed UV-laser beams. The influence of the processing parameters to the etch rate and the surface roughness for etching of fused silica, quartz, sapphire, and magnesium fluoride (MgF₂) is investigated. Low etch rates of 1 nm/pulse and low roughness of about 1 nm rms were found for fused silica and quartz. This is an indication that different structural modifications of the material do not affect the etching significantly as long as the physical properties are not changed. MgF₂ and sapphire feature a principal different etch behavior with a higher etch rate and a higher roughness. Both incubation effects as well as the temperature dependence of the etch rate can be interpreted by the formation of a modified near surface region due to the laser irradiation. At repetition rates up to 100 Hz, no changes of the etch rate have been observed at moderate laser fluences.     

Laser processing of micro-optical components in quartz

Laser induced backside wet etching combined with the diffractive gray tone phase mask has been used for the fabrication of a micro-lens array with a single lens diameter of 1 mm and a micro-prism in quartz. The micro-lens array was tested as beam homogenizer for high power XeCl excimer laser yielding a clear improvement in the quality of the laser beam.The optimum fluence range for fabrication of micro-lenses by laser induced backside wet etching using 1.4 M pyrene in THF solution and 308 nm irradiation wavelength is 1-1.6 J/cm². The etching mechanisms of LIBWE are based on a combination of pressure and temperature jumps at quartz-liquid interface.     

Surface plasmon scattering on polymer-bimetal layer covered fused silica gratings generated by laser induced backside wet etching

Large amplitude fused silica gratings are prepared by combining the UV laser induced backside wet etching technique (LIBWE) and the two-beam interference method. The periodic patterning of fused silica surfaces is realized by s-polarized fourth harmonic beams of a Nd:YAG laser, applying saturated solution of naphthalene in methyl-methacrylate as liquid absorber. Atomic force microscopy is utilized to analyze how the modulation amplitude of the grating can be controlled by the fluence and number of laser pulses. Three types of plasmonic structures are prepared by a bottom-up method, post-evaporating the fused silica gratings by gold-silver bimetal layers, spin-coating the metal structures by thin polycarbonate films, and irradiating the multilayers by UV laser. The effect of the bimetal and polymer-coated bimetal gratings on the surface plasmon resonance is investigated in a modified Kretschmann arrangement allowing polar and azimuthal angle scans. It is demonstrated experimentally that scattering on rotated gratings results in additional minima on the resonance curves of plasmons excited by second harmonic beam of a continuous Nd:YAG laser. The azimuthal angle dependence proves that these additional minima originate from back-scattering. The analogous reflectivity minima were obtained by scattering matrix method calculations realized taking modulation depths measured on bimetal gratings into account.     

Time-resolved measurements during backside dry etching of fused silica

The laser-induced backside dry etching (LIBDE) investigated in this study makes use of a thin metal film deposited at the backside of a transparent sample to achieve etching of the sample surface. For the time-resolved measurements at LIBDE fused silica samples coated with 125 nm tin were used and the reflected and the transmitted laser intensities were recorded with a temporal resolution of about 1 ns during the etching with a ∼30 ns KrF excimer laser pulse. The laser beam absorption as well as characteristic changes of the reflection of the target surface was calculated in dependence on the laser fluence in the range of 250-2500 mJ/cm² and the pulse number from the temporal variations of the reflection and the transmission. The decrease of the time of a characteristic drop in the reflectivity, which can be explained by the ablation of the metal film, correlates with the developed thermal model. However, the very high absorption after the film ablation probably results in very high temperatures near the surface and presumably in the formation of an absorbing plasma. This plasma may contribute to the etching and the surface modification of the substrate. After the first pulse a remaining absorption of the sample was measured that can be discussed by the redeposition of portions of the ablated metal film or can come from the surface modification in the fused silica sample. These near-surface modifications permit laser etching with the second laser pulse, too.     

Laser backside etching of fused silica with ultra-short pulses

Laser backside etching of transparent materials like fused silica at the interface to liquids with sub-picosecond UV laser pulses using a pyrene/toluene solution is achieved. For the experimental conditions applied, the etching effect is rather weak with measured rates of the order of 0.1 nm/pulse. A linear dependence of the etched volume upon the laser pulse energy or the pulse number was extracted from the experimental data obtained. At low pulse numbers the etched surface exhibits a feature-free, smooth morphology, while quasi-periodic ripple formation is observed for prolonged laser exposure. In addition, the etching process is accompanied by enhanced carbon deposition at and in the vicinity of the etched surface. The etching mechanism proposed comprises the primary interaction of the laser radiation with the liquid, a surface-modification phase, and the etching of the modified fused-silica surface. PACS 81.65.Cf; 81.05.Kf; 79.20.Ds; 61.80.Ba; 42.55.Lt; 68.45.Da     

Time-resolved transmission study of fused silica during laser-induced backside dry etching

Laser-induced backside dry etching (LIBDE) is a promising technique for micro- and nanomachining of transparent materials. Although several experiments have already proved the suitability and effectiveness of the technique, there are several open questions concerning the etching mechanism and the concomitant processes. In this paper time-resolved light transmission investigations of etching process of fused silica are presented. 125 nm thick silver coating was irradiated through the carrying 1 mm thick fused silica plate by single pulses of a nanosecond KrF excimer laser. The applied fluences were 0.38, 0.71 and 1 J/cm². During the etching process the irradiated spots were illuminated by an electronically delayed nitrogen laser pumped dye laser. The delay between the pump and probe pulses was varied in the range of 0 ns and 20 μs. It was found that the transmitted probe beam intensity strongly depends on the applied delays and fluences. Scanning electron microscopy and energy dispersive X-ray spectrometry of the etched surface showed the existence of silver droplets and fragments on the illuminated surfaces and silver atoms built into the treated surface layer influencing the transmission behavior of the studied samples.     

Laser backside etching of fused silica due to carbon layer ablation

The backside ablation of a absorbing carbon layer onto fused silica is studied in air and water confinement in comparison. The confinement influences the etch rate and the laser fluence dependence of the etch rate significantly while the threshold fluence is almost the same. The different confinement of the laser induced plasma results in the observed rate saturation in the case of air and in a linear growing rate in the case of water confinement at medium laser fluences. The less dense air confinement permits a faster plasma expansion of the laser plume than in the case of water confinement and effects consequently the interaction time and interaction strength of the laser plume with the fused silica surface. The differences in the laser-plasma-substrate interaction cause the observed rate saturation at weak interaction (air) and the growing etch rate at strong interaction (water). Thus, the confinement situation controls the interaction process in the case of backside ablation and should be considered in indirect material processing methods such as LIBWE and LESAL, too. PACS 81.65.C; 81.05.K; 79.20.D; 61.80.B; 42.55.L; 68.45.D     

Influence on the laser induced backside dry etching of thickness and material of the absorber, laser spot size and multipulse irradiation

Laser induced backside dry etching method (LIBDE) was developed - analogously to the well-known laser induced backside wet etching (LIBWE) technique - for the micromachining of transparent materials. In this procedure, the absorbing liquid applied during LIBWE was replaced with solid metal layers. Fused silica plates were used as transparent targets. These were coated with 15-120 nm thick layers of different metals (silver, aluminium and copper). The absorbing films were irradiated by a nanosecond KrF excimer laser beam through the quartz plate. The applied fluence was varied in the 150-2000 mJ/cm² range, while the irradiated area was between 0.35 and 3.6 mm². At fluences above the threshold values, it was found that the metal layers were removed from the irradiated spots and the fused silica was etched at the same time. In our experiments, we investigated the dependence of the main parameters (etch rate and threshold) of LIBDE on the absorption of the different metal layers (silver, copper, aluminium), on the size of the irradiated area, on the film thickness and on the number of processing laser pulses.     

Aluminum thin film enhanced IR nanosecond laser-induced frontside etching of transparent materials

Laser processing of glass is of significant commercial interest for microfabrication of precision optical engineering devices. In this work, a laser ablation enhancement mechanism for microstructuring of glass materials is presented. The method consists of depositing a thin film of aluminum on the front surface of the glass material to be etched. The laser beam modifies the glass material by being incident on this front-side. The influence of ablation fluence in the nanosecond regime, in combination with the deposition of the aluminum layer of various thicknesses, is investigated by determining the ablation threshold for different glass materials including soda-lime, borosilicate, fused silica and sapphire. Experiments are performed using single laser pulse per shot in an air environment. The best enhancement in terms of threshold fluence reduction is obtained for a 16 nm thick aluminum layer where a reduction of two orders of magnitude in the ablation threshold fluence is observed for all the glass samples investigated in this work.     

激光诱导直接化学光刻

本文利用Ar~+激光倍频257.3nm进行扫描蚀刻Si、GaAs和Zn片,获得的最小光刻线宽为1.2μm,给出蚀刻深度与光强/扫描速度的关系曲线等参量,首次利用光刻技术估计卤素自由基的扩散系数、自由路程以及激光聚焦光斑大小,以及观察到阈值现象。     

A Quenched Dye Laser Pumped by a KrF Excimer Laser

ＡＱｕｅｎｃｈｅｄＤｙｅＬａｓｅｒＰｕｍｐｅｄｂｙａＫｒＦＥｘｃｉｍｅｒＬａｓｅｒ￥ＸＵＥＳｈａｏｌｉｎ；ＬＯＵＱｉｈｏｎｇ；ＨＵＡＮＧＨｕｉｊｉｅ；ＤＵＬｏｎｇｌｏｎｇ（ＳｈａｎｇｈａｉＩｎｓｔｉｔｕｔｅｏｆＯｐｔｉｃｓａｎｄＦｉｎｅＭｅｃｈａｎｉ...     

Using IR laser radiation for backside etching of fused silica

Laser-induced backside etching of fused silica with gallium as highly absorbing liquid is demonstrated using pulsed infrared laser radiation. The influences of the laser fluence, the pulse number, and the pulse length on the etch rate and the etched surface topography were studied and the results are compared with these of excimer laser etching. The high reflectivity of the fused silica-gallium interface at IR wavelengths results in the measured high threshold fluences for etching of about 3 J/cm² and 7 J/cm² for 18 ns and 73 ns pulses, respectively. For both pulse lengths the etch rate rises almost linearly with laser fluence and reaches a value of 350 and 300 nm/pulse at a laser fluence of about 12 and 28 J/cm², respectively. The etching process is almost free from incubation processes because etching with the first laser pulse and a constant etch rate were observed. The etched surfaces are well-defined with clear edges and a Gaussian-curved, smooth bottom. A roughness of about 1.5 nm rms was measured by AFM at an etch depth of 0.95 μm. The normalization of the etch rates with respect to the reflectivity and the pulse length results in similar etch rates and threshold fluence for the different pulse widths and wavelengths. It is concluded that etching is a thermal process including the laser heating, the materials melting, and the materials etching by mechanical forces. The backside etching of fused silica with IR-Nd:YAG laser can be a promising approach for the industrial usage of the backside etching of a wide range of materials. PACS 81.65.C; 81.05.J; 79.20.D; 61.80.B; 42.55.L     

Impurities Effect on e-beam-excited KrF Laser

ＩｍｐｕｒｉｔｉｅｓＥｆｅｃｔｏｎｅｂｅａｍｅｘｃｉｔｅｄＫｒＦＬａｓｅｒＦＥＮＧＧｕｏｇａｎｇＧＡＯＪｕｎｓｉＳＨＡＮＹｕｓｈｅｎｇ（ＣｈｉｎａＩｎｓｔｉｔｕｔｅｏｆＡｔｏｍｉｃＥｎｅｒｇｙ，Ｐ．Ｏ．Ｂｏｘ２７５７，Ｂｅｉｊｉｎｇ１０２４１３...     

Transient pressure induced by laser ablation of liquid toluene: toward the understanding of laser-induced backside wet etching

To clarify the initial stage of laser-induced backside wet etching, we directly measured transient pressure upon laser ablation of toluene under KrF excimer laser irradiation by using a fast-response pressure gauge. The propagation time of the pressure peak to the gauge agreed well with the time for the shock wave to reach the gauge on time-resolved images. The peak pressure P decreased slowly with increasing distance d: P=30.4 MPa for d=100 m to P=11.1 MPa for d=1000 m at a fluence F=1.0 Jcm^-2pulse^-1. The initial pressure, estimated to be of the order of 10–200 MPa, impinges on a transparent plate and contributes to the etching. PACS 79.20.Ds; 47.40.Nm; 47.55.Bx; 42.62.Cf; 81.65.Cf     

Fabrication of 550 nm gratings in fused silica by laser induced backside wet etching technique

A series of 550 nm spacing gratings were fabricated in fused silica by laser induced backside wet etching (LIBWE) method using the fourth harmonic of a Q-switched Nd:YAG laser (wavelength: λ = 266 nm; pulse duration: FWHM = 10 ns). During these experiments we used a traditional two-beam interference method: the spatially filtered laser beam was split into two parts, which were interfered at a certain incident angle (2θ = 28°) on the backside surface of the fused silica plate contacting with the liquid absorber (saturated solution of naphthalene-methyl-methacrylate c = 1.85 mol/dm³). We studied the dependence of the quality and the modulation depth of the prepared gratings on the applied laser fluence and the number of laser pulses. The surface of the etched gratings was characterized by atomic force microscope (AFM). The maximum modulation depth was found to be 180-200 nm. Our results proved that the LIBWE procedure is suitable for production of submicrometer sized structures in transparent materials.     

Indirect laser etching of fused silica: Towards high etching rate processing

The indirect laser processing approach (LIBWE) laser-induced backside wet etching allows defined microstructuring of transparent materials at low laser fluences with high quality. The optical and the thermal properties of the solid/liquid interface determine the temperatures and therefore the etching mechanism in conjunction with the dynamic processes at the interface due to the fast heating/cooling rates. The exploration of organic liquid solvents and solutions such as 0.5 M pyrene/toluene results in low etch rates (∼20 nm/pulse). By means of liquid metals as absorber here, demonstrated for gallium (Ga), etch rates up to 600 nm/pulse can be achieved. Regardless of the high etch rates a still smooth surface similar to etching with organic liquid solutions can be observed. A comparative study of the two kinds of absorbing liquids, organic and metallic, investigates the etch rates regarding the fluence and pulse quantity. Thereby, the effect of incubation processes as result of surface modification on the etching is discussed. In contrast to pyrene/toluene solution the metallic absorber cannot decompose and consequently no decomposition products can alter the solid/liquid interface to enhance the absorption for the laser radiation. Hence, incubation can be neglected in the case of the silica/gallium interface so that this system is a suitable model to investigate the primary processes of LIBWE. To prove the proposed thermal etch mechanism an analytical temperature model based on a solution of the heat equation is derived for laser absorption at the silica/gallium interface.     

The influence of laser-induced surface modifications on the backside etching process

Spectroscopic measurements in the UV/VIS region show reduced transmission through laser-induced backside wet etching (LIBWE) of fused silica. Absorption coefficients of up to 10⁵ cm⁻¹ were calculated from the transmission measurements for a solid surface layer of about 50 nm. The temperatures near the interface caused by laser pulse absorption, which were analytically calculated using a new thermal model considering interface and liquid volume absorption, can reach 10⁴ K at typical laser fluences. The high absorption coefficients and the extreme temperatures give evidence for an ablation-like process that is involved in the LIBWE process causing the etching of the modified near-surface region. The confinement of the ablation/etching process to the modified near-surface material region can account for the low etch rates observed in comparison to front-side ablation.     

10 ps High Power Laser System at 248 nm

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓｔｈｅｒｅｈａｓｂｅｅｎａｎｉｎｔｅｎｓｉｖｅｅｆｆｏｒｔｄｉｒｅｃｔｅｄｔｏｗａｒｄｔｈｅｐｒｏｄｕｃｔｉｏｎｏｆｓｈｏｒｔｐｕｌｓｅ,ｈｉｇｈ ｐｏｗｅｒＵＶｌａｓｅｒｓｙｓｔｅｍｓ .ＫｒＦｌａｓｅｒ,ｗｉｔｈｉｔｓ～ 2ｎｍｂａｎｄｗｉｄｔｈ ,ｈｉｇｈｅｌｅｃｔｒｉｃａｌ ｔｏ ｏｐｔｉｃａｌｃｏｎｖｅｒｓｉｏｎｅｆｆｉｃｉｅｎｃｙａｎｄｉｔｓｕｎｂｏｕｎｄ ｇｒｏｕｎｄｓｔａｔｅ ,ｉｓａｎａｔｔｒａｃｔｉｖｅｃａｎｄｉｄａｔｅｆｏｒｔｈｅ…     

Laser-induced backside wet etching of fluoride and sapphire using picosecond laser pulses

Laser-induced backside wet etching (LIBWE) is a promising process for microstructuring of rigid chemical resistant and inert transparent materials. LIBWE with nanosecond laser pulses has been successfully demonstrated in a number of studies. LIBWE in a time scale of femtosecond and picosecond pulse durations has been investigated only in a few studies and just on fused silica. In the present study LIBWE of fluorides (CaF₂, MgF₂) and sapphire with a mode-locked picosecond (t _p=10 ps) laser at a UV wavelength of λ=355 nm using toluene as absorbing liquid has been demonstrated. The influence of the laser fluence and the pulse number on the etching rate and the achieved surface morphology was investigated. The etching rate grows linearly with the laser fluence in the low and high-fluence ranges with different slopes. The achieved etching rates for CaF₂ and for sapphire were in the same range. Contrary to CaF₂ and sapphire the etching rates of MgF₂ were one magnitude less. For backside etching on sapphire at high fluences smooth surfaces and at low fluences ripples pattern were found, whereas fluoride surfaces showed a trend towards crack formation.     

Micromachining of quartz crystal with excimer lasers by laser-induced backside wet etching

We fabricated a well-defined pattern of lines and spaces on the surface of a quartz crystal plate (c-SiO₂) with micron-sized features, using laser-induced backside wet etching (LIBWE). The line patterns obtained using LIBWE showed a high aspect ratio of about 3. The etch rates of fused silica (a-SiO₂) ranged from 5 to 25 nm/pulse with KrF laser irradiation from 0.4-1.3 J/cm². Threshold fluences for a-SiO₂ and c-SiO₂ were 0.23 and 0.34 J/cm², respectively. The single-pulse etch depth was not affected by the repetition rates of laser pulses from 1-50 Hz.