Prediction of lateral barrier height in identically prepared Ni/n-type GaAs Schottky barrier diodes

We have identically prepared Ni/n-GaAs/In Schottky barrier diodes (SBDs) with doping density of 7.3 × 10¹⁵ cm⁻³. The barrier height for the Ni/n-GaAs/In SBDs from the current-voltage characteristics have varied from 0.835 to 0.856 eV, and ideality factor n from 1.02 to 1.08. We have determined a lateral homogeneous barrier height value of 0.862 eV for the Ni/n-GaAs/In SBD from the experimental linear relationship between barrier heights and ideality factors.     

The effects of annealing on Au/pyronine-B/MD n-InP Schottky structure

Thin film of non-polymeric organic compound pyronine-B has been fabricated on moderately doped (MD) n-InP substrate as an interfacial layer using spin coating technique for the electronic modification of Au/MD n-InP Schottky contact. The electrical characteristics have been determined at room temperature. The barrier height and the ideality factor values for Au/pyronine-B/MD n-InP Schottky diode have been obtained from the forward bias I-V characteristics at room temperature as 0.60 eV and 1.041; 0.571 and 1.253 eV after annealing at 100 and 250 °C, respectively. An increase in annealing temperature at the Au/n-InP Schottky junction is shown to increase the reverse bias leakage current by about one order of magnitude and decrease the Schottky barrier height by 0.027 eV. Furthermore, the barrier height values for the Au/pyronine-B/MD n-InP Schottky diode have also been obtained from the C-V characteristics at room temperature as 1.001 and 0.709 eV after annealing at 100 and 250 °C, respectively. Finally, it was seen that the diode parameters changed with increase in the annealing temperature.     

The importance of the series resistance in calculating the characteristic parameters of the Schottky contacts

Cd/p-Si Schottky barrier diodes (SBDs) with and without the native oxide layer have been fabricated to determine the importance of the fact that the series resistance value is considered in calculating the interface state density distribution (ISDD) from the forward bias current-voltage (I-V) characteristics of the Cd/p-Si SBDs. The statistical analysis yielded mean values of 0.71 ± 0.02 eV and 1.24 ± 0.12 for the BH and ideality factor of the Cd/p-Si SBDs (15 dots) without the native oxide layer (MS), respectively, and mean values of 0.79 ± 0.02 eV and 1.36 ± 0.06 eV for the Cd/p-Si SBDs (28 dots) with the native oxide layer (metal-insulating layer-semiconductor (MIS)). The interface state density (Nss) distributions of the devices were calculated taking into account their series resistance values. At the same energy position near the top of the valence band, the interface state density values without taking into account the series resistance value of the devices are almost one order of magnitude larger than Nss obtained taking into account series resistance value.     

Influence of surface cleaning effects on properties of Schottky diodes on 4H-SiC

Ir/4H-SiC and IrO₂/4H-SiC Schottky diodes are reported in terms of different methods of surface pretreatment before contact deposition. In order to find the effect of surface preparation processes on Schottky characteristics the SiC wafers were respectively cleaned using the following processes: (1) RCA method followed by buffered HF dip. Next, the surface was oxidized (5.5 nm oxide) using a rapid thermal processing reactor chamber and circular geometry windows were opened in the oxide layer before metallization deposition; (2) the same as sequence (1) but with an additional in situ sputter etching step before metallization deposition; (3) cleaning in organic solvents followed by buffered HF dip. The I-V characteristics of Schottky diodes were analyzed to find a correlation between extracted parameters and surface treatment. The best results were obtained for the sequence (1) taking into account theoretical value of Schottky barrier height. The contacts showed excellent Schottky behavior with ideality factors below 1.08 and barrier heights of 1.46 eV and 1.64 eV for Ir and IrO₂, respectively. Very promising results were obtained for samples prepared using the sequence (2) taking into account the total static power losses because the modified surface preparation results in a decrease in the forward voltage drop and reverse leakage current simultaneously. The contacts with ideality factor below 1.09 and barrier height of 1.02 eV were fabricated for Ir/4H-SiC diodes in sequence (2).     

Current transport mechanism in Al/Si3N4/p-Si (MIS) Schottky barrier diodes at low temperatures

The current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-insulator-semiconductor (Al/Si₃N₄/p-Si) Schottky barrier diodes (SBDs) were measured in the temperature range of 80-300 K. By using the thermionic emission (TE) theory, the zero-bias barrier height Φ_B0 calculated from I-V characteristics was found to increase with increasing temperature. Such temperature dependence is an obvious disagreement with the negative temperature coefficient of the barrier height calculated from C-V characteristics. Also, the ideality factor decreases with increasing temperature, and especially the activation energy plot is nonlinear at low temperatures. Such behaviour is attributed to Schottky barrier inhomogeneties by assuming a Gaussian distribution of barrier heights (BHs) at interface. We attempted to draw a Φ_B0 versus q/2kT plot to obtain evidence of a Gaussian distribution of the BHs, and the values of Φ_Bo = 0.826 eV and α_o = 0.091 V for the mean barrier height and standard deviation at zero-bias, respectively, have been obtained from this plot. Thus, a modified ln(I_o/T²) − q²σ_o²/2(kT)² versus q/kT plot gives Φ_B0 and Richardson constant A^* as 0.820 eV and 30.273 A/cm² K², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 30.273 A/cm² K² is very close to the theoretical value of 32 A/cm² K² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/Si₃N₄/p-Si Schottky barrier diodes can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights. In addition, the temperature dependence of energy distribution of interface state density (N_SS) profiles was determined from the forward I-V measurements by taking into account the bias dependence of the effective barrier height and ideality factor.     

Laterally inhomogeneous barrier analysis of the methyl violet/p-Si organic/inorganic hybrid Schottky structures

In this work, we have investigated the electrical characteristics, such as current-voltage (I-V) and capacitance-voltage (C-V) measurements, of identically prepared crystal violet/p-Si Organic/Inorganic (OI) Schottky structures formed by evaporation of organic compound solution to directly p-Si semiconductor substrate. It has been seen that the crystal violet organic dye thin film on the p-Si substrate has exhibited a good rectifying behavior. The barrier heights (BHs) and ideality factors of all devices have been calculated from the electrical characteristics. Although the diodes were all identically prepared, there was a diode-to-diode variation: the effective barrier heights ranged from 0.6 ± 0.1 to 0.8 ± 0.1 eV, and the ideality factor from 1.6 ± 0.4 to 3.5 ± 0.4. The barrier height versus ideality factor plot has been plotted for the OI devices. Lateral homogeneous BH was calculated as a value of 0.7 eV from the observed linear correlation between BH and ideality factor, which can be explained by laterally inhomogeneities of BHs. The values of barrier height and acceptor doping concentration yielded from the reverse bias C-V measurements ranged from 0.7 ± 0.1 to 1.3 ± 0.1 eV and from (4.7 ± 0.8) × 10¹⁴ to (8.1 ± 0.8) × 10¹⁴ cm⁻³, respectively. The mean barrier height and mean acceptor doping concentration from C-V characteristics has been calculated 1.0 eV and 5.9 × 10¹⁴ cm⁻³, respectively. It has been seen that the mean BH value of 0.7 eV obtained for the Al/methyl violet/p-Si contact is significantly larger than BH values of the conventional Al/p-Si Schottky diodes. Thus, modification of the interfacial potential barrier for metal/Si diodes has been achieved using a thin interlayer of the methyl violet organic semiconductor; this has been ascribed to the fact that the methyl violet interlayer increases the effective barrier height by influencing the space charge region of Si.     

The barrier height inhomogeneity in Al/p-Si Schottky barrier diodes with native insulator layer

The current-voltage (I-V) characteristics of Al/p-Si Schottky barrier diodes (SBDs) with native insulator layer were measured in the temperature range of 150-375 K. The estimated zero-bias barrier height Φ_B0 and the ideality factor n assuming thermionic emission (TE) theory show strong temperature dependence. Evaluation of the forward I-V data reveals an increase of zero-bias barrier height Φ_B0 but decrease of ideality factor n with increase in temperature. The conventional Richardson plot exhibits non-linearity below 250 K with the linear portion corresponding to activation energy of 0.41 eV and Richardson constant (A^*) value of 1.3 × 10⁻⁴ A cm⁻² K⁻² is determined from intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 A cm² K² for holes in p-type Si. Such behavior is attributed to Schottky barrier inhomogene ties by assuming a Gaussian distribution of barrier heights (BHs) due to barrier height inhomogeneities that prevail at interface. Also, Φ_B0 versus q/2kT plot was drawn to obtain evidence of a Gaussian distribution of the BHs, and values of Φ_B0 = 1.055 eV and σ₀ = 0.13 V for the mean BH and zero-bias standard deviation have been obtained from this plot, respectively. Thus, the modified versus q/kT plot gives Φ_B0 and A^* as 1.050 eV and 40.08 A cm⁻² K⁻², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 40.03 A cm⁻² K⁻² is very close to the theoretical value of 32 A K⁻² cm⁻² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/p-Si Schottky barrier diodes with native insulator layer can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights.     

Barrier height enhancement and temperature dependence of the electrical characteristics of Al Schottky contacts on p-GaAs with organic Rhodamine B interfacial layer

In this work, two types of Schottky barrier diodes (SBDs) with and without Rhodamine B interfacial layer, were fabricated and measured at room temperature in order to investigate the effects of the Rhodamine B interfacial layer on the main electrical parameters. It was seen that the barrier height (BH) value of 0.78 eV calculated for the Al/Rhodamine B/p-GaAs device was higher than the value of 0.63 eV of the conventional Al/p-GaAs Schottky diodes. It has been observed that the Rhodamine B film increases the effective BH by influencing the space charge region of GaAs. The main diode parameters such as the ideality factor (n) and zero-bias BH of SBD with Rhodamine B interfacial layer were found to be strongly temperature dependent and while the BH decreases, the ideality factor increases with decreasing temperature. It has been concluded that the temperature dependent characteristic parameters for Al/Rhodamine B/p-GaAs SBDs can be successfully explained on the basis of thermionic emission (TE) mechanism with Gaussian distribution of the barrier heights.     

Effect of annealing on the electronic parameters of Au/poly(ethylmethacrylate)/n-InP Schottky diode with organic interlayer

A thin poly(ethylmethacrylate) (PEMA) layer is deposited on n-InP as an interlayer for electronic modification of Au/n-InP Schottky structure. The electrical properties of Au/PEMA/n-InP Schottky diode have been investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements at different annealing temperatures. Experimental results show that Au/PEMA/n-InP structure exhibit a good rectifying behavior. An effective barrier height as high as 0.83 eV (I–V) and 1.09 eV (C–V) is achieved for the Au/PEMA/n-InP Schottky structure after annealing at 150 °C compared to the as-deposited and annealed at 100 and 200 °C. Modified Norde's functions and Cheung method are also employed to calculate the barrier height, series resistance and ideality factors. Results show that the barrier height increases upon annealing at 150 °C and then slightly decreases after annealing at 200 °C. The PEMA layer increases the effective barrier height of the structure as this layer creates a physical barrier between the Au metal and the n-InP. Terman's method is used to determine the interface state density and it is found to be 5.141 × 10¹² and 4.660 × 10¹² cm^?2 eV^?1 for the as-deposited and 200 °C annealed Au/PEMA/n-InP Schottky diodes. Finally, it is observed that the Schottky diode parameters change with increasing annealing temperature.     

Effects of chemical treatment on barrier height and ideality factors of Au/GaN Schottky diodes

We have studied Au/n-GaN Schottky barrier diodes. GaN surfaces have been prepared by cleaning in HCl and (NH₄)₂S prior to metal deposition. The zero-biased barrier heights and ideality factors obtained from the current-voltage characteristics differ from diode to diode, although all the samples were prepared identically. The statistical analysis for the reverse bias C-V data yielded mean value of (1.35±0.04) eV for Schottky barrier height of HCl treated sample and (1.20±0.03) eV for (NH₄)₂S sample, where 9 dots were considered from each cleaning method. It was found that the barrier height values obtained from the C⁻²-V (1.43 eV) and I-V characteristics (0.89 eV) are different from each other by 0.54 eV. The inhomogeneous barrier heights were found to be related to the effect of the high series resistance on diode parameters (Akkiliç et al., 2004) [1].     

Effect of surface preparation on the properties of Au/p-Cd1−xZnxTe

The effect of bromine methanol (BM) etching and NH₄F/H₂O₂ passivation on the Schottky barrier height between Au contact and semi-insulated (SI) p-Cd_1−xZn_xTe (x ≈ 0.09-0.18) was studied through current-voltage (I-V) and capacitance-voltage (C-V) measurements. Near-infrared (NIR) spectroscopy technique was utilized to determine the Zn concentration. X-ray photoelectron spectroscopy (XPS) for surface composition analysis showed that BM etched sample surface left a Te⁰-rich layer, however, which was oxidized to TeO₂ and the surface [Te]/([Cd] + [Zn]) ratio restored near-stoichiometry after NH₄F/H₂O₂ passivation. According to I-V measurement, barrier height was 0.80 ± 0.02-0.85 ± 0.02 eV for Au/p-Cd_1−xZn_xTe with BM etching, however, it increased to 0.89 ± 0.02-0.93 ± 0.02 eV with NH₄F/H₂O₂ passivation. Correspondingly, it was about 1.34 ± 0.02-1.43 ± 0.02 eV and 1.41 ± 0.02-1.51 ± 0.02 eV by C-V method.     

Electrical and structural properties of a stacked metal layer contact to n-InP

In this study, we found that the double metal contact structure in Pt/Al/n-InP diodes provides better rectification characteristics than conventional single-metal/n-InP Schottky diodes. The effective barrier height was measured to be 0.67 eV for a 400 °C-annealed Pt/Al/n-InP diode sample. The increase in the barrier height is attributed to the formation of Al₂O₃ at the metal/n-InP contact interface during thermal annealing. The formation of the phase Al₂O₃ phase was monitored by X-ray diffraction (XRD) analysis. The corresponding element profiles of Al and O were also confirmed at the metal/n-InP contact interface using secondary ion mass spectrum (SIMS) analysis. The lowering of the Schottky barrier height due to the inhomogeneity at the metal/n-InP junction is also discussed on the basis of the TE theory. The distribution of local effective Schottky barrier heights was explained by a model incorporating the existence of double Gaussian barrier heights, which represent the high barrier and low barrier of the full distribution in the temperature ranges of 83-198 and 198-300 K.     

PdSi based ohmic contact on n-InP

The electrical and microstructural properties of the PdSi based ohmic contacts on n-InP are discussed in the research. A low specific contact resistance of 2.25 × 10⁻⁶ Ω cm² is obtained on Au/Si/Pd/n-InP contact after rapid thermal annealing (RTA) at 450 °C for 30 s. The low contact resistance can be maintained at the order of 10⁻⁶ Ω cm² even up to 500 °C annealing. From the Auger analysis, it is found that both the outdiffusion of In and the indiffusion of Si into the InP surface occurred at the ohmic contact sample. The formation of the Pd₃Si compound lowered the barrier of the contact. The reactions between Pd and InP of the contact, forming In vacancies, and leading the doping of Si to the InP contact interface.     

Determination of the laterally homogeneous barrier height of thermally annealed and unannealed Au/p-InP/Zn-Au Schottky barrier diodes

We have identically prepared Au/p-InP Schottky barrier diodes (SBDs). The diodes were annealed up to 400 °C thermally. The barrier height (BH) for the as-deposited Au/p-InP/Zn-Au SBDs from the current-voltage characteristics have varied from 0.58 to 0.72 eV, and ideality factor n from 1.14 to 1.47. The BH for the annealed SBDs from the current-voltage characteristics have varied from 0.76 to 0.82 eV, and ideality factor n from 1.17 to 1.39. As a result of the thermal annealing, it has been seen that the BH values of the annealed SBDs are larger than those of the as-deposited SBDs. We have determined a lateral homogeneous BH value of 0.72 eV for the as-deposited Au/p-InP SBD from the experimental linear relationship between barrier heights and ideality factors, and a value of 0.85 eV for the annealed Au/p-InP SBD. The increase of 0.13 eV in the BH value by means of 400 °C annealing has been ascribed to the formation of the excess charges that electrically actives on the semiconductor surface.     

Improved GaSb surfaces using a (NH4)2S/(NH4)2S04 solution

Bulk (1 0 0) n-GaSb surfaces have been treated with a sulphur based solution ((NH₄)₂S/(NH₄)₂SO₄) to which sulphur has been added, not previously reported for the passivation of GaSb surfaces. Au/n-GaSb Schottky barrier diodes (SBDs) fabricated on the treated material show significant improvement compared to that of the similar SBDs on the as-received material as evidenced by the lower ideality factor (n), higher barrier height (?_b) and lower contact resistance obtained. Additionally, the reverse leakage current, although not saturating, has been reduced by almost an order of magnitude at −0.2 V. The sample surfaces were studied by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The native oxide, Sb–O, present on the as-received material is effectively removed on treating with ([(NH₄)₂S/(NH₄)₂SO₄]+S) and (NH₄)₂S. Analysis of the as-received surface by XPS, prior to and after argon sputtering, suggests that the native oxide layer is ≤8.5 nm.     

Electronic properties of the metal/organic interlayer/inorganic semiconductor sandwich device

In this study, we prepared a Metal(Al)/Organic Interlayer(Congo Red=CR)/Inorganic Semiconductor (p-Si) (MIS) Schottky device formed by coating of an organic film on p-Si semiconductor wafer. The Al/CR/p-Si MIS device had a good rectifying behavior. By using the forward bias I-V characteristics, the values of ideality factor (n) and barrier height (Φ_b) for the Al/CR/p-Si MIS device were obtained as 1.68 and 0.77 eV, respectively. It was seen that the Φ_b value of 0.77 eV calculated for the Al/CR/p-Si MIS device was significantly higher than value of 0.50 eV of the conventional Al/p-Si Schottky diodes. Modification of the interfacial potential barrier of the Al/p-Si diode was achieved by using a thin interlayer of the CR organic material. This was attributed to the fact that the CR organic interlayer increased the effective barrier height by influencing the space charge region of Si. The interface-state density of the MIS diode was found to vary from 1.24×10¹³ to 2.44×10¹² eV⁻¹ cm⁻².     

Current-voltage characteristics of Au/GaN/GaAs structure

Au/GaN/n-GaAs structure has been fabricated by the electrochemically anodic nitridation method for providing an evidence of achievement of stable electronic passivation of n-doped GaAs surface. The change of the electronic properties of the GaAs surface induced by the nitridation process has been studied by means of current-voltage (I-V) characterizations on Schottky barrier diodes (SBDs) shaped on gallium nitride/gallium arsenide structure. Au/GaN/n-GaAs Schottky diode that showed rectifying behavior with an ideality factor value of 2.06 and barrier height value of 0.73 eV obeys a metal-interfacial layer-semiconductor (MIS) configuration rather than an ideal Schottky diode due to the existence of GaN at the Au/GaAs interfacial layer. The formation of the GaN interfacial layer for the stable passivation of gallium arsenide surface is investigated through calculation of the interface state density N_ss with and without taking into account the series resistance R_s. While the interface state density calculated without taking into account R_s has increased exponentially with bias from 2.2×10¹² cm⁻² eV⁻¹ in (E_c−0.48) eV to 3.85×10¹² cm⁻² eV⁻¹ in (E_c−0.32) eV of n-GaAs, the N_ss obtained taking into account the series resistance has remained constant with a value of 2.2×10¹² cm⁻² eV⁻¹ in the same interval. This has been attributed to the passivation of the n-doped GaAs surface with the formation of the GaN interfacial layer.     

Temperature dependent electrical characteristics of Sn/p-Si Schottky diodes

Current-voltage and capacitance-voltage characteristics of Sn/p-Si Schottky diodes measured in the temperature range 80-320 K are presented and analysed. Anomalous strong temperature dependencies of the ideality factor and apparent barrier height were obtained. There was also a considerable difference between the apparent barrier heights obtained from current-voltage and capacitance-voltage characteristics. These anomalies are explained by the domination of the current by a high level of thermionic-field emission, and by the presence of deep levels near the Sn/Si interface, which yield a reduction of free hole concentration and a significant temperature dependence of the charge stored near the metal-semiconductor (MS) interface. The evaluation of temperature dependence of forward current for thermionic-field emission resulted in the following parameters: characteristic energy E₀₀ = 9.8 meV, Schottky barrier height at zero bias Φ_b0 = 0.802 eV, bias coefficient of barrier height β = 0, and effective Richardson constant A* = 37.32 A cm⁻² K⁻².     

Temperature-dependent optical absorption measurements and Schottky contact behavior in layered semiconductor n-type InSe(:Sn)

The layered n-InSe(:Sn) single crystal samples have been cleaved from a large crystal ingot grown from non-stoichiometric melt by the Bridgman-Stockbarger method. It has been made the absorption measurements of these samples without Schottky contact under electric fields of 0.0 and 6000 V cm⁻¹. The band gap energy value of the InSe:Sn has been calculated as 1.36 ± 0.01 eV (at 10 K) and 1.28 ± 0.01 eV (at 300 K) under zero electrical field, and 1.31 ± 0.01 eV (at 10 K) and 1.26 ± 0.01 eV (at 300 K) under 6000 Vcm⁻¹. The current-voltage (I-V) characteristics of Au-Ge/InSe(:Sn)/In Schottky diodes have been measured in the temperature range 80-320 K with a temperature step of 20 K. An experimental barrier height (BH) Φ_ap value of about 0.70 ± 0.01 eV was obtained for the Au-Ge/InSe(:Sn)/In Schottky diode at the room temperature (300 K). An abnormal decrease in the experimental BH Φ_b and an increase in the ideality factor n with a decrease in temperature have been explained by the barrier inhomogeneities at the metal-semiconductor interface. From the temperature-dependent I-V characteristics of the Au-Ge/InSe(:Sn)/In contact, that is, and A^* as 0.94 ± 0.02 and 0.58 ± 0.02 eV, and 27 ± 2 and 21 ± 1 (A/cm² K²), respectively, have been calculated from a modified versus 1/T plot for the two temperature regions. The Richardson constant values are about two times larger than the known value of 14.4 (A/cm² K²) known for n-type InSe. Moreover, in the temperature range 80-320 K, we have also discussed whether or not the current through the junction has been connected with TFE.     

Study of Ni/Si(1 0 0) solid-state reaction with Al addition

The characteristics of Ni/Si(1 0 0) solid-state reaction with Al addition (Ni/Al/Si(1 0 0), Ni/Al/Ni/Si(1 0 0) and Al/Ni/Si(1 0 0)) is studied. Ni and Al films were deposited on Si(1 0 0) substrate by ion beam sputtering. The solid-state reaction between metal films and Si was performed by rapid thermal annealing. The sheet resistance of the formed silicide film was measured by four-point probe method. The X-ray diffraction (XRD) was employed to detect the phases in the silicide film. The Auger electron spectroscopy was applied to reveal the element profiles in depth. The influence of Al addition on the Schottky barrier heights of the formed silicide/Si diodes was investigated by current-voltage measurements. The experimental results show that NiSi forms even with the addition of Al, although the formation temperature correspondingly changes. It is revealed that Ni silicidation is accompanied with Al diffusion in Ni film toward the film top surface and Al is the dominant diffusion species in Ni/Al system. However, no Ni_xAl_y phase is detected in the films and no significant Schottky barrier height modulation by the addition of Al is observed.