Room temperature chemical synthesis of lead selenide thin films with preferred orientation

Room temperature chemical synthesis of PbSe thin films was carried out from aqueous ammoniacal solution using Pb(CH₃COO)₂ as Pb²⁺ and Na₂SeSO₃ as Se²⁻ ion sources. The films were characterized by a various techniques including, X-ray diffraction (XRD), energy dispersive X-ray analysis (EDAX), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HR-TEM), selected area electron diffraction (SAED), Fast Fourier transform (FFT) and UV-vis-NIR techniques. The study revealed that the PbSe thin film consists of preferentially oriented nanocubes with energy band gap of 0.5 eV.     

Structural and electrical properties of zinc oxides thin films prepared by thermal oxidation

We report on zinc oxide (ZnO) thin films (d = 55-120 nm) prepared by thermal oxidation, at 623 K, of metallic zinc films, using a flash-heating method. Zinc films were deposited in vacuum by quasi-closed volume technique onto unheated glass substrates in two arrangements: horizontal and vertical positions relative to incident vapour. Depending on the preparation conditions, both quasi-amorphous and (0 0 2) textured polycrystalline ZnO films were obtained. The surface morphologies were characterized by atomic force microscopy and scanning electron microscopy. By in situ electrical measurements during two heating-cooling cycles up to a temperature of 673 K, an irreversible decrease of electrical conductivity of as flash-oxidized Zn films was revealed. The influence of deposition arrangement and oxidation conditions on the structural, morphological and electrical properties of the ZnO films is discussed.     

Structural and optical properties of thermal evaporated magnesium phthalocyanine (MgPc) thin films

X-ray powder diffraction (XRD) of MgPc indicated that the material in the powder form is polycrystalline with monoclinic structure. Miller indices, h k l, values for each diffraction peak in XRD spectrum were calculated. Thermal evaporation technique was used to deposit MgPc thin films. The XRD studies were carried out for MgPc thin films where the results confirm the amorphous nature for the as-deposited films. While, polycrystalline films orientated preferentially to (1 0 0) plane with an amorphous background were obtained for films annealed at 623 K for 3 h. Optical properties of MgPc thin films were characterised by using spectrophotometric measurements of transmittance and reflectance in the spectral range from 190 to 2500 nm. The refractive index, n, and the absorption index, k, were calculated. According to the analysis of dispersion curves, the parameters, namely; the optical absorption coefficient (α), molar extinction coefficient (?_molar), oscillator energy (E_os), oscillator strength (f), and electric dipole strength (q²) were also evaluated. The recorded absorption measurements in the UV-vis region show two well defined absorption bands of phthalocyanine molecule; namely the Q-band and the Soret (B-band). The Q-band showed its splitting characteristic (Davydov splitting), and ΔQ was obtained as 0.15 eV. The analysis of the spectral behaviour of the absorption coefficient (α), in the absorption region revealed indirect transitions. The transport and the near onset energy gaps were estimated as respectively 2.74 ± 0.02 and 1.34 ± 0.01 eV.     

Versatile synthesis of rectangular shaped nanobat-like CuO nanostructures by hydrothermal method; structural properties and growth mechanism

This paper describes a simple and versatile method for growing highly anisotropic rectangular shaped nanobat-like CuO nanostructures by simple, low temperature and cost effective hydrothermal method. Field emission scanning electron microscopy illustrated that these CuO nanostructures have diameter of ∼70 nm, thickness of ∼8 nm and length of ∼174 nm. Structural analysis reveals that the CuO nanostructures have a high crystal quality with monoclinic crystal structure. X-ray photoelectron spectroscopy studies demonstrate that the sample is composed of CuO. The Raman study also indicates the single phase property and high crystallinity of as-grown CuO nanostructures. The plausible growth mechanism for the formation of nanobat-like CuO structure is proposed.     

Cathodoluminescence and structural studies of nitrided 3D gallium structures grown by MOCVD

Cathodoluminescence (CL) spectrum imaging and grazing incidence X-ray diffraction (GIXRD) are employed to investigate nitride three-dimensional (3D) gallium structures. The metallic precursors are naturally obtained on a large variety of substrates by metal-organic chemical vapor deposition (CVD) with different shape/size controlled by the growth conditions, especially the temperature. These 3D metallic structures are subsequently exposed to a nitridation process in a conventional CVD reactor to form GaN nanocrystals, as confirmed by GIXRD measurements. CL spectroscopy shows visible light emission (2.5-2.8 eV) excited from the GaN in the 3D structures.     

Effect of aging time of ZnO sol on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method and the effect of aging time of ZnO sol on the structural and optical properties of the films was studied. The structural characteristics of the samples were analyzed by an atomic force microscope and an X-ray diffractometer. The optical properties were studied by a UV-vis spectrophotometer and a fluorophotometer. The results show that the ZnO thin film prepared by the as-synthesized ZnO sol had relatively poor crystalline quality, low optical transmittance in the visible range and relatively weak ultraviolet emission performance. After the as-synthesized ZnO sol was aged for 24 h, the degree of the preferred crystal orientation along the c-axis of the ZnO thin film prepared by this aged sol was improved. At the same time, this film had a very smooth surface with uniform grains and both its visible range transmittance and ultraviolet emission intensity were obviously increased. These results suggest that appropriate aging of ZnO sol is very important for the improvement of structural and optical quality of ZnO thin films derived from sol-gel method.     

Influence of annealing temperature on the properties of ZnO thin films deposited by thermal evaporation

ZnO thin films were deposited by thermal evaporation of a ZnO powder. The as-deposited films are dark brown, rich zinc and present a low transmittance. Then, these films were annealed in air atmosphere at different temperatures between 100 and 400 °C. Their microstructure and composition were studied using XRD and RBS measurements respectively. By increasing the temperature, it was found that film oxidation starts at 250 °C. XRD peaks related to ZnO appear and peaks related to Zn decrease. At 300 °C, zinc was totally oxidised and the films became totally transparent. The electrical conductivity measurement that were carried out in function of the annealing temperature showed the transition from highly conductive Zn thin film to a lower conductive ZnO thin film. The optical gap (E_g) was deduced from the UV-vis transmittance, and its variation was linked to the formation of ZnO.     

Electrical transport properties of thermally evaporated phthalocyanine (H2Pc) thin films

Thin films of H₂Pc of various thicknesses have been deposited onto glass substrates using thermal evaporation technique at room temperature. The dark electrical resistivity measurements were carried out at different temperatures in the range 298-473 K. An estimation of mean free path (l_o) of charge carriers in H₂Pc thin films was attempted. Measurements of thermoelectric power confirm that H₂Pc thin films behave as a p-type semiconductor. The current density-voltage characteristics of Au/H₂Pc/Au at room temperature showed ohmic conduction mechanism at low voltages. At higher voltages the space-charge-limited conduction (SCLC) accompanied by an exponential trap distribution was dominant. The temperature dependence of current density allows the determination of some essential parameters such as the hole mobility (μ_h), the total trap concentration (N_t), the characteristic temperature (T_t) and the trap density P(E).     

Growth of InN films on spinel substrates by pulsed laser deposition

We have grown InN films on MgAl₂O₄(111) substrates with atomically flat surfaces using pulsed laser deposition (PLD) and compared their structural properties with those grown on (Mn,Zn)Fe₂O₄(111) substrates. It has been revealed that InN(0001) films grow on MgAl₂O₄(111) with an in‐plane epitaxial relationship of InN[1 00] // MgAl₂O₄[1 0], achieving a lattice mismatch minimum. The InN films exhibited a clear sixfold rotational symmetry, without 30° rotational domains and with a full width at half maximum value of the InN 0002 rocking curve being 17.5 arcmin. Comparison between InN films grown on MgAl₂O₄ and those on (Mn,Zn)Fe₂O₄ led us to conclude that suppression of the interfacial reactions between the InN films and the substrate is inherently important to obtain high quality InN on substrates with a spinel structure. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of oxygen content and deposition temperature on the characteristics of thin silver films deposited by magnetron sputtering

Thin silver films were prepared by direct current magnetron sputtering in a single-ended in-line sputter system at various substrate temperatures and in O₂ contents in sputter gas, and their electrical, optical, structural and morphological properties together with the compositional properties were investigated. When deposited at room temperature, the electrical and optical properties of Ag films deteriorated with addition of O₂ to sputter gas. Deposition of Ag films in O₂ added sputter gas promoted the formation of Ag crystallites with (2 0 0) plane parallel to the substrate surface. The electrical resistivity and optical reflection of Ag films deposited above 100 °C were not affected by the sputtering plasma containing oxygen. X-ray photoelectron spectroscopic analysis showed that Ag films deposited above 100 °C in O₂ added sputter gas did not possess surplus oxygen in the film, and that the oxidation states of these films were almost identical to that of Ag films deposited in pure Ar gas.     

Influence of deposition conditions on the structural characteristics of sublimated CdTe thin films

In this paper the results obtained by X-ray diffraction studies on the structural characteristics of CdTe thin films deposited onto glass substrates by close-spaced sublimation technique are presented. Using different experimental arrangements and appropriate settings for growth parameters, the films with different polycrystalline structures were prepared. The geometry and the volume of the deposition chamber influence the size of film crystallites and also their preferential orientation. The role of deposition parameters such as the substrate temperature, the incidence angle, the film thickness, and the heat treatment in determination of the structural properties of the films are also investigated. Received: 26 November 1999 / Accepted: 7 January 2000 / Published online: 5 April 2000     

Thickness influence on surface morphology and ozone sensing properties of nanostructured ZnO transparent thin films grown by PLD

Transparent zinc oxide (ZnO) thin films with a thickness from 10 to 200 nm were prepared by the PLD technique onto silicon and Corning glass substrates at 350 °C, using an Excimer Laser XeCl (308 nm). Surface investigations carried out by atomic force microscopy (AFM) and X-ray diffraction (XRD) revealed a strong influence of thickness on film surface topography. Film roughness (RMS), grain shape and dimensions correlate with film thickness. For the 200 nm thick film, the RMS shows a maximum (13.9 nm) due to the presence of hexagonal shaped nanorods on the surface. XRD measurements proved that the films grown by PLD are c-axis textured. It was demonstrated that the gas sensing characteristics of ZnO films are strongly influenced and may be enhanced significantly by the control of film deposition parameters and surface characteristics, i.e. thickness and RMS, grain shape and dimension.     

Photocatalytic property of TiO2 thin films sputtered-deposited on unheated substrates

TiO₂ films deposited on unheated substrates of alumina silicate glass by rf. (13.56 MHz) magnetron sputtering in the mixture of O₂ and Ar gases have been studied with X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and optical spectroscopy. Structural and optical properties of TiO₂ films deposited at different O₂ concentrations and total pressures have been analyzed. Photocatalytic properties of TiO₂ films were characterized by following the degradation of methylene blue molecules under UV irradiation. It was found that the rate of methylene blue decomposition strongly depends on morphology and crystallinity of the deposited films, namely on the content of the anatase phase and on the size of the anatase grains. The best photocatalytic activity was found on TiO₂ films consisting of pure anatase phase with the size of grains of about 450 Å. With the help of those films a thin film reactor for water purification has been designed and tested.     

Impact of surface step heights of 6H-SiC (0 0 0 1) vicinal substrates in heteroepitaxial growth of 2H-AlN

Impact of step height of silicon carbide (SiC) substrates on heteroepitaxial growth of aluminum nitride (AlN) was investigated. Step-and-terrace structures with various step heights, 6 monolayer (ML), 3ML and 1ML, were formed on 6H-SiC (0 0 0 1) vicinal substrates by high-temperature gas etching. 2H-AlN layers were grown on the substrate by plasma-assisted molecular-beam epitaxy (MBE) and then these layers were characterized by atomic-force microscopy (AFM) and X-ray diffraction (XRD). High-quality AlN can be grown on SiC substrates with 6ML- and 3ML-height step, while AlN grown on SiC substrates with 1ML-height step exhibited inferior crystalline quality. A model for high-quality AlN growth on SiC substrates with 3ML-height step is proposed.     

Structural and mechanical properties of spark plasma sintered n‐ and p‐type bismuth telluride alloys

Spark Plasma Sintering (SPS) is used for the fabrication of wafers of n‐ and p‐type thermoelectric V₂VI₃ materials. The SPS process did not change the overall chemical composition. X‐ray diffraction analysis and the electron backscattered selected area diffraction prove the preferential orientation after the SPS procedure expecting anisotropic thermoelectric prop‐ erties. The mechanical properties of the SPS material are enormously enhanced, so that the fabrication of thin wafers with only 100 µm thickness suitable for the development of Peltier devices with high cooling power density will be possible. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of thickness on structural, optical and electrical properties of nanostructured ZnO thin films by spray pyrolysis

Transparent conducting zinc oxide thin films were prepared by spray pyrolytic decomposition of zinc acetate onto glass substrates with different thickness. The crystallographic structure of the films was studied by X-ray diffraction (XRD). XRD measurement showed that the films were crystallized in the wurtzite phase type. The grain size, lattice constants and strain in films were calculated. The grain size increases with thickness. The studies on the optical properties show that the direct band gap value increases from 3.15 to 3.24 eV when the thickness varies from 600 to 2350 nm. The temperature dependence of the electrical conductivity during the heat treatment was studied. It was observed that heat treatment improve the electrical conductivity of the ZnO thin films. The conductivity was found to increase with film thickness.     

Effect of substrate temperature and annealing temperature on the structural, electrical and microstructural properties of thin Pt films by rf magnetron sputtering

Influence of both substrate temperature, T_s, and annealing temperature, T_a, on the structural, electrical and microstructural properties of sputtered deposited Pt thin films have been investigated. X-ray diffraction results show that as deposited Pt films (T_s = 300, 400 °C) are preferentially oriented along (1 1 1) direction. A little growth both along (2 0 0) and (3 1 1) directions are also noticed in the as deposited Pt films. After annealing in air (T_a = 500-700 °C), films become strongly oriented along (1 1 1) plane. With annealing temperature, average crystallite size, D, of the Pt films increases and micro-strain, e, and lattice constant, a₀, decreases. Residual strain observed in the as deposited Pt films is found to be compressive in nature while that in the annealed films is tensile. This change in the strain from compressive to tensile upon annealing is explained in the light of mismatch between the thermal expansion coefficients of the film material and substrate. Room temperature resistivity of Pt films is dependant on both the T_s and T_a of the films. Observed decrease in the film resistivity with T_a is discussed in terms of annihilation of film defects and grain-boundary. Scanning electron microscopic study reveals that as the annealing temperature increases film densification improves. But at an annealing temperature of ∼600 °C, pinholes appear on the film surface and the size of pinhole increases with further increase in the annealing temperature. From X-ray photoelectron spectroscopic analysis, existence of a thin layer of chemisorbed atomic oxygen is detected on the surfaces of the as deposited Pt films. Upon annealing, coverage of this surface oxygen increases.     

Evolution of dislocations in perylene films with thickness and deposition rate

The growth of perylene films on an amorphous oxide bottom layer is investigated. The perylene films show clear spiral growth and formation of screw dislocations. As a function of deposition rate and film thickness the densities of screw dislocations, grains as well as the roughness and the lateral correlation length are determined from AFM images. The evolution of microstrain as calculated from an XRD peak profile analysis corresponds to the dislocation density. The simultaneous decrease of grain density and dislocation density with film thickness is explained by considering the overgrowth of grains due to loss of dislocations acting as growth spirals. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)

     

Morphological and structural characterizations of CrSi2 nanometric films deposited by laser ablation

The structure and morphology of chromium disilicide (CrSi₂) nanometric films grown on 〈1 0 0〉 silicon substrates both at room temperature (RT) and at 740 K by pulsed laser ablation are reported. A pure CrSi₂ crystal target was ablated with a KrF excimer laser in vacuum (∼3 × 10⁻⁵ Pa). Morphological and structural properties of the deposited films were investigated using Rutherford backscattering spectrometry (RBS), grazing incidence X-ray diffraction (GID), X-ray reflectivity (XRR), scanning (SEM) and transmission electron microscopy (TEM). From RBS analysis, the films’ thickness resulted of ∼40 nm. This value is in agreement with the value obtained from XRR and TEM analysis (∼42 and ∼38 nm, respectively). The films’ composition, as inferred from Rutherford Universal Manipulation Program simulation of experimental spectra, is close to stoichiometric CrSi₂. GID analysis showed that the film deposited at 740 K is composed only by the CrSi₂ phase. The RT deposited sample is amorphous, while GID and TEM analyses evidenced that the film deposited at 740 K is poorly crystallised. The RT deposited film exhibited a metallic behaviour, while that one deposited at 740 K showed a semiconductor behaviour down to 227 K.     

Effect of atmospheric pressure dielectric barrier discharge air plasma on electrode surface

In order to study the influence of plasma on electrode, atmospheric pressure dielectric barrier discharge (DBD) air plasma is employed here to treat copper electrode surface. Plasma is generated between the parallel plate electrodes by means of high voltage produced by a high-frequency power supply with transformer. Electrode surface alterations induced by air plasma are investigated by using field emission scanning electron microscope (FE-SEM), X-ray energy dispersion spectroscopy (EDS) and contact angle measurement. The results show that DBD air plasma removes the organic contaminant on surface and causes electrode surface roughness, oxidization and nitridation. In addition, surface wettability is also improved, as concluded from contact angle measurements.