Fabrication and structural characterization of Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript> nanowires

This article demonstrates the first reported successful synthesis of Mg₂SiO₄ nanowires. We have thermally heated Au-coated Si substrates, using a quartz tube with its inner surface pre-coated with MgO nanostructures. We have characterized the sample morphologies by using scanning electron microscopy and transmission electron microscopy (TEM). X-ray diffraction analysis and high-resolution TEM observation coincidentally revealed that the nanowires were crystalline with an orthorhombic Mg₂SiO₄ structure. We have discussed the possible growth mechanism of Mg₂SiO₄ nanowires. PACS 81.07.-b; 81.05.Zx; 61.10.Nz; 68.37.Hk; 68.37.Lp     

Optical properties of Cd<Subscript>0.6</Subscript>Mn<Subscript>0.4</Subscript>Te/Cd<Subscript>0.5</Subscript>Mg<Subscript>0.5</Subscript>Te quantum-well structures

Emission spectra of three Cd_0.6Mn_0.4Te/Cd_0.5Mg_0.5Te superlattices with Cd_0.6Mn_0.4Te quantum-well (QW) widths of 7, 13, and 26 monolayers, respectively, and the same thickness (46 monolayers) of the Cd_0.5Mg_0.5Te barriers have been studied. The QW width affects the shape and spectral position of the Mn²⁺ intracenter luminescence (IL) band as a result of the crystal field being dependent on the position of the manganese ion with respect to the interface. Measured in identical experimental conditions, the exciton luminescence as compared to the IL is substantially higher in intensity in a QW than in a bulk CdMnTe crystal. Some samples of superlattices and bulk crystals exhibit, in addition to the conventional IL band near 2.0 eV, a weaker band at about 1.45 eV. This band apparently derives from intracenter transitions in the Mn²⁺ ions in the regions where the crystal lattice has the rock-salt rather than the conventional zinc blende structure.     

Exciton and intracenter luminescence in Cd<Subscript>0.6</Subscript>Mn<Subscript>0.4</Subscript>Te/Cd<Subscript>0.5</Subscript>Mg<Subscript>0.5</Subscript>Te quantum-well structures

Exciton luminescence and intracenter luminescence (IL) of Mn²⁺ ions in Cd_0.6Mn_0.4Te/Cd_0.5Mg_0.5Te structures with quantum wells (QWs) 7, 13, and 26 monolayers thick were studied. It was established that in QWs the intensity of exciton luminescence with respect to that of IL is a few orders of magnitude higher than that in bulk crystals. The spectral position of manganese IL profile changes noticeably in going from a bulk crystal to a QW of the same composition. The nonexponential parts of the IL decay curves are determined by excitation migration and the cooperative upconversion process, whose contribution is high under strong excitation and efficient migration. At 77 K, the IL decay constant τ within the exponential region increases with decreasing QW thickness. The decay constant τ in a QW, unlike in a bulk Cd_0.5Mn_0.5Te crystal, decreases substantially under cooling from 77 to 4 K.     

Effects of sintering temperature on the structure and electrochemical performance of Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript> cathode materials

The objective of the present study was to investigate the effects of sintering temperature on the structure and electrochemical performance of Mg₂SiO₄ cathode materials using sol-gel method. X-ray diffraction and Fourier-transform infrared analysis were used to study the structural properties of the materials. The temperatures applied in the sintering process influenced the structure, morphology, as well as particle size distribution of the Mg₂SiO₄. All samples sintered at temperatures of 900, 1000, and 1100 °C yielded pure Mg₂SiO₄ compounds consisting of orthorhombic crystalline phase with a space group of Pbnm. Particle size and lattice parameters of Mg₂SiO₄ samples increased with the increases of sintering temperature due to an increase of the nucleation and crystal growth rates. The cyclic voltammetry analysis showed the presence of redox reaction. This result shows that the Mg₂SiO₄ material has potential to be used as cathode materials in magnesium rechargeable batteries.     

Iron nanoparticles in amorphous SiO<Subscript>2</Subscript>: X-ray emission and absorption spectra

The local structure of the chemical bond of iron ions implanted into SiO₂ glasses (implantation energy, 100 keV; fluence, 1 × 10¹⁶ cm^?2) is investigated using x-ray emission and absorption spectroscopy. The Fe L x-ray emission and absorption spectra are analyzed by comparing them with the corresponding spectra of reference samples. It is established that iron nanoparticles implanted into the SiO₂ vitreous matrix are in an oxidized state. The assumption is made that the most probable mechanism of transformation of iron nanoparticles into an oxidized state during implantation involves the breaking of Si-O-Si bonds with the formation of Si-Si and Fe-O bonds.     

Observation of the quasidiffusive propagation of phonons in Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript>:Ho<Superscript>3+</Superscript> using time-resolved photo-phonon spectroscopy

The energy flux of phonons produced due to the nonradiative laser-induced transitions of Ho³⁺ impurity ions in forsterite from the ⁵F₅ states has been measured using a superconductor bolometer at a temperature of 2 K. The dependence of the flux on the laser wavelength, the time elapsed after the action of a laser pulse, and the phonon propagation path length is analyzed. It is found that the excitation of Ho³⁺ to some states leads to the diffusive propagation of emitted phonons in the spontaneous frequency decay mode (quasidiffusive mode of propagation): the time of arrival of a phonon pulse is almost a linear function of the path length, but it is several times longer than the longest ballistic time of flight (for transverse phonons). The diffusion coefficient and the nonradiative relaxation time are determined from the best fit to the experiment.     

Structure of Mg<Subscript>n</Subscript> and Mg<Stack><Subscript>n</Subscript><Superscript>+</Superscript></Stack> clusters up to n = 30

We present structure calculations of neutral and singly ionized Mg clusters of up to 30 atoms, as well as Na clusters of up to 10 atoms. The calculations have been performed using density functional theory (DFT) within the local (spin-)density approximation, ion cores are described by pseudopotentials. We have utilized a new algorithm for solving the Kohn-Sham equations that is formulated entirely in coordinate space and, thus, permits straightforward control of the spatial resolution. Our numerical method is particularly suitable for modern parallel computer architectures; we have thus been able to combine an unrestricted simulated annealing procedure with electronic structure calculations of high spatial resolution, corresponding to a plane-wave cutoff of 954 eV for Mg. We report the geometric structures of the resulting ground-state configurations and a few low-lying isomers. The energetics and HOMO-LUMO gaps of the ground-state configurations are carefully examined and related to their stability properties. No evidence for a non-metal to metal transition in neutral and positively charged Mg clusters is found in the regime of ion numbers examined here.     

Phase stability and elasticity of Sc<Subscript>2</Subscript>O<Subscript>3</Subscript> at high pressure

An investigation into the high-pressure behavior of Sc₂O₃ was conducted using first-principle calculations based on density functional theory within the generalized gradient approximation. Nine candidate phases were considered and simulated, C-, B-, A-RES, Rh₂O₃(II), Gd₂S₃, U₂S₃, Al₂Er₃, corundum and PPv respectively. Our results demonstrate phase transitions of Sc₂O₃ from C- to B-RES phase at 15 GPa, then to Gd₂S₃ phase at 18 GPa. Elastic constants of Sc₂O₃ present softening from about 270 GPa to 337 GPa, associated with a semiconductor-to-metal crossover. The Gd₂S₃-type Sc₂O₃ is both mechanically and dynamical stable at least up to 302 GPa supported by the mechanically stable criteria and the phonon spectrum.     

Magnetic collapse in yttrium iron garnet Y<Subscript>3</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> at high pressure

The effect of high pressures up to 70 GPa on single-and polycrystalline samples of yttrium iron garnet Y₃⁵⁷Fe₅O₁₂ is studied by Mössbauer absorption spectroscopy (for the ⁵⁷Fe nucleus) in a diamond-anvil cell. It is found that the hyperfine magnetic field H_hf at ⁵⁷Fe nuclei vanishes abruptly at a pressure of 48 ± 2 GPa, which indicates the transition of the crystal from the ferrimagnetic state to nonmagnetic one. The magnetic transition is irreversible. When the pressure decreases, the magnetic state is not recovered and the garnet remains nonmagnetic until zero pressure. The behavior of the quadrupole splitting and isomer shift shows that, simultaneously with the magnetic transition, irreversible electron and possibly spin transitions occur with changes in the local crystalline structure. The mechanisms of the magnetic collapse are discussed.     

The effect of packing density on luminescence of amorphous SiO<Subscript>2</Subscript> nanoparticles

Photoluminescence of amorphous SiO₂ nanoparticles compressed in the form of tablets is studied under exposure to UV radiation. The observed luminescence spectrum is a broad band extending from the excitation wavelength to 700 nm and with a maximum at ~470 nm. The spectrum can be decomposed into two Gaussian components with maxima at ~460 and ~530 nm. As the pressure applied for sample preparation increases, the integrated intensities of these bands change in opposite directions—the intensity of the short-wavelength band increases, while that of the long-wavelength band decreases. It is concluded that these bands are due to different luminescence centers of silicon dioxide located on the surface and in the bulk of SiO₂ nanoparticles.     

Structural and magnetic phase transitions in Pr<Subscript>0.15</Subscript>Sr<Subscript>0.85</Subscript>MnO<Subscript>3</Subscript> at high pressure

The crystal and magnetic structures of Pr_0.15Sr_0.85MnO₃ manganite have been studied by means of powder X-ray and neutron diffraction in the temperature range 10–400 K at high external pressures up to 55 and 4 GPa, respectively. A structural phase transition from cubic to tetragonal phase upon compression was observed, with large positive pressure coefficient of transition temperature dT _ct /dP = 28(2) K/GPa. The C-type antiferromagnetic (AFM) ground state is formed below T _N ≈ 260 K at ambient pressure. While at ambient pressure the structural and magnetic transition temperatures are close, T _ct ~ T _N , upon compression they become decoupled with T _N ≪ T _ct due to much weaker T _N pressure dependence with coefficient dT _N /dP = 3.8(1) K/GPa.     

Spectral and generation properties of a new laser crystal (Cr<Superscript>3+</Superscript>,Li): Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript>

Based on the results of a comparative analysis of luminescence spectroscopy and EPR spectroscopy data, it was found for the first time that the wide-band luminescence of Cr³⁺ ions in a forsterite crystal is due to the Cr³⁺-V_Mg center or, in a crystal additionally doped with lithium, to a Cr³⁺-Li⁺ center. For the first time, tunable laser action was obtained with Cr³⁺-Li⁺ centers responsible for the wide-band luminescence.     

Casimir friction force between a SiO<Subscript>2</Subscript> probe and a graphene-coated SiO<Subscript>2</Subscript> substrate

The possibility of mechanical detection of Casimir friction with the use of a noncontact atomic force microscope is discussed. A SiO₂ probe tip located above a graphene-coated SiO₂ substrate is subjected to the frictional force caused by a fluctuating electromagnetic field produced by a current in graphene. This frictional force will create the bend of a cantilever, which can be measured by a modern noncontact atomic force microscope. Both the quantum and thermal contributions to the Casimir frictional force can be measured using this experimental setup. This result can also be used to mechanically detect Casimir friction in micro- and nanoelectromechanical systems.     

Polarization modes in the Ba<Subscript>2</Subscript>Mg<Subscript>2</Subscript>Fe1<Subscript>2</Subscript>O<Subscript>22</Subscript> multiferroic

The spectra of complex permittivity of a Ba₂Mg₂Fe₁₂O₂₂ single crystal belonging to the family of Y-type hexaferrites have been measured over a wide temperature range (10–300 K) with the aim of determining the dynamic parameters of the phonon and magnetic subsystems in the terahertz and infrared frequency ranges (3–4500 cm⁻¹). A factor-group analysis of the vibrational modes has been performed, and the results obtained have been compared with the experimentally observed resonances. The oscillator parameters of all nineteen phonon modes of E _u symmetry, which are allowed by the symmetry of the Ba₂Mg₂Fe₁₂O₂₂ crystal lattice, have been calculated. It has been found that, at temperatures below 195 and 50 K, the spectral response exhibits new absorption lines due to magnetic excitations.     

Cluster formation in LiNi<Subscript>0.4</Subscript>Fe<Subscript>0.6</Subscript>O<Subscript>2</Subscript>

The structure of an LiNi_0.4Fe_0.6O₂ cubic solid solution is determined using magnetic measurements and electron diffraction. It is found that this solid solution has a microinhomogeneous structure due to the formation of superparamagnetic clusters. The electron diffraction analysis of LiNi_0.4Fe_0.6O₂ samples has revealed diffuse scattering characteristic of the substitutional short-range order in ordered solid solutions with a B1-type structure. It is shown that the short-range order is associated with the LiNiO₂-type rhombohedral superstructure (space group \(R\bar 3m\)), i.e., with the redistribution of lithium and nickel atoms in the (111)_B1 alternating planes. The short-range order is observed in regions with a nickel content higher than the mean nickel content corresponding to the macroscopic composition.     

Photochromism in Cu-and Ag-doped Bi<Subscript>12</Subscript>SiO<Subscript>20</Subscript> crystals

The equilibrium and photoinduced absorption spectra of copper-and silver-doped Bi₁₂SiO₂₀ crystals are studied. It is demonstrated that the impurity absorption is due to Ag²⁺, Ag⁺, Cu³⁺, Cu²⁺, and Cu⁺ ions occupying almost octahedral Bi³ positions. A mechanism of photochromism is suggested, involving changes in the charge states of copper and silver impurity ions according to schemes Cu²⁺-e → Cu³⁺ and Ag⁺-e → Ag²⁺.     

Diode-pumped Yb:Y<Subscript>2</Subscript>SiO<Subscript>5</Subscript>-LiB<Subscript>3</Subscript>O<Subscript>5</Subscript> cyan laser at 501.7 nm

We describe the output performances of the 928 nm ⁴ F _3/2 → ⁴ I _9/2 transition in Nd:CLNGG under diode-laser pumping. An end-pumped Nd:CLNGG crystal yielded 1.3 W of continuous-wave output power for 17.8 W of absorbed pump power. The slope efficiency with respect to the absorbed pump power was 11.2%. Furthermore, with 17.8 W of diode pump power and the frequency-doubling crystal LiB₃O₅ (LBO), a maximum output power of 260 mW in the blue spectral range at 464 nm has been achieved. The blue output power stability over 4 h is better than 3.2%.     

Multilayer metallization of ferrite Mg<Subscript>0.54</Subscript>Zn<Subscript>0.46</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>

The character of interatomic interaction in ferrite Mg_0.54Zn_0.46Fe₂O₄ was studied using the x-ray spectroscopy technique and theoretically. It was found that the electronic structure of samples is rearranged during annealing at high temperatures (1280°C, 0.5–0.8 h). The electronic structure rearrangement was shown to be associated with multilayered ferrite metallization in which alternating layers with metallic and ionic-covalent bonds form.     

Dielectric relaxation in BiLi<Subscript>0.6</Subscript>W<Subscript>0.4</Subscript>O<Subscript>3</Subscript> ceramics

The low-frequency process of dielectric relaxation in the new lead-free compound BiLi_0.6W_0.4O₃ prepared by conventional ceramic technology is studied. The features of dielectric relaxation are discussed in terms of a model of interaction between the domain boundaries and point defects of a crystalline lattice.     

RETRACTED ARTICLE: Refractive-index tailoring and morphological evolutions in Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite thin films

Refractive-index tailoring and morphological evolutions in two different thin film composite systems of gadolinia–silica (Gd₂O₃:SiO₂) and zirconia–silica (ZrO₂:SiO₂) deposited through reactive electron-beam codeposition processes are discussed in this research paper. For Gd₂O₃:SiO₂ the refractive-index tuning has been achieved from 1.45 to 2.18, whereas in the case of ZrO₂:SiO₂ the achieved tunable range is from 1.45 to 2.45 in the ultraviolet region. Under certain compositional mixings with lower silica fractions both the systems demonstrated relative microstructural and morphological densifications. Such evolutions were very successfully derived through phase-modulated ellipsometry and atomic force microscopy. The composition-dependent refractive-index tailoring and microstructural densifications have been investigated by adopting Tauc–Lorentz and single-effective-oscillator models. The morphological correlation functions have also very aptly supported such evolutions in these composite films. These experimental results indicate their favourable properties and applicability down to the extreme ultraviolet wavelength region of the electromagnetic spectrum. PACS 42.79.Wc; 78.66.-w; 78.20.Ci; 61.16.Ch; 42.70.-a;68.55.-a; 68.35.Bs; 81.15.Ef