加速器驱动次临界系统注入器Ⅰ束测系统（英）

加速器驱动次临界系统注入器Ⅰ,包括ECR离子源、低能传输线、射频四极加速单元、中能传输段和超导腔,注入器Ⅰ出口能够获得能量10 MeV的强流质子束流。为了调束和运行的需要,注入器Ⅰ将安装束流位置测量、束流截面测量、束流流强测量、束流发射度和能量测量,以及束流损失测量等束流参数测量装置。介绍了这些束流测量系统设计及其他方面的一些考虑。     

泵浦光束质量对受激拉曼散射的影响

主要讨论泵浦光束质量对低气压拉曼种子源特性的影响。文中给出了一阶斯托克斯光泵浦阈值、输出能量和光束质量的实验数据。用Ｍ＾２因子分析了泵浦光和一阶斯托克斯光的光束质量。根据考虑泵浦聚焦和泵浦光束质量影响的近似拉曼散射理论计算了泵浦阈值的理论曲线，并与实验数据和有关文献进行了比较。     

不同入射角度下强流脉冲电子束能量沉积剖面和束流传输系数模拟计算

 强流脉冲电子束在材料中的能量沉积剖面、能量沉积系数和束流传输系数受其入射角的影响很大，理论计算了0.5~2.0MeV的电子束以不同的入射角在Al材料中的能量沉积剖面和能量沉积系数，并且还计算了0.4~1.4MeV电子束以不同入射角穿透不同厚度C靶的束流传输系数。计算结果表明，随着入射角的增大，靶材表面层单位质量中沉积的能量增大，电子在靶材料中穿透深度减小，能量沉积系数减小，相应的束流传输系数也减小；能量为0.5~2.0MeV的电子束当入射角在60°~70°时在材料表面层单位质量中沉积的能量较大。     

上海光源直线加速器的能量反馈控制

海光源恒流注入的运行模式,需要直线加速器提供持续、稳定和高品质的束流。阐述了八条形电极束流位置探测器(BPM)的工作原理及其对直线加速器至增强器低能运输线的束流进行能散的测量,并以（微波）幅度或相位作为调节参数,采用比例积分(PI)控制算法对束流能散进行反馈控制,实现了束流能量的长期稳定性,保证了直线加速器束流的高效率注入。     

Observation of the anomalous increase of the longitudinal energy spread in a space-charge-dominated electron beam

We report a new experimental study of the growth of longitudinal energy spread in a space-charge-dominated electron beam, with a beam energy of several keV and beam current of approximately 100 mA. At relatively low beam densities, we measure growing energy spreads with distance along the transport channel, which are in remarkably good agreement with the theory of energy relaxation via Coulomb collisions. At higher beam densities, however, anomalous energy spreads exceeding the predictions of the relaxation theory are observed, which, we believe, could be caused by collective longitudinal-transverse instabilities observed in computer simulation studies. The onset of these instabilities occurs after several plasma periods according to calculations.     

超快电子衍射装置的束流能量反馈控制

上海交通大学的超快电子衍射(UED)装置由一台电子直线加速器作为驱动,电子枪为一台光阴极微波电子枪。加速器在运行中电子枪会偶尔打火,腔体失谐,造成束流损失,束流能量产生变化,束流需要很长时间才能恢复到初始状态,影响了用户的使用。为此,对低电平控制器(LLRF)的幅度相位控制环路进行了改进,增加了能量反馈,代替了幅度反馈,通过对束流的中心位置进行实时的反馈以控制低电平控制器输出信号的幅度,保证了电子束流的能量稳定和电子枪加速场强的稳定。长时间的稳定性测试表明,电子枪在打火产生时,束流能量可以很快恢复,能量抖动由4.2933×10^-4(RMS)提高到2.8557×10^-4(RMS),实现了束流能量的长期稳定。     

Efficiency enhancement in free-electron lasers by means of concurrent rf acceleration

Efficiency enhancement in free-electron lasers (FELs) using rf beam acceleration in the wiggler is described. Since the beam tube is a waveguide, there are low and high frequency resonances. Injection of low frequency power can act as an inverse-FEL accelerator concurrently with high frequency power extraction. Simulation of a FEL using this technique shows that substantial efficiency enhancements are possible without significant increases in the beam energy spread, which facilitates the use of energy recovery schemes. The technique is applicable to amplifier and oscillator configurations.     

高能激光光束质量β因子的影响因素分析

采用二维线性调频z变换算法,分析了影响高能激光系统光束质量β因子测量准确性的因素。本文详细分析了采样点数(即衍射极限内的采样点数)和衍射光斑图像的能量损失率对光束质量β因子的影响。在衍射极限角直径2(λ/D)范围内不同采样点数的模拟结果表明:采样点数越高,光斑衍射图像的分辨率越高,进而光束质量β因子计算越准确。在一倍衍射极限角2.44(λ/D)范围内应最低不少于10个采样点,即可将β因子的测量误差控制在3%。同时,不同像差对光斑图像能量损失率的敏感程度不同,相同能量损失率下,高阶像差的β因子测量误差要高于低阶像差。特别是球差类的像差对能量损失最为敏感,约5%的能量损失就可带来15%~30%的β因子计算误差。     

Generation of high energy and good beam quality pulses with a master oscillator power amplifier

A high efficiency and high peak power laser system with short-pulse and good beam quality has been demonstrated by using a master oscillator power amplifier with two-pass amplification configuration. The master oscillator, end-pumped with a fiber-coupled laser diode array, provides low power but excellent beam quality pulses, and the amplifier boosts the pulse energy by orders without significant beam quality degradation. Short pulses of 8.5 ns with energy up to 130 mJ and approximately diffraction limited beam quality have been demonstrated.     

用于能量标定的束流损失测量系统

为精确地测量合肥电子储存环电子束的能量,建立了一套束流损失的测量装置,选择了一款对低能光子探测效率高的塑料闪烁体探测器,根据测量到的束流损失信号研制了一套数字化的信号处理电路,并进行了实际测量。测量结果表明该束流损失测量系统能够精确、灵敏地反映出束流损失的变化,可以用于自旋共振退极化法标定电子束能量的实验;并介绍了自旋共振退极化法的测量原理及依据的理论基础。     

Energy spread in plasma-based acceleration

Electron acceleration in a one-dimensional plasma wave has been simulated, with emphasis on minimizing the energy spread of an accelerated electron bunch, while keeping the mean energy gain at a reasonable level. Bunch length, beam loading, and the injection phase are tuned to reach this goal. The simulation results show that, in a wide range of initial bunch lengths and beam loading parameters, an optimum acceleration distance exists, which combines low energy spread and high energy gain. The energy spread at the optimum is found to be weakly dependent on bunch length and beam loading, while it is highly sensitive to deviations in the injection phase     

Monte Carlo方法研究低能电子束曝光沉积能分布规律

建立一个描述低能电子在多元多层介质中散射的物理模型,运用MonteCarlo方法模拟低能电子在靶体胶衬底中的复杂散射过程,在此基础上通过大量计算研究入射束能、胶层厚度、衬底材料等不同曝光条件对抗蚀剂沉积能密度分布的影响,获得沉积能分布规律:适量的低束能、薄胶层、低原子序数衬底可以使前散射电子对胶中沉积能密度分布的贡献增大、背散射电子的贡献减小,从而提高曝光分辨率. 关键词： 电子束曝光 MonteCarlo方法 低能电子散射 能量沉积     

合肥光源慢加速过程中高频系统的调节

 合肥光源是一台专用同步辐射光源，它在低能注入积累束流，然后同步地把束流加速到高能并在储存环中稳定运行。在加速过程中，粒子的同步辐射能量损失迅速增加，束流负载效应发生变化，需要相应地调节高频系统参数保持束流稳定。讨论了合肥光源加速过程中高频系统可能的两种高频系统调节方式以及高能情况下高频系统的最佳运行状态。     

HIRFL中的束流纵向运动

 对兰州重离子加速器的两台等时性回旋加速器中的束流纵向运动作了简单分析,主要介绍两条束运线上的几台聚束器的物理设计。超低能束运线SFC轴向注入线上的两台聚束器采用了线性聚束器,并提出了用半频聚束来提高两台回旋加速器的纵向匹配效率的新方法。低能束运线(BL1)上的聚束器采用多工作模式以解决加速粒子和能量范围宽的问题。     

KLY—1低能宽束离子源的研制

本文简介了KLY-1低能宽束离子源的结构,给出了物理设计的主要公式和调试实验的结果。对于氩离子束,在离子能量为4keV,距引出电极24cm处的5cm直径的靶上,测得最大氩离子流为45mA,束流不均匀性优于±25％。     

氢化作用对低能电子束辐照下GaN发光演变的影响

结合氢在GaN中的扩散特性,运用阴极荧光（CL）谱,对氢化前后低能电子束辐照下GaN带边发光强度的演变进行了研究.实验发现,氢化前GaN在低能电子束辐照下带边发光强度呈现衰减的趋势,而氢化后带边发射强度先上升后衰减,而且氢化后的衰减比氢化前弱.1 h辐照过程中,氢化后GaN带边发光强度的变化比氢化前要小很多.另外,实验中发现经过氢化处理的GaN在辐照后20 h内没有观察到带边发射强度的恢复.研究表明氢原子在GaN中可以钝化缺陷来增强发光,但这种钝化缺陷的作用必须通过克服高的扩散势垒来实现,而低能电子束可以 关键词： 阴极荧光 低能电子束 氢化 演变     

高能激光束自动对准和稳定系统的结构设计

介绍了一种用于两个光学平台之间光轴自动对准和稳定光束的设计方案。以可绕ｘ,ｙ,ｚ三个方向转动的导光管为单元,组成导光臂连接两个光学平台,消除两个平台之间相对运动产生的光轴对接偏差。用压电陶瓷驱动的倾斜镜作光束稳定元件,消除光束自身的漂移和平台间高频振动产生的光轴偏差。     

低阻抗二极管产生的强流电子束能谱分布的数值模拟

 给出了低阻抗二极管产生的电子束能谱分布及外加磁场对二极管阻抗影响的数值模拟研究结果。结果表明，即使在外加电压恒定的条件下，二极管产生的电子束也具有一定的能谱分布，这说明用二极管电压、电流波形计算脉冲电子束能谱分布是不正确的。另外,外加磁场对低阻抗二极管的阻抗特性具有较大影响，其阻抗随外加磁场的增大而减小。分析认为这是由于外加磁场强度的变化改变了二极管中束电子的运动轨迹。当没有外加磁场或外加磁场较小时，低阻抗二极管产生的电子束发生自箍缩，此时二极管电流是自箍缩饱和顺位流；当外加磁场足够强时，电子束的自箍缩被抑制，二极管电流是没有箍缩时的空间电荷限制电流。束电流小于自箍缩临界电流的二极管其阻抗将不随外加磁场的变化而变化。     

BEPCII Injector Linac Upgrade and Beam Instabilities

The upgrade project of the Beijing Electron Positron Collider （BEPCII） and its injector linac is working well. The linac upgrade aims at a higher injection rate of 5OmA/min into the storage ring, which requires an injected beam with low emittance, low energy spread and high beam orbit and energy stabilities. This goal is finally reached recently by upgrading the linac components and by dealing with rich and practical beam physics, which are described in this study.     

Progress of the Injector Linac Upgrade for the BEPCⅡ Project

BEPCⅡ—an upgrade project of Beijing Electron Positron Collider (BEPC) is a factory type of e+e- collider. It requires its injector linac to have a higher beam energy (1.89 GeV) for on-energy injection and a higher beam current (40 mA e+ beam) for a higher injection rate ( 50 mA/min). The low beam emittance (1.6π mm·mrad for e+ beam, and 0.2πmm·mrad for 300 mA e- beam) and the low beam energy spread (±0.5%) are also required to meet the storage ring acceptance. Thus the original BEPC injector linac must be upgraded to have a new electron gun with its complete tuning system, a new positron source with a flux concentrator, a new RF power system with its phasing loops and a new beam tuning system with orbit correction and optics tuning devices. These new components have been designed, fabricated, tested and will be installed in their final positions in this spring and summer, which are described in this paper.