Adsorption of chlorhexidine onto cellulosic fibers

Comparative investigations of adsorption properties of chlorhexidine (CHX) on two cellulose fibers, bleached cotton and viscose, were studied in order to obtain dry gauzes covered with known amount of this antiseptic. Adsorption isotherm results carried out at 293 and 323 K can be described by Langmuir isotherm model, nevertheless, at high concentration correlation is better to Freundlich isotherm. Electrokinetic potential evolution with CHX concentration, shows that initial negative zeta potential of cotton and viscose diminish its absolute value as the concentration of the treatment increases; both fibers present an isoelectric point at high concentration of CHX that is 0.3 mM for viscose and 0.8 mM for cotton. Electrostatic interactions between cationic groups of CHX and carboxylic acid groups of the fibers could explain adsorption at low concentration, but when it is higher than these values, possible hydrogen bonding between the amine groups of CHX and hydroxyl groups of cellulose could explain increasing adsorption when it is hindered by electrostatic repulsion as it is predicted by Freundlich model, that describes heterogeneous surface and multilayer adsorption. Adsorption kinetics isotherms reveal that the process is quick with t _1/2 values of 5.4 min for cotton and 2.8 min for viscose. Differences in adsorption behaviour between the two fibers could be attributed to structural differences as we have observed from estimation of CI index based on FTIR spectra. Values obtained 1.6 for viscose and 2.2 for cotton could explain that the amount of CHX adsorbed on viscose is higher than it is on cotton. Finally desorption experiments performed with 0.01 M of NaCl solution at room temperature and pH 6 reveals the possibility of therapeutical application of these fibers although further investigations must be done to optimize the process.     

Adsorption and inactivation behavior of horseradish peroxidase on cellulosic fiber surfaces

The physical immobilization behavior of horseradish peroxidase (HRP) on cellulosic fiber surfaces was characterized using adsorption and inactivation isotherms measured by the depletion method followed by fitting of Langmuir’s and Freundlich’s models to the experimental data. The adsorption and inactivation behavior of simpler and relatively non-porous high and low crystalline cellulosic substrates (microcrystalline cellulose and regenerated cellulose) as well as more complex and porous cellulosic pulp fibers (bleached kraft softwood fibers) were investigated. The effect of the sorbent surface energy on HRP adsorption was demonstrated by increasing the hydrophobicity of the cellulosic fibers using an internal sizing agent. The influence of the fiber surface charge density on HRP adsorption was studied via modification of the cellulosic fibers using TEMPO (2,2,6,6-tetramethyl-1-piperidiniloxy radical)-mediated oxidation methods. Results showed that hydrophobic interactions had a much larger effect on HRP adsorption than electrostatic interactions. More hydrophobic fiber surfaces (lower polar surface energy) result in larger enzyme-fiber binding affinity constants and higher binding heterogeneity. It was also found that oxidation of the cellulosic fiber substrate reduces enzyme adsorption affinity but significantly increases the loading capacity per unit weight of the surface.     

Adsorption of cationic surfactants and subsequent adsolubilization of organic compounds onto cellulose fibers

Cationic surfactants with different hydrophobic chain length were adsorbed onto cellulose fibers in an aqueous medium. The adsorption isotherms exhibited three characteristic regions which were interpreted in terms of the mode of aggregation of the surfactant molecules at the solid–liquid interface. The hydrophobic layers were used as a reservoir to trap various slightly water soluble organic molecules. A quantitative study of these phenomena suggested typical partition behavior of the organic solutes between the aqueous phase and the surfactant layer. The surfactant chain length (from C12 to C18) was shown to play an important role in terms of the capacity to retain the organic solute and the capacity increased with the number of carbon atoms.     

Adsorption of organic compounds onto polyelectrolyte immobilized-surfactant aggregates on cellulosic fibers

The adsorption of anionic surfactants with different hydrophobic chain lengths onto cellulose fibers pretreated with a cationic polyelectrolyte has been investigated. Five steps are involved in the adsorption process, which was ascribed to the formation of monolayer and bilayer surfactant aggregates. Electrostatic interaction between the residual surface charges followed by hydrophobic interaction among the alkyl chains are considered the main factors in the adsorption process. The adsorption of the anionic surfactant was found to greatly enhance the retention of organic compounds onto the polyelectrolyte-treated cellulose. The coadsorption phenomenon, which was dependent on the saturation level of the adsorbed surfactant, has been explained in terms of the accumulation of the organic solute on the hydrophobic core generated by the adsorbed layer.     

Physicochemical properties of chemically and enzymatically modified cellulosic surfaces

Surface characteristics of modified cotton fibers have been studied using electrokinetic analysis (EKA), inverse gas chromatography (IGC) and dynamic contact angle (DCA) determinations. Modifications of cotton surfaces included mercerization, water-proofing, cross-linking, dyeing with a bifunctional reactive dye and cellulase biopolishing. Comparisons are made to linen as an example of a natural cellulosic fiber other than cotton and to rayon as a representative of a regenerated cellulosic fiber. Generally all cellulosic surfaces were bipolar with a slightly higher acidic contribution in the case of the cotton samples. EKA indicated ion dissociation as the predominant mechanism for surface charge in aqueous medium for all cellulosic samples, with the exception of greige cotton and the cotton sample with the hydrophobic finish. Results from EKA and IGC showed good correlation, while DCA yielded unreasonably high basic contributions most likely due to fiber swelling.     

Grafting of acrylamide onto cellulosic fibers via dielectric-barrier discharge

Fully bleached kraft pulp (BKP) and thermomechanical pulp (TMP) fibers were grafted with acrylamide via dielectric-barrier discharge treatment at various treatment dosages. The results indicate that increased dielectric-barrier discharge treatment leads to the increased polymerization and incorporation of acrylamide onto fiber surfaces. Greater incorporation of poly(acrylamide) occurs on the BKP fibers than the TMP at the same treatment conditions. Time-of-flight secondary ion mass spectrometry (ToF-SIMS) and scanning electron microscopy (SEM) indicate that dielectric-barrier discharge initiated modifications to fiber surface topo-chemistry occur across the fiber such that the sheet is randomly peppered with modified areas; however, it occurs in patches on individual fibers as opposed to occurring as an evenly distributed thin film. SEM and elemental analysis also showed that the incorporation of acrylamide onto the fiber surface increases with increased treatment dosages.     

Sorption studies on regenerated cellulosic fibers in salt–alkali mixtures

The degrees of salt sorption were determined in lyocell and viscose fibers immersed in aqueous solutions of salt–alkali mixtures with the aim of using salt sorption as an indirect measure of changes to fiber accessibility in presence of alkali. The salt–alkali mixtures used were combinations of NaOH with NaCl or NaBr, and of KOH with KCl or KBr. In general, salt sorption in fibers increased with increase in alkali concentration up to 2 mol/l, and did not change significantly thereafter. The accessibility of Br⁻ salts was greater than the Cl⁻ salts, but that of the Na⁺ salts was greater than the K⁺ salts. These trends in salt sorption indicate that salt accessibility in fibers is not influenced by the size of hydrated salt ions, but by the forces of electrostatic attraction and repulsion between the charged fiber surface and salt cations and anions.     

Facile extraction,processing and characterization of biorenewable sisal fibers for multifunctional applications

Synthetic fibers based materials have replaced most of the traditional metallic/ceramic materials for a number of applications owing to their enormous properties such as light weight, specific strength and modulus to name a few. Unfortunately, the traditional synthetic fibers are not desired from the health and environmental point of view. So, in this work, we have carried out the isolation, processing and characterization of cellulosic sisal fibers. These fibers were extracted for the first time by a simple and new unique mechanical extraction technique without affecting the quality of fibers. Subsequently these cellulosic sisal fibers were thoroughly characterized for their physicochemical, microstructure and mechanical properties. These fibers were then converted into fine textured sisal textile yarn made out of 3–6 sisal fibers in continuous operation and used for the preparation of new green materials. Different properties of fine textured sisal textile and the impact of sisal fine textile on the physical, microstructural, thermal and mechanical characteristics of the green materials were studied and discussed in detail.     

Adsorption and adsolubilization of surfactants on titanium dioxides with functional groups

Adsorption of ionic surfactants on titanium dioxide with dodecyl chain groups or quaternary ammonium groups (XNm, where m is the carbon number of the alkyl chain, 4–16) was investigated. The adsorbed amount of cationic surfactants (dodecyltrimethylammonium bromide, DTAB; 1,2-bis(dodecyldimethylammonio)ethane dibromide, 2RenQ) on titanium dioxide with dodecyl chain groups increased with increasing concentration of the dodecyl chain due to hydrophobic interaction, where the adsorbed amounts of DTAB at saturation was considerably greater than those of 2RenQ. Adsorption of an anionic surfactant (sodium dodecyl sulfate, SDS) on XNm occurred mainly due to both electrostatic attraction force and hydrophobic interaction, depending on the alkyl chain length on XNm. On the other hand, adsorption of cationic surfactants, DTAC and 2RenQCl (their counter ions are chloride ions), on XNm was quite smaller compared with that of SDS due to electrostatic repulsion force. Adsolubilization of 2-naphthol in the surfactant-adsorbed layer on the titanium dioxides with the functional groups was also studied. The adsolubilized amounts of 2-naphthol on titanium dioxide with dodecyl chain groups were enhanced by adsorption of DTAB, but no distinct increase in the adsolubilization was observed by adsorption of 2RenQ. In the case of XNm, the amount of 2-naphthol adsorbed in the absence of surfactants increased with increasing alkyl chain length on XNm. Further, an appreciable increase in the adsolubilization of 2-naphthol on XNm with adsorption of 2RenQCl was observed. It was found from the admicellar partitioning coefficients that the adsolubilization of 2-naphthol preferably occurs on XNm by adsorption of SDS or 2RenQCl compared with that by DTAC. These differences in the adsolubilization were discussed by microproperties of the surfactant-adsorbed layers estimated using a spin probe.     

Physico-chemical properties of new cellulosic fibers from the bark of Acacia planifrons

Identification of new natural fibers is growing due to their superior properties and the impetus for researchers to develop high-performance composites. This investigation was aimed at understanding the physico-chemical properties of Acacia planifrons fibers (APFs). The crystalline structure of APFs was analyzed by X-ray diffraction, and the crystallinity index (65.38%) was calculated. The chemical functional group of APFs was confirmed by Fourier transform-infrared spectroscopy, the thermal stability measured by thermogravimetric analysis, and surface characterization established by atomic force microscopy. Taken together, all the properties of APFs can play a vital role in establishing APFs as new reinforcement in polymer composites.     

Adsorption of a cationic surfactant onto cellulosic fibers I. Surface charge effects

The adsorption of four cationic surfactants with different alkyl chain lengths on cellulose substrates was investigated. Cellulose fibers were used as model substrates, and primary alcohol groups of cellulose glycosyl units were oxidized into carboxylic groups to obtain substrates with different surface charges. The amount of surfactant adsorbed on the fiber surface, the fiber zeta-potential, and the amount of surfactant counterions (Cl(-)) released into solution were measured as a function of the surfactant bulk concentration, its molecular structure, the substrate surface charge, and the ionic strength. The contribution of each of these parameters to the shape of the adsorption isotherms was used to verify if surfactant adsorption and self-assembly models usually used to describe the behavior of surfactant/oxide systems can be applied, and with which limitations, to describe cationic surfactant adsorption onto oppositely charged cellulose substrates.     

Preparation and adsorption of novel cellulosic fibers modified by β‐cyclodextrin

Novel cellulosic fibers modified by β‐cyclodextrin (CFEC) were prepared for adsorption for heavy metal ions like copper (II) and organic dye like neutral red from their aqueous solutions. The modified cellulosic fibers gave higher copper ion adsorption, and showed copper ion uptake values of 6.24 mg/g at 293°C, as against no adsorption for unmodified cellulosic fibers. Adsorption isotherm model indicated the adsorption of the novel modified fibers for heavy metal ions best fitted for Langmiur model. The adsorption was an exothermic reaction, and the reaction caloric was 6.295 kJ/mol. Copper ions could form a 7:4 complex with β‐cyclodextrin (β‐CD). The novel modified cellulosic fibers could also form inclusion complexes with neutral red via β‐CD molecules. In addition, it was found that the novel modified cellulosic fibers had nearly the same mechanical and thermal properties as the unmodified cellulosic fibers because the modification did not destroy the main chain of cellulose molecules. Copyright © 2008 John Wiley & Sons, Ltd.     

Sorption of 2,4-dichlorophenol on modified hydrotalcites

The adsorption of anionic surfactants (sodium dodecyl sulfate (SDS) and sodium bis[2-ethylhexil]sulfosuccinate (AOT)) on hydrotalcite (HT) and the adsorption of 2,4-dichlorophenol (DCP) on HT and its modified forms from aqueous solutions was studied. The modification was carried out by calcinations (heat treatment) and hydrophobization using different anionic surfactants. The anionic surfactant isotherms were of the H-type. It was assumed that first the ion exchange mechanism takes place until approximately the anion exchange capacity of HT is reached and hereafter, the hydrophobic mechanism occurs forming surfactant bilayers. While the DCP adsorption was very poor on HT, significant uptake of DCP took place on calcined HT which was attributed to the simultaneously occurring rehydration and adsorption during the reconstruction of the layered structure. On anionic surfactant-HT complexes (“organo-hydrotalcites”) DCP was considerably adsolubilized in the anionic surfactant layers intercalated in HT. The AOT–HT complex appeared the more effective adsorbents for DCP.     

Extraction and characterization of new cellulosic fibers from Indian mallow stem: An exploratory investigation

Natural fibers are one of the good alternative sources for replacing synthetic fiber and reinforcing polymer matrices because of their eco-friendly nature. This investigation deals with the extraction and characterization of new natural fiber from Indian mallow plant stem. The physico-chemical, thermal, and mechanical properties of Indian mallow fibers (IMFs) were reported and compared with other natural fibers for the first time. Cellulose (78.22%), wax (0.47%), density (1.33 g/cm³), and tensile strength (979.83 MPa) were recognized in IMFs. Fourier transform-infrared spectroscopy, X-ray diffraction, and thermo-gravimetric analysis confirmed that IMFs are rich in cellulose content and thermally stable with a crystallinity index of 72%.     

Extraction and characterization of natural cellulosic fiber from Passiflora foetida stem

This article presents a comprehensive characterization study of natural cellulosic fiber extracted from Passiflora foetida vine stem. The chemical composition of the obtained P. foetida fibers (PFFs) comprised high cellulose (77.9 wt%) and low lignin (10.47 wt%) content and had distinctly higher crystallinity (67.36%) of cellulose, which was determined by an X-ray diffractometer. The PFFs exhibited good tensile strength of 248?942 MPa associated with elongation (1.38?4.67%) during tensile testing. Thermogravimetric analysis revealed that the PFFs are thermally stable up to 320°C with kinetic activation energy of 85.46 kJ mol^?1; hence they ensure their suitability as a reinforcing phase in composites for potential applications.     

Radiation and chemical pretreatment of cellulosic waste

RADIATION AND CHEMICAL PRETREATMENT OF CELLULOSIC WASTE. Combination pretreatment of cellulosic wastes such as corn stalk, cassava bark and peanut husk were studied using chemical and irradiation of electron beam. The effect of 2 % NaOH and irradiation at the doses of 100, 300 and 500 kGy on the cellulosic wastes were evaluated by measurement of the glucose yield in enzymatic hydrolysis. Irradiation was carried out with an electron beam machine EPS-300 (Energy 300 kev, current 50 mA). The result shows that the glucose yield were higher by increasing of dose irradiation and treated with 2 % of NaOH especially in corn stalk. The glucose yield of corn stalk were 20 % in untreated samples and increases to 43 % after treated with electron beam irradiation at the dose of 500 kGy and 2 % NaOH. Cassava bark and peanut husk show the glucose yield are only 3.5, and 2.5% respectively. The effect of E-beam current in enzymatic hydrolysis of corn stalk, and preliminary studied E-beam radiation pretreatment of cassava bark are also reported.     

Effects of degassing and ionic strength on AFM force measurements in octadecyltrimethylammonium chloride solutions

Sakamoto et al. (Langmuir 2002, 18, 5713) conducted AFM force measurements between silica sphere and fused-silica plate in aqueous octadecyltrimethylammonium chloride (C18TACl) solutions and concluded that long-range attractive force is not observed in carefully degassed solutions. In the present work, AFM force measurements were conducted by following the procedures described by Sakamoto et al. The results showed the presence of an attractive force that was much stronger than the van der Waals force both in air-saturated and degassed solutions. The force was most attractive at 5 x 10(-6) M C18TACl, where contact angle was maximum. At this concentration, which is close to the charge compensation point (ccp) of the glass sphere, the long-range decay lengths (D) were 34 and 38 nm in air-saturated and degassed solutions, respectively. At 10(-5) M, the decay length decreased from 30 to 4 nm upon degassing. This decrease in decay length can be explained by a pH increase (from 5.7 to 6.6), which in turn causes additional surfactant molecules to adsorb on the surface with inverse orientation. The attractive force was screened by an added electrolyte (NaCl), indicating that the attractive force may be of electrostatic origin. Therefore, the very long decay lengths observed in the absence of electrolyte may be ascribed to the fact that the ccp occurs at a very low surfactant concentration.     

Effect of wet spinning parameters on the properties of novel cellulosic fibres

Novel cellulose fibres (Biocelsol) were spun by traditional wet spinning technique from the alkaline solution prepared by dissolving enzyme treated pulp directly into aqueous sodium zincate (ZnO/NaOH). The spinning dope contained 6 wt.% of cellulose, 7.8 wt.% of sodium hydroxide (NaOH) and 0.84 wt.% of zinc oxide (ZnO). The fibres were spun into 5% and 15% sulphuric acid (H₂SO₄) baths containing 10% sodium sulphate (Na₂SO₄). The highest fibre tenacity obtained was 1.8 cNdtex⁻¹ with elongation of 15% and titre of 1.4 dtex. Average molecular weights and shape of molecular weight distribution curves of the celluloses from the novel wet spun cellulosic fibre and from the commercial viscose fibre were close to each other.     

Automated extraction of direct,reactive, and vat dyes from cellulosic fibers for forensic analysis by capillary electrophoresis

Systematic designed experiments were employed to find the optimum conditions for extraction of direct, reactive, and vat dyes from cotton fibers prior to forensic characterization. Automated microextractions were coupled with measurements of extraction efficiencies on a microplate reader UV–visible spectrophotometer to enable rapid screening of extraction efficiency as a function of solvent composition. Solvent extraction conditions were also developed to be compatible with subsequent forensic characterization of extracted dyes by capillary electrophoresis with UV–visible diode array detection. The capillary electrophoresis electrolyte successfully used in this work consists of 5 mM ammonium acetate in 40:60 acetonitrile–water at pH 9.3, with the addition of sodium dithionite reducing agent to facilitate analysis of vat dyes. The ultimate goal of these research efforts is enhanced discrimination of trace fiber evidence by analysis of extracted dyes. Figure Fitted absorbance response surface for extraction of a direct dye, C. I. yellow 58, using a ternary solvent system.