新型碳纤维负载直接乙醇燃料电池Pt-SnO_2阳极催化剂的性能研究

采用静电纺丝技术制备了碳纤维基纳米Pt-SnO2阳极催化剂(Pt/Sn原子比为3)。通过X射线衍射(XRD)、红外光谱(FT-IR)、扫描电子显微镜(SEM)等技术对该催化剂进行了表征,并采用循环伏安法对其在乙醇燃料电池中的阳极催化活性进行了评价。结果表明,纳米Pt-SnO2催化剂均匀地分散在碳纤维骨架上;随着烧结温度的升高,碳纤维载体的致密度越高、导电性能越好。电催化性能测试表明,烧结温度为800℃时催化剂的峰电流密度最大,达到0.11 A/cm2,抗中毒能力也最强。单电池的发电性能表明,在一定的乙醇浓度下,1.0 mL/min进样流速具有最优的发电效率。     

碳纤维基PtSn催化剂直接乙醇燃料电池制备及性能研究

采用自制的碳纤维基PtSn催化剂薄膜作为阳极催化剂,商用Pt/C作为阴极催化剂,Nafion 115膜作为质子交换膜,通过热压制成膜电极,组装平板型直接乙醇燃料单电池,搭建测试系统并进行性能的测试,研究了温度、乙醇浓度、溶液流量、进气流量等参数对DEFC的影响。结果表明,当乙醇溶液浓度为1.0 mol/L、溶液进样流量为1.0 mL/min、溶液温度为80 ℃、氧气进样流量为100 mL/min时结果较优,单电池的最高功率密度达18.2 mW/cm²。     

Synthesis and characterization of niobium-promoted cobalt/iron catalysts supported on carbon nanotubes for the hydrogenation of carbon monoxide

Bimetallic Co /Fe catalysts supported on carbon nanotubes( CNTs) were prepared,and niobium( Nb) was added as promoter to the 70 Co ∶30Fe /CNT catalyst. The physicochemical properties of the catalysts were characterized,and the catalytic performances were analyzed at the same operation conditions( H_2 ∶CO( volume ratio) = 2 ∶1,p = 1 MPa,and t = 260 ℃) in a tubular fixed-bed microreactor system. The addition of Nb to the bimetallic catalyst decreases the average size of the oxide nanoparticles and improves the reducibility of the bimetallic catalyst. Evaluation of the catalyst performance in a Fischer-Tropsch reaction shows that the catalyst results in high selectivity to methane,and the selectivity to C_(5+) increased slightly in the bimetallic catalyst unlike that in the monometallic catalysts. The addition of 1% Nb to the bimetallic catalyst increases CO conversion and selectivity to C_(5+). Meanwhile,a decrease in methane selectivity is observed.     

Synthesis and characterization of nickel catalysts supported on different carbon materials

Nickel catalysts supported on various carbon materials such as multiwall carbon nanotubes, shortened length carbon nanotubes, graphite and amorphous carbon were synthesized, characterized and tested in cyclohexene hydrogenation reaction. We have found that carbon nanotube supports are superior to graphite and amorphous carbon both in terms of catalytic activity and stability.     

多元醇法合成的Pt2.6Sn1Ru0.4/C用作直接乙醇燃料电池高性能阳极催化剂

采用多元醇法制备了不同原子比例和载量的PtSnRu/C催化剂,利用透射电镜和X射线光电子能谱表征了所制备催化剂的物化性能,采用直接乙醇燃料电池（DEFC）单池性能测试了其电化学性能,并利用电化学原位光谱、气相色谱和中和滴定分析了乙醇电氧化过程和产物. DEFC单电池测试表明Pt_2.6Sn₁Ru_0.4/C催化剂具有较高的电池性能,其中,以60 wt% Pt_2.6Sn₁Ru_0.4/C催化剂为阳极的DEFC性能最高,90 ℃下最高功率密度为121 mW/cm². 电化学原位红外光谱和阳极产物分析表明乙酸、乙醛、乙酸乙酯和CO₂是乙醇电化学氧化产物,Pt_2.6Sn₁Ru_0.4/C催化剂上乙醇的氧化效率较高. 阳极乙醇氧化活化能和催化剂表面组成分析结果表明,表面组成的相互作用使Pt_2.6Sn₁Ru_0.4/C催化剂具有较低的乙醇氧化活化能和较高的乙醇氧化活性.     

Manganese(III) porphyrin anchored onto multiwall carbon nanotubes: An efficient and reusable catalyst for the heterogeneous reduction of aldehydes and ketones

Reduction of a variety of carbonyl compounds with NaBH₄, using Mn-porphyrin, meso-tetrakis(4-hydroxyphenyl)porphyrinatomanganese(III), supported onto functionalized multiwall carbon nanotubes has been investigated. The heterogeneous catalyst was characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV–vis spectroscopy. The amount of catalyst loading on the nanotubes was determined by atomic absorption spectroscopy. Thermogravimetric analysis (TGA) demonstrated that the nanocatalyst was thermally stable to almost 300 °C, exhibiting high thermostability of the catalyst over a broad range of temperatures. This heterogeneous catalyst proved to be an efficient catalyst in the aerobic reduction of various aldehydes and ketones with NaBH₄. In the presence of the nanocatalyst, NaBH₄ can readily reduce a variety of aldehydes in good to excellent yields (50–100%) and ketones in excellent yields (100%) to their corresponding alcohols. The separation of the catalyst is very simple and economic. Also, FTIR spectra after four successive cycles showed that the catalyst was strongly anchored to the nanotubes.     

ZIF-8基复合材料高效、稳定电催化还原CO2

电催化CO₂还原反应(eCO₂RR)受到催化剂本征活性以及传质的限制,导致材料的催化活性低、反应起始电位高等问题。我们以类沸石锌盐咪唑骨架(ZIF-8)材料为研究对象,探究了不同粒径ZIF-8材料的eCO₂RR性能。优选粒径为50 nm的ZIF-8材料,进一步引入碳纳米管(CNT)作为其导电基底材料,通过原位生长,构建了复合材料ZIF-8-50@CNT的多级孔结构和疏水界面。eCO₂RR实验结果表明,CNT的引入提高了催化剂的导电性,优化后的复合材料有效地降低了反应的起始电位。在-1.1 V(相对可逆氢电极(RHE))电位下,CO部分电流密度为15.6 mA·cm^-2,ZIF-8-50@CNT催化剂的比表面活性提升了3.5倍(相比ZIF-8-50),塔菲尔斜率降低到136 mV·dec^-1。并且产物CO的选择性和稳定性得到了提高,在宽电势窗口-0.9～-1.2 V(vs RHE)内,CO的法拉第效率(FE)保持在80%以上。在10 h稳定性测试中,催化剂活...     

ZIF-8基复合材料高效、稳定电催化还原CO2

电催化CO₂还原反应(eCO₂RR)受到催化剂本征活性以及传质的限制,导致材料的催化活性低、反应起始电位高等问题。我们以类沸石锌盐咪唑骨架(ZIF-8)材料为研究对象,探究了不同粒径ZIF-8材料的eCO₂RR性能。优选粒径为50 nm的ZIF-8材料,进一步引入碳纳米管(CNT)作为其导电基底材料,通过原位生长,构建了复合材料ZIF-8-50@CNT的多级孔结构和疏水界面。eCO₂RR实验结果表明,CNT的引入提高了催化剂的导电性,优化后的复合材料有效地降低了反应的起始电位。在-1.1 V (相对可逆氢电极(RHE))电位下,CO部分电流密度为15.6 mA·cm^-2,ZIF-8-50@CNT催化剂的比表面活性提升了3.5倍(相比ZIF-8-50),塔菲尔斜率降低到136 mV·dec^-1。并且产物CO的选择性和稳定性得到了提高,在宽电势窗口-0.9~-1.2 V (vs RHE)内,CO的法拉第效率(FE)保持在80%以上。在10 h稳定性测试中,催化剂活性保持稳定,整体增强了复合材料eCO₂RR的性能。     

过渡金属氧化物和金属负载型沸石催化剂上合成 纳米碳管及其表征

采用气相催化沉积法催化合成纳米碳管,比较了不同金属氧化物和金属负载型沸石催化剂以及不同分子筛载体对合成纳米碳管的影响,并用TEM,XRD表征其形貌和结晶度,用DTA-TG考察了纳米碳管的热和稳定性。实验结果表明纳米碳管的形成除了与金属种类有关外,还直接与催化剂的颗粒大小和分散状态有关。粒径在20nm左右的不规则形状的纳米粒子是形成纳米碳管的活性组分,非负载和负载型的催化剂均表明活性组分的粒径与纳米碳管的管径有一定的对应关系。化学提纯后能得到高纯度的纳米碳管;其管壁具有较好的石墨化结构,在空气中的热稳定性大于400℃,而在氮气中能维持到1200℃以上。     

碳纳米管改性g-C3N4提升可见光催化降解性能

以尿素为原料,引入少量的多壁碳纳米管(CNT)改性,采用简便方法制备CNT/g-C_3N_4催化剂。利用扫描电镜(SEM)、透射电镜(TEM)、傅里叶红外光谱仪(FT-IR)、X射线衍射(XRD)、X射线光电子能谱(XPS)、紫外-可见-近红外分光光度计(UV-Vis-NIR Spectrophotometer)、荧光光谱(PL)等手段对CNT/g-C_3N_4催化剂进行表征。结果表明,g-C_3N_4与CNT之间的协同作用,影响了gC_3N_4的能带结构,增强了其对可见光的吸收,改善了光生载流子的分布,提高了电子-空穴对的分离效率。并以罗丹明B(RhB)水溶液模拟废水,在可见光下考察催化剂的光催化降解性能,发现当CNT掺杂量为0.1%(w/w)时效果最佳,降解速率常数是体相g-C_3N_4的3.1倍,且研究发现超氧自由基是该体系下的主要活性物种。     

Synthesis and characterization of multiwall carbon nanotubes/alumina nanohybrid-supported cobalt catalyst in Fischer-Tropsch synthesis

Multiwall carbon nanotubes (MWNTs) and alumina are combined to give a new type of nanohybrid for Fisher-Tropsch synthesis (FTS) catalyst support. Alumina nano-particles (10 wt%) were introduced directly on functionalized MWNTs by a modified sol-gel method. Microstructure observations show that alumina particles were homogeneously dispersed on the inside and outside of modified MWNTs surfaces. 15 wt% cobalt loading catalysts were prepared with this nanohybrid and γ-alumina as a reference, using a sol-gel technique and wet impregnation method respectively. These catalysts were characterized by TEM, XRD, N₂-adsorption, H₂ chemisorption and TPR. The deposition of cobalt nanoparticles synthesized by sol-gel technique on the MWNTs nanohybrid shift the reduction peaks to a low temperature, indicating higher reducibility for uniform cobalt particles. Nanohybrid also aided in high dispersion of metal clusters and high stability and performance of catalyst. The proposed MWNTs nanohybrid-supported cobalt catalysts showed the improved FTS rate (g_HC/(g_cat·min)), CO conversion (%), and water gas shift rate (WGS)(g_CO2/(g_cat·h)) of 0.012, 52, and 30E-3, respectively, as compared to those of 0.007, 25, and 18E-3, respectively, on the γ-alumina-supported cobalt catalysts with the same Co loading.     

不同金属改性Ni/KIT-6催化剂的制备及其甲烷化性能研究

采用共浸渍法分别制备了用Mg、Ce、V、La金属改性的Ni/KIT-6催化剂,用于CO₂甲烷化反应的研究。利用N₂吸附-脱附、X射线衍射、H₂程序升温还原、H₂程序升温脱附、透射电镜手段对催化剂进行了表征,考查了不同金属助剂对Ni/KIT-6的影响。结果表明,在KIT-6载体上活性金属和助剂的分散度都非常高,Ni粒子的分散度主要取决于KIT-6载体高度有序的介孔结构的限域作用,不受助剂金属添加的影响。各助剂金属的加入几乎不影响Ni/KIT-6催化剂的表面形貌,但对Ni金属还原的难易程度和还原度有影响。在研究的几种金属中,V金属使催化剂中Ni金属的还原最容易,还原度更高,且V金属的氧化物具有改变CO₂反应机理的作用,使得甲烷化反应进行的最好。用V改性后的催化剂与未改性的催化剂相比,CO₂的转化率提高了3.7%,CH₄的选择性提高了11.6%,CH₄的选择性达到了100%。     

Preparation and characterization of Pt/C catalysts for PEMFC cathode: effect of different reduction methods

Three Pt/C catalysts for PEMFC cathode were prepared by impregnation-reduction method using HCHO, NaBH₄, and N₂H₄ as reductant, respectively, and characterized by BET, CV and XRD. The effect of reduction methods on the activity of catalysts was investigated. Compared with NaBH₄ and N₂H₄, HCHO is the most suitable one among the three reductants. The catalytic activity for oxygen reduction is in the order Pt(HCHO) > Pt(NaBH₄) > Pt(N₂H₄). This revised version was published online in June 2006 with corrections to the Cover Date.     

Heck reactions with various types of palladium complex catalysts: application of multiphase catalysis and supercritical carbon dioxide

The application of multiphase catalytic systems for palladium catalyzed Heck reactions brings several benefits such as easy catalyst-product separation and catalyst recycling. The effective multiphase Heck systems can be prepared by using different types of catalyst phases, including biphasic catalysis and supported liquid phase catalysts, and a new generation solvent of supercritical carbon dioxide.     

高分散Fe-N-C氧还原反应电催化剂及其在直接甲醇燃料电池中的应用

氧还原反应(ORR)是燃料电池和金属空气电池等洁净发电装置中阴极的主要反应,该反应动力学过程慢,电化学极化严重. Pt基电催化剂具有较好的ORR活性,然而Pt资源有限、价格昂贵,研制高活性、低成本的代Pt电催化剂意义重大.经过几十年的探索,研究者发现将含有C, N和Fe等元素的前体进行高温热处理得到的Fe-N-C电催化剂对ORR具有良好的活性,然而在高温热解过程中Fe容易发生聚集而形成大块颗粒,导致Fe的利用率不高,影响了电催化剂的ORR活性.
　　本文分别以聚吡咯和乙二胺四乙酸二钠(EDTA-2Na)为C和N的前驱体,利用高温热解形成的富含微孔的碳材料对铁前体的吸附及锚定作用,获得了一种Fe高度分散的Fe-N-C电催化剂.采用物理吸脱附技术、高分辨透射电镜(HRTEM)和扫描电镜对Fe-N-C及其制备过程中相关电催化剂的孔结构及表面形貌进行了表征.结果表明,在第一步热解过程中, EDTA-2Na的Na对碳材料起到了活化作用,形成富含微孔的N掺杂碳材料(N-C-1),其BET比表面积达到1227 m2/g,孔径约1.1 nm.在第二步热解过程中, N-C-1有效地抑制了Fe的聚集,产物Fe-N-C中的Fe元素均匀地分布在碳材料中,其比表面积高达1501 m2/g.
　　电化学测试结果表明,在碱性介质(0.1 mol/L NaOH)中, Fe-N-C电催化剂对ORR具有良好的催化活性, ORR起始电位(Eo)为1.08 V (vs. RHE),半波电位(E1/2)0.88 V,电子转移数n接近4, H2O2产率<3%,与商品20%Pt/C(Johnson Matthey)接近.电化学加速老化测试结果表明, Fe-N-C的E1/2未发生明显变化,而Pt的负移45 mV,表明Fe-N-C具有很好的稳定性;在酸性介质(0.1 mol/L HClO4)中, Fe-N-C的Eo为0.85 V, E1/2为0.75 V,其E1/2比Pt/C负移约0.15 V,表明在酸性介质中Fe-N-C对ORR的催化活性还有待提高.采用TEM、X射线衍射、X射线光电子能谱以及穆斯堡尔谱等方法研究了电催化剂构效关系.结果表明, Fe-N-C较好的ORR活性主要来自于高分散的Fe-N4结构,此外, N(吡啶N和石墨N)掺杂的C也对反应具有一定的催化活性.
　　与Pt/C相比, Fe-N-C电催化剂具有很好的耐甲醇性能.本文对比了Fe-N-C和Pt/C作为阴极催化剂的直接醇类燃料电池(DMFC)性能,采用质子交换膜的DMFC最大功率密度分别为47(Fe-N-C)和79 mW/cm2(Pt/C),而采用碱性电解质膜的则分别为33(Fe-N-C)和8 mW/cm2(Pt/C).结合半电池结果表明, Fe-N-C电催化剂在碱性介质中具有比Pt更为优秀的催化活性和稳定性,有望用作DMFC阴极代Pt催化剂.     

Li4Ti5O12/CMK-3复合材料的制备及其作为锂离子电池负极材料的性能

将LiNO₃和Ti(OC₄H₉)₄填填充在有序介孔碳CMK-3 孔道中, 然后烧结合成了Li₄Ti₅O₁₂/CMK-3复合材料. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)对其结构和微观形貌进行了表征. 利用差热-热重分析(TG-DTA)测试复合材料中Li₄Ti₅O₁₂的含量. 利用充放电测试、循环伏安和电化学阻抗技术考察了复合材料作为锂离子电池负极材料的性能. 发现Li₄Ti₅O₁₂分布在CMK-3孔道中及其周围, 复合材料的高倍率充放电性能显著优于商品Li₄Ti₅O₁₂, 复合材料中Li₄Ti₅O₁₂的比容量明显高于除去CMK-3的样品(在1C倍率时比容量为117.8 mAh·g^-1), 其0.5C、1C和5C倍率的放电比容量分别为160、143 和131 mAh·g^-1, 库仑效率接近100%, 5C倍率时循环100次的容量损失率只有0.62%. 本研究结果表明CMK-3明显提高了Li₄Ti₅O₁₂的高倍率充放电性能, 可能是CMK-3特殊的孔道结构和良好的导电性减小了Li₄Ti₅O₁₂的粒径并提高了其电导率.     

铝源对Ni/Al2 O3催化剂结构及其CO2-CH4重整性能的影响

以三种不同铝源采用溶液燃烧法制备了系列Ni/Al_2O_3催化剂,通过XRD、H_2-TPR、NH_3-TPD、N_2吸附-脱附、TGDTG和TPH等分析方法对反应前后催化剂进行了表征,研究了铝源对Ni/Al_2O_3催化剂结构、表面性质及其CO_2-CH_4重整性能的影响。结果表明,以Al(NO_3)_3·9H_2O为铝源制备的NiNO-AlNO催化剂比表面积较大,达102 m~2/g;高温还原峰面积大,峰型更为弥散;且载体Al_2_O_3具有一定的结晶性。而以Al_2(SO_4)_3·18H_2O和AlCl_3·6H_2O为铝源制备的NiNO-AlSO和NiNO-AlCl催化剂,其载体以无定型Al_2O_3存在,活性组分Ni晶粒粒径大、分散性差,还原峰面积较小,与载体的相互作用较弱。其中,由于硫酸铝较为稳定,需要在更高温度下才能转化为Al_2O_3,且所制备NiNO-AlSO催化剂中残留有含硫物质,使得其表面酸性较强。评价结果显示,NiNO-AlNO催化剂活性较高,稳定性好,CH4转化率为31.21%,CO_2转化率为48.97%。积炭分析结果发现,NiNO-AlNO催化剂表面积炭量最少,沉积炭主要以无定型态存在,具有良好的抗积炭性能。     

An investigation into the electro-oxidation of ethanol and 2-propanol for application in direct alcohol fuel cells (DAFCs)

A comparative study of the electro-oxidation of ethanol and 2-propanol was carried out on carbon-supported platinum particles. Cyclic voltammetry, steady state polarisation, and electrochemical impedance spectroscopy were used to investigate the oxidation reactions. A difference in the mechanistic behaviour of the oxidation of ethanol and 2-propanol on Pt was observed, thereby highlighting the fact that the molecular structure of the alcohol has great influence on its electroreactivity. The study emphasizes the fact that 2-propanol is a promising fuel candidate for a direct alcohol fuel cell.     

SO_2对Mn-Ce/TiO_2低温SCR催化剂的毒化作用研究

考察了SO_2对Mn-Ce/TiO_2低温脱硝催化剂活性的影响,利用XRD、BET、SEM和XPS对其毒化作用的原因进行分析。结果表明,SO_2对催化剂活性有明显的抑制作用,使NO_x去除率由84%降至42%左右。主要是SO_2的加入造成催化剂比表面积减小,孔径为5-10 nm的孔数量减少,且催化剂晶相由锐钛矿型转化成金红石型结构,活性组分MnO_x发生晶化现象,破坏了Mn-Ti间的强相互作用。催化剂理化性质的变化造成吸附态氧转化为晶格氧的路径受阻、MnO_2含量减少和CeO_x储氧功能减弱,并且产生氧阻效应而使NO吸附和解吸受阻,造成催化剂活性降低。同时生成的硫酸铵盐在催化剂表面沉积,覆盖了催化剂表面的Lewis酸性位,使其对NH_3吸附能力减弱。     

氮掺杂碳纳米管负载Co3O4氧还原电催化剂的制备与性能

以碳纳米管(CNT)为原料,通过负载维生素B₁₂,简单热解得到了一种氮掺杂碳纳米管(N/CNT)负载低含量Co₃O₄纳米颗粒的氧还原电催化剂(Co₃O₄@N/CNT)。得益于均匀分散的Co₃O₄纳米颗粒以及氮掺杂,Co₃O₄@N/CNT表现出了优异的氧还原催化性能,其半波电位达到了0.844 V(vs RHE),超越了商业Pt/C(0.820 V(vs RHE))。与Pt/C相比,基于Co₃O₄@N/CNT组装的锌-空气电池表现出了更优的放电性能和循环稳定性。