Reference materials and certified reference materials for spectrometry in Romania

Several reference materials (RMs) and certified reference materials (CRMs) are widely used in Romania as measurement standards in different spectrochemical measurements. Among them, single element standard solution certified for their mass concentration play a key role in ensuring the required traceability of results expressed in this measurement unit. A short review of the locally available elemental RMs and CRMs used in atomic spectrometry or in other analytical techniques where aqueous standard solutions are required (usually called RMs or CRMs for spectrometry) is given. The experience of the INM in preparation and certification of such materials is described. Some aspects regarding their use for ensuring the accuracy and for confirmation of the traceability of analytical measurements, especially through calibration and metrological validation of main instrument performances, are discussed.     

Reference materials and certified reference materials for water and food microbiology

Summary The concept of Certified Reference Materials (CRMs) for the verification of the accuracy of analytical methods and the traceability of the results to a CRM, is well accepted in chemistry. The use of Reference Materials (RMs) for intra-laboratory quality control schemes or for round-robin and proficiency testing is well established and follows from certain norms (ISO 9000 and EN 45000 series). For microbiology such concepts have not been fully defined and RMs are only rarely used. CRMs do not exist. To fill this gap the Commission of the European Community, through the BCR programme, has launched projects in collaboration with the RIVM (National Institute of Public Health and Environmental Protection) in Bilthoven (NL). Following fundamental considerations and feasibility studies, several intercomparisons have been held using selected laboratories working with food or water microbiology. Various microbiological strains have been subject of studies: Salmonella typhimurium, Listeria monocytogenes, Bacillus cereus, Staphylococcus aureus for food, Escherichia coli, Enterococcus faecium, Enterobacter cloacae and Staphylococcus warneri for water. To produce materials for interlaboratory studies, a set of milk powders was prepared by spray-drying. Separate portions were contaminated with one of the strains mentioned. The materials were then encapsuled in gelatine. It has been demonstrated that if protected in milk powder matrices, bacteria maintain the ability to be revived, but do not multiply. The modes of evaluation of the results for homogeneity and stability differ from those commonly used in chemistry.     

NIES certified reference materials for arsenic speciation

 The National Institute for Environmental Studies (NIES) recently prepared two candidate certified reference materials (CRMs) for arsenicals to meet the growing demand for the quality assurance of arsenic speciation analysis. The NIES candidate CRM No. 14 Brown Alga was prepared from Hijiki seaweed for the certification of inorganic arsenic content, and No. 15 Scallop was prepared from adductor muscle of scallop for the certification of arsenobetaine content. The preparation of the candidate CRMs is briefly described. Cooperative analyses for total arsenic content of the candidate CRMs have been underway. The preliminary speciation analysis at NIES revealed difficulty in establishing suitable conditions for extracting arsenic species from the materials. Chromatograms of arsenic species by a high performance liquid chromatography-inductively coupled plasma mass spectrometric detection system are presented to provide information about arsenic species present in these candidate CRMs.     

Accreditation and the need for certified reference materials

The comparability of data from accredited laboratories is not always as good as customers would desire. A number of reasons for this fact are given. Clients of laboratories do not specify methodology, which may lead to the application of systematically different methods or to methodology with improper performance characteristics. Laboratories do not always validate methodology sufficiently which is, however, among others provoked by a lack of reference materials. It is argued that accreditation cannot enforce comparability on itself, but needs to be embedded in a measurement infrastructure. The quality systems which underly accreditation form a basic element. In addition, adequate methods, good laboratory performance studies and certified reference materials are required.     

Availability of reference materials: COMAR the database for certified reference materials

COMAR is the international database for certified reference materials. A new user-friendly web-based version, COMAR², has been developed by BAM and CONET Consulting AG which will be available in December 2002. The advantages of COMAR² are briefly explained.Presented at the International ILAC/IAF Conference on Accreditation in Global Trade, 23-25 September 2002, Berlin, Germany     

Uranium isotope dilution mass spectrometry using NBL certified reference materials as spikes

The isotope dilution mass spectrometry method of analysis is used to determine the elemental uranium contents in a wide variety of uranium bearing materials. The method is based on the mass spectrometric analysis of a mixture prepared by diluting the sample to be analyzed with a spike of distinctly different isotopic composition to that of the sample. In this work, a beginning is made to identify suitable candidates among the multitude of certified reference materials (CRMs) available at the New Brunswick Laboratory to supplant the use of ²³³U which remains now as the preferred spike nuclide. The results of the study presented here identify CRM 112-A (of normal isotopic composition) and CRM 115 (depleted uranium composition) as suitable candidates to replace ²³³U as spike material for determining uranium in high enriched uranium materials, and CRM 116 (²³⁵U mass fraction of >90 %) for determining uranium in materials of low enrichment.     

Application of isotope dilution mass spectrometry to research of certified reference materials

This paper briefly describes the method and applications of isotope dilution mass spectrometry(IDMS). Primary standard solutions with various natural isotope abundances were used to certify the concentration of enriched isotope solutions by IDMS. Then these enriched isotopes were used to certify unknown samples by IDMS. Li, K, Mg, Fe, Cu, Ni, Cd, Mo, Pb, etc in CRMs were certified and very good results were obtained in three international comparisons by IDMS. Received: 15 June 2000 Accepted: 26 October 2001     

BCR certified reference materials for reactor neutron dosimetry

A series of reference materials intended for use as activation or fission monitors for neutron fluence rate measurements has been prepared by the Joint Research Centre of the European Commission. Certification has been carried out by expert European laboratories and distribution of the certified reference materials (CRMs) is through the BCR programme of the Commission. The list (18 CRMs) includes materials to cover the complete energy spectrum, and suitable for different irradiation times. Fission monitors are ²³⁸UO₂ or ²³⁷NpO₂ in the form of microspheres. Activation monitors are high purity metals (Ni, Cu, Al, Fe, Nb, Rh, or Ti), certified for interfering trace impurities, or dilute aluminium-based alloys, where aluminium is chosen as a suitable matrix for reducing the neutron self-shielding effect. Newly certified materials are IRMM-530R Al-0.1%Au, replacing the exhausted IRMM-530 material, used as comparator for k ₀-standardization, and three new Al-Co alloys (0.01-1%Co). Two others, in the process of certification are Al-0.1%Ag and Al-2%Sc for thermal and epithermal fluence rate measurements. Other candidate reference materials currently being certified are two uranium-doped glass intended for dosimetry by the fission-track technique.     

A measure for assessing certified reference ores and related materials

Experience in the certification of a number of Canadian reference ores and related materials has shown that their quality or usefulness in particular analytical applications can be evaluated objectively in terms of a so-called certification factor. This factor is defined as the ratio of the relative confidence interval of the interlaboratory consensus value for a selected element, expressed as a percentage, to the mean of the within-laboratory coefficient of variation. It is proposed that for a material to be acceptable (certifiable), its certification factor(s) must be 4.     

Uncertainty limits for certified values of standard reference materials

Summary Uncertainty limits usually employ the 95% confidence limits and should include allowances for the uncertainty of known sources of systematic errors of the measurements. But in many cases, when an interlaboratory comparison study is used for certification purposes of standard reference materials, only the 95% confidence limits are considered and given as the uncertainty limit. In this work, we shall show the results as the number of mean values (n) reported vary and only the 95% confidence limits are considered, using as an example the intercomparison study on IAEA/SL-3/lake sediment sample. And finally, we shall compare the results if only the 95% confidence limits are considered with those of the standard deviation and propose when n is large that the standard deviation should be employed instead of the 95% confidence limits as the uncertainty limits, if the other systematic and random errors are not included.     

New Japanese certified reference materials for electrolytic conductivity measurements

Accreditation and Quality Assurance - The National Metrology Institute of Japan (NMIJ) has established three certified reference materials (CRMs) in electrolytic conductivity with a primary...     

人参皂苷Re标准样品的研制

以藏药诃子为原料,研制诃黎勒酸国家标准样品. 诃子经60%乙醇提取,大孔树脂富集,制备液相色谱技术得到诃黎勒酸标准品. 采用高效液相色谱（HPLC）、液相色谱-质谱（LC-MS）和薄层色谱（TLC）等手段进行纯度分析. 采用紫外光谱（UV）、红外光谱（IR）、高分辨质谱（MS）和核磁共振波谱（NMR）技术进行结构确认. 最后进行均匀性、稳定性和联合定值. 结果表明,诃黎勒酸样品均匀性良好,4 ℃储存,24个月内稳定. 联合定值确定诃黎勒酸纯度标准值为99.33%,符合国家标准品的要求. 研制出的诃黎勒酸（GSB 11-3724-2020）国家标准样品,可用于含量测定、检测方法评定、相关产品的检测与质量控制.     

Accreditation system for reference material producers and certified reference materials for iron and steel in Japan

  ISO 9000 series strictly requires traceability to national or international measurement standards. It is becoming more necessary to make clear the concept of traceability of measurement standards with respect to chemical composition and to accredit the reference material producers. In Japan, the accreditation system for reference material producers is considered to satisfy the requirement of ISO Guide 34, ISO 9000 series and ISO/IEC Guide 25, while the producer fulfills the concept of traceability of measurement standards. This paper describes the production of iron and steel reference materials in Japan relating to the international standardization of methods (written standards) and accreditation of reference material producers. Received: 11 October 1996 Accepted: 5 December 1996     

Production and certification of environmental reference materials in Romania

Preparation techniques for single-element and multielement standard solutions, with special emphasis on the potential progress in this field are presented. A short review of locally available reference materials is given. Some aspects of the experience accumulated in Romania regarding the various certification approaches of reference materials are presented and the main characteristics of these certified reference materials are listed. Received: 23 May 1997 / Revised: 15 August 1997 / Accepted: 15 August 1997     

Trends in certified reference materials for the speciation of trace elements

The measurement of the chemical species of elements (instead of the total element concentration) has become an irreversible trend in analytical chemistry. The motivation lies in the fact that the biochemical and geochemical behaviour of an element is governed by its species. Quality assurance of the analytical procedures used for speciation analysis requires the analysis of representative reference materials, certified for the relevant species. Up to now the number of existing certified reference materials for trace element species is very limited. The most important ones are environmental CRMs certified for trialkyltin compounds, methylmercury, Cr(III)/Cr(VI) and food CRMs certified for arsenic species and methylmercury. Major developments are to be expected in CRMs focussed on environmental problems, including waste treatment, on bioavailability of trace elements in food and on bio-monitoring in occupational health and hygiene. It is, however, unlikely that the producers of CRMs will ever be able to cover all needs. Add to this that many, very active species are notoriously unstable and/or short living and require in-situ analysis. This will lead to different analytical developments, such as analyses in-situ, where the classical concept of CRMs may not stand firm anymore.     

The use of inductively coupled plasma mass spectrometry in the production of environmental certified reference materials

The use of inductively coupled plasma mass spectrometry (ICP-MS) in the production of environmental certified reference materials by the National Research Council of Canada is reviewed. Particular emphasis is placed on the use of isotope dilution ICP-MS. Results for fresh and saline natural waters, fish tissues and sediments are presented to illustrate the impressive capabilities of this technique.     

New certified reference materials and proficiency test for environmental radioactivity measurements

A reliable determination of natural and anthropogenic radionuclides in environmental samples is necessary to comply with the radiation protection and environmental regulations. This paper presents the results of the characterisation of massic activities of natural and anthropogenic radionuclides in soil and water matrices produced as test items to conduct the proficiency test ERAD-PT-2013. The proficiency test ERAD-PT-2013 was designed to investigate analytical performance in analysing both natural and anthropogenic radionuclides, to assist laboratories to identify analytical problems, and to improve the quality of measurement results. The proficiency test items, their spectral interferences and the activity concentration levels of the analytes were designed in a way to enable identification of potential analytical problems. Methodologies, data evaluation approach and evaluation of proficiency test results for each radionuclide are described and discussed.