大气温室效应的一维辐射传热分析

大气中温室气体对地面长波热辐射的吸收和再发射导致了温室效应.计算了大气不同高度200～50000 cm-1(0.2～50 μm)光谱吸收系数,采用一维大气介质模型和射线踪迹-节点分析法(RTNAM)的多层模型对大气中二氧化碳及水蒸气不同浓度情况下的大气温度进行了计算.结果表明标准大气CO2浓度增加1倍,对流层的温度上升...     

升温Ta+N双注入对硬质合金性能的影响

利用升温离子注入技术 ,在PSII装置中实现了N +Ta双注入对硬质合金的有效表面改性 ,注入剂量为8× 10 1 7ions·cm- 2 ,注入表面温度分别为 10 0℃和 40 0℃。用显微硬度计测定硬度 ,表明试样表面显微硬度均有提高 ,其中 40 0℃试样表面显微硬度提高最大 ,高达 2 0 0 %。用俄歇电子能谱分析元素的浓度剖面 ,发现把温度从 10 0℃提高到 40 0℃ ,其注入层深度显著增加。X射线衍射测出了注入层表面形成的WN、TaN析出相。升温双元离子注入取得升温单元离子注入改性同样的效果 ,并获得比单元注入更好的复合优化强化层     

基于气象参数戈壁沙漠地区近地面大气湍流建模

 提出一种适合戈壁沙漠地区的近地面大气湍流模型。通过测量近地面层不同高度处温度、湿度、压强和风速等常规气象参数,结合模型可给出近地面层大气湍流强度。模型计算的近地面层大气湍流强度通常白天值最大,中午前后出现较宽的最大值区间,在日出时段和日落时段出现较明显的最小值,夜间呈不规则变化,该结果能够很好地反映近地面层大气湍流强度的变化特性。在影响大气湍流强度变化的参数中,大气温度的变化趋势直接影响着大气湍流强度的变化：通常白天大气温差较高时,大气湍流强度较强;大气温差较低时,大气湍流强度较弱;大气温差起伏较大的时刻,大气湍流强度的变化也会较大,大气温差起伏趋势与大气湍流强度变化趋势有相似之处。     

CVD法制备碳纳米管的TG-DTA研究--温度对CVD法制备碳纳米管的影响

基于碳纳米管粗产品中无定形碳和不同直径碳纳米管对氧的反应活性的差异 ,通过差热 -热重 (TG DTA)方法 ,结合透射电镜 (TEM)和X射线衍射 (XRD)的测试结果 ,研究了合成温度对以乙炔气体为碳源 ,用CVD法制备碳纳米管的石墨化程度、碳纳米管直径以及直径分布的影响 .结果表明 :反应中 ,由于催化剂Co/SiO2中活性组分 (Co)微晶随合成温度的升高而增大 ,导致所制备的碳纳米管的直径增大 ,从 2 0～ 30nm (6 5 0℃ )增加到 30～ 5 0nm (75 0℃ ) .碳纳米管的石墨化程度随着反应温度的升高而增加 .XRD实验结果还表明 ,当合成温度从 6 5 0℃增加到 85 0℃时 ,2θ值从 2 5 .8°增加到 2 6 .8°,(0 0 2 )晶面的层间距从 3.45 减小到 3.32 ,即随着合成温度的升高 ,碳纳米管 (0 0 2 )晶面的层间距减小 .通过DTA放热峰的峰温和半峰宽的分析得出 ,无定形碳的放热峰峰温Tp<380℃ ,其含量随着温度的升高而减小 .碳纳米管的DTA放热峰的峰温Tp 随着碳纳米管的直径和石墨化的程度的增加而升高 ,半峰宽随着碳纳米管的直径的分布范围增大而增宽 .低温 (6 5 0℃ )有利于生成直径小且均匀的多层碳纳米管 (2 0～ 30nm) ,而高温 (大于 75 0℃ )则有利于生成直径大的多层碳纳米管 (大于 30～5 0nm) .     

氟化氢泛频20P4,20P5激光谱线大气传输性能实验

采用氟化氢泛频化学激光器作光源 ,在室外实际大气中测量了氟化氢泛频激光 2 0P4、2 0P5谱线的大气透过率 ,分析计算了其大气消光系数和大气吸收系数。实验表明氟化氢泛频激光处于大气传输窗口边缘 ,其谱线的大气传输性能差异很大 ,证实了 2 0P4是氟化氢泛频选频的首选谱线     

颗粒帘换热器中气粒两相换热特性实验研究

根据某1 t/h燃煤工业锅炉空气预热器的热力参数,设计并搭建了一套颗粒帘空气预热器模拟实验系统,研究了不同进气温度Tg0(150~300℃)、进气速度Vg0(0.9~1.5m/s)、颗粒帘进口厚度b0 (60~180 mm)、颗粒粒径dp(150~212μm)以及不同颗粒质量流量ms (550~2150 g/s)工况条件下热空气与进口温度tp0=20℃的硅砂颗粒帘间的换热特性。结果表明:影响颗粒帘换热器中气粒两相换热特性因素的重要性次序为进气温度、进气速度、颗粒质量流量、颗粒粒径、颗粒帘进口厚度;换热端差最低可至4.5℃,最大可达87℃;颗粒帘及颗粒帘出口气流的温度沿颗粒下落方向在前期上升迅速(186~475℃/m)而后期上升比较缓慢(60~108℃/m),并且在0~0.5 m和0.5~1.0 m的高度范围可分别用线性和对数方程来描述。     

燃煤易挥发微量重金属元素行为的试验研究

为了解煤燃烧过程中易挥发微量重金属元素的行为及其控制因素,对黔西南烟煤和无烟煤进行了层燃实验和流化床燃烧实验。结果表明,层燃实验,煤中Hg在150℃挥发率达50.25％。到815℃几乎全部释放,Se的挥发率平均在98％以上。950℃下煤中As、Sb的挥发率平均为36.77％和34.47％。流化床燃烧,煤中绝大部分Hg以气态排放到大气中,部分Se以气态排放;微细颗粒吸附Hg、Se、As和少量的Sb以吸附态排放。赋存状态、燃烧方式以及燃烧工况等对微量重金属的挥发性有明显的控制作用。     

对流层大气温度高度廓线半定量估算

一般大学物理教材中都有求解出地球表面温度的例子或习题,能否扩展到估算对流层大气温度随高度而降低的规律?本文探索建立了地球和对流层分层大气模型,依据最新的大气吸收率、辐射率来计算分层大气的相关参数,再利用辐射能量平衡和斯特藩-玻尔兹曼定律,估算对流层温度高度廓线.计算结果表明:对流层分为5层时,估算出的地球表面温度和各层大气温度,与美国标准大气模型中地球表面温度及对流层大气温度随高度降低率6.5 K/km符合较好.     

太阳多层共轭自适应光学系统的性能优化

为克服大气非等晕的影响,多层共轭自适应光学(MCAO)系统被广泛应用于太阳望远镜,以有效扩大校正视场。仅考虑由于大气非等晕造成的系统理论误差,研究了变形镜(DM)个数及其共轭高度对太阳多层共轭自适应光学(MCAO)系统性能的影响。结果表明,MCAO系统中DM的最佳共轭高度取决于大气湍流的分布;理论上,太阳望远镜(D/r0=28.57)视场为1arcmin时,只需两块DM,太阳MCAO系统斯特列尔比(SR)可达0.55,基本满足太阳望远镜的观测要求;同时,随着太阳望远镜口径的增大,需通过增加DM个数以满足其在大视场观测的需求。     

利用［Fe/Pt］n多层膜降低L10-FePt有序化温度

采用直流磁控溅射方法制备了Fe/Pt多层膜和FePt单层薄膜，再经不同温度真空热处理得到 了有序相L10₀-FePt薄膜.通过x射线衍射谱和磁性研究表明，FePt单层薄膜需 要在500℃ 以上热处理，才能开始有序化转变，而Fe/Pt多层膜可以降低FePt薄膜有序化温度.［Fe(1 5nm)/Pt(15nm)］13₁₃薄膜在350℃热处理后，有序度已经增加到 06，相应矫 顽力达到了501kA/m.多层膜化促进有序化在较低的温度下进行，这是由于热处理过程中多 关键词： 0-FePt有序相')" href="#">L10₀-FePt有序相 磁控溅射 有序度 Fe/Pt多层膜     

Study on the radiation problem caused by electron beam loss in accelerator tubes

The beam dynamic code PARMELA was used to simulate the transportation process of accelerating electrons in S-band SW linacs with different energies of 2.5, 6 and 20 MeV. The results indicated that in the ideal condition, the percentage of electron beam loss was 50% in accelerator tubes. Also we calculated the spectrum, the location and angular distribution of the lost electrons. Calculation performed by Monte Carlo code MCNP demonstrated that the radiation distribution of lost electrons was nearly uniform along the tube axis, the angular distributions of the radiation dose rates of the three tubes were similar, and the highest leaking dose was at the angle of 160° with respect to the axis. The lower the energy of the accelerator, the higher the radiation relative leakage. For the 2.5 MeV accelerator, the maximum dose rate reached 5% of the main dose and the one on the head of the electron gun was 1%, both of which did not meet the eligible protection requirement for accelerators. We adopted different shielding designs for different accelerators. The simulated result showed that the shielded radiation leaking dose rates fulfilled the requirement.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Modification to first-order Born approximation for improved prediction of scattered sound from weakly scattering objects

When deriving the Fourier diffraction theorem based on the first-order Born approximation,the difference between wave number of the scattering object and that of the surrounding medium is ignored,causing substantial errors in sound scattering prediction.This paper modifies the Born approximation by taking into account the amplitude and phase changes between the scattering object and the water due to the wave number difference.By changing the radius and center position of the sampling circle in the Fourier domain,accuracy of the predicted sound scattering is improved.With the modified Born approximation,the computed far-field directional pattern of the scattered sound from a circular cylinder is in good agreement with the rigorous solution.Numerical calculations for several objects with different shapes are used to show applicability and effectiveness of the proposed method.     

Collective effects for long bunches in dual harmonic RF systems

The storage of long bunches for large time intervals needs flattened stationary buckets with a large bucket height.Collective effects from the space charge and resistive impedance are studied by looking at the incoherent particle motion for the matched and mismatched bunches.Increasing the RF amplitude with particle number provides r.m.s wise matching for modest intensities.The incoherent motion of large amplitude particles depends on the details of the RF system.The resulting debunching process is a combination of the too small full RF acceptance together with the mismatch,enhanced by the collective effects.Irregular single particle motion is not associated with the coherent dipole instability.For the stationary phase space distribution of the Hofmann-Pedersen approach and for the dual harmonic RF system,stability limits are presented,which are too low if using realistic input distributions.For single and dual harmonic RF system with d＝0.31,the tracking results are shown for intensities,by a factor of 3 above the threshold values.Small resistive impedances lead to coherent oscillations around the equilibrium phase value,as energy loss by resistive impedance is compensated by the energy gain of the RF system.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Analysis of Laser-generated Rayleigh wave on viscoelastic materials

In order to understand the viscoelasticity of material, this research has been conducted to study the propagation characteristics of viscoelastic Rayleigh wave theoretically. A model is presented for the pulsed laser generation of ultrasound on viscoelastic medium surface. Referred to the Kelvin model, the frequency equation and the normal displacement of viscoelastic Rayleigh wave were derived, the influence of the viscoelastic modulus on dispersion and attenuation was discussed. From the theoretical calculation, it is shown that the effect of viscoelasticity on the attenuation of Rayleigh wave is more than that on its dispersion. In the case of a weak viscosity, the attenuation of viscoelastic Rayleigh wave is directly proportional to viscosity modulus; the effect of shear viscosity on the attenuation is much more than that of bulk viscosity. The transient response of viscoelastic Rayleigh wave was also simulated using Laplace and Hankel inversion transform, which are showed in good agreement with the theoretic predictions. The model provides a useful tool for the determination of viscoelastic parameters of medium.     

Quantitative analysis results of CE-1 X-ray fluorescence spectrometer ground base experiment

As the nearest celestial body to the earth, the moon has become a hot spot again in astronomy field recently. The element analysis is a much important subject in many lunar projects. Remote X-ray spectrometry plays an important role in the geochemical exploration of the solar bodies. Because of th equasi-vacuum atmosphere on the moon, which has no absorption of X-ray, the X-ray fluorescence analysis is an effective way to determine the elemental abundance of lunar surface. The CE-1 X-ray fluorescence spectrometer (CE-1/XFS) aims to map the major elemental compositions on the lunar surface. This paper describes a method for quantitative analysis of elemental compositions. A series of ground base experiments are done to examine the capability of XFS. The obtained results, which show a reasonable agreement with the certified values at a 30% uncertainty level for major elements, are presented.     

Time domain finite volume method for the transient response and natural characteristics of structural-acoustic coupling in an enclosed cavity

A time domain finite volume method（TDFVM）based on wave theory is developed to analyze the transient response and natural characteristics of structural-acoustic coupling problems in an enclosed cavity.In the present method,the elastic dynamic equations and acoustic equation in heterogeneous medium are solved in solid domains and fluid domains respectively.The structural-acoustic coupling is implemented according to the continuity condition of the particle velocity along the normal direction and the normal traction equilibrium condition on the interface.Several numerical examples are presented to validate the effectiveness and accuracy of the present TDFVM.Then the effects of water depth on the acoustic and vibration characteristics and the natural characteristics of a structural-acoustic coupling system are analyzed.The numerical results show that the increase of water depth leads to a stronger coupling between the water and structure and the decrease of natural frequencies of coupling system,The computational cost and memory of this method are small and it can be applicable to structural-acoustic coupling problems in the heterogeneous fluid.     

A study on the best irradiation dose of X-ray for Hep-2 cells by Fourier transform infrared spectroscopy

Fourier transform infrared spectroscopy (FTIR) was employed to study the human epidermis larynx carcinoma cell lines (Hep-2) which were irradiated by different doses of X-ray.The results show that (1) the irradiation of X-ray damages the structure of the CH3 groups of the thymine in DNA,which restrains the reproduction of Hep-2 cells effectively,(2) the 8 Gy dose of X-ray irradiation changes the framework and the relative contents of some proteins,lipids and the nucleic acid molecules intercellular in the greatest degree,and (3) the 8 Gy dose of X-ray irradiation is the best irradiation dose for lowering the degree of the cancerization of Hep-2 cells according to the criteria for the degree of the cancerization reported recently.Meanwhile,the apoptosis of these cells were detected by using flow cytometry (FCM) primarily.It shows that the apoptotic ratio of the Hep-2 cells depends on the irradiation dose to some extent,but is not linearly.And the apoptotic ratio of the 12 Gy dose group is the maximum (20.36%),but the apoptotic ratios of the 2 to 8 Gy dose groups change little.