Quartz Rod Coated with Modified Silica Gel as a Source of CO and CO2 for Standard Gaseous Mixtures

Quartz rods coated with a thin layer of chemically modified silica gel have been used for the generation of a two-component gaseous standard mixture containing carbon monoxide and carbon dioxide. A new method based on thermal decomposition of immobilized compounds chemically bonded to the surface of silica gel has been used in the generation process. The oxalic acid moiety bonded to the glycydoxypropylsilylated surface of silica gel underwent decarbonylation and decarboxylation at 300°C, yielding carbon monoxide and carbon dioxide. On-line connection of a thermal desorber with the GC/FID enabled calibration of the detector following the process of methanization of CO and CO₂. The following amounts of CO and CO₂ were generated per unit length of the rod: 15.1 × 10⁻⁸ Mol cm⁻¹ (RSD = 5.71%) for CO and 34.2 × 10⁻⁸ Mol cm⁻¹(RSD = 5.16%) for CO₂.     

Characterization of Modified Silica Gel as a Source of Ethene for Standard Gaseous Mixtures

The application of chemically modified silica gel as a source of gaseous standard mixture containing ethene as a measured component is described. The surface of silica gel was chemically modified, which resulted in the formation of N-oxide of diethylaminopropylsilylated silica gel. This compound undergoes thermal decomposition at 245°C, yielding known amounts of ethene. The process of thermal decomposition of chemically modified silica gel took place in a desorber furnace connected on-line via a four-port valve to the device being calibrated. Such a solution provides convenient calibration of a GC/FID system after direct introduction of a stream of the generated mixture onto the front of a GC. It was found that 480 ± 15 mg of ethene can be generated per 1 g of the modified gel.     

The Diphenylacetylene Reaction with Tricarbonylbis(η2-cis-cyclooctene)iron in the Presence or Absence of Carbon Monoxide

Known to be a facile irontricarbonyl transfer reagent, (η²-cis-C₈H₁₄)₂Fe(CO)₃ 1 transfers its Fe(CO)₃ unit to a variety of ligands at low temperature. Stirring a THF mixture of 1 and PhC=CPh under N₂(g) at ?60 °C for 1 h then at room temperature overnight provides mainly a flyover-bridge product [-CPh=CPhC(0)-CPh=CPh-]Fe₂(CO)₆ 2 with the organic bridge on diiron core in a complicated μ-(1,2,5-η³:1,4,5-η³) fashion. The keto fragment in 2 comes presumably from the decomposition of 1 that liberates CO. However, stirring a THF mixture of 1 and PhC=CPh under CO(g) at ?60 °C for 3 h then at room temperature overnight results in [-C(0)CPh=CPhC(0)-]Fe(CO)₄ 3, a compound not isolated in the earlier thermal or photochemical reactions of PhC=CPh with ironcarbonyl. The X-ray structure determinations for both 2 and 3 have been performed.     

New procedure of silica gel surface modification preparation of gaseous standard mixtures for calibration purposes

The new type of silica gel surface modification with using the trimethylamine as a reagent is described. The samples of chemically modified silica gel have been used for generation of gaseous standard mixtures (methyl chloride as a measurand) using the technique of thermal decomposition of the surface compound. The main aim of the research was to check the suitability of the new type of silica gel surface modification for obtaining methyl chloride as a measurand of gaseous standard mixture. The gaseous standard mixture obtained with using this technique was used for calibration of a thermal desorber-gas chromatography-flame ionization detector (TD-GC-FID) system. The homogeneity of coverage of silica gel surface with the immobilized compound has been evaluated. The full uncertainty budget of determination of liberated amount of methyl chloride has been calculated. The average amount of methyl chloride liberated from the unit sample of chemically modified silica gel is 3.59 +/- 0.13 mg g(-1). The influence of the modification way on the amount of liberated analyte has also been determined.     

Development of porosity in carbons from yeast grains by activation with alkali metal carbonates

Cellular structured activated carbon samples were prepared with the aid of alkali carbonates X2CO3 (X = Li, Na, K, Rb, or Cs) from dry bread yeast with a milling procedure. The resultant carbon possesses a very large adsorption amount even for supercritical methane. The activation with Cs2CO3 gave the greatest surface area of 2420 m2 g(-1) from the subtracting pore effect method. The activation efficiency of X2CO3 (X = Li, Na, K, Rb, and Cs) was associated with the order of Gibbs free energy of X2O (X = Li, Na, K, Rb, and Cs) which should play an important role in the gasification. The carbon activated with Rb2CO3 gave the greatest adsorption amount of supercritical methane of 90 mg g(-1) at 0.9 MPa at 303 K.     

Determination of total mercury and methylmercury in human hair by graphite-furnace atomic absorption spectrophotometry using 2,3-dimercaptopropane-1-sulfonate as a complexing agent.

For the determination of total mercury in hair, an amount (25.0 mg) of hair sample was digested with conc. HNO3 (400 microl) at 90 degrees C for 10 min in a 7-ml teflon microreaction vessel. After digestion, the pH of the acidic hair mixture was adjusted to 5.0-6.0 by NaOH and was then passed through a clean-up Sep-Pak C18 cartridge. To the eluate, 2,3-dimercaptopropane-1-sulfonate (DMPS) and sodium acetate buffer (pH = 6.0) were added to form a mercury-DMPS complex. This complex was preconcentrated on two Sep-Pak C18 cartridges in series, and each cartridge was eluted with methanol and adjusted to 2.00 ml. A portion (50 microl) was introduced into a graphite cuvette and then atomized according to a temperature program. The method detection limit (MDL, 3sigma) was 0.064 (microg g(-1)); the calibration graph was linear up to 7.52 microg g(-1). Good accuracies were obtained when testing two human hair certified reference materials (GBW 09101 and BCR-397). Six real samples were analyzed, and the recoveries were 95.8 - 98.2% with a relative standard deviation (RSD, n = 3) < 2.1%. For the determination of methylmercury (CH3Hg+), 25.0 mg of hair sample was extracted with 2.0 mol dm(-3) HCl (1.0 ml) by ultrasonicating for 1 h. The supernatant solution was used for CH3Hg+ analysis and the hair residue was used for the analysis of inorganic mercury (Hg2+). The MDL of CH3Hg+ was 0.068 microg g(-1); the calibration graph was linear up to 6.00 microg g(-1). Six real samples were analyzed, and the recoveries were 96.0-99.2% with RSD (n = 3) < 2.3%. The sum of the concentrations of CH3Hg+ and Hg2+ was very close to that of the total mercury measured with a relative error within 3.6%. The proposed method can be accurately applied to the measurement of CH3Hg+, Hg2+, and total mercury in hair samples.     

双电极法现场快速检测地下水和湖水中碳酸氢根和碳酸根

地下水和湖水中碳酸氢根( HCO-3)和碳酸根( CO2-3)含量是地球化学碳行为和碳循环的重要表征,但两种离子的浓度易受环境影响而改变,因此,地下水和湖水中HCO-3和CO2-3真实含量的测定一直是个难题。实验利用CO2的水解平衡,通过pH电极和二氧化碳电极联用,建立了HCO-3和CO2-3现场快速测定的新方法,解决了地下水和湖水中HCO-3和CO2-3真实含量的测定难题。研究结果表明,在pH=4.8±0.1的底液中, HCO-3和CO2-3的线性范围分别为0.027~570 mg/L和1.25×10-8~39.7 mg/L。共存的金属离子、强酸阴离子(K+、Na+、Mg2+、Cl-、SO2-4,100 mg/L)、弱酸阴离子和弱酸(HSO-3、NO-2、HOAc,50 mg/L)对测定干扰小于5%。实际水样加标实验回收率在95.2%~99.2%之间,相对标准偏差为2.6%~3.7%。与酸碱滴定法进行对比,本方法的准确性良好。但方法受温度影响,因此标准溶液与样品应在同一温度下测量。总体而言,双电极法灵敏、快速、经济且电极携带方便、操作简单、对环境要求不高,十分适合现场和室内一般自然水体的快速检测。本方法已成功应用于青海省地下水和青海湖湖水中HCO-3和CO2-3的现场测定。实验表明,海东地区地下水样品pH在6.4~7.4之间,HCO-3含量为234~4096 mg/L,CO2-3含量为0.16~1.89 mg/L;青海湖湖水样品pH≈8.7,HCO-3含量范围在1.36~1.86 g/L,CO2-3含量在32.3~43.9 mg/L,与文献结果吻合。     

超临界干燥方法对甲烷燃烧催化剂LaMnAl11O19结构及活性的影响

 摘要：用水热合成法制备了锰取代的六铝酸盐催化剂，并比较了超临界干燥法和普通烘箱干燥法对催化剂结构及甲烷燃烧反应活性的影响．DTA－MS结果表明，超临界干燥过程中，催化剂前驱物中的表面铝羟基部分被乙氧基取代．这种表面修饰作用可保持铝分散的均匀性，使催化剂前驱物中碳酸锰和碳酸镧的分解温度明显降低，且氢氧化铝的脱水温度维持在较适宜的范围内；焙烧后，易形成六铝酸盐相．甲烷燃烧反应结果表明，用超临界干燥方法制得的催化剂对甲烷燃烧反应的催化活性明显高于用普通烘箱干燥方法制得的催化剂．     

元素分析仪测定海洋沉积物中的碳酸盐

海洋沉积物中的碳分为无机碳和有机碳,经过高温灼烧除去有机碳后,剩余的碳为无机碳(碳酸盐),其含量可用元素分析仪进行测定。使用国家一级标准物质对灼烧温度和灼烧时间进行了研究,结果表明:样品在420℃灼烧3 h,测定值和推荐值相吻合。方法的检出限为0.058%,测定结果的相对标准偏差为2.54%～3.35%(n=12)。     

Influence of MgO template on carbon dioxide adsorption of cation exchange resin-based nanoporous carbon

In this work, porous carbons with well-developed pore structures were directly prepared from a weak acid cation exchange resin (CER) by the carbonization of a mixture with Mg acetate in different ratios. The effect of the Mg acetate-to-CER ratio on the pore structure and CO(2) adsorption capacities of the obtained porous carbons was studied. The textural properties and morphologies of the porous carbons were analyzed via N(2)/77K adsorption/desorption isotherms, SEM, and TEM, respectively. The CO(2) adsorption capacities of the prepared porous carbons were measured at 298 K and 1 bar and 30 bar. By dissolving the MgO template, the porous carbons exhibited high specific surface areas (326-1276 m(2)/g) and high pore volumes (0.258-0.687 cm(3)/g). The CO(2) adsorption capacities of the porous carbons were enhanced to 164.4 mg/g at 1 bar and 1045 mg/g at 30 bar by increasing the Mg acetate-to-CER ratio. This result indicates that CER was one of the carbon precursors to producing the porous structure, as well as for improving the CO(2) adsorption capacities of the carbon species.     

高效液相色谱法分离/蒸发光散射和紫外检测法测定天麻中天麻甙含量

天麻（Gastrodia elata Blume）系兰科多年生寄生植物,用于治疗头错、眩晕、肢体麻木等症,冯孝章和周俊等分离并鉴定出天麻的活性成分有天麻甙（对羟甲基苯β－D－吡喃葡萄糖式,亦称天麻素）、天麻甙元（对羟基苯甲醇）等,其中天麻甙为主要成分,一些药理实验也证实了这一点,在测定天麻甙含量的方法中,采用高效液相色谱法9HPLC）最多,正相PHLC和反相HPLC都可用于天麻及其占天麻甙的分离,-通常采用紫外检测法,检测波长在220nm或270nm处。     

苯甲酸钐的水热合成和热分解反应机理

用水热法合成了无水苯甲酸钐配合物,经元素分析、IR和X射线粉末衍射表征了该配合物,系层状结构,属单斜晶系。用TG、DTA、IR、色谱-质谱联用仪研究了它的热分解机理。在氮气氛下,热分解分两步进行:第一步分解生成钐的二碳酸一氧盐和有机化合物。生成的有机化合物成分比较复杂,主要成分为苯甲酸、二苯甲酮、9,10-蒽醌和1,3-二苯基异苯并呋喃等。第二步二碳酸一氧盐进一步分解生成氧化钐和二氧化碳。     

高效液相色谱法同时测定血清和尿中厚朴酚与和厚朴酚

 建立了大鼠服用厚朴提取物后的血清中及尿中厚朴酚与和厚朴酚的高效液相色谱测定法。色谱柱填料为SpherisorbC18,流动相为甲醇-水-冰醋酸(体积比为70∶30∶1),UV检测波长为294nm,灵敏度0.005AUFS。样品用甲醇沉淀蛋白,上清液酸化后用乙酸乙酯-乙醚萃取,然后测定其中的药物浓度。血清和尿中的药物浓度与峰面积的线性关系良好,线性范围分别为0.05～2mg/L(厚朴酚)、0.025～1mg/L(和厚朴酚);精密度和重现性良好。血清中厚朴酚与和厚朴酚的平均加样回收率分别为95.6%(RSD=3.85%)和93.8%(RSD=3.95%),尿中分别为96.0%(RSD=3.83%)和94.9%(RSD=3.54%)。     

Structurally designed synthesis of mechanically stable poly(benzoxazine-co-resol)-based porous carbon monoliths and their application as high-performance CO2 capture sorbents

Porous carbon monoliths with defined multilength scale pore structures, a nitrogen-containing framework, and high mechanical strength were synthesized through a self-assembly of poly(benzoxazine-co-resol) and a carbonization process. Importantly, this synthesis can be easily scaled up to prepare carbon monoliths with identical pore structures. By controlling the reaction conditions, porous carbon monoliths exhibit fully interconnected macroporosity and mesoporosity with cubic Im3m symmetry and can withstand a press pressure of up to 15.6 MPa. The use of amines in the synthesis results in a nitrogen-containing framework of the carbon monolith, as evidenced by the cross-polarization magic-angle-spinning NMR characterization. With such designed structures, the carbon monoliths show outstanding CO(2) capture and separation capacities, high selectivity, and facile regeneration at room temperature. At ~1 bar, the equilibrium capacities of the monoliths are in the range of 3.3-4.9 mmol g(-1) at 0 °C and of 2.6-3.3 mmol g(-1) at 25 °C, while the dynamic capacities are in the range of 2.7-4.1 wt % at 25 °C using 14% (v/v) CO(2) in N(2). The carbon monoliths exhibit high selectivity for the capture of CO(2) over N(2) from a CO(2)/N(2) mixture, with a separation factor ranging from 13 to 28. Meanwhile, they undergo a facile CO(2) release in an argon stream at 25 °C, indicating a good regeneration capacity.     

固相萃取-气质联用法测定纺织品中的磷酸三酯类阻燃剂

建立了固相萃取-气质联用法同时测定纺织品中的烷基磷酸三酯和芳香基磷酸三酯类阻燃剂的方法.采用乙腈-甲苯(3∶1,Ⅴ/Ⅴ)混合溶液作为提取剂,对纺织品中的磷酸三酯类阻燃剂进行提取;再用ENVI-Carb固相萃取柱对提取液中的目标分析物进行净化处理;氮吹浓缩定容后,用气质联用仪进行定性与定量分析.磷酸三(2,3-二溴丙基)酯在0.050～20 mg/L浓度范围内存在良好的线性关系,相关系数r为0.9859;定量限为0.050 mg/kg (S/N=10).其它目标分析物在0.010～20 mg/L浓度范围内存在良好的线性关系,r为0.9998～1.000;定量限为0.010 mg/kg(S/N=10).本方法成功应用于纺织品中磷酸三酯类阻燃剂的检测,加标回收率在71.4％～102.5％之间;RSD≤4.9(n=6).分析的20个样品中,有一个Ⅰ类样品检出TBP,含量为(62.2±0.3) μg/kg.     

固相萃取-气相色谱法测定茶叶中甲胺磷残留量

茶叶样品经乙酸乙酯提取,上清液于50℃蒸发至近干,加入乙酸乙酯溶解残渣后,经硅胶-石墨化碳混合柱净化。先以乙酸乙酯洗脱去除杂质,再以碱化乙腈洗脱并收集流出液,在50℃蒸发至近干,加乙酸乙酯定容至1mL,供气相色谱分析。采用DB-1701色谱柱分离和火焰光度检测器检测,所得甲胺磷的线性范围为0.010～1.00mg·L-1,方法的检出限(3S/N)为0.005mg·kg-1。在0.010,0.020,0.080 mg·kg-1 3个浓度水平下进行回收试验,甲胺磷的回收率在85.0%～90.9%之间,相对标准偏差(n=6)在2.2%～4.3%之间。     

Carbon nanotube enhanced membrane distillation for online preconcentration of trace pharmaceuticals in polar solvents

Carbon nanotube enhanced membrane distillation (MD) is presented as a novel, online analytical preconcentration method for removing polar solvents thereby concentrating the analytes, making this technique an alternate to conventional thermal evaporation. In a carbon nanotube immobilized membrane (CNIM), the CNTs serve as sorbent sites and provide additional pathways for enhanced solvent vapor transport, thus enhancing preconcentration. Enrichment using CNIM doubled compared to membranes without CNTs, while the methanol flux and mass transfer coefficients increased by 61% and 519% respectively. The carbon nanotube enhanced MD process showed excellent precision (RSD of 3-5%), linearity, and the detection limits were in the range of 0.001 to 0.009 mg L(-1) by HPLC analysis.     

超声萃取-高效液相色谱法测定沉积物中多环芳烃

提出了高效液相色谱法测定沉积物中多环芳烃(PAH′s)含量的方法。样品中多环芳烃用正己烷-丙酮(1+1)混合溶液超声提取,离心分离后,所得萃取液经蒸发浓缩,然后过装有1g无水硫酸钠和2g硅胶的层析柱净化。以Varian PAHs色谱柱为分离柱,不同比例配成的甲醇和水为流动相梯度洗脱,用荧光检测器检测。方法的检出限(3S/N)在0.34～1.52ng.g-1之间。方法用于沉积物中多环芳烃的测定,测定结果的相对标准偏差(n=5)在3.2%～10.6%之间。用标准加入法测定方法的回收率,结果在57.1%～103.4%之间     

气相色谱-质谱法测定食品中邻苯二甲酸酯

提出了气相色谱-质谱法测定食品中16种邻苯二甲酸酯(PAE′s)含量的方法。详细叙述了不同基质的食品的处理方法,高脂类样品需经凝胶渗透色谱净化。采用HP-5MS石英毛细管柱进行分离和电子轰击离子源质谱检测。16种PAE′s的线性范围为0.50～20.0mg·L-1,检出限(3S/N)在6.03～826μg·kg-1之间。在1,10mg·kg-1两个浓度水平进行加标回收试验,纯油脂和高脂固体样品中16种PAE′s的平均回收率分别在79.2%～101%和77.8%～97.4%之间,测定值的相对标准偏差(n=6)分别在3.4%～6.9%和4.1%～6.0%之间。     

多壁纳米碳管/二氧化硅复合膜中的联吡啶钌电化学发光法测定氧氟沙星的研究与应用

基于氧氟沙星对联吡啶钌(Ru(bpy)_3~(2+))电化学发光的增敏作用,建立了一种以多壁纳米碳管(MWCNTs)/二氧化硅-联吡啶钌复合物修饰的玻碳电极电化学发光检测氧氟沙星的新方法.利用溶胶-凝胶(sol-gel)固定化稳定的优点和纳米碳管的电催化作用,提高了传感器的电流响应.在最佳实验条件下,氧氟沙星浓度在4.0×10~(-6) ～1.0×10~(-4) mol/L范围内与相对发光强度呈线性关系(r~2=0.994 8),检出限(S/N=3)为2.0×10~(-6) mol/L.连续平行测定2.4×10~(-5) mol/L的氧氟沙星溶液 5次,发光强度的RSD为1.8%.