微量乳酸脱氢酶毛细管电泳在线反应电化学检测方法的研究

以乳酸脱氢酶催化乳酸与NAD⁺反应生成丙酮酸与NADH和安培法检测NADH为基础,利用电泳中介微分析(EMMA)技术,研究了超微量乳酸脱氢酶的毛细管电泳在线反应的电化学检测方法,并从理论上对EMMA电泳图中的平台宽度和高度作了初步探讨.结果表明,在EMMA的恒高压和零高压两种模式下,使用直径为150μm和束状碳纤维电极,在+0.8V检测电位下,对LDH活性检测灵敏度分别为1.1nU和0.6nU;所导出的平台高度、宽度与实验条件的关系式对提高毛细管电泳分离效率和检测灵敏度有一定指导意义.     

Immobilization of lactate as an electroactive indicator on pencil graphite electrode for the development of a new electrochemical biosensor for the detection of lactate dehydrogenase

A biosensor was developed for the detection of lactate dehydrogenase (LDH) enzyme using a lactate modified pencil graphite electrode (PGE). The sensor relies on the immobilization of the lactate on PGE, and LDH detection is based on the decrease of lactate peak current following oxidation to pyruvate in the presence of LDH. Square wave voltammetric technique was used for the assay of signals in the range of ?0.6 to 0.8 V and a frequency of 25 Hz for the determination of LDH. The dependence of the response was investigated in terms of reaction time, washing time and LDH and NAD⁺ amounts. Also, the electrochemical behavior of LDH treatment on the lactate modified PGE was studied. The electrode showed good selectivity, repeatability and an operational stability of about 90% of its original response for two weeks. Moreover, the sensor displayed a linear response range from 0.36?C2.13 U ??l^?1 for LDH with a detection limit of 0.16 U ??l^?1. The response time of the LDH-treated lactate modified PGE was found to be 2 s. The relative standard deviation (RSD) obtained was 3.5% (for LDH 0.71 U ??l^?1 and n = 3).     

Amperometric determination of serum lactate dehydrogenase activity using an ADP-modified graphite electrode

Graphite electrodes modified with a drop-coated layer of polyethyleneimine (PEI) and adenosine diphosphate (ADP) displayed an electrocatalytic response to NADH after the adenine moiety of ADP was electrochemically oxidised. NADH can be detected amperometrically in alkaline solution (pH 9.0) at low applied potentials (+50 mV (Ag/AgCl)). Using a stationary electrode arrangement, linear response for NADH concentrations between 1.0×10⁻⁸ and 1.0×10⁻⁴ M was found, with a response time of 12 s and a detection limit of 8×10⁻⁹ M. The electrode was applied to the amperometric monitoring of the reaction between lactate and NAD⁺ catalysed by lactate dehydrogenase (LDH). A flow injection-amperometric method for the determination of LDH activity in human serum was developed. The method allows a fast and accurate discrimination between pathological and normal LDH activity levels, with a sampling rate of 40 h⁻¹. Quantitative results for a random set of human serum samples were found to be in good agreement with the standard spectrophotometric method.     

Voltammetric copper(II) determination with a montmorillonite-modified carbon paste electrode

The clay mineral montmorillonite has been tested as modifier for the carbon paste electrode with a novel electrode modification technique. The differential pulse voltammetric determination of copper(II) by means of this modified carbon paste electrode has been studied. A detection limit of 4x10(-8) mol/l has been achieved after 10 min preconcentration under open circuit conditions with subsequent anodic stripping voltammetry. The calibration curve for Cu(II) is linear in the range of 4x10(-8)-8x10(-7) mol/l. Pb interferes in a 10-fold molar and Cd and Hg in a 100-fold molar excess. The interference by humic ligands is significant.     

l- and d-Lactate assay in real milk samples with immobilized enzyme reactors and graphite electrode

A sensitive flow system for the determination of l- and d-lactate in milk samples is described. l- and d-Lactate dehydrogenase, LDH, were immobilized on aminopropyl-controlled pore glass beads. l- and d-Lactate are oxidized to pyruvate in the presence of NAD(+) and NADH is produced. The electrochemical determination of NADH allows the measurement of the substrate involved in the reaction. We used a graphite-based anode sensor without any mediator at +500 mV vs. Ag/AgCl. The analytes were measured, in standard solutions, in the concentration range from 1 x 10(-6) to 4 x 10(-4)M using 1 mM NAD(+) concentration and 0.1M Tris buffer pH 9. Experiments with real milk samples showed large values of currents probably due to electroactive substances usually contained in milk. To eliminate interfering compounds a microdialysis probe coupled with a pre-oxidizing cell was used. This method of pre-treatment removes the interfering substances, but leaves the analytes under study unaffected. The procedure allows the determination of l- and d-lactate in milk samples in the concentration range from 1 x 10(-5) to 5 x 10(-4)M. The assay was applied to monitor continuously the bacterial fermentation of Staphylococcus aureus in UHT milk as an example of possible contamination detection in the manufacturing process.     

Study of carbon nanotubes-HRP modified electrode and its application for novel on-line biosensors

In this paper, multi-walled carbon nanotubes (MWCNTs) were successfully immobilized on the surface of a glassy carbon electrode by mixing with horse-radish peroxidase (HRP). The electrochemical behavior of H2O2 was also studied with the MWCNTs-HRP modified electrode as a working electrode. The MWCNTs-HRP modified electrode showed excellent response of reduction current for the determination of H2O2 at the potential of -300 mV (vs. Ag/AgCl). We assembled the MWCNTs-HRP modified electrode in a thin-layer flow cell and the H2O2 solution was continuously introduced into the cell with a syringe pump. We optimized the sensitivity of the H2O2 sensor by adjusting the working potential and the pH of the buffer solution. The peak current increased linearly with the concentration of H2O2 in the range 3.0 x 10(-7) to approximately 2.0 x 10(-4) mol L(-1). The detection limit is 1.0 x 10(-7) mol L(-1) (S/N = 3). The interferences from ascorbic acid, uric acid and other electroactive substances can be greatly excluded since the sensor can be operated at -300 mV. Stability and reproducibility of the MWCNTs-HRP chemically modified electrode were also studied in this paper. Fabricated with glucose and lactate oxidase, the MWCNTs-HRP electrode was also applied to prepare the on-line glucose and lactate biosensors because of the high sensitivity for the determination of H2O2.     

Amperometric biosensor for ethanol based on immobilization of alcohol dehydrogenase on a nickel hexacyanoferrate modified microband gold electrode

Alcohol dehydrogenase (ADH) has been immobilized on a nickel hexacyanoferrate modified microband gold electrode surface by a glutaraldehyde/bovine serum albumin (BSA) cross-linking procedure to provide a new amperometric sensor for the assay of ethanol. The resulting enzyme electrode exhibits excellent electrocatalysis for the oxidation of reduced nicotinamide-adenine dinucleotide (NADH). The amperometric determination is based on the electrochemical detection of NADH which is generated in the enzymatic reaction of ethanol with NAD(+) under catalysis of ADH. The influence of various experimental conditions was examined for the determination of the optimum analytical performance. The sensor responds rapidly to ethanol with a detection limit of (5.0 +/- 0.3) x 10(-7) mol 1(-1). The response current increases linearly with ethanol concentration up to 5 mmol 1(-1). The sensor remains relatively stable for about 1 week.     

Flow injection determination of bromide ion in a developer using bromide ion-selective electrode detector

A potentiometric flow injection determination method for bromide ion in a developer was proposed, by utilizing a flow-through type bromide ion-selective electrode detector. The sensing membrane of the electrode was Ag(2)S-AgBr membrane. The response of the electrode detector as a peak-shape signal was obtained for injected bromide ion in a developer. A linear relationship was found to exist between peak height and the concentration of the bromide ion in a developer in a concentration range from 1.0x10(-3) to 1.0x10(-2) mol l(-1). The relative standard deviation for 10 injections of a 6x10(-3) mol l(-1) bromide ion in a developer was 1.3% and the sampling rate was ca 17-20 samples h(-1). The present method was free from the interference of an organic reducing reagent, an organic substance in a developer sample solution for the determination of bromide ion in a developer.     

Determination of lactate or oxalate using injected lactate oxidase and peroxidase by capillary electrophoresis with UV detection

Two reactions, catalyzed by lactate oxidase (LO) and peroxidase, are initiated by a single injection of the enzymes and the substrate 2,2'-azino-bis(3-ethylene-thiazoline-6-sulfonic acid) (ABTS) into the capillary previously filled with the sample (lactate or lactate-oxalate mixture) and the run buffer containing NADH. The oxidized ABTS product upon reaction with NADH is converted to NAD(+) which is separated and detected in less than 2 min at 266 nm with a sample throughput of 7 min (including wash steps between samples). Simplex trade mark software is used to optimize the enzyme concentrations and reaction temperature. Consumption of the more expensive LO enzyme is only 1.4 x 10(-3) U per assay assuming 27 nL per injection. Linearity is established within the range from 0.0025 to 1 mM with R(2) of 0.9982. Recoveries of lactate from five spiked serum samples averaged 101%. Application of this method for the determination of oxalate as an inhibitor of LO is demonstrated.     

Bioluminescent flow sensor for the determination of L-(+)-lactate

The amount of L-lactate in biological fluids (serum, plasma and cerebrospinal fluid) was determined by monitoring the reduced form of nicotinamide adenine dinucleotide (NADH) produced by immobilised lactate dehydrogenase (LDH), with bacterial bioluminescent enzymes immobilised on a separate nylon coil. The LDH catalysed the reaction of L-lactate with NAD; this reaction took place in a nylon coil that preceded the coil for the bioluminescent detection. The co-immobilisation of alanine aminotransferase (ALT) with LDH improved the lactate transformation by 117-183%. The response was linear from 0.1 to 50 micron mol l(-1) at 25 degrees C for the LDH - ALT reactor. The intra- and inter-assay coefficients of variation were less than 5% and the recoveries ranged from 93 to 106%. The results agreed well with those obtained with a spectrophotometric method and with the normal reference values.     

Differential pulse anodic stripping voltammetric determination of traces of copper with a tobramycin-Nafion modified electrode.

A Nafion-modified glassy carbon electrode incorporated with tobramycin for the voltammetric stripping determination of Cu2+ has been explored. The electrode was fabricated by tobramycin containing Nafion on the glassy carbon electrode surface. The modified electrode exhibited a significantly increased sensitivity and selectivity for Cu2+ compared with a bare glassy carbon electrode and the Nafion modified electrode. Cu2+ was accumulated in HAc-NaAc buffer (pH 4.6) at a potential of -0.6 V (vs. SCE) for 300 s and then determined by differential pulse anodic stripping voltammetry. The effects of various parameters, such as the mass of Nafion, the concentration of tobramycin, the pH of the medium, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 1.0 x 10(-9) to 5.0 x 10(-7) mol l(-1) with a correlation coefficient of 0.9971. The relative standard deviations for eight successive determinations were 4.3 and 2.9% for 1.0 x 10(-8) and 2.0 x 10(-7) mol l(-1) Cu2+, respectively. The detection limit (three times signal to noise) was 5.0 x 10(-10) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determination of copper in water samples, and also in analytical reagent-grade salts with satisfactory results.     

Cathodic adsorptive stripping voltammetric determination of uranium with potassium hydrogen phthalate

The adsorption properties of dioxouranium (II)-Phathalate complexes onto hanging mercury drop electrode are exploited in developing a highly sensitive and selective stripping voltammetric procedure for the determination of uranium (VI). The reduction current of adsorbed complex ions of U(VI) was measured by both linear sweep (LSCSV) and differential pulse cathodic stripping voltammetry (DPCSV), preceded by a period of preconcentration onto the electrode surface. As low as 2x10(-9) mol dm(-3) (0.5 mug/l) and 2x10(-8) mol dm(-3) (4.8 mug/l) with accumulation time 240 and 120 s using DPCSV and LSCSV, respectively, have been determined successfully. The relative standard deviation of 2.2% at the 5 ppm level was obtained. The interferences of some metal ions and anions were studied. The application of this method was tested in the determination of uranium in superphosphate fertilizer.     

Amperometric Biosensor for Lactate Based on Meldola's Blue Adsorbed on Silica Gel Modified with Niobium Oxide

A reagentless amperometric biosensor sensitive to lactate was developed. This sensor comprises a carbon paste electrode modified with lactate dehydrogenase (LDH), nicotinamide adenine dinucleotide (NAD⁺) cofactor and Meldola's blue (MB) adsorbed on silica gel coated with niobium oxide. The amperometric response was based on the electrocatalytic properties of MB to oxidize NADH, which was generated in the enzymatic reaction of lactate with NAD⁺ under catalysis of LDH. The dependence on the biosensor response was investigated in terms of pH, supporting electrolyte, ionic strength, LDH and NAD⁺ amounts and applied potential. The biosensor showed an excellent operational stability (95% of the activity was maintained after 250 determinations) and storage stability (allowing measurements for over than 2.5 months, when stored in a refrigerator). The proposed biosensor also presented good sensitivity allowing lactate quantification at levels down to 6.5×10^?6 mol L^?1. Moreover, the biosensor showed a wide linear response range (from 0.1 to 14 mmol L^?1 for lactate). These favorable characteristics allowed its application for direct measurements of lactate in biological samples such as blood. The precision of the data obtained by the proposed biosensor show reliable results for real complex matrices.     

Spectrofluorimetric determination of both hydrogen peroxide and -O-O-H in polyethylene glycols (PEGs) using 2-hydroxy-1-naphthaldehyde thiosemicarbazon (HNT) as the substrate for horseradish peroxidase (HRP)

2-Hydroxy-1-naphthaldehyde thiosemicarbazon (HNT) had been synthesized and used as a new kind of substrate for horseradish peroxidase (HRP) in spectrofluorimetric determination of hydrogen peroxide (H(2)O(2)). The oxidation reaction of HNT with H(2)O(2) under the catalysis of HRP was studied in detail. The possible reaction mechanism was discussed. Under optimum experimental conditions, the oxidized product of HNT had excitation and emission maxima at 260 and 450 nm, respectively. The linear range of this method was 1.30 x 10(-9)-1.25 x 10(-5) mol l(-1) with a detection limit of 3.89 x 10(-10) mol l(-1). The effect of interferences, surfactants and organic solvents on the determination of H(2)O(2) had been investigated. A study to prove the existence of -O-O-H in PEGs was carried out. The proposed method was successfully applied to the determination of -O-O-H in polyethylene glycols.     

Flow injection amperometric detection of ascorbic acid using a Prussian Blue film-modified electrode

The PB film-modified electrode was used as an amperometric detector for flow injection analysis of ascorbic acid. The modified electrode detector showed good sensitivity, stability and reproducibility. The calibration curve for ascorbic acid was linear over the concentration range from 5.0x10(-6) to 1.0x10(-3) mol l(-1) with a slope of 19.9 mA mol(-1) per litre and a correlation coefficient of 0.999. The detection limit of this method was 2.49x10(-6) mol l(-1). The relative standard deviation of six replicate injections of 2.5x10(-4) mol l(-1) ascorbic acid was 2.5%. The results obtained for ascorbic acid determination in pharmaceutical products are in good agreement with those obtained by using the procedure involving the reaction between triiodide and ascorbic acid.     

Determination of trace procaine hydrochloride by differential pulse adsorptive stripping voltammetry with a Nafion modified glassy carbon electrode.

A sensitive and selective method for the determination of procaine hydrochloride with a Nafion-modified glassy carbon electrode has been developed. The voltammetric behavior of procaine hydrochloride on the Nafion-modified electrode indicated that the modified electrode not only increased the sensitivity of the determination of procaine hydrochloride, but also catalyzed the electrode process. Procaine hydrochloride was accumulated in Britton-Robinson buffer (pH 2.09) at a potential of -0.2 V (vs. SCE) for 180 s, and was then determined by differential pulse adsorptive stripping voltammetry. The effect of various parameters, such as the pH of the medium, the mass of drop-coated Nafion, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 6.0 x 10(-8) to 6.0 x 10(-6) mol l(-1) with a correlation coefficient of 0.9987. The relative standard deviation was 4.18% for eight successive determinations of 1.0 x 10(-7) mol l(-1) procaine hydrochloride, and the detection limit (three times signal to noise) was 7.0 x 10(-9) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determinations of procaine hydrochloride in the injection solution of procaine hydrochloride and in rabbit serum.     

A novel voltammetric method for the direct determination of copper in complex environmental samples.

A novel voltammetry with a modified gold electrode for the direct determination of copper in environmental samples, without any pretreatment, is proposed in this paper. A porous disorganized monolayer was formed on the surface of the gold electrode by the self-assembly of mercaptoacetic acid (MAA), which could selectively permeate small molecules. Subtractive square wave anodic stripping voltammetry (SASV) was applied to determine copper, in which the underpotential deposition (UPD) of copper was used as the deposition step. The linear range was from 8 x 10(-7) to 1 x l0(-5) mol l(-1) by the modified electrode in the presence of human serum albumin, and the determination was not interfered with common metal ions. Copper in a real environmental sample was successfully detected.     

Electrochemical behavior of epinephrine at l-cysteine self-assembled monolayers modified gold electrode

The electrochemical behaviors of epinephrine (EP) at the l-cysteine self-assembled monolayers modified gold electrode have been studied. The modified electrode shows an excellent electrocatalytic activity for the oxidation of EP and accelerates electron transfer rate. The diffusion coefficient (D) is 1.48x10(-7) cm(2) s(-1). FTIR has shown that cysteine can bind onto the gold surface through the strong sulfur-gold interaction. The electrocatalytic mechanism to EP has been studied. The catalytic current of EP nu s its concentration has a good linear relation in the range of 1.0x10(-7)-2.0x10(-6) mol l(-1), with the correlation coefficient of 0.9989 by differential pulse voltametric (DPV) response. Detection limit is down to 1.0x10(-8) mol l(-1). At a high EP concentration, the relationship between the catalytic current and its concentration exhibits a Michaelis-Menten kinetic mechanism for the electrocatalytic process and the constant K(m) is about 0.155 mmol l(-1). The highest catalytic current I(m) is 2.72 muA. The modified electrode can be used for the determination of EP in practical injection. The method is simple, quick, sensitive and accurate.     

Potentiometric flow injection determination of amylase activity by using hexacyanoferrate(III)-hexacyanoferrate(II) potential buffer

A highly sensitive potentiometric flow injection determination of amylase activity was carried out, utilizing a redox reaction of hexacyanoferrate(III) in alkaline media with reducing sugar as product of the enzymatic hydrolysis reaction of starch with amylase. The analytical method is based on the potential change detection of a flow-through type redox electrode detector due to the composition change of a [Fe(CN)(6)](3-)-[Fe(CN)(6)](4-) potential buffer solution, which is caused by the redox reaction with the product of the enzymatic reaction. A linear relationship exists between the potential change (peak height) and the activity of amylase. Amylase of a wide activity range from 2.5x10(-2) to 1.2x10(-4) U ml(-1) can be determined by the changing the concentrations of the [Fe(CN)(6)](3-)-[Fe(CN)(6)](4-) potential buffer from 10(-3) to 10(-5) M. The lower detection limit of amylase activity is 6.0x10(-5) U ml(-1). The sampling rate and relative standard deviation are 15 h(-1) and 0.9% (n=5) for 3.8x10(-3) U ml(-1) of amylase. The present method was successfully applied to determine amylase activity in real samples (commercial digestive medicines) with an accuracy of 4% compared with analytical results obtained using the present method with those achieved using the conventional titration method.     

Adsorption voltammetry of the scandium-alizarin red S complex onto a carbon paste electrode

For the first time, a new method is described for the determination of scandium based on the cathodic adsorptive stripping of the scandium-alizarin red S complex onto a carbon paste electrode. The second-order derivative linear scan voltammograms of the complex are recorded by use of model JP-303 polarographic analyzer from 0.0 to -1.0 V (versus SCE). Optimum conditions are found to be: an acetic acid (0.36 mol l(-1))-potassium biphthalate (0.064 mol l(-1)) buffer solution (pH 4.0) containing 2.0x10(-5) mol l(-1) alizarin red S, a preconcentration potential of 0.0 V, a preconcentration time of 60 s, a rest time of 10 s and a scan rate of 100 mV s(-1). The results show that the complex can be adsorbed on the surface of a carbon paste electrode, yielding one peak at -0.58 V, corresponding to the reduction of alizarin red S in the complex at the electrode. The detection limit is found to be 6.0x10(-10) mol l(-1) for 3 min of preconcentration time. The linear range is 1.0x10(-9) to 4.0x10(-7) mol l(-1). Application of the procedure to the determination of scandium in the ore samples gave good results.