Spectrophotometric determination of gallium in alloys and fly-ash with pyridoxal derivatives of thiocarbohydrazide and carbohydrazide

The symmetric derivatives of pyridoxal with thiocarbohydrazide and carbohydrazide, and the asymmetric derivatives of pyridoxal and salicylaldehyde with the same hydrazides have been synthesized and their analytical potential for spectrophotometric and kinetic fluorimetric determination of metal ions was studied. Gallium(III) and PyMAU(1,3-bis{[4-(2-methyl-3-hydroxy-5-hydroxymethyl)pyridyl]methyleneaminourea at pH = 4.2 form a complex with a single absorption maximum at 425 nm, which can be extracted into cyclohexanone in the presence of a controlled amount of sodium perchlorate. The extract has maximum absorbance at 435 nm. Both systems can be used for determining gallium. The optimal range of gallium concentration for measurement in a 1-cm cell is 0.5-1.25 gmg/ml for the procedure in homogeneous medium ((425) = 3.76 x 10(4).mole(-1).cm(-1)) and 0.25-1.25 mug/ml for the extraction procedure ((435) = 5.30 x 10(4) 1.mole(-1).cm(-1). The latter procedure has been applied to the determination of gallium in alloys and fly-ash.     

Solvent extraction of gallium(III) as the monothiodibenzoylmethane complex

Gallium(III) can be quantitatively extracted at trace levels with monothiodibenzoylmethane in benzene at pH 5.0. It is then determined spectrophotometrically as its Rhodamine B complex in the organic phase, at 570 nm. The system conforms to Beer's law at 570 nm, in the range 1.4-26 mug of gallium. The absorbance is stable for 24 hr. Gallium can be extracted and determined in the presence of several elements with which it is generally associated in minerals and other products.     

The separation of W(V) from HCl-KSCN medium on polyurethane foam sorbents for its spectrophotometric determination in steels and silicates

A simple procedure for selective sorption of tungsten is described. The method involves reduction of W(VI) to W(V) with tin(II) chloride (2%, w/v) at 8-9M hydrochloric acid, formation of the W(V)-SCN complex with 0.2M KSCN and its sorption on polyurethane foam within 20 min. The sorbed complex is then eluted with acidified acetone (1 ml of 1M hydrochloric acid and 8 ml of acetone) followed by addition of 1 ml of 0.1M KSCN to the eluent. The method has been applied to the spectrophotometric determination of tungsten in steels and silicates by measuring the absorbance of the eluted solution at 400 nm. Beer's law is obeyed for the range 0.1-12 mug W/ml. Other elements, e.g., Co(III) (50 mug/ml), Cu(II) (10 mug/ml), Ti(IV) (20 mug/ml), V(V) (10 mug/ml) and Mo(VI) (0.5 mug/ml) have no effect on the method. Interference of copper, up to 100 mug/ml has been eliminated by masking with thiourea and that due to molybdenum by prior separation with thioglycollic acid on PUF. The method has been verified with standard samples.     

Application of partial least-squares regression to the resolution of highly correlated spectra. Simultaneous spectrofluorimetric determination of Al(3+), Ga(3+) and In(3+)

The simultaneous spectrofluorimetric determination of mixtures of aluminium, gallium and indium as their 8-hydroxyquinoline complexes following extraction into chloroform is studied. The high collinearity of the spectra hindered their resolution by multiple linear regression (MLR) methodology; therefore, experimental data were processed by partial least-squares regression (PLSR) methodology. A previous step in the study of three-dimensional fluorescence spectrum is possible to select the best information to quantify this system with high collinearity. Finally the optimal conditions for quantitation, the best data preprocessing procedure and the most suitable spectral mode for calibration were established. Using an external set allowed the three analytes to be determined simultaineously at concentrations below 1 mug ml(-1) with errors less than 10% for aluminium and indium, and 15% for gallium.     

Solvent extraction of gallium(III) with 2-thenoyltrifluoroacetone

Gallium can be quantitatively extracted at trace levels with 2-thenoyltrifluoroacetone in xylene at pH 4.5-6.0. Gallium is determined in the organic phase photometrically by complexation with Rhodamine B. The system conforms to Beer's law (at 565 nm) in the concentration range 2-59 mug ml . The complex is stable for 24 hr. Salting-out agents have no effect on the extraction. Gallium can be extracted and determined in a single extraction in presence of many elements associated with it, such as indium, thallium and aluminium.     

Spectrophotometric determination of phenol and resorcinol by reaction with p-aminophenol

Based on the reaction with p-aminophenol, a series of procedures have been developed for the spectrophotometric determination of phenol and resorcinol. Three basic approaches have been studied: (i) a batch procedure, using the dissolved oxygen as oxidant, (ii) a stopped-flow procedure by use of KIO(4) as oxidant and (iii) a flow injection (FI) procedure developed in the presence of KIO(4). Phenol can be accurately determined at 626 nm, in the stopped-flow mode, after a reaction time of 45 min in 0.005M NaOH, 0.004M KIO(4) and 500 mug/ml of PAP. The development of a manifold, which incorporates a sample parking, is a convenient approach which makes it possible to measure, in the stopped-flow mode, four solutions in one hour. The limit of detection of this method corresponds to 64 ng/ml of phenol Resorcinol can be determined by FI at 540 nm in 0.006M NaOH, 0.0002M KIO(4) and 50 mug/ml PAP with a limit of detection of 6.6 ng/ml and a sample throughput of 300 injections per hour. A combination between the FI procedure for the determination of resorcinol and the stopped-flow procedure for phenol determination provides accurate results in the analysis of spiked samples containing both phenol and resorcinol.     

Selective edta titration of gallium or aluminium in the presence of other metals

The selective determination of aluminium or gallium by EDTA titration is reported. Gallium or aluminium is titrated together with other multivalent ions with EDTA at pH 3-7 and then the pH is raised above 10.5. Aluminates or galliumates are formed with the consequent release of EDTA from the EDTA complexes. The released EDTA is titrated with lead solution using Xylenol Orange as an indicator and with copper using photometric detection of the end-point, for the determination of gallium and aluminium respectively. The theoretical basis of the procedure is discussed.     

Determination of arsenic by polyurethane foam extraction and X-ray fluorescence

A method based on extraction with polyurethane foam and determination by X-ray fluorescence has been developed for the determination of arsenic. Arsenic concentrations as low as 36 mug ml can be detected in 100 ml of aqueous solution.     

Separation gallium-fer en presence d'edta

Macro- or microquantities of gallium can be separated from iron by precipitating the latter with sodium hydroxide in the presence of EDTA. Nearly all the gallium remains in solution. After the separation of iron, gallium is extracted with tributylphosphate from 3 N hydrochloric acid medium, and then re-extracted into water. Gallium is finally determined by precipitation with cupferron and ignition to the oxide, or for trace amounts of gallium, by colorimetric determination with rhodamine B. The method was checked with radioactive gallium and iron.     

Spectrophotometric extractive titrations-II Determination in gallium arsenide of the sum of metals extractable with dithizone

A procedure for the determination of the sum of metals, which are extractable with dithizone, in gallium arsenide is given. After the dissolution of the sample the impurities are extracted with several portions of 10(-4)M dithizone in carbon tetrachloride, gallium being screened by tartrate ion. The excess of the reagent is extracted into 0.1M aqueous ammonia and after stripping into carbon tetrachloride the dithizone is determined by spectrophotometric extractive titration. The effect of pH is considered. The limit of detection, based on the evaluation of twenty blanks, is 2.30 x 10(-8) mole, the equivalent of 1.50 mug of zinc.     

Katalytische bestimmung von silberspuren in wabetariger lösung und nach extraktion

The application of the catalysed oxidation of Bromopyrogallol Red by potassium per- sulphate for silver determination is discussed. In aqueous solution silver concentrations of 0.5- 1 mug/ml can be determined and 1- 13 ng/ml in the presence of 1, 10-phenanthroline as activator. In combination with solvent extraction, catalytic determination of the extracted silver is possible even in presence of 200 mug of iron(III), cobalt(II) and palladium(II). By means of an automatic variant of the simultaneous comparison method a more sensitive determination (0.2-20 ng/ml) was achieved.     

The polarographic behaviour of ketoprofen and assay of its capsules using spectrophotometric and voltammetric methods

The quantitative determination of ketoprofen using spectrophotometric and voltammetric methods are described. The spectrophotometric procedure depends upon the reaction of ketoprofen with N-bromosuccinimide (NBS). The residual reagent is then determined by formation of violet colour with 2,2-diphenyl-l-picryl hydrazine (DPPH(2)). The consumed NBS would correspond to ketoprofen. Beer's law is valid over the concentration range 5-80 mug/ml of the drug. Direct current (DC) polarography allows to study the reduction behaviour of ketoprofen at the dropping mercury electrode (DME) using different supporting electrolytes at different pH values. Direct current stripping voltammetry (DCSV) was used for the quantitative measurements of the drug. The calibration graph of peak current vs concentration was linear from 0.254 x 10(-2) to 0.254 mug/ml. In model solutions as little as 5.08 x 10(-4) ng/ml ketoprofen can be detected by DCSV. Both methods were applied successfully for the determination of ketoprofen either in pure or dosage forms.     

The determination of lead in mosses by means of its catalytic effect on the persulphate oxidation of Pyrogallol Red

Lead is determined in aqueous solution in the concentration range 0.002-10 mug/ml by its catalytic effect on the oxidation of Pyrogallol Red at pH 8.5. The method has been applied to the determination of lead in mosses by means of a wet ashing procedure using nitric and perchloric acids and separation from interfering ions by extraction as the dithizone complex into chloroform, and back-extraction.     

Application of photochemical inhibition in flow injection systems: Determination of epinephrine and L-dopa

An automated procedure for the photochemical determination of epinephrine and L-dopa has been developed. It is based on the strong inhibition by these catecholamines on the photochemical reaction between phloxin and ethylenediaminetetraacetic. The proposed flow-injection method allows the fluorimetric determination of epinephrine in the range 1.9-26.4 mug/ml and of L-dopa in the range of 1.5-12.7 mug/ml, with a sampling frequency of 35 samples/hr. The method was applied successfully to the determination of body catecholamines in pharmaceutical preparations.     

Molybdenum determination in iron matrices by ICP-AES after separation and preconcentration using polyurethane foam

A procedure is proposed for the separation and determination of molybdenum in iron matrices by a batch process. It is based on the solid-phase extraction of the molybdenum(V) ion as thiocyanate complex on polyurethane (PU) foam. The extraction parameters were optimized. Using 0.20 mol L-1 hydrochloric acid, a thiocyanate concentration of 0.10 mol L-1, 100 mg of polyurethane foam and shaking time of 10 min, molybdenum (5-400 micrograms) can be separated and preconcentrated from large amounts of iron (10 mg). Desorption was carried out instantaneously by conc. nitric acid or acetone. Distribution coefficients, sorption capacity of the PU foam and coefficients of variation were also evaluated. The effect of some ions on the separation procedure was assessed. Iron(III) should be reduced to iron(II). The proposed procedure was used to determine molybdenum in standard iron matrices such as steel and pure iron. The achieved results did not show significant differences with certified values.     

Solvent extraction separation of gallium with 18crown6 from chloride media

Gallium was quantitatively extracted with 0.02M 18crown6 in methylene chloride from 6M hydrochloric acid, then stripped with 1M acetic acid and determined with 2-(pyridylazo)naphthol with measurement at 545 nm. Gallium was separated from indium, thallium, lead, aluminium and bismuth. The method was applied to determination of gallium in bauxite.     

Micelle-stabilized liquid room-temperature phosphorimetry for metals: The micellar reaction of gallium with 7-iodo-hydroxyquinoline-5-sulfonic acid and its application to the metal determination

The Ga(III)-7-iodo-8-hydroxyquinoline-5-sulfonic acid complex in the presence of suitable micelles and with sodium sulfite as oxygen scavenger exhibited strong phosphorescence at room temperature in aqueous solutions. This micellar reaction provides the basis for a convenient phosphorimetric determination of traces of gallium. Different types of micelles showed their maximum enhancing effects at different pH ranges, affording greater convenience for various analytical purposes. A phosphorimetric procedure with surfactant cetyltrimethylammonium bromide as enhancing agent is proposed. The detection limit for gallium was 5 ng/ml and the calibration graph was rectilinear in the range of 5 to 600 ng/ml. The relative standard deviation was 4% at 50 ng/ml level. The applicability of this room-temperature phosphorimetric procedure to multi-component analyses for the group III elements, Al(III), Ga(III), and In(III), was demonstrated. Kalman filtering was used to deconvolute the phosphorescence spectra of mixtures of aluminium and gallium allowing the simultaneous determination of both metals with satisfactory results.     

Determination of total proteins: a study of reaction between quinones and proteins

A previous study was undertaken to test the reaction of several quinones (p-benzoquinone; 2,5-dichloro and 2,6-dichloro p-benzoquinone; tetrachloro-p-benzoquinone; tetrachloro-o-benzoquinone; 2,5-dichloro-3,6-dihydroxy-p-benzoquinone; benz[a]anthracene-7,12-dione) with bovine serum albumin (BSA). From this study, we have devised a spectrophotometric method for determination of total proteins. The quinone, tetrachloro-p-benzoquinone (p-chloranil), showed the best result. The product of reaction between proteins and p-chloranil absorbed at 360 nm and Beer's law was followed up to 200 mug ml(-1) of BSA. The product of reaction of BSA/p-chloranil was stable for 30 min, after that the absorbance increased 16% and kept stable for 24 h. The p-chloranil method showed a limit of detection (1.25 mug ml(-1)) lower than the biuret method (52.0 mug ml(-1)) or p-benzoquinone (PBQ) method (2.6-4.0 mug ml(-1)). The method was applied to spectrophotometric determination of total proteins in blood plasma; the results were compared with the biuret method that is widely used in clinical analysis.     

Extractive photometric determination of gallium with 8-quinolinol in layered crystals of bismuth telluride-estimation of the determination limit

A method for determining microgram amounts of gallium in milligram samples of layered monocrystals of the type A(V)(2)B(VI)(3) is described. For the separation of 1-5 mug of gallium(III) from a large excess of bismuth in a single extraction the recommended conditions are pH 3.6-4.2 (acetate buffer, V(aq) 40 ml), an adequate excess of 8-quinolinol for complete extraction and of thiosulphate for masking bismuth. The absorbance of a chloroform extract (V(org) = 10 ml) is measured at 392.5 nm in a 50-mm cell against a blank extract concurrently obtained with a solution of pure Bi(2)Te(3). Reference polycrystalline materials are used to check the precision and accuracy of the method. In routine analysis of layered monocrystals a relative standard deviation of 4-8% is to be expected for about 1 mug of gallium in the extraction system. Estimation of the limit of determination, based on two statistical models, is discussed with respect to the error of the method and the fluctuation of the blank.     

Molybdenum determination in iron matrices by ICP-AES after separation and preconcentration using polyurethane foam

A procedure is proposed for the separation and determination of molybdenum in iron matrices by a batch process. It is based on the solid-phase extraction of the molybdenum(V) ion as thiocyanate complex on polyurethane (PU) foam. The extraction parameters were optimized. Using 0.20 mol L^–1 hydrochloric acid, a thiocyanate concentration of 0.10 mol L^–1, 100 mg of polyurethane foam and shaking time of 10 min, molybdenum (5–400 μg) can be separated and preconcentrated from large amounts of iron (10 mg). Desorption was carried out instantaneously by conc. nitric acid or acetone. Distribution coefficients, sorption capacity of the PU foam and coefficients of variation were also evaluated. The effect of some ions on the separation procedure was assessed. Iron(III) should be reduced to iron(II). The proposed procedure was used to determine molybdenum in standard iron matrices such as steel and pure iron. The achieved results did not show significant differences with certified values.