Determination of ziram in vegetable samples by square wave voltammetry

The electrochemical behaviour and electrode reaction mechanism of ziram （zinc-dimethyl dithiocarbamate） on a hanging mercury drop electrode were investigated in Britton-Robinson （B-R） buffer by using cyclic and square wave voltammetry （SWV）. Based on these studies a voltammetric method for determination of ziram wasdeveloped and applied to determine the ziram in synthetic and spiked vegetable samples, satisfactory results were obtained in both cases.     

Renewable Silver‐Amalgam Film Electrode for Rapid Square‐Wave Voltammetric Determination of Thiamethoxam Insecticide in Selected Samples

The paper presents the use of a renewable silver‐amalgam film electrode (Hg(Ag)FE) for the determination of the insecticide thiamethoxam (TMO) in Britton‐Robinson buffer pH 7.0 (LOD=0.25 µg mL^?1, LOQ=0.70 µg mL^?1) by direct cathodic square‐wave voltammetry (SWV). The voltammetric response for TMO obtained at this electrode was the same as that obtained with a hanging mercury drop electrode, represented by two distinct reduction peaks. Since the electron transfer processes are coupled with chemical reactions involving protons, the SWV signals strongly depend on the pH of the supporting electrolyte. The developed Hg(Ag)FE‐SWV method was tested for the determination of TMO in spiked honey and river water samples, as well as for the determination of its content in the commercial formulation Actara 25 WG.     

Voltammetric investigation of Tamsulosin

The electrooxidative behavior and determination of Tamsulosin HCl (TAM), one of the alpha(1)-adrenoceptor antagonist, on a glassy carbon disc electrode were investigated for the first time by using cyclic, linear sweep, differential pulse (DPV) and square wave voltammetry (SWV). TAM showed an irreversible oxidation behavior at all pH values and buffers studied. From the electrochemical response, the main oxidation step was found to be related to the methoxy group on the phenyl ring. DPV and SWV were used to generate peak current versus concentration curves for TAM. A linear response was obtained in the range comprised between 2x10(-6) and 4x10(-4) M for both techniques with detection limit of 3.34x10(-7) M for DPV and 2.45x10(-7) M for SWV. The methods were proposed for the determination of TAM in dosage forms adopting both DPV and SWV modes. The methods were extended to the in vitro determination of TAM in spiked serum samples.     

The Performance of Boron‐Doped Diamond Electrode for the Determination of Ramipril and its Association with Hydrochlorothiazide

The voltammetric behavior of ramipril (RMP), an angiotensin‐converting enzyme inhibitor, was investigated for the first time in the literature on a boron‐doped diamond electrode (BDDE) using cyclic (CV) and square‐wave voltammetry (SWV). Its behavior was also considered in the presence of a thiazide diuretic, hydrochlorothiazide (HCTZ), for the simultaneous determination. The performance of BDDE and glassy carbon electrode (GCE) was compared, since RMP provides a high oxidation potential. It was observed that the anodic peak potentials for HCTZ and RMP at the BDDE were 1.23 and 1.67 V (vs . Ag/AgCl (3.0 mol L^‐1 KCl)) by CV in BR buffer solution (pH 2.0), respectively. The influence of supporting electrolyte, pH and scan rate in the current response of these both drugs was examined to select optimum experimental conditions. By this way, the determination of RMP and its association with HCTZ using SWV and a BDDE was successfully applied in real samples (single and combined dosage forms), with results in close agreement at 95% confidence level with those obtained using high‐performance liquid chromatography.     

Electrochemical Determination of Boron in Natural Waters

Abstract

A sensitive voltammetric method for the determination of trace boron, based on the formation of the complex of boric acid with 4‐hydroxy‐5‐[salicylideneamino]‐2‐7‐naphthalenedisulfonic acid (azomethine H) is described. The reduction of the boric acid‐azomethine H complex at a hanging mercury drop electrode was exploited by square wave voltammetry (SWV) and cyclic voltammetry to determine boron in natural water samples, which were collected in the regions surrounding the boron mines of Central Anatolia. A reduction peak that belongs to the boric acid‐azomethine H complex at this electrode was observed at ?1.05 V vs. Ag/AgCl/KCl_(sat.). The effects of various parameters, such as ligand concentration, boric acid concentration, and formation time of the boric acid‐azomethine H complex, were investigated. Electrochemical experiments were conducted in 1.0 M HOAc/0.5 M NH₄OAc buffer at pH of 4.4±0.2. Linear working range was established by regression analysis between 5.0×10^?8 M and 1.0×10^?4 M. The probable metal cation interferences in water samples were eliminated by adding EDTA (ethylenediaminetetraacetic acid) to the samples. Data obtained using the square wave voltammetric (SWV) technique was compared statistically with inductively coupled plasma mass spectroscopy (ICP‐MS) data. Evaluation of the method based on statistical data was performed and the values of the limit of detection (LOD) and limit of quantitation (LOQ) were found to be 4.17×10^?6 M and 1.39×10^?5 M, respectively.     

硫化物在乙酰二茂铁修饰碳糊电极上的电化学行为及电分析

研究了S2-在乙酰二茂铁(AFc)修饰碳糊电极(AFc/CPE)上的电催化氧化行为及其电化学分析方法。实验结果表明,AFc/CPE对S2-的电化学氧化具有良好的催化作用。用计时电流法(CA)测定了S2-在AFc/CPE上的电催化氧化反应速率常数k为(2.60±0.05)×105 L.mol-1.s-1。用方波伏安法(SWV)测得催化氧化峰电流与S2-的浓度在5.0×10-5～1.0×10-3 mol.L-1范围内呈良好线性关系,检出限(S/N=3)为1.3×10-7 mol.L-1,同时运用SWV法对造纸废水水样中S2-的含量进行了电化学定量测定。     

Electrocatalytic determination of L-cysteine using a modified carbon nanotube paste electrode:Application to the analysis of some real samples

The electrooxidation of L-cysteine(L-Cys) was studied using a benzoylferrocene(BF) modified multi-wall carbon nanotube paste electrode(BFCNPE) using cyclic voltammetry(CV),square wave voltammetry(SWV) and chronoamperometry(CHA).Under optimum pH in CV the oxidation of L-Cys occurs at a potential about 215 mV less positive than that at the surface of unmodified carbon paste electrode.The catalytic oxidation peak currents were dependent on the L-Cys concentration and a linear calibration curve was obtained in the range 0.7-350.0 mmol/L of L-Cys with SWV method.The detection limit(3s) was determined as 0.1 mmol/L.This method was also used for the determination of L-Cys in some real samples.     

Rapid spectrophotometric method (aqueous and extractive) for the determination of titanium in silicate rocks

A sensitive and highly selective aqueous as well as extractive spectrophotometric method has been developed for the determination of titanium(IV) using 2,3-dihydroxynaphthalene (H(2)ND) as a chromogenic agent. The reagent (H(2)ND) forms a 1:3 (TiOH(3+):ligand) complex at pH 4-9. The molar absorptivity and Sandell's sensitivity are 3.2 x 10(4) l . mol(-1)mol . cm(-1) and 0.001 microg/cm(2), respectively at lambda(max) 375 nm. The method has been found highly selective for Ti(IV) determination in rock samples. Solvent extraction of Ti(IV) in ethylacetate greatly improves the detection limit of the method. The method has been successfully applied to diverse silicate rock samples and results obtained are favourably comparable with those obtained from the tiron method. The reagent (H(2)ND) used in the present investigation is a much better variant than tiron for titanium(IV) determination in silicate rock samples in terms of sensitivity, selectivity, operational simplicity and economy.     

Study of the titanium-phenylfluorone complex formed in the presence of Triton X-305 and emulsifier OP

A highly sensitive method for the spectrophotometric determination of titanium with phenylfluorone (PF) in the presence of Triton X-305 and emulsifier OP has been developed. In acid medium (pH 1.4-2.2) Ti(IV) forms red-violet complexes with PF, Triton X-305 and OP. The complex exhibits maximum absorption at 540 nm. The molar absorptivity is 1.63 x 10(5) 1.mole(-1).cm(-1). The Ti:PF ratio in the complex is 1:2. Beer's law is obeyed in the titanium concentration range 0-0.2 microg/ml in the final solution. Fluoride and EDTA interfere. The method has been used for the rapid direct determination of microamounts of Ti(IV) in soils and cereals with satisfactory results.     

Electroanalytical Study of the Pesticide Asulam

The electrochemical behaviour of the herbicide Asulam was studied by cyclic and square wave voltammetry. Asulam may be irreversibly oxidised at a glassy carbon electrode. Maximum currents were obtained at pH = 1.9 in aqueous electrolyte solution. Based on the electrochemical behaviour of Asulam, two analytical methodologies were developed for its determination in water samples, using square wave voltammetry (SWV) and flow injection analysis (FIA) coupled with an amperometric detector. Limits of detection of 7.1 2 10 m 6 mol L m 1 and 1.2 2 10 m 8 mol L m 1 for SWV and FIA respectively, were achieved. Repeatability was calculated by assessing the relative standard deviation (%) for 10 consecutive determinations of one sample. The found values were 2.1% for SWV and 5.0% for FIA. Validation of the results provided by SWV and FIA methodologies was performed by comparison with results from an HPLC-DAD technique. Good relative deviations were found (< 5%). Recovery trials were performed to assess the accuracy of the results and the obtained values were between 84% and 107% for both methods.     

Voltammetric determination of indium in alumina supported catalysts

A sensitive and rapid method for the estimation of trace levels of indium in alumina supported catalysts using square wave voltammetry (SWV) is discussed. The SWV method for indium in the alumina matrix is standardized using synthetic samples and good recoveries were obtained. Calibration graphs are linear in the range 1-5 mug/ml and the detection limit is 3.57 x 10(-8) g/ml. In order to determine the accuracy of the proposed method, the results obtained have been compared with those given by atomic absorption spectrophotometry (AAS). Statistical analysis shows no significant bias between the two methods. This technique is found suitable for the estimation of indium in the range 0.1-1.0% (w/w) in the catalyst samples with an RSD < 1.5%.     

石墨烯修饰玻碳电极在对苯二酚存在下选择性测定米吐尔

制备了石墨烯修饰玻碳电极(GN/GCE)。 在0.5 mol/L HAc-NaAc(pH=4.8)缓冲溶液中,用循环伏安法(CV)和方波伏安法(SWV)研究了米吐尔在修饰电极上的电化学行为,建立了测定米吐尔的新方法。 研究表明,米吐尔在GN/GCE上的氧化、还原峰电势差比其在裸玻碳电极(GCE)上的小,峰电流显著增加,说明GN/GCE对米吐尔有电催化作用;共存物对苯二酚干扰米吐尔的测定,通过方波伏安法可以消除其干扰。 在方波伏安曲线上,米吐尔的还原峰电流与其浓度在8.0×10^-8~5.0×10^-5 mol/L范围内呈线性关系,检出限为2.0×10^-8 mol/L。 该法可用于照相显影废液中米吐尔的测定。     

Nanomolar Determination of Methyldopa in the Presence of Large Amounts of Hydrochlorothiazide Using a Carbon Paste Electrode Modified with Graphene Oxide Nanosheets and 3‐(4′‐Amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic Acid

A novel electrochemical sensor for sensitive detection of methyldopa at physiological pH was developed by the bulk modification of carbon paste electrode (CPE) with graphene oxide nanosheets and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,′AA). Applying square wave voltammetry (SWV), in phosphate buffer solution (PBS) of pH 7.0, the oxidation current increased linearly with two concentration intervals of methyldopa, one is 1.0×10^?8–1.0×10^?6 M and the other is 1.0×10^?6–4.5×10^?5 M. The detection limit (3σ) obtained by SWV was 9.0 nM. The modified electrode was successfully applied for simultaneous determination of methyldopa and hydrochlorothiazide. Finally, the proposed method was applied to the determination of methyldopa and hydrochlorothiazide in some real samples.     

A Sensitive Electrochemical Sensor for Voltammetric Determination of Ganciclovir Based on Au‐ZnS Nanocomposite

An electrode modified with ZnS and gold nanoparticles (Au‐ZnS NPs) is introduced for highly sensitive voltammetric determination of ganciclovir (GCV). Surface structure and topography of the modified electrode was studied by SEM, EDX and XRD techniques. Electrochemical oxidation of GCV was investigated by cyclic (CV) and square wave voltammetry (SWV) in Briton‐Robinson buffer solution (pH 1.5). The results showed that electrochemical oxidation of GCV at the Au‐ZnS modified glassy carbon electrode (GCE) is irreversible and exhibited diffusion controlled electrode process over the pH range from 1.0 to 6.0. The oxidation potential peak and pH relationship showed that electrons and protons were transferred simultaneously over the electrochemical oxidation process. Using the proposed sensor, the linear calibration curves were obtained in the ranges of 0.04–1.50 μM and 1.5–70.0 μM with detection limit of 0.01 μM GCV by SWV technique. The modified electrode was successfully applied as a sensitive, reproducible and repeatable sensor for determination of the trace amount of GCV in human serum, urine and cymevene vials. Reasonable results were obtained from comparing the measurements of the real samples by the new sensor to high performance liquid chromatography (HPLC) as a standard method.     

Electrochemical Detection of β-Lactoglobulin Allergen Using Titanium Dioxide/Carbon Nanochips/Gold Nanocomposite-based Biosensor

A label-free electrochemical immunosensor was developed for the ultra-sensitive detection of β-lactoglobulin (β-LG). The novel nanocomplex of carbon nanochips, colloidal gold nanoparticles and titanium dioxide nanoparticles TiO₂/CNC/AuC were constructed on conducting polymer, chitosan, and were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). This nanocomplex interface was studied using cyclic voltammetry (CV) and showed great improvement at the gold electrode surface with enhanced electrochemical performance, sensitivity and selectivity for β-lactoglobulin. Under optimal parameters, the square wave voltammetry (SWV) response curve was determined from 0.01 pg/mL to 500 pg/mL using [Fe(CN)₆]^3−/4−] redox probe. The calibration plot illustrates a linear relationship between log β-LG concentration and SWV current, with the limit of detection determined to be 0.01 pg/mL. This immunosensor displayed high sensitivity, selectivity, reproducibility and stability, and can be utilised for the detection of β-LG in real food samples.     

Platinum,Rhodium, Palladium and Lead: Elements Linked to Vehicle Emissions. Their Simultaneous Voltammetric Determination in Superficial Water

The present work, regarding the determination of Pt(II), Rh(III) by square‐wave adsorption stripping voltammetry (SWAdSV), Pd(II) by square‐wave voltammetry (SWV) and Pb(II) by square‐wave anodic stripping voltammetry (SWASV) in superficial water is an interesting example of the possibility to simultaneously, or better sequentially determine each single element in real samples. The critical comparison between peak area and peak current highlights that lower limits of detection are obtained if peak area is employed as instrumental datum. 0.6 mmol/L formaldehyde+1.2 mmol/L hydrazine (formazone complex) in 0.3 mol/L HCl and ammonia‐ammonium chloride buffer pH 9.6 were employed as the supporting electrolytes. The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR‐CRM 403 and Fresh Water NIST‐SRM 1643d. Precision and accuracy, expressed as relative standard deviation and relative error, respectively, were generally lower than 6% in all cases. Once set up on the standard reference materials, the analytical procedure was transferred and applied to superficial water sampled in proximity to superhighway and in the Po river mouth area. A critical comparison with spectroscopic measurements is also discussed.     

Voltammetric Investigation and Determination of Mefloquine

The electrochemical reduction behavior of mefloquine HCl (MEF), the antimalarial drug, was studied in aqueous alcoholic media at a hanging mercury drop electrode. Cyclic voltammetric studies showed one well‐defined reduction peak and one ill‐defined reduction wave between pH 1.5 and 12.03. The reduction was found as irreversible or quasireversible depending on pH and exhibited diffusion controlled process. The mechanism of reduction process was discussed. A systematic study of the experimental parameters that affect the differential pulse and square wave response was carried out and the optimized experimental conditions were obtained. The calibration plots were derived for the determination of MEF in pharmaceutical dosage forms and biological samples. DPV and SWV techniques for the determination of MEF in Britton–Robinson buffer at pH 11.10, which allows quantitation over the 6×10^?6 to 8×10^?5 M range in the supporting electrolyte, were proposed. The linear response was obtained in samples in the ranges of 6×10^?6 to 6×10^?5 M for both techniques. These methods are fully validated. The standard addition method was used in the biological media. No electroactive interferences from the excipients and endogenous substances were found in tablets and biological fluids.     

Palladium nanoparticle decorated carbon ionic liquid electrode for highly efficient electrocatalytic oxidation and determination of hydrazine

In this work arrays of palladium nanoparticles were synthesized on carbon ionic liquid electrode (CILE) (Pd/CILE), and the electrocatalytic oxidation of hydrazine was investigated using this electrode. Electrochemical oxidation of hydrazine in phosphate buffer (pH 7) was performed using cyclic voltammetry and square wave voltammetric techniques (SWV). Using the proposed electrode, a highly reproducible and well-defined peak was obtained for hydrazine at a very low potential of −0.02 V versus Ag/AgCl. A linear dynamic range of 5-800 μM with an experimental detection limit of 0.82 μM was obtained. These results show that the proposed electrode displays better electrocatalytic activity compared to the previously reported palladium modified electrodes towards oxidation of hydrazine.     

Electrochemical behaviour of sertraline at a hanging mercury drop electrode and its determination in pharmaceutical products

The electrochemical behaviour of sertraline at a hanging mercury drop electrode (HMDE) was described. Different voltammetric techniques, such as cyclic, linear sweep, differential pulse and square wave voltammetry, were used. Voltammograms were obtained at different pH values with a Britton-Robinson buffer solution used as supporting electrolyte. The best results were found by square wave voltammetry with electrodeposition at alkaline pH using a borate buffer with a pH = 8.2 for the samples, containing 12% (v/v) methanol. Under optimised conditions, a linear relationship between 2.33 x 10(-7) and 3.15 x 10(-6) M of sertraline with a limit of detection of 1.98 x 10(-7) M was obtained. The electrochemical method developed was applied to the determination of sertraline in pharmaceutical formulations. Recoveries were close to 100%, thus proving efficacy of the proposed method for the quantification of sertraline in commercial samples.     

Mercury meniscus on solid silver amalgam electrode as a sensitive electrochemical sensor for tetrachlorvinphos

The in-house prepared mercury meniscus modified solid silver amalgam electrode (m-AgSAE) was successfully applied for the detection of organophosphate pesticide tetrachlorvinphos in pH 7 buffer solution. The electrochemical performance of m-AgSAE for the reduction of tetrachlorvinphos was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV), respectively. The surface morphology of solid silver electrode (AgE), as-amalgamated solid silver amalgam electrode (AgSAE), and polished solid silver amalgam electrode (p-AgSAE) was examined by field emission scanning electron microscopy (FESEM). Among the applied techniques, DPV and SWV analysis showed a remarkable increase in the reduction peak current and provided a simple, fast, and sensitive method for the determination of tetrachlorvinphos. The electrochemical impedance spectroscopy (EIS) was used to correlate the electrocatalytic activity of AgSAE, p-AgSAE and m-AgSAE with their interfacial charge transport capabilities. Under the optimized experimental conditions, the DPV and SWV responses were linear over the 1–9 μM and 10–50 μM concentration ranges with a detection limit of 0.06 μM for DPV and 0.04 for SWV. The estimation of tetrachlorvinphos in the ground and waste water samples with the proposed method was in good agreement with that of the added amount. The proposed electrochemical method not only extends the application of non-toxic m-AgSAE, but also offers new possibilities for fast and sensitive analysis of tetrachlorvinphos and its structural analogs in environmental samples.