Voltammetric behavior of vitamin B(2) on the gold electrode modified with a self-assembled monolayer of l-cysteine and its application for the determination of vitamin B(2) using linear sweep stripping voltammetry

The voltammetric behavior of Vitamin B(2) (VB(2)) has been studied at the gold electrode modified with a self-assembled monolayer of l-cysteine. The voltammetric responses are evaluated with respect experimental conditions, such as composition and pH of the supporting electrolyte, concentration of VB(2), accumulation potential and accumulation time. On basis of the voltammetric behavior a highly sensitive method is present for the determination of VB(2) by using linear sweep stripping volammetry. The method is suitable for the determination of VB(2) concentrations between 5.0x10(-11) and 5.0x10(-6) mol l(-1). And the detection limit can be reached to 2.5x10(-11) mol l(-1). The method is applied to determine the concentration of VB(2) in the tablets with satisfactory results.     

Trace measurements of colchicine by adsorptive stripping voltammetry

A highly sensitive voltammetric method for trace measurements of the alkaloid colchicine is described. The method is based on the controlled adsorptive accumulation of the drug at the hanging mercury drop electrode, followed by voltammetric determination of the surface species. The adsorptive stripping response is evaluated with respect to preconcentration time and potential, solution pH, voltammetric waveform and other variables. With a 10-min preconcentration, a detection limit of 1.3 x 10(-10)M is obtained. The relative standard deviation (at the 1 x 10(-7)M level) is 1.1%. Applicability to urine analysis is illustrated.     

Selective determination of trace copper(II) by cathodic adsorptive stripping voltammetry with a naphthol-derivative Schiff's base

A selective and sensitive stripping voltammetric method for the determination of trace amounts of copper(II) with a recently synthesized naphthol-derivative Schiff's base (2,2'-[1,2-ethanediylbis(nitriloethylidyne)]bis(1-naphthalene)) is presented. The method is based on adsorptive accumulation of the resulting copper-Schiff's base complex on a hanging mercury drop electrode, followed by the stripping voltammetric measurement at the reduction current of adsorbed complex at -0.15 V (vs. Ag/AgCl). The optimal conditions for the stripping analysis of copper include pH 5.5 to 6.5, 8 microM Schiff's base and an accumulation potential of -0.05 V (vs. Ag/AgCI). The peak current is linearly proportional to the copper concentration over a range 2.3-50.8 ng ml(-1) with a limit of detection of 1.9 ng ml(-1). The accumulation time and RSD are 90 s and (3.2-3.5)%, respectively. The method was applied to the determination of copper in some analytical grade salts, tap water, human serum and sheep's liver.     

Adsorptive stripping voltammetric determination of copper(II) ion using phenyl pyridyl ketoneoxime (PPKO)

A sensitive and selective procedure is presented for the voltammetric determination of copper(II) ion. The procedure involves an adsorptive accumulation of Cu2+-PPKO on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of reduction current of adsorbed complex at about -0.30 V (vs. SCE). The optimum conditions for the analysis of copper(II) ion include pH (5.8-7.0), 60 microgM PPKO and an accumulation potential of -0.5 V (vs. SCE). The peak current is proportional to the concentration of copper over the range 0.3-76 ng mL(-1) with a detection limit of 0.01ng mL(-1) with an accumulation time of 60 s. The speciation of different forms of complex between copper(II) ion and PPKO, using the Best (Martell program), followed pH measurement were examined. The method was applied to the determination of copper(II) ion content in real samples successfully.     

Square wave adsorptive voltammetric determination of sunset yellow

Square wave adsorptive stripping voltammetry was used for determining trace amounts of dye Sunset Yellow (E-110) for the first time. Its adsorptive voltammetric behaviour followed by a square wave mode step was investigated at different pH media. Sunset Yellow in 0.5 M NH (4)Cl NH (3) buffer solution gave an adsorptive stripping voltammetric peak at the hanging mercury drop electrode at -0.60 V using an accumulation potential of -0.40 V. The effect of experimental parameters that affected this determination are discussed. The calibration graph to determine Sunset Yellow was linear in the range 5-90 mug 1(-1), obtaining a relative standard deviation of 2.2% for a solution of 30 mug 1(-1) (n = 10) in the same day. The determination limit was 5 mug 1(-1) after 15 s of accumulation at -0.40 V. The proposed method was applied to determine this dye in several commercial refreshing drinks, which contained small amounts of this compound. Measurements were made directly over diluted solutions of commercial samples. Similar results were obtained between adsorptive stripping square-wave voltammetric values and the obtained by application of a HPLC method with spectrophotometric detection.     

Voltammetric determination of diethylstilbestrol at carbon paste electrode using cetylpyridine bromide as medium

In this paper, the voltammetric properties of diethylstilbestrol (DES) at the carbon paste electrode were described. The oxidation peak currents of DES increase significantly in the presence of surfactant cetylpyridine bromide (CPB), compared with that in the absence of CPB. Based on this fact, a voltammetric technique for determining DES is proposed. The accumulation potential has no effects on the peak current of the DES. An open-circuit accumulation is carried out. The experimental parameters, such as pH value of buffer, scan rate, and accumulation time were optimized. The interferences of some metal ions and organic compounds have also been studied, and some metal ions almost do not interfere with the determination of DES. Using this voltammetric method, DES in the injection sample was measured. The results show that this voltammetric method is reliable for the practice determination of DES.     

Determination of ketorolac in human serum by square wave adsorptive stripping voltammetry

The adsorption behavior of ketorolac on a hanging mercury drop electrode (HMDE) was explored by square-wave and cyclic voltammetry. The square wave voltammetric response of ketorolac depends on the parameters of the square wave voltammetry excitation signal as well as on the pH of the medium and the accumulation time. The drug was accumulated at HMDE and a well-defined peak was obtained at -1.41 V versus. Ag/AgCl (saturated KCl) in acetate buffer of pH 5.0. A square-wave adsorptive stripping voltammetric method for the quantitative determination of ketorolac was developed. The linear concentration range was 1x10(-10)-1x10(-8) when using 300 s accumulation at -0.8 V. The detection limit of ketorolac was 1.0x10 (-11)M . The precision was excellent with relative standard deviation of 3.85% at concentration of 5x10 (-8)M after 60 s accumulation time. Applicability to serum samples was illustrated. A detection limit of 14 ng per ml of serum was obtained.     

Simple and Highly Selective Catalytic Adsorptive Voltammetric Method for Cr(VI) Determination

A simple and highly selective and sensitive catalytic adsorptive stripping voltammetric procedure for determination of traces of Cr(VI) in the presence of a large excess of Cr(III) in environmental water samples is reported. To obtain a low detection limit the voltammetric procedure of chromium determination in the presence of DTPA and nitrate was exploited. For elimination of interference of Cr(III) ethylenediaminedisuccinic acid was used as a masking agent. At optimized conditions the calibration graph is linear from 2×10^?10 to 2×10^?8 mol L^?1 for accumulation time of 30 s. The validation of the procedure was performed by comparison of the results of analysis of river water samples with those obtained using other accepted voltammetric procedure.     

Anodic stripping voltammetric determination of silver ion at a carbon paste electrode modified with carbon nanotubes

A carbon paste electrode (CPE) was modified with multi-wall carbon nanotubes and successfully applied to the determination of silver ion by differential pulse anodic stripping voltammetry. Compared to a conventional CPE, a remarkably improved peak current response and sensitivity is observed. The analytical procedure consisted of an open circuit accumulation step for 2?min in ?0.4?V, this followed by an anodic potential scan between +0.2 and?+?0.6?V to obtain the voltammetric peak. The oxidation peak current is proportional to the concentration of silver ion in the range from 1.0?×?10^?8 to 1.0?×?10^?5?mol?L^?1, with a detection limit of 1.8?×?10^?9?mol?L^?1 after an accumulation time of 120?s. The relative standard deviation for 7 successive determinations of Ag(I) at 0.1???M concentration is 1.99%. The procedure was validated by determining Ag(I) in natural waters.

Adsorptive-catalytic stripping measurements of ultratrace vanadium in the presence of cupferron and bromate

An extremely sensitive stripping voltammetric procedure for ultratrace measurements of vanadium is reported. The method is based on the interfacial accumulation of the vanadium-cupferron complex onto the hanging mercury drop electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. The dual amplification effect associated with these accumulation and catalytic processes results in a detection limit of 4.9 x 10(-12)M (0.25 ppt). The relative standard deviation (at 50 ppt) is 1.6%. The procedure is also very selective. Such coupling of catalytic and adsorptive collection processes holds great promise for the development of an ultrasensitive voltammetric procedure for other trace metals.     

Electroanalysis of some common pesticides using conducting polymer/multiwalled carbon nanotubes modified glassy carbon electrode

The cyclic voltammetric behaviour of three common pesticides such as isoproturon (ISO), voltage (VOL) and dicofol (DCF) was investigated at glassy carbon electrode (GCE), multiwalled carbon nanotubes modified GCE (MWCNTs/GCE), polyaniline (PANI) and polypyrrole (PPY) deposited MWCNT/GCE. The modified electrode film was characterized by scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). The electroactive behaviour of the pesticides was realized from the cyclic voltammetric studies. The differential pulse voltammetric principle was used to analyze the above-mentioned pesticides using MWCNT/GCE, PANI/MWCNT/GCE and PPY/MWCNT/GCE. Effects of accumulation potential, accumulation time, Initial scan potential, amplitude and pulse width were examined for the optimization of stripping conditions. The PANI/MWCNT/GCE performed well among the three electrode systems and the determination range obtained was 0.01-100 mgL(-1) for ISO, VOL and DCF respectively. The limit of detection (LOD) was 0.1 microgL(-1) for ISO, 0.01 microgL(-1) for VOL and 0.05 microgL(-1) for DCF on PANI/MWCNT/GCE modified system. It is significant to note that the PANI/MWCNT/GCE modified system results in the lowest LOD in comparison with the earlier reports. Suitability of this method for the trace determination of pesticide in spiked samples was also realized.     

Voltammetry of biologically active species and surfactants on new miniaturized and contractible (compressible) mercury electrodes

The adsorption of the polyether-antibiotic monensin from an aqueous solution on mercury was used to investigate the effect of the decreasing size of a stationary mercury drop electrode on the shape of the voltammetric desorption peak of the surfactant. The change of the i-E curve indicated an acceleration of the transport of the surfactant to the electrode as well as of time-dependent changes in the adsorption layer. A decrease of the radius of the hanging mercury drop electrode from 220 μm to 80 μm at a constant accumulation time of t_ac = 70 s resulted in an about 4-fold increase of the evaluated signal (i-E pre-wave) of monensin. A 7-fold increase of the voltammetric desorption peak of monensin at conc. 5 · 10^–7 mol/L was observed as result of a compressive accumulation of the surfactant due to a contraction of the mercury drop electrode. A scheme of an apparatus for voltammetric/polarographic measurements by means of the contractible (compressible) mercury drop electrode is described. The controlled contraction of the electrode surface is presented together with preliminary results covering a new way of accumulation of surfactants, new accumulation effects, effective in adsorptive voltammetry, and other electroanalytical techniques.     

Simultaneous determination of zinc,copper, lead,and cadmium in fuel ethanol by anodic stripping voltammetry using a glassy carbon–mercury-film electrode

A new, versatile, and simple method for quantitative analysis of zinc, copper, lead, and cadmium in fuel ethanol by anodic stripping voltammetry is described. These metals can be quantified by direct dissolution of fuel ethanol in water and subsequent voltammetric measurement after the accumulation step. A maximum limit of 20% (v/v) ethanol in water solution was obtained for voltammetric measurements without loss of sensitivity for metal species. Chemical and operational optimum conditions were analyzed in this study; the values obtained were pH 2.9, a 4.7-m thickness mercury film, a 1,000-rpm rotation frequency of the working electrode, and a 600-s pre-concentration time. Voltammetric measurements were obtained using linear scan (LSV), differential pulse (DPV), and square wave (SWV) modes and detection limits were in the range 10^–9–10^–8 mol L^–1 for these metal species. The proposed method was compared with a traditional analytical technique, flame atomic absorption spectrometry (FAAS), for quantification of these metal species in commercial fuel ethanol samples.     

Differential pulse polarography and voltammetry of di-2-pyridyl ketone benzoylhydrazone

Summary The differential pulse polarographic (DPP) and voltammetric (DPV) behaviour of di-2-pyridyl ketone benzoylhydrazone (DPKBH), has been investigated over a wide pH range (2.1–11.5). The effect of various operational parameters on the reduction current are discussed and the mechanism of the electrode reaction is also included. Both methods DPP and DPV are applied for the analytical determination of this reagent and the detection limits are found to be 1.24 mol/l and 0.86 mol/l, respectively. The DPP behaviour of DPKBH in the presence of Pb(II), Cd(II) and Cu(II) is studied and the behaviour of the Cu(II)-DPKBH complex is fully investigated. The voltammetric determination of Cu(II), based on the accumulation of its complex at the hanging mercury drop electrode, is described. Statistical analysis of the calibration curve data is included.On leave from Assuit University, Egypt     

Detection of lead(II) using an glassy carbon electrode modified with Nafion, carbon nanotubes and benzo-18-crown-6

A glassy carbon electrode was modified with Nafion, carbon nanotubes and benzo-18-crown-6 to give an electrode for the selective determination of lead(II) via square wave anodic stripping voltammetry. The use of carbon nanotubes with their extraordinary electrical conductivity and strong adsorption ability warrants high sensitivity. Benzo-18-crown-6 is employed as a “molecular scavenger” because of its excellent selectivity for lead(II). The modified electrode shows enhanced sensitivity, reproducibility and selectivity for lead(II) even without applying an electrical potential during the accumulation time. It responds linearly to lead(II) in the 1 to 30 nM concentration range (with a correlation coefficient of 0.9992) after a 10-min accumulation time. The detection limit is 1 nM. The sensor exhibits excellent selectivity over other heavy metal ions such as Cd(II), Cu(II), Zn(II), and Hg(II).

Voltammetric Behavior of Strychnine, and its Determination in Strychno Nux-Vomica Seeds Extract

The voltammetric behavior of strychnine has been studied with a pyrolytic graphite (PG) electrode. The redox process taking place at the PG electrode is discussed. The cyclic voltammetric response has also been evaluated with respect to various experimental conditions, such as scan rate, pH of the supporting electrolyte, strychnine concentrations and accumulation time. A highly sensitive voltammetric method for the determination of strychnine is consequently developed. The linear calibration is in the range of 1×10⁻⁶ M – 1.1×10⁻⁴ M, with the limit of detection (LOD) being 1×10⁻⁸ M. The precision is excellent with a relative standard deviation (RSD) of 2.3%. The proposed cyclic voltammetric methodology has been applied to the determination of strychnine in the extract of Strychno nux-vomica seeds using the standard addition method. Consistent results have been obtained from both the electrochemical approach described here and the previously reported HPLC method.     

Determination of ametryn in soils via microwave-assisted solvent extraction coupled to anodic stripping voltammetry with a gold ultramicroelectrode

An extraction-anodic adsorptive stripping voltammetric procedure using microwave-assisted solvent extraction and a gold ultramicroelectrode was developed for determining the pesticide ametryn in soil samples. The method is based on the use of acetonitrile as extraction solvent and on controlled adsorptive accumulation of the herbicide at the potential of 0.50 V (vs. Ag/AgCl) in the presence of Britton-Robinson buffer (pH 3.3). Soil sample extracts were analysed directly after drying and redissolution with the supporting electrolyte but without other pre-treatment. The limit of detection obtained for a 10 s collection time was 0.021 g g^–1. Recovery experiments for the global procedure, at the 0.500 g g^–1 level, gave satisfactory mean and standard deviation results which were comparable to those obtained by HPLC with UV detection.     

Trace measurements of rhodium by adsorptive stripping voltammetry

A sensitive stripping voltammetric procedure for quantifying rhodium is described. The complex of rhodium with chloride ions is adsorbed on the hanging mercury drop electrode, and the reduction current of the accumulated complex is measured during a negative-going scan. Cyclic voltammetry is used to characterize the interfacial and redox behaviors. The effect of pH, chloride concentration, accumulation potential and other variables is discussed. The detection limit is 1 x 10(-8)M ( approximately 1 ng/ml) with 5-min accumulation. A linear current-concentration relationship is observed up to 7 x 10(-7)M and the relative standard deviation (at the 2 x 10(-7)M level) is 3.0%. Possible interferences by co-existing metals are investigated.     

Trace measurement of dipyridamole by adsorptive stripping voltammetry

A sensitive adsorptive stripping voltammetric method for trace measurement of dipyridamole in alkaline solution is described. The method is based on the adsorptive accumulation of the drug at the hanging mercury drop electrode, followed by linear sweep voltammetric determination. The response is evaluated with respect to percentage of ethanol, preconcentration time and potential, and concentration of NaOH. The detection limit of 1.0 x 10(-9)M is obtained under optimized conditions with a 5-min preconcentration. Applicability to injection, tablets and urine analysis is illustrated.     

Determination of iron(II) with chemically-modified carbon-paste electrodes

The utility of carbon-paste electrodes modified with 2,2'-bipyridyl and Nafion for the differential pulse voltammetric determination of iron(II) in aqueous medium is demonstrated. The method is based on formation of the 2,2'-bipyridyl complex of iron(II) and its accumulation by the Nafion. The differential pulse voltammetric response of the accumulated complex is used as the analytical signal. The response was evaluated with respect to carbon-paste composition, preconcentration time, pH, iron(II) concentration and other variables. A 3-min accumulation period permits measurement of iron(II) down to 10(-8)M, and a relative standard deviation of 3.8% for 2 x 10(-6)M iron(II). Rapid and convenient chemical renewal allows use of a single modified carbon-paste electrode in multiple analytical measurements over several days. The proposed procedure was applied to the determination of iron in certified standard reference materials and trace iron in natural waters.